Morphology and mechanical properties of PP/POE/nano‐CaCO3 composites

The mechanical properties including tensile, flexural, and impact of the nanometer on calcium carbonate (nano‐CaCO₃) filled polypropylene (PP)/poly (ethylene‐co‐octene) (POE) composites were measured at room temperature to identify the effects of the POE content on the mechanical properties. It was found that the Young's modulus, tensile strength, and tensile elongation at break decreased nonlinearly while the tensile fracture strength varied slightly with increasing the POE weight fraction; the V‐notched and unnotched Izod impact fracture strength increased nonlinearly with an increase of the POE weight fraction; the flexural modulus and strength decreased roughly linearly with increasing the POE weight fraction. Furthermore, the impact fracture surface of the specimens was observed by means of a scanning electronic microscope to discuss the toughening mechanisms. POLYM. COMPOS., 37:539–546, 2016. © 2014 Society of Plastics Engineers     

Biodegradable poly(lactic acid)/poly(butylene succinate)/wood flour composites: Physical and morphological properties

This work sought to improve the toughness and thermal stability of poly(lactic acid) (PLA) by incorporating poly(butylene succinate) (PBS) and wood flour (WF). The PLA/PBS blends showed a PBS‐dose‐dependent increase in the impact strength, elongation at break, degree of crystallinity, and thermal stability compared to the PLA, but the tensile strength, Young's modulus, and flexural strength were all decreased with increasing PBS content. Based on the optimum impact strength and elongation at break, the 70/30 (w/w) PLA/PBS blend was selected for preparing composites with five loadings of WF (5–30 phr). The impact strength, tensile strength, flexural strength, and thermal stability of the PLA/PBS/WF composites decreased with increasing WF content, and the degree of crystallinity was slightly increased compared to the 70/30 (w/w) PLA/PBS blend. Based on differential scanning calorimetry, the inclusion of PBS and WF into PLA did not significantly change the glass transition and melting temperatures of PLA in the PLA/PBS blends and PLA/PBS/WF composites. From the observed cold crystallization temperature of PLA in the samples, it was evident that the degree of crystallinity of PLA in all the blends and composites was higher than that of PLA. The PLA/PBS blend and PLA/PBS/WF composite degraded faster than PLA during three months in natural soil, which was due to the fast degradation rate of PBS. POLYM. COMPOS., 38:2841–2851, 2017. © 2016 Society of Plastics Engineers     

Zirconium nitride nano-particulate reinforced Alon composites: Fabrication, mechanical properties and toughening mechanisms

Aluminium oxynitride (Alon) exhibits excellent stability, high rigidity and good thermal shock resistance, but it has relatively low strength and poor fracture toughness. The aim of this investigation was to develop a new type of zirconium nitride (ZrN) nano-particulate reinforced Alon composites via a change of ZrO₂ nano-particles during sintering. A reduction of porosity and grain size was observed in the composite. With increasing amount of ZrN nano-particles up to 2.7%, the relative density, hardness, Young's modulus, flexural strength, and fracture toughness all increased. When the ZrN nano-particles exceeded 2.7%, while the flexural strength and fracture toughness decreased slightly, the density, hardness and Young's modulus continued to increase. Different toughening mechanisms including crack bridging, crack branching and crack deflection were observed, thus effectively increasing the crack propagation resistance and leading to a considerable improvement in the flexural strength and fracture toughness of the composites.     

玻璃微珠改性PP和LLDPE力学性能的比较研究

采用玻璃微珠(GB)改性聚丙烯(PP)和线性低密度聚乙烯(LLDPE)，对玻璃微珠的用量、粒径和复合材料加工方法对材料的力学性能的影响进行了比较研究。结果表明：随着GB用量的增加，单、双螺杆挤出GB／PP复合材料的拉伸模量、弯曲强度和弯曲模量均呈线性增长的趋势，而屈服强度则有小幅下降；断裂应变在低含量时有所提高，然后迅速下降；单双螺杆挤出材料的冲击强度均有所提高，并在一定范围内随GB用量的提高而增大，且单螺杆挤出材料的冲击强度略高于双螺杆挤出材料。而GB／LLDPE中，随着GB用量的增加，单螺杆挤出复合材料的拉伸模量、弯曲模量均呈线性增长趋势，而屈服强度和弯曲强度在含量较高时略有上升；双螺杆挤出复合材料的拉伸模量、屈服应力、弯曲强度和弯曲模量均呈线性增长的趋势，两者的断裂应变都有所降低，但没有严重劣化LLDPE复合材料的冲击特性。GB的粒径对两种复合材料的力学性能影响不大，但对GB／PP复合材料的韧性有较大影响。单、双螺杆挤出GB／PP复合材料的冲击强度在一定范围内较纯料有一定提高；同样的，双螺杆挤出复合材料的冲击强度低于单螺杆挤出材料。     

Mechanical and thermal properties of toughened polypropylene composites

The mechanical, thermal, and structural properties of a new flexible composite containing polypropylene fiber (PP) in a random poly(propylene‐co‐ethylene) (PPE) matrix with ethylene–propylene elastomer (EP) was investigated with emphasis on the effect of EP elastomer concentration. The intrinsic composition of the composites, toughening of the matrix with EP and the fiber–matrix interface determined the properties of the composites. Through the incorporation of EP elastomer into the polypropylene–poly (propylene‐co‐ethylene) (all‐PP) composite, tensile and storage modulus (E′) decreased, flexural modulus and loss modulus (E″, damping) increased slightly to 0.15 EP and then decreased. There was an increase in impact resistance for the toughened composites, with about 100% increase in comparison with an untoughened all‐PP composite. The composition corresponding to 0.20 weight fraction EP gave optimum impact and mechanical properties. Creep resistance of the composite decreased with increasing EP content, but recovery showed an increase with increasing EP content up to 0.20. Fracture surfaces of composites after impact tests were studied with scanning electron microscopy. Moreover, the use and limitation of theoretical equations to predict the tensile and flexural modulus of the flexible PP composite is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effects of mixing technique and filler content on physical properties of bovine bone‐based CHA/PLA composites

This study presented influence of mixing technique as well as filler content on physical and thermal properties of bovine bone‐based carbonated hydroxyapatite (CHA)/poly(lactic acid) (PLA) composites. CHA/PLA composites at various contents of CHA were prepared by either melt‐mixing or solution‐mixing techniques. Thermal properties, morphologies, and mechanical properties of the CHA/PLA composites including molecular weight deterioration of PLA matrices were investigated. Average molecular weights of PLA in the composites prepared by both techniques decreased with increasing CHA content, whereas their molecular weight distributions (MWDs) increased. Nonetheless, average molecular weights of PLA in melt‐mixed composites were lower than those of solution‐mixed composites. With increasing CHA content, elongation at break, tensile strength, and impact strength of the composites were decreased, whereas the tensile moduli of the composites were increased. In comparison between two mixing techniques, the melt‐mixing distributed and dispersed CHA into PLA matrix more effectively than the solution‐mixing did. Therefore, tensile moduli, tensile strength, and impact strength of the melt mixed composites were higher than those of the solution‐mixed composites of the corresponding CHA content. Moreover, decomposition temperatures and % crystallinity of the melt‐mixed composites were higher than those of the solution‐mixed composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Morphologies,crystallization, and mechanical properties of PLA-based nanocomposites: Synergistic effects of PEG/HNTs

In this study, the compounding modifier poly(ethylene glycol)/halloysite nanotubes (PEG/HNTs) was prepared by supersonic vibration and dynamic vacuuming. A series of poly(lactic acid) (PLA)/PEG and PLA/PEG/HNT composites were fabricated using a twin-screw extruder. Fourier transform infrared spectroscopy indicated that the hybrid between PEG and HNTs had no evident chemical interaction via supersonic vibration and dynamic vacuuming. The dispersed morphology of the compounding modifier in the PLA matrix was tested by high-resolution scanning electronic microscopy and transmission electron microscopy. The results showed that the low content of PEG/HNTs presented a good dispersion morphology. The binding energy of the PLA-based composites was studied through contact angle measurements. The results showed that PEG and PEG/HNTs can decrease the water contact angle of PLA, and that the binding energy between PEG and HNTs is higher than that of PLA/HNTs, which leads to more location of HNTs in the PEG phase. The crystallization behavior of PLA-based composites was examined by wide-angle X-ray diffraction and differential scanning calorimetry. The results suggested that the addition of PEG and PEG/HNTs effectively enhanced the crystallization of PLA and that the diffraction peak intensity of the PLA-based composites reached a maximum when the content of PEG/HNTs was 1.2 wt %. The spherulite morphology indicated that the addition of PEG resulted in perfect spherulites. The mechanical properties of PLA-based composites were analyzed with a universal testing machine and impact tester, which confirmed that the tensile strength and impact strength of the PLA-based composites increased slightly when the content of the PEG/HNT modifier was 1.2 wt %, while the tensile modulus of the PLA-based composites increased distinctly. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47385.     

阻燃型玻纤增强PA10T复合材料的热氧老化性能

采用溴化环氧树脂对聚对苯二甲酰葵二胺(PA10T)进行改性,并通过熔融共混法制备阻燃型玻璃纤维(GF)增强PA10T复合材料,采用人工加速热氧老化手段,研究了热氧老化对其力学性能的影响,并用扫描电子显微镜(SEM)对复合材料的冲击断面形貌进行观察。结果表明,随热氧老化时间增加,复合材料的拉伸强度、弯曲强度和缺口冲击强度均下降明显,分子链松弛过程减弱;老化10 d后,复合材料的弯曲弹性模量仅略有下降而储能模量达到最大值,表明在热氧老化初期PA10T分子链之间发生了微交联,但随老化时间继续增加,两者均下降明显。SEM结果表明GF与树脂基体之间界面粘接作用的强弱是影响材料热氧老化性能变化的主要因素。     

Improvement of the flame retardancy of plasticized poly(lactic acid) by means of phosphorus‐based flame retardant fillers

The aim of this study is to improve the flame resistance and toughness of poly(lactic acid) (PLA) with the addition of low amount of flame retardant fillers and plasticizer simultaneously. Poly(ethylene glycol) (PEG) was used as plasticizer for PLA. Ammonium polyphosphate, boron phosphate, and tri‐phenyl phosphate (TPP) were used as flame retardant additives. Among these flame retardant additives, boron phosphate was synthesized from its raw materials by using microwave heating technique. Characterization of PLA/PEG‐based flame retardant composites was performed by conducting tensile, impact, differential scanning calorimeter, thermal gravimetric analysis, scanning electron microscope, limiting oxygen index, and UL‐94 vertical burning tests. Mechanical tests showed that the highest tensile strength, impact strength, and elongation at break values were obtained with the addition of ammonium polyphosphate and TPP into PLA/PEG matrix, respectively. Scanning electron microscopy analysis of the composites exhibited that the more homogeneous filler distribution in the matrix was observed for TPP containing composite. The best flame retardancy performance was also provided by TPP when compared with the other flame retardant additives in the plasticized PLA‐based composites.     

Reinforcing and toughening on poly(ether imide) by a novel thermo tropic liquid crystalline poly(ester‐imide‐ketone) with low content

Reinforcing and toughening effects on the thermoplastic poly(ether imide) (PEI) by a novel thermo tropic liquid crystalline poly(ester‐imide‐ketone) (TLCPEIK) with low content were studied in this work. The novel TLCPEIK with kink naphthalene structure in the backbone was synthesized in our laboratory. A series of in‐situ composites (TLCPEIK/PEI) with a low concentration of TLCPEIK(≤5 wt%) were prepared by direct extrusion. Tensile strength, flexural strength, and flexural modulus of the composites increased with increasing TLCPEIK content. Impact strength and elongation at break of the composites were enhanced greatly when compared with that of pure PEI. To explain the simultaneously reinforcing and toughening effects on PEI by TLCPEIK, miscibility and morphology of the composites were studied by differential scanning calorimetry (DSC) and scanning electron microscopy. The experimental results suggest that good compatibility of the components is beneficial to improve the ultimate properties of TLCPEIK/PEI in‐situ composites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers.     

Poly(lactic acid)/ethylene vinyl acetate copolymer blend composites with wood flour and wollastonite: Physical properties,morphology, and biodegradability

In the present study, poly(lactic acid) (PLA), a biodegradable plastic, was melt‐blended with five weight percentages (10–50 wt%) of ethylene vinyl acetate (EVA) copolymer, a non‐biodegradable plastic, having a vinyl acetate content of 19 wt% and a melt flow index of 530 g/10 min, on a twin screw extruder, followed by an injection molding. The blends at 10 and 20 wt% EVA revealed a noticeably increased impact strength and strain at break over the pure PLA, and the blend at 10 wt% EVA exhibited the highest impact strength and strain at break. The 90/10 (wt%/wt%) PLA/EVA blend was then selected for preparing either single or hybrid composite with wood flour (WF) and wollastonite (WT). The filler loading was fixed at 30 parts by weight per hundred of resin throughout the experiment, and the WF/WT weight ratios were 30/0, 20/10, 15/15, 10/20, and 0/30. The prepared composites were examined for their mechanical and thermal properties, melt flow index, flammability, water uptake, and biodegradability as a function of composition. All the composites showed a filler‐dose‐dependent decrease in the impact strength and strain at break, but an increase in the tensile and flexural modulus (optimal at 0/30 WF/WT) and tensile and flexural strength (optimal at 30/0 WF/WT) as compared with the neat 90/10 (wt%/wt%) PLA/EVA blend. In addition, the melt flow index, char residue, anti‐dripping ability, water uptake, and biodegradability of the composites were also higher than those of the neat blend. J. VINYL ADDIT. TECHNOL., 25:313–327, 2019. © 2019 Society of Plastics Engineers     

Mica reinforced nylon‐6: Effect of coupling agents on mechanical,thermal, and dielectric properties

The effects of applying titanate (TYZOR® TPT) and silane (DYNASYLAN VTMO) coupling agents to wet ground muscovite mica in nylon‐6 composites are described. Nylon‐6 composites of 5–40 wt % filler loadings were compounded using an APV Baker twin‐screw extruder. Mica (25 wt %) brought about an increase in the Young's modulus, flexural strength, and flexural modulus but did not produce significant variations in tensile and impact strength. Hence different coupling agents were employed. It was observed that titanate coupling agent improved the tensile strength and the Young's modulus of the composites much while the impact properties were enhanced by the silane coupling agent. An attempt was made to use ?‐caprolactum in improving the interfacial adhesion of the filler and the matrix. It was observed that ?‐caprolactum improved the flexural modulus of the composites most. The effect of coupling agents on the dielectric strength, heat distortion temperature, and morphology were also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4074–4081, 2006     

茶粉/聚乳酸复合材料的增韧改性

为高值化利用茶产业剩余物资源,以茶粉（TD）为生物质填料,聚乳酸（PLA）为基体,以甘油（GL）、聚乙二醇400（PEG400）、环氧大豆油（ESO）和乙酰柠檬酸丁酯（ATBC）为增塑剂,制备了可降解TD/PLA增韧复合材料,并采用红外吸收光谱、热重分析、转矩流变仪、扫描电镜及力学性能测试等考察了增塑剂对TD/PLA复合材料结构与性能的影响。结果表明：4种增塑剂都可改善TD/PLA复合材料的加工流变性,GL的添加不利于复合材料韧性,PEG、ATBC及ESO的添加提高了复合材料韧性,其中ESO增韧效果最佳,其添加制备的复合材料断裂伸长率及缺口冲击强度分别提高了154.23%和65.53%,GL增韧效果最差,ATBC增韧后复合材料力学强度和模量最高。FTIR分析表明,ATBC和ESO可与PLA发生一定相互作用,使C-O键红外吸收峰位增大,其增韧后复合材料吸水率下降。ESO添加提高了TD/PLA复合材料的维卡软化点和热稳定性。SEM图片显示,TD/PLA/ESO复合材料断面粗糙,ESO分散较均匀,与PLA部分相容,而TD/PLA/GL复合材料断面出现严重相分离结构。该研究结果可为进一步探索聚乳酸基茶塑复合材料制备及应用提供试验数据和理论参考。     

Binary and ternary particulated composites: UHMWPE/CACO3/HDPE

A study of the influence of employing ultrahigh molecular weight polyethylene (UHMWPE) on the toughness of CaCO₃/high‐density polyethylene (HDPE) composites was carried out. Binary and ternary HDPE‐based composites with calcium carbonate in the range of 0–40% and UHMWPE in the range of 0–50% were produced by twin‐screw extrusion followed by compression molding. From tensile and impact tests, it was found that increasing calcium carbonate content increased tensile modulus, but decreased tensile strength, strain at break, and impact resistance. The addition of UHMWPE helped to increase the strain at break and impact resistance of composites moderately without decreasing modulus or strength. The degree of toughening was found to increase with increasing UHMWPE content, but to decrease as the filler volume fraction was increased. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1503–1513, 2000     

Simultaneous full‐interpenetrating polymer networks of blocked polyurethane and vinyl ester. II. Static and dynamic mechanical properties

Simultaneous full‐interpenetrating polymer networks (full‐IPNs) based on blocked polyurethane (PU) and vinyl ester (VE) have been prepared. The static and dynamic properties of these IPNs have been examined. Results show that the tensile strength and flexural strength of IPNs increased with blocked PU content to a maximum value at 7.5 wt % PU content and then decreased. The tensile modulus, flexural modulus, and hardness of IPNs decreased with increasing blocked PU content. The impact strength of IPNs increased with increasing blocked PU content. The tensile strength, flexural strength, tensile modulus, and flexural modulus of IPNs increased with filler (kaolin) content to a maximum value at 20 to 25 phr filler content and then decreased. The higher the filler content, the greater the hardness, and the lower the impact strength of IPNs. The tensile strength, flexural strength, tensile modulus, flexural modulus, and hardness of IPNs increased with increasing VE initiator content. The dynamic technique was used to determined the damping behavior across a temperature range. Results show that the glass transition temperature (T_g) of IPNs are shifted inwardly compared with pure PU and VE, which indicated that the blocked PU–VE IPNs showed excellent compatible. Meanwhile, the glass transition temperature was shifted to a higher temperature with increased filler content. The dynamic storage modulus (E′) of IPNs increased with increasing VE and filler content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1977–1985, 1999     

Toughening of polylactide via in situ formation of polyurethane crosslinked elastomer during reactive blending

Polylactide (PLA)/polyurethane (PU) composites were prepared by reactive blending method with in situ formation of PU particles via the reaction between polyester polyol (PPG) and toluene‐2,4‐diisocyanate (TDI). The interfacial compatibility and adhesion between the PLA and PU phases were greatly improved by the reaction of the terminal hydroxyl groups of PLA and N?C?O groups of TDI forming graft copolymer, as confirmed by FTIR spectroscopy. The elongation at break and notch impact strength of PLA/PU composites increased considerably with increasing PU content, and the tensile strength of PLA/PU composites decreased slightly compared with that of pure PLA. Upon addition of 12 wt % PU, the elongation at break and notch impact strength increased to 175.17% and 10.96 kJ/m², respectively, about 27 times and 5.4 times greater than the corresponding values for the pure PLA. The tensile strength decreased only slightly to 48.65 MPa. The excellent interfacial adhesion, the dispersed PU elastomeric particles acting as stress concentration areas, and the triggering of large matrix shear yield as well as many fibrils by internal cavitation were the main mechanical toughening mechanisms. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44383.     

Flexural and Charpy impact behaviour of epoxy/glass fabric treated by nano-SiO2 and silane blend

A sizing formulation, containing compatible and incompatible silane coupling agents with epoxy resin in conjunction with nanoscale colloidal silica, was used to modify the surface of glass fabric. The modified glass fabric/epoxy resin composite panels were fabricated and characterised by flexural test, Charpy impact test and scanning electron microscope (SEM). By combining nano silica with silane blend in the fabric sizing, more energy was consumed under bending and impacting, which resulted in an improvement of the toughness in composites. The flexural strength, bending stain and Charpy impact strength of the epoxy composite/glass fabric treated with 1?wt-% nano silica and silane blend were ～42, ～22 and 35%, respectively, higher than those of silane blend coated glass fabric-reinforced composites (without nano silica). Furthermore, the change of the brittle fracture of the composite into ductile fracture was investigated by SEM micrographs. A possible toughening mechanism was also proposed.     

Biocomposites Made from Short Abaca Fiber and Biodegradable Polyesters

Natural fiber‐reinforced biodegradable polyester composites were prepared from biodegradable polyesters and surface‐untreated or ‐treated abaca fibers (length ca. 5 mm) by melt mixing and subsequent injection molding. Poly(butylene succinate)(PBS), polyestercarbonate (PEC)/poly(lactic acid)(PLA) blend, and PLA were used as biodegradable polyesters. Esterifications using acetic anhydride and butyric anhydride, alkali treatment, and cyanoethylation were performed as surface treatments on the fiber. The flexural moduli of all the fiber‐reinforced composites increased with fiber content. The effect of the surface treatment on the flexural modulus of the fiber‐reinforced composites was not so pronounced. The flexural strength of PBS composites increased with fiber content, and esterification of the fiber by butyric anhydride gave the best result. For the PEC/PLA composites, flexural strength increased slightly with increased fiber content (0–20 wt.‐%) in the case of using untreated fiber, while it increased considerably in the case of using the fiber esterified by butyric anhydride. For the PLA composite, flexural strength did not increase with the fiber reinforcement. The result of soil‐burial tests showed that the composites using untreated fiber have a higher weight loss than both the neat resin and the composites made using acetylated fiber.

Flexural modulus of PBS composites as a function of fiber content.     

Mechanical and thermal properties of polypropylene/sugarcane Bagasse composites

To determine the possibility of using sugarcane bagasse (SCB) waste as reinforcing filler in the thermoplastic polymer matrix, SCB‐reinforced polypropylene (PP) composites were prepared. The PP and SCB composites were prepared by the extrusion of PP resin with 5, 10, 15, and 20 wt % of SCB filler in a corotating twin screw extruder. The extruded strands were cut into pellets and injection molded to make test specimens. These specimens were tested for physicomechanical properties such as tensile, flexural, Izod, and Charpy impact strengths, density, water absorption, and thermal characteristics, namely, heat deflection temperature (HDT), melt flow index, and thermogravimetric analysis. It was found that the flexural strength increased from 23.66 to 26.84 MPa, Izod impact strength increased from 10.499 to 13.23 Kg cm/cm, Charpy impact strength increased from 10.096 to 13.98 Kg cm/cm, and HDT increased from 45.5 to 66.5°C, with increase in filler loading from 5 to 20% in the PP matrix. However, the tensile strength and elongation decreased from 32.22 to 27.21 MPa and 164.4 to 11.20% respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3827–3832, 2007     

The comparison of properties of (rubber tree seed shell flour)‐filled polypropylene and high‐density polyethylene composites

The effect of varied rubber tree seed shell flour (RSSF) filler loadings on processing torque, mechanical, thermal, water absorption, and morphological properties of polypropylene (PP) and high‐density polyethylene (HDPE) composites has been studied. The addition of RSSF in the composites increased the stabilization torque in both PP‐ and HDPE‐based composites. Tensile strength, elongation at break, flexural strength, and impact strength show significant reduction when higher loading of RSSF was incorporated, while tensile modulus and flexural modulus were improved. The phenomenon was noted for both matrices, PP and HDPE, but HDPE‐based composites showed clear effects on the reduction of the mechanical properties compared with RSSF‐filled PP. Scanning electron microscopy of tensile fracture specimens revealed the degree of dispersion of RSSF filler in the matrices. At higher filler loadings, agglomerations and poor dispersion of RSSF particles were spotted, which induce the debonding mechanism of the system. Thermogravimetric analysis thermograms showed that both PP‐ and HDPE‐based composite systems with higher RSSF content have higher thermal stability, initial degradation temperature, degradation temperature, and total weight loss. Water absorption ability of the composites increases as the filler loading increases for both matrices. J. VINYL ADDIT. TECHNOL., 22:91–99, 2016. © 2014 Society of Plastics Engineers