Improved tensile properties of carbon nanotube modified epoxy and its continuous carbon fiber reinforced composites

Carbon nanotubes (CNTs) were used to improve the tensile properties of an epoxy resin and its continuous carbon fiber (CF) reinforced composites. Micrography picture showed that CNTs has been well incorporated into the composites, and made the fracture cross section more rougher through sharing the stress. For the CNT/epoxy composite, the tensile strength and modulus both increased upon the CNT addition, and at a CNT volume concentration of 2.0%, the maximum enhancements in the tensile strength and modulus were achieved as 26.7% and 21.5%, respectively. For the CNT‐CF/epoxy composite, the maximum enhancement in tensile strength was achieved as 11.6% at a CNT volume concentration of 1.0% and then decreased with the further increase of the CNT addition, but the tensile modulus increased monotonically upon the CNT addition. POLYM. COMPOS., 36:1664–1668, 2015. © 2014 Society of Plastics Engineers     

Evaluation of mechanical properties of untwisted carbon nanotube yarn for application to composite materials

Carbon nanotubes (CNTs) with superior mechanical properties have been of interest as reinforcement for polymer composites. However, the length of individual CNTs is limited. As a solution, yarns spun by twisting together multi-walled carbon nanotubes (MWCNTs) have been reported. In this study, untwisted CNT yarns were prepared by a non-conventional method drawing CNTs through a die. The MWCNTs in these yarns are held together by strong van der Waals forces that arise due to the interactions on the long and smooth surfaces of the MWCNTs. Here, mechanical properties of untwisted CNT yarn were studied by tensile tests. The strength of the CNT yarn was increased by increasing the apparent density of the yarn. The CNT yarns showed high tensile strength of 1 GPa and elastic modulus of 79 GPa at a yarn diameter of 35 μm. The interfacial shear strength between the CNT yarn and epoxy resin was studied by the microdroplet method, and it was very low. The wettability of the CNT yarn was affected by a type of curing agent. A unidirectional composite of epoxy resin and CNT yarn was prepared by the pultrusion molding method. Mechanical properties of the unidirectional composite were affected by the type of curing agent.     

Dispersion, interfacial interaction and re-agglomeration of functionalized carbon nanotubes in epoxy composites

The surface, interfacial and dispersion properties of carbon nanotubes (CNTs), and the mechanical properties of the CNT/epoxy composites affected by CNT functionalization are investigated. It is demonstrated that there exists strong correlations between amino-functionalization, dispersion, wettability, interfacial interaction and re-agglomeration behaviour of CNTs and the corresponding mechanical and thermo-mechanical properties of CNT/epoxy composites. The amino-functionalized CNTs exhibit higher surface energy and much better wettability with epoxy resin than the pristine CNTs, and the attached amine molecules arising from the functionalization effectively inhibit the re-agglomeration of CNTs during the curing of resin. These ameliorating effects along with improved interfacial adhesion between the matrix and functionalized CNTs through covalent bonds result in improved flexural and thermo-mechanical properties compared with those without functionalization.     

Carbon nanotube/epoxy composites fabricated by resin transfer molding

Carbon nanotube (CNT)/epoxy composites with controllable alignment of CNTs were fabricated by a resin transfer molding process. CNTs with loading up to 16.5 wt.% were homogenously dispersed and highly aligned in the epoxy matrix. Both mechanical and electrical properties of the CNT/epoxy composites were dramatically improved with the addition of the CNTs. The Young’s modulus and tensile strength of the composites reach 20.4 GPa and 231.5 MPa, corresponding to 716% and 160% improvement compared to pure epoxy. The electrical conductivity of the composites along the direction of the CNT alignment reaches over 1 × 10⁴ S/m.     

Structure and properties of aeronautical composites using carbon nanotubes/epoxy dispersion as nanocomposite matrix

The structure and properties of hybrid multiscale composites containing carbon nanotubes (CNTs) was reported. CNTs were dispersed in epoxy by using high energy ultrasonication, followed by the fabrication of CNT hybrid composites via resin transfer molding (RTM) processing. The processability of CNTs/epoxy systems was explored by a capillary experiment. The dependences of mechanical and electrical properties of the hybrid composites on CNT content were investigated. Microscopic observation confirms the formation of CNTs percolation network. The different roles of CNT networks in mechanical reinforcement and electrical amelioration were analyzed. One explanation based on the dispersion and distribution of CNTs is proposed. It is found that the variations of the hybrid composites with respect to mechanical and electrical properties are attributed to the hierarchical structure in the hybrid composites. As far as the hybrid multiscale composites produced via RTM process is concerned, the formation of CNT percolation network, subjected to dynamic impregnation, is hindered by the presence of continuous fibrous reinforcement. The hierarchical structure influenced by several competing factors reveals great potential in being able to tailor the structural and functional performance of the CNT hybrid composites. The effects of CNTs on the dimensional stability of polymer based composites are also assessed. POLYM. COMPOS., 34:1690–1697, 2013. © 2013 Society of Plastics Engineers     

Raman microscopy of residual strains in carbon nanotube/epoxy composites

Carbon nanotube (CNT) strain variations with temperature, as measured with Raman microscopy, are reported for pristine and functionalized CNT/epoxy composites. The CNT strain is derived from the difference in frequencies of the CNT vibrational G⁺-mode in the composite and that of a relaxed CNT, and shown to serve as a measure of the local residual strains in the composites. The magnitudes of these strains vary with both CNT functionalization and CNT concentration. At room temperature and with the same local concentration of CNTs in the composite, the strains of oxidized and polyamidoamine-functionalized CNTs are found to be 2.5 times higher than that of the composite containing pristine CNTs. The higher residual strain of the composites loaded with functionalized CNTs reflects their better adhesion and integration in the polymer matrix. These findings are in accordance with the improved tensile properties measured for the functionalized CNT composites.     

Effects of surface modification on rheological and mechanical properties of CNT/epoxy composites

Despite superior properties of carbon nanotubes (CNTs), physical properties of the CNT/epoxy composites are not improved significantly because interfacial bonding between the CNTs and the polymer matrix is weak. CNTs were treated by an acidic solution to remove impurities and modified subsequently by amine treatment or plasma oxidation to improve interfacial bonding and dispersion of nanotubes in the epoxy matrix. The functional groups on the surface of treated CNTs were investigated by X-ray photoelectron spectroscopy. The surface modified CNTs were embedded in the epoxy resin by ultra-sonication and the cured nanotube containing composites were characterized by field emission scanning electron microscopy. Rheological properties of nanotube containing epoxy resin and mechanical properties of the modified CNT/epoxy composites were improved because the modification of CNTs improved dispersion and interaction between the CNT and the epoxy resin.     

The sonication effect on CNT‐epoxy composites finally clarified

Carbon nanotube‐epoxy composites were prepared using amino‐functionalized CNTs and sonication as a mixing process. Different times and sonication powers were used for preparing composites in order to study how the sonication process may influence the curing reaction of both systems: neat epoxy resin and amino‐CNT/epoxy composite.The curing reaction was investigated with differential scanning calorimetry and the results were associated with analysis of gel permeation chromatography. The results showed that the effect of CNTs on the cure behavior of the epoxy resin depends on the sonication power. The sonication of neat resin with a 150 W powered device led to a molar mass reduction of the resin and an increase in the cure enthalpy. The CNT addition to this system reduced the cure enthalpy. However, when neat epoxy resin was sonicated with a 200 W powered device, the molar mass did not decrease (i.e., it was increased or was not changed) and the cure enthalpy did not increase (essentially it decreased or did not change). The CNT addition to such solutions did not reduce (i.e., it was increased or did not change) the cure enthalpy, which is a contrary result from that obtained with a 150 W powered device. POLYM. COMPOS., 38:1964–1973, 2017. © 2015 Society of Plastics Engineers     

Characterisation and modelling of CNT–epoxy and CNT–fibre–epoxy composites

Abstract

This research presents an experimental and theoretical investigation on the effects of carbon nanotube (CNT) integration within neat epoxy resin (nanocomposites) and a carbon fabric–epoxy composite (multiscale composites). An approach is presented for the prediction of mechanical properties of multiscale composites. This approach combines woven fibre micromechanics (MESOTEX) with the Mori-Tanaka model which was used for the prediction of mechanical properties of nanocomposites in this research. Nanocomposite and multiscale composite samples were manufactured using cast moulding, resin infusion, and hand lay-up process. The CNT concentrations in the composite samples were from 0 to 5 wt-%. The samples were characterised using tensile, shear and flexural tests. The discrepancy between the theoretical predictions and the experimental observations was hypothesised to be due to dispersion and bonding issues and SEM images are presented in support of the hypothesis.     

Multiscale fiber‐reinforced composites prepared by vacuum‐assisted resin transfer molding

Carbon nanotube (CNT)/aramid fiber epoxy composites were produced using a new manufacturing method proposed in this study. The rheological and morphological experiments of the CNT/PEO nanocomposites indicates that the PEO nanocomposites have a good dispersion state of the CNTs. The flexural mechanical properties of the aramid fiber/CNT epoxy composites were measured. The CNTs dispersed in the epoxy resin between the aramid fibers were observed using field emission scanning electron miscroscope (FESEM). It was found that the flexural properties of the multiscale fiber‐reinforced composites were higher than those of aramid fiber/epoxy composites. POLYM. COMPOS., 28:458–461, 2007. © 2007 Society of Plastics Engineers.     

Synthesis of carbon nanotube/epoxy composite films with a high nanotube loading by a mixed-curing-agent assisted layer-by-layer method and their electrical conductivity

A mixed-curing-agent assisted layer-by-layer method is reported to synthesize carbon nanotube (CNT)/epoxy composite films with a high CNT loading from ∼15 to ∼36 wt.%. The mixed-curing-agent consists of two types of agents, one of which is responsible for the partial initial curing at room temperature to avoid agglomeration of the CNTs, and the other for complete curing of epoxy resin at high temperature to synthesize epoxy composite films with good CNT dispersion. The electrical conductivity of the composites shows a value up to ∼12 S/m, which is much higher than that for CNT/epoxy composites with a low CNT loading prepared using conventional methods.     

Effect of deposited carbon nanotubes on interlaminar properties of carbon fiber‐reinforced epoxy composites using a developed spraying processing

Carbon fiber‐reinforced epoxy composites, with incorporated carboxylic multiwall carbon nanotubes (CNTs), were prepared using vacuum‐assisted resin infusion (VARI) molding, and the in‐plane and out‐of‐plane properties, including mode‐I (G_Ic) and mode‐II (G_IIc) interlaminar fracture toughness, interlaminar shear strength (ILSS), tensile, and flexural properties were measured. A novel spraying technique, which sprays a kind of epoxy resin E20 with high viscosity after spraying the CNTs, was adopted to deposit the CNTs on the surface of carbon fiber fabric. The E20 was used to anchor CNTs on the fabric surface, avoiding that the deposited CNTs were removed by the infusing resin during VARI process. The spraying processing, including spraying amount and spraying sequence, was optimized based on the distribution of CNTs on the fibers. After that, three composite specimen groups were fabricated using different carbon fiber fabrics, including as‐received, CNT‐deposited with E20, and CNT‐deposited without E20. The effects of CNTs on the processing quality and mechanical properties of carbon fiber‐reinforced polymer composites were studied. The experimental results show that all studied laminates have uniform thickness with designed values and no obvious defects form inside the laminates. Compared with the composite without CNTs, depositing CNTs with E20 increases by 24% in the average propagation G_Ic, by 11% in the propagation G_IIc and by 12% in the ILSS, while it preserves the in‐plane mechanical properties, However, depositing CNTs without E20 reduces interlaminar fracture toughness. These phenomena are attributed to the differences in the distribution of CNTs and the fiber/matrix interfacial bonding for different spraying processing. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Electrical and thermal conductivity and tensile and flexural properties of carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to insulating thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon nanotubes (CNTs) are very effective at increasing composite electrical conductivity at low loading levels without compromising composite tensile and flexural properties. In this study, varying amounts (2–8 wt %) of CNTs were added to polycarbonate (PC) by melt compounding, and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. The percolation threshold was less than 1.4 vol % CNT, likely because of CNTs high aspect ratio (1000). The addition of CNT to PC increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 6 wt % (4.2 vol %) CNT in PC resin had a good combination of properties for electrical conductivity applications. The electrical resistivity and thermal conductivity were 18 Ω‐cm and 0.28 W/m · K, respectively. The tensile modulus, ultimate tensile strength (UTS), and strain at UTS were 2.7 GPa, 56 MPa, and 2.8%, respectively. The flexural modulus, ultimate flexural strength, and strain at ultimate flexural strength were 3.6 GPa, 125 MPa, and 5.5%, respectively. Ductile tensile behavior is noted in pure PC and in samples containing up to 6 wt % CNT. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Investigation of CNT modification of epoxy resin in CFRP strengthening systems

The use of carbon fiber‐reinforced polymers (CFRPs) to reinforce old structures has become popular in recent years. In this study, the chemical structure of the epoxy resin used as the bonding agent in the CFRP strengthening system was modified by dispersing multi‐walled carbon nanotubes (MWCNTs) in order to improve the performance of the strengthening system. Composites were fabricated with different mixing orders employing the solvent‐assisted dispersion method and ultrasonic mixing. Thermogravimetric analysis, dynamic mechanical analysis, and tensile tests were conducted to investigate the effect of CNT dispersion and fabrication method on the thermal and mechanical properties of epoxy composite. In addition, the temperature‐dependent tensile behavior of fabricated composites was studied by performing tensile tests at elevated temperatures. The morphology of CNT/epoxy composites was characterized using scanning electron microscopy (SEM). Fourier transform infrared (FTIR) was also used to show the influence of solvent on the molecular structure of composites. Based on the experimental results, the decomposition temperature of the epoxy resin was heightened by 15°C as a result of solvent‐assisted dispersion of nanotubes. However, the glass transition temperature (T_g) was slightly reduced due to the solvent effect. FTIR analysis revealed that the solvent negatively affects the curing process of epoxy composite. A considerable enhancement was recorded in the tensile properties as a result of CNT infusion. This was attributed to the homogeneous dispersion of nanotubes which was shown by SEM images. Using solvent to disperse nanotubes led to the reduction of tensile strength of the epoxy composite at elevated temperature due to the lower T_g. POLYM. COMPOS. 37:1021–1033, 2016. © 2014 Society of Plastics Engineers     

Processing and failure behavior of carbon‐nanotube composites in sheet forms

In their original forms, carbon nanotubes (CNT) are spatially entangled. To make CNT papers (CNTPs), the CNT agglomerates must be dispersed and re‐entangled into a planar sheet. The processing characteristics are very different from those of traditional buck‐form nanocomposites. This article examines the processing, micro‐structures, and failure behavior of the CNTP composites. The CNTPs were first made by a dispersion and filtering process. Then, an epoxy resin was added into the CNTP by using a vacuum bag method. Different CNT weights were employed to make the CNTPs with different thicknesses and areal weights. The CNTP allows direct resin impregnation along the thickness direction and avoids the difficulty of dispersing CNTs in the viscous resin. The CNT content can be much higher than that attainable in traditional bulk CNT composites. Both tensile and tearing tests were conducted, and the fracture behaviors were examined. POLYM. COMPOS., 37:1564–1571, 2016. © 2014 Society of Plastics Engineers     

Resin film infusion: Toward structural composites with nanofillers

Resin Film Infusion (RFI) has been used to fabricate composites with continuous unidirectional E‐glass and epoxy with low weight fractions of carbon nanotubes (CNTs) in matrix. An ultrasound‐assisted dissolution‐evaporation method with thermoplastics or block copolymers as dispersing agents for nanoparticles enabled uniform dispersion of CNTs in the resin. Rheological characterization of CNT‐filled epoxy revealed that viscosity, and hence processing of the resin remains unaffected as compared to pristine resin at elevated temperatures of subsequent composite manufacturing. Local flow of the modified resin through the sandwiched fabric plies in RFI process as against the global flow in traditional liquid composite molding processes, made sure that uniform distribution of nanoparticles is accomplished throughout the composite. Compressive properties of hybrid composites improved considerably with CNTs at loading fractions as low as 0.2 wt %. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrophoretic deposition of carbon nanotubes onto carbon-fiber fabric for production of carbon/epoxy composites with improved mechanical properties

Carbon nanotubes (CNTs) have been deposited onto carbon-fiber fabric using electrophoretic deposition (EPD) prior to the infusion of epoxy resin for the production of carbon/epoxy composites. The carbon-fiber fabric employed for EPD was used in the as-received condition, in which the proprietary epoxy sizing-agent was present. CNTs were functionalized prior to EPD using ozone treatment for oxidation, followed by chemical reaction with polyethyleneimine. The CNT oxidation used a novel recirculating system which enabled ozonolysis to be conducted on large-volume solutions of CNTs in the presence of high-powered sonication, facilitating preparation of stable dispersions suitable for EPD. Significant increases in the shear strength and fracture toughness of the carbon/epoxy composites with the CNT treatment have been measured relative to composites without the CNT treatment. Analysis of fracture surfaces revealed interlaminar regions with high levels of CNTs and evidence of good adhesion between the carbon nanotubes and sized carbon-fiber, which is believed to have contributed to the measured improvement in mechanical properties.     

Barrier properties of thermal and electrical conductive hydrophobic multigraphitic/epoxy coatings

Epoxy composites doped with different content of graphene nanoplatelets (GNPs) and/or carbon nanotubes (CNTs) have been manufactured. Their chemical, thermal, electrical, and mechanical behaviors have been studied, evaluating also their performance as coatings of glass fiber composite substrates. It is confirmed that the graphitic nanofillers present different efficiency as nanofillers as a function of their geometry. CNTs are much higher efficient electrical nanofillers than graphene, but an important synergetic effect is determined in the electrical conductivity of hybrid GNP/CNT/epoxy composites. In contrast, the thermal conductivity scarcely depends on the geometry of graphitic nanofillers but on the graphitic nanofiller content. Adding up to 12 wt% GNP and 1 wt% CNT, the thermal conductivity of the epoxy resin can be increased more than 300%. GNP presents high efficiency to increase the barrier properties, reducing the water absorption up to 30%. The stiffness of nanocomposites proportionally increases with graphitic addition, up to 50%, regard to the modulus of the neat epoxy resin. The adherence of coatings over glass fiber composite substrates increases by nanofiller addition due to the nanomechanical anchoring. However, the water uptake induces a higher weakening on nanodoped composites due to the preferential water absorption by the interface.     

Synergistic strengthening by load transfer mechanism and grain refinement of CNT/Al–Cu composites

CNT/Al–Cu composites were fabricated by mixing of Al powders and CNT/Cu composite powders which were prepared by molecular level mixing process. The CNT/Al–Cu–Cu composites show a microstructure with a homogeneous dispersion of CNTs in the Al–Cu matrix and had a 3.8 times increase of yield strength and 30% increase of elastic modulus compared to Al–Cu matrix. The strengthening mechanism of CNT/Al–Cu composites was discussed by controlling the aspect ratio of CNTs and it was thought that the CNT/Al–Cu composites were strengthened by both load transfer from the Al matrix to the CNTs and dispersion strengthening of damaged short CNTs. At the same time, the addition of CNTs increases the grain refinement effect of the Al–Cu matrix which results in a grain size strengthening mechanism of the CNT/Al–Cu composites.     

Synthesis,morphology and physical properties of multi-walled carbon nanotube/biphenyl liquid crystalline epoxy composites

We have developed multi-walled carbon nanotube/liquid crystalline epoxy composites and studied the effects of incorporation carbon nanotubes (CNTs) on the morphology, thermal and mechanical properties of the composites. The CNTs are functionalized by liquid crystalline (LC) 4,4′-bis(2,3-epoxypropoxy) biphenyl (BP) epoxy resin for the ease of dispersion and the formation of long range ordered structure. The epoxy functionalized CNT (ef-CNT) were dispersed in the LC BP epoxy resin that can be thermal cured with an equivalent of 4,4′-diamino-diphenylsulfone to form composite. The curing process was monitored by polarized optical microscopy. The results indicate the LC resin was aligned along the CNTs to form fiber with dendritic structure initially then further on to obtain micro-sized spherical crystalline along with fibrous crystalline. With homogeneous dispersion and strong interaction between nanotubes and matrix, the composite containing 2.00 wt.% ef-CNT exhibits excellent thermal and mechanical properties. When the amount of ef-CNT exceeds 2.00 wt.%, vitrification stage of curing is fast reached, which lowers the degree of conversion. As compared with the neat resin, the composite containing 2.00 wt.% ef-CNT increases the glass transition temperature by 70.0 °C, the decomposition temperature by 13.8 °C, the storage modulus by 40.9%, and the microhardness by 63.3%.