Effect of carbon‐based nanoparticles on the cure characteristics and network structure of styrene–butadiene rubber vulcanizate

The network structure of styrene–butadiene rubber (SBR) in the presence of carbon black (CB) with two different structures and multi‐walled carbon nanotubes (MWCNTs) was investigated. Swelling behaviour, tensile properties at various strain rates and cure kinetics were characterized. Experimental data were analysed using the Flory–Rehner model as well as the tube model theory. It is found that the network structure of CB‐filled SBR follows a three‐phase composite model including rigid particles, semi‐rigid bound rubber and matrix rubber. This bound rubber is postulated to be critical for the mechanical and deformational properties, development of crosslinking density in matrix rubber and polymer–filler interaction. For MWCNT‐filled SBR, the bound rubber does not show a substantial contribution to the network structure and mechanical performance, and these properties are greatly dominated by the higher aspect ratio and polymer–filler interaction. Additionally it is deduced that the crosslinking density of matrix rubber increases on incorporation of the fillers compared to unfilled matrix rubber. Copyright © 2012 Society of Chemical Industry     

Reinforcement effects in fractal-structure-filled rubber

A quantitative morphological analysis has been performed using AFM and SAXS measurements in order to determine the spatial distribution of fillers in silica SBR composites. The proportion of fillers in agglomerates or aggregates of silica has thus been separated. Additional measurements have been carried out to quantify the amount of modified polymer in the vicinity of the filler surface, i.e. the bound rubber. It is shown that the reinforcing phase, constituting both silica particles and bound rubber, can be considered either as the dispersed or the continuous phase depending on the filler content.The linear dynamic mechanical properties of composites are then analysed. The variations of the shear modulus as a function of the filler content are then related to either the reinforcement effect induced by fillers or the development of specific additional interactions between phases, i.e. the interface effects. To separate the respective contribution of these effects from the overall dynamic behaviour of composites, micromechanical modelling is then performed. In a first step, the viscoelasticity of composites reinforced by 5.7 vol% of silica is predicted with the help of Christensen and Lo's model. For composites filled with 10 and 15 vol% of silica, self-consistent modelling, applied in a reverse mode, confirmed that the reinforcing phase, i.e. silica particles and bound rubber, acts as the continuous phase, in agreement with the morphological analysis. From the predicted dynamic mechanical properties of the reinforcing phase, the bound rubber behaviour is thus extracted as a function of the filler content and compared to that of unfilled SBR.     

Dynamic mechanical properties of SBR and EPDM vulcanisates filled with cryogenically pulverized flexible polyurethane foam particles

The dynamic mechanical properties of rubber vulcanisates filled with cryogenically pulverized polyurethane foam particles, used as a reinforcing filler, were investigated with respect to storage modulus (E′), loss modulus, and the variation of glass transition temperature. Two rubbers were using styrene–butadiene rubber (SBR) and ethylene–propylene copolymer (EPDM). The effects of filler concentration and filler characteristics (such as particle size and moisture content) were also monitored. It was found that the optimum dynamic mechanical properties of the compounds were obtained when introducing the PU particles of 40–50 parts per hundred (pph) rubber in the SBR and 30 pph in the EPDM, the properties being affected by the size of PU particles and moisture content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1129–1139, 1999     

Fly ash particles and precipitated silica as fillers in rubbers. I. Untreated fillers in natural rubber and styrene–butadiene rubber compounds

In this study, we investigated the effects of untreated precipitated silica (PSi) and fly ash silica (FASi) as fillers on the properties of natural rubber (NR) and styrene–butadiene rubber (SBR) compounds. The cure characteristics and the final properties of the NR and SBR compounds were considered separately and comparatively with regard to the effect of the loading of the fillers, which ranged from 0 to 80 phr. In the NR system, the cure time and minimum and maximum torques of the NR compounds progressively increased at PSi loadings of 30–75 phr. A relatively low cure time and low viscosity of the NR compounds were achieved throughout the FASi loadings used. The vulcanizate properties of the FASi‐filled vulcanizates appeared to be very similar to those of the PSi‐filled vulcanizates at silica contents of 0–30 phr. Above these concentrations, the properties of the PSi‐filled vulcanizates improved, whereas those of the FASi‐filled compounds remained the same. In the SBR system, the changing trends of all of the properties of the filled SBR vulcanizates were very similar to those of the filled NR vulcanizates, except for the tensile and tear strengths. For a given rubber matrix and silica content, the discrepancies in the results between PSi and FASi were associated with filler–filler interactions, filler particle size, and the amount of nonrubber in the vulcanizates. With the effect of the FASi particles on the mechanical properties of the NR and SBR vulcanizates considered, we recommend fly ash particles as a filler in NR at silica concentrations of 0–30 phr but not in SBR systems, except when improvement in the tensile and tear properties is required. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2119–2130, 2004     

Shape controlled spherical (0D) and rod-like (1D) silica nanoparticles in silica/styrene butadiene rubber nanocomposites: Role of the particle morphology on the filler reinforcing effect

Silica/styrene butadiene rubber (SBR) nanocomposites were prepared by blending method using shape-controlled spherical and rod-like nanoparticles with different aspect ratios as filler for the rubber reinforcement. The differently shaped silica particles were synthesized by sol–gel method using tetraethoxysilane (TEOS) and (3-mercaptopropyl) trimethoxysilane (MPTSM) as silica precursors, and cetyltrimethylammonium bromide (CTAB) as structure directing agent. This strategy allowed to study the influence of the particle morphology on the reinforcing effect independently of the silica surface chemistry and considering the aspect ratio as the only geometrical variance. Spherical and anisotropic rod-like particles, dispersed in the nanocomposites, formed a network of particles bridged by thin rubber layers throughout the SBR matrix. Moreover, differently oriented domains of aligned rods are observed when the aspect ratio of particles increases and is ≥2. Dynamic-mechanical properties demonstrated that the rod-like particles with the higher aspect ratio provided stronger reinforcement of the rubber. This was related to the self-alignment of the anisotropic particles and to the consequent larger filler/polymer interface, compared to that of spherical ones.     

Studies of reinforcement behavior of unique elastomer‐based nanocomposite gels

Unique nanocomposite (NC) gels were prepared by blending water swollen unmodified montmorillonite clay suspension with natural rubber (NR) and styrene‐butadiene rubber (SBR) latices followed by prevulcanization. These were extensively characterized by dynamic light scattering, solvent swelling, tensile, and dynamic mechanical measurements. Reinforcement behavior of NC gels was investigated by adding NC gels into virgin NR and SBR matrices at various loadings. The distribution and morphology of NC gels in the elastomer matrices was studied by X‐ray dot mapping and high‐resolution transmission electron microscopy. Experimental results indicated tremendous improvement of tensile strength (TS) and modulus of the NC gel‐filled matrices along with noticeable changes in dynamic mechanical and rheological properties. Compared with virgin NR, the TS of 16 phr NC gel‐filled NR system increased by 117%. Similar level of enhancement of TS was also registered for the NC gel‐filled SBR systems. NC gel‐filled systems showed higher shear viscosities and lower die‐swell values compared with their virgin counterparts. Contemporary particulate composite and nanofiller reinforcement models were used to understand the reinforcing behavior of these NC gels. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers     

Properties of silica‐filled styrene‐butadiene rubber compounds containing acrylonitrile‐butadiene rubber: The influence of the acrylonitrile‐butadiene rubber type

Because silica has strong filler‐filler interactions and adsorbs polar materials, a silica‐filled rubber compound exhibits poor dispersion of the filler and poor cure characteristics in comparison with those of a carbon black‐filled rubber compound. Acrylonitrile‐butadiene rubber (NBR) improves filler dispersion in silica‐filled styrene‐butadiene rubber (SBR) compounds. The influence of the NBR type on the properties of silica‐filled SBR compounds containing NBR was studied with NBRs of various acrylonitrile contents. The composition of the bound rubber was different from that of the compounded rubber. The NBR content of the bound rubber was higher than that of the compounded rubber; this became clearer for NBR with a higher acrylonitrile content. The Mooney scorch time and cure rate became faster as the acrylonitrile content in NBR increased. The modulus increased with an increase in the acrylonitrile content of NBR because the crosslink density increased. The experimental results could be explained by interactions of the nitrile group of NBR with silica. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 385–393, 2002     

Norbornylized soybean oil as a sustainable new plasticizer for rubbers with hybrid fillers

Carbon black (CB) and precipitated silica are two major reinforcing fillers in rubbers. CB/silica hybrid filler is also widely used in rubbers to provide balanced properties. CB/silica‐hybrid‐filler‐filled styrene‐butadiene rubber (SBR) containing naphthenic oil (NO), soybean oil (SO) and norbornylized SO (NSO) was investigated. The swelling and curing behavior and rheological, mechanical, thermal, aging and dynamic properties were studied and compared with earlier reported data on CB‐ or silica‐filled SBR. NSO provides better scorch safety and faster cure than SO. Compared with NO, the addition of SO and NSO enhances the thermal stability and aging resistance of SBR vulcanizates. SBR/NSO vulcanizates with hybrid filler exhibit a higher tensile and tear strength than SBR/NO and SBR/SO vulcanizates. A synergistic effect in the abrasion resistance of vulcanizates containing the hybrid filler is observed. An increase of sulfur content in the hybrid‐filler‐filled SBR/NSO vulcanizates provides further improvement in abrasion resistance, wet traction and rolling resistance. © 2017 Society of Chemical Industry     

Processing optimization of latex‐compounded montmorillonite/styrene‐butadiene rubber–polybutadiene rubber

Organo‐montmorillonite was incorporated into model tire tread formulations through latex compounding methods, to evaluate its effects on elastomer reinforcement and dynamic properties. An intercalation structure was obtained by applying latex compounding method to prepare organoclay‐emulsion stryene butadiene (E‐SBR) masterbatches, for compounding with organoclay loading levels of 0–20 parts per hundred rubber (phr). Microstructure, curing properties and tire performance of the compounded rubber were investigated with the aid of X‐ray diffraction, rheometor and dynamic‐mechanical analysis, respectively. The results showed that organo‐montmorillonite filler provided effective reinforcement in the elastomer matrix, as indicated through mechanical and dynamic mechanical properties. Tread compounds using higher organoclay loadings displayed preferred ice traction, wet traction, and dry handling, but decreased winter traction and rolling resistance. Model compounds using 15 phr of organoclay loading levels were preferred for balanced physical and dynamic properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41521.     

Fly‐ash particles and precipitated silica as fillers in rubbers. II. Effects of silica content and Si69‐treatment in natural rubber/styrene–butadiene rubber vulcanizates

This article explored the possibility of using silica from fly‐ash particles as reinforcement in natural rubber/styrene–butadiene rubber (NR/SBR) vulcanizates. For a given silica content, the NR : SBR blend ratio of 1 : 1 (or 50 : 50 phr) exhibited the optimum mechanical properties for fly‐ash filled NR/SBR blend system. When using untreated silica from fly‐ash, the cure time and mechanical properties of the NR/SBR vulcanizates decreased with increasing silica content. The improvement of the mechanical properties was achieved by addition of Si69, the recommended dosage being 2.0 wt % of silica content. The optimum tensile strength of the silica filled NR/SBR vulcanizates was peaked at 10–20 phr silica contents. Most mechanical properties increased with thermal ageing. The addition of silica from fly‐ash in the NR/SBR vulcanizates was found to improve the elastic behavior, including compression set and resilience, as compared with that of commercial precipitated silica. Taking mechanical properties into account, the recommended dosage for the silica (FASi) content was 20 phr. For more effective reinforcement, the silica from fly‐ash particles had to be chemically treated with 2.0 wt % Si69. It was convincing that silica from fly‐ash particles could be used to replace commercial silica as reinforcement in NR/SBR vulcanizates for cost‐saving and environment benefits. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

BIMS/filler interactions. I. Effects of filler structure

Polymer/filler interactions have been found to affect the performance of tire tread, sidewall, innerliner, or carcass and other industrial rubber products that are all based on filled elastomers. Identification of types of various polymer/filler interactions and ranking of their impacts have been elusive. Isobutylene-based polymers have relatively saturated structures and contain very low concentrations of functional group. Examples are BIMS (a brominated isobutylene/p-methylstyrene copolymer) containing p-bromomethylstyrene and p-methylstyrene; bromobutyl rubber containing  Br and olefin; chlorobutyl rubber containing  Cl and olefin; and butyl rubber containing olefin. On the other hand, high diene rubbers, such as polybutadiene rubber, polyisoprene rubber, and styrene/butadiene rubber, have unsaturated backbones and high olefin contents. Hence, different types and extents of interaction with reinforcing fillers, such as carbon black (CB) or silica, are expected in these two classes of elastomer. This work employs bound rubber (solvent extraction), viscoelasticity, stress–strain measurements, and solid state NMR to identify, differentiate, and scale polymer/filler interactions in unvulcanized BIMS/CB, BIMS/silica, SBR/CB, and SBR/silica composites, where SBR denotes a styrene/butadiene rubber. Four different types of CB and one type of silica have been studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4943–4956, 2006     

Al2O3的表面处理及粒子尺寸对SBR导热橡胶性能的影响

以丁苯橡胶为基质，微米氧化铝与纳米氧化铝为导热填料，制备了填充型导热橡胶，研究了微米氧化铝填充量，偶联剂表面处理对导热橡胶导热性能的影响。比较了纳米氧化铝和微米氧化铝填充的导热橡胶的导热性能及物理机械性能。并将2种粒子以不同配比加入了苯橡胶基质中，对其影响进行了探讨。结果表明，随着微米氧化铝填充份数的增加，丁苯橡胶的导热系数增大，但共加工性能和物理机械性能下降；用硅烷偶联剂KH-570，KH-550，A-151和钛酸酯偶联剂TM-S105表面处理后的微米氧化铝对导热橡胶的导热性能有一定影响，但并不显著，在相同填充量下，纳米氧化铝填充的导热橡胶比微米氧化铝填充的导热橡胶具有更好的导热性能及物理机械性能；在合适的比例下，纳米氧化铝与微米氧化铝混合填充的导热橡胶其导热效果优于单纯使用微米粒子填充的橡胶。     

Improvement of properties of silica‐filled styrene–butadiene rubber compounds using acrylonitrile–butadiene rubber

Since silica has strong filler–filler interactions and adsorbs polar materials, a silica‐filled rubber compound has a poor dispersion of the filler and poor cure characteristics. Improvement of the properties of silica‐filled styrene–butadiene rubber (SBR) compounds was studied using acrylonitrile–butadiene rubber (NBR). Viscosities and bound rubber contents of the compounds became lower by adding NBR to the compound. Cure characteristics of the compounds were improved by adding NBR. Physical properties such as modulus, tensile strength, heat buildup, abrasion, and crack resistance were also improved by adding NBR. Both wet traction and rolling resistance of the vulcanizates containing NBR were better than were those of the vulcanizate without NBR. The NBR effects in the silica‐filled SBR compounds were compared with the carbon black‐filled compounds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1127–1133, 2001     

Structure–property relationships of silica/silane formulations in natural rubber,isoprene rubber and styrene–butadiene rubber composites

The mechanical performance of natural rubber (NR), synthetic poly-isoprene rubber (IR), and styrene–butadiene rubber (SBR) composites filled with various silica/silane systems is investigated. The results are analyzed by referring to micro-mechanical material parameters, which quantify the morphological and structural properties of the polymer and filler network. These are obtained from fits with the dynamic flocculation model (DFM) describing the strongly nonlinear quasi-static stress–strain response of filler-reinforced elastomers as found from multihysteresis measurements of the investigated compounds. We focus on the reinforcement mechanisms of silica compounds with coupling and covering silane, respectively. The fitted material parameters give hints that the coupling silane provides a strong chemical polymer–filler coupling, which is accompanied by improved strength of filler–filler bonds for all three rubbers types. This may result also from the chemical coupling of short chains bridging adjacent silica particles. It implies larger stress values for the coupling silane and, in the case of NR and IR, a more pronounced “Payne effect” compared to the covering silane. In contrast, for SBR, the coupling silane delivers a lower Payne effect, which is explained by differences in the compatibility between rubber type and silane-grafted silica surface. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48435.     

Nanostructured fly ash–styrene butadiene rubber hybrid nanocomposites

Hybrid nanocomposites of styrene butadiene rubber (SBR) with nanostructured fly‐ash (NFA) were prepared in the laboratory by melt blending technique in an internal mixer. Curatives were added on a laboratory two‐roll mill. Curing characteristics as well as physico‐mechanical properties of the composites were evaluated. A comparison on SBR composites filled with fresh fly‐ash (FFA); carbon black (CB) and precipitated silica (PS) has been reported. In general, SBR‐NFA composites exhibit higher state of cure and higher strength properties as compared with HAF black‐filled and fresh fly‐ash‐filled SBR composites at equivalent loadings. This may be attributed to the higher reinforcing ability of NFA. This fact has also been supported by the swelling studies and Kraus' plot. Tear strength and abrasion resistance of the SBR‐NFA composites were superior to FFA‐filled and precipitated silica‐filled vulcanizates, but were inferior to carbon black‐ filled SBR vulcanizates. The SBR‐NFA composites showed lower hardness as compared with both the carbon black‐filled and silica‐filled composites. Transmission electron microscopy and scanning probe microscopy studies revealed that the NFA particles are well dispersed in the SBR matrix. These results were further supported by fracture surface analysis under the SEM, which revealed the role of NFA in the prevention of fracture propagation. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Preparation of nano‐zinc oxide/EPDM composites with both good thermal conductivity and mechanical properties

In this article, nano‐zinc oxide (ZnO) filled ethylene propylene diene monomer (EPDM) composites are prepared, and the mechanical (static and dynamic) properties and thermal conductivity are investigated respectively, which are further compared with the traditional reinforcing fillers, such as carbon black and nano‐silica. Furthermore, influence of in‐situ modification (mixing operation assisted by silane at high temperature for a certain time) with the silane‐coupling agent Bis‐(3‐thiethoxy silylpropyl)‐tetrasufide (Si69) on the nano‐ZnO filled composites is as well investigated. The results indicate that this novel reinforcing filler nano‐ZnO can not only perform well in reinforcing EPDM but can also improve the thermal conductivity significantly. In‐situ modification with Si69 can enhance the interfacial interaction between nano‐ZnO particles and rubber matrix remarkably, and therefore contribute to the better dispersion of filler. As a result, the mechanical properties and the dynamic heat build‐up of the nano‐ZnO filled composites are improved obviously by in‐situ modification, without influencing the thermal conductivity. In comparison with traditioanl reinforcing fillers, in‐situ modified nano‐ZnO filled composites exhibit the excellent performance in both mechanical (static and dynamic) properties and better thermal conductivity. In general, our work indicates that nano‐ZnO, as the novel thermal conductive reinforcing filler, is suitable to prepare elastomer products serving in dynamic conditions, with the longer expected service life. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Design and preparation of cross‐linked α‐methylstyrene‐acrylonitrile copolymer nano‐particles for elastomer reinforcement

Crosslinked α‐methylstyrene and acrylonitrile (MStAN) copolymer particles in a latex form were synthesized by free radical emulsion polymerization. The particles took a spherical shape with an average size of 53.1 nm in a narrow distribution. When filled into styrene‐butadiene rubber (SBR), nitrile‐butadiene rubber (NBR), and natural rubber (NR), the MStAN nano‐particles exhibited excellent reinforcing capabilities and the best in NBR. By the employment of heat treatment, mechanical properties of the MStAN‐filled SBR composites had got remarkable further improvements. But mechanical properties, together with the morphology, of the MStAN‐filled NBR composites, varied little after heat treatment, which, however, divulged the naturally good compatibility between the MStAN particles and the NBR matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

不同硫化体系对聚苯乙烯纳米粒子填充丁苯橡胶填料网络的影响

通过自由基乳液聚合工艺制备出了交联聚苯乙烯纳米粒子填充的丁苯橡胶复合材料;研究了硫黄、过氧化二异丙苯、过氧化二苯甲酰3种不同硫化体系,以及不同填料用量对复合材料体系中填料网络结构的影响。结果表明,交联聚苯乙烯纳米粒子在过氧化物交联硫化体系中形成的填料网络,较之硫黄硫化体系中更低,较低的硫化反应温度和热剪切的热处理方式,显著降低了填料的聚集。     

Synergistic effect of plasma‐modified halloysite nanotubes and carbon black in natural rubber—butadiene rubber blend

Halloysite nanotubes (HNTs) were investigated concerning their suitability for rubber reinforcement. As they have geometrical similarity with carbon nanotubes, they were expected to impart a significant reinforcement effect on the rubber compounds but the dispersion of the nanofillers is difficult. In this work, HNTs were surface‐modified by plasma polymerization to change their surface polarity and chemistry and used in a natural rubber/butadiene rubber blend in the presence of carbon black. The aim of the treatment was to improve the rubber–filler interaction and the dispersion of the fillers. A thiophene modification of HNTs improved stress–strain properties more than a pyrrole treatment. The surface modification resulted in a higher bound rubber content and lower Payne effect indicating better filler–polymer interaction. Scanning electron microscopy measurements showed an increased compatibility of elastomers and fillers. As visualized by transmission electron microscopy, the thiophene‐modified HNTs formed a special type of clusters with carbon black particles, which was ultimately reflected in the final mechanical properties of the nanocomposites. The addition of HNTs increased loss angle. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Nanocomposites based on epoxidized poly(styrene-co-butadiene) rubber and graphene nanoplatelets

Nanofillers play as reinforcing agents of the polymer matrix. The reinforcement and dynamic mechanical properties of nanocomposites based on filled epoxidized-poly(styrene-co-butadiene) rubber are investigated. The modification of the polymer matrix allows improvement in polymer–filler interaction, and thus the mechanical properties of the vulcanizates. Here, the rubber was modified by introducing the epoxy functional groups in the matrix. The quantification for epoxidation rate was analyzed by means of NMR and ~8.8% epoxidation was optimized. The nanocomposites were prepared by melt-mixing technique. The influence of rubber epoxidation in enhancing dynamic mechanical and thermal properties was demonstrated. Stable filler networking using exfoliated graphene nanoplatelets (xg C750) and carbon black (CB-N234) in epoxidized rubber is described through multihysteresis measurements. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47802.