The stress-strain behavior of materials exhibiting andrade creep

The stress-strain behavior of a material exhibiting Andrade creep (for which the creep compliance is linear in the cube-root of time) has been calculated for loading at constant strain rate \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop {\rm \varepsilon}\limits^{\rm .} $\end{document} and at constant stress rate \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \sigma \limits^. $\end{document} for the limiting case of linear viscoelastic behavior and at constant \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \sigma \limits^. $\end{document} for one type of nonlinear viscoelastic response. The recoverable strain after the stress has been removed has also been calculated for these three cases. The results of the calculations are compared with experiment.     

Elongational behavior of short glass fiber reinforced polypropylene melts

The Rheometrics Elongational Rheometer was employed to study the uniaxial extensional flow of glass fiber filled polypropylene melts, in which the fiber concentration, c, varied between zero and 40 weight percent. The constant strain rate mode was used for strain rates, \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \varepsilon \limits^. $\end{document}, between 0.003 and 0.6 s⁻¹. Steady state elongational viscosities were observed in most cases for fiber filled polypropylene melts, even at rates at which the stress continued to increase for unfilled polypropylene. The rate of relative stress growth increased with \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \varepsilon \limits^. $\end{document} and was affected by the addition of fibers. The steady elongational viscosity of the fiber reinforced melts was found to decrease with increasing \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \varepsilon \limits^. $\end{document} and to increase with increasing c. Yield stresses were observed in elongational flow at high concentrations, although there was no clear evidence of yield in steady shear.     

Elongational flow studies of hinged rodlike molecules

Poly(amino acid) in an intermediate state of its helix-coil transition is known to be in a hinged rodlike conformation. In this work, the responses of poly(amino acids) in the hinged rodlike conformation against an elongational flow field were investigated by monitoring their flow-induced birefringence. Poly(L-glutamic acids) (PGA) and poly(γ-benzyl-L-glutamate) (PBLG) were examined as polyelectrolyte and noncharged poly(amino acids), respectively, and the results were compared. In the plots of flow-induced birefringence, Δn, against strain rate, $ {\dot \varepsilon } $, for hinged rodlike PBLG, there was a critical strain rate, $ \dot \varepsilon_0 $, below which Δn was not observed. Over $ \dot \varepsilon_0 $, the birefringence pattern observed was identical with that of rodlike molecules. The Δn vs. $ {\dot \varepsilon } $ plot for hinged rodlike PGA had characteristics of a rigid rod at any strain rate and there was no $ \dot \varepsilon_0$ observed. The rotational diffusion coefficient, D_r, of PBLG in the hinged rodlike conformation was larger than that for its helical conformation, while D_r, for the hinged-rodlike PGA was smaller than that for its helical conformation. It is concluded that the hinged-rodlike PGA molecule is in an extended form and that the hinged-rodlike PBLG is hydrodynamically more compact and rigid than that in its quiescent state. It is deduced that at $\dot \varepsilon_0$ hinged rodlike PBLG molecules collapse to a conformation optically anisotropic and mechanically rigid. © 1996 John Wiley & Sons, Inc.     

Shear rate dependence of the viscosity of cellulose nitrate solutions in the dilute concentration regime revisited

A detailed rheological study of cellulose nitrate in ethylacetate had been carried out in the dilute concentration (c) regime, covering a degree of polymerization (DP) range between 300 < DP_η < 7000 and shear rates ($ \dot \gamma $) between 100 s^?1 < $ \dot \gamma $ < 2000 s^?1. The results show a strong dependence of the transition Newtonian to non-Newtonian behavior on the three variables $ \dot \gamma $, DP, and c, similar to that found recently on solutions of synthetic polymers. Emphasis has been put on the critical concentrations corresponding to the standard shear rate 1000 s^?1 to correspond to the standard conditions ($ \dot \gamma $ ? 1000 s^?1; 0.3 < [η] · c < 0.6; DS = 2.90 ± 0.02) proposed for the determination of the intrinsic viscosity [η] of cellulose nitrates. It is shown that solutions with concentrations adjusted according to the above given conditions still exhibit Newtonian behavior, up to the highest range of DP. It follows, therefore, that applying the standard conditions, an extrapolation to $ \dot \gamma $ = 0 as has been proposed often for the intrinsic viscosity determination of cellulose nitrate is not advisable and results in considerable error. Considering the relationship between [η] and DP, the present results indicate that the decrease of the exponent ( a ) from a = 1.0 to a = 0.76, taking place above a DP ? 1000, is not a consequence of the applied shear rate but rather of the molecular properties of the solutes themselves.     

Viscosity of bead suspensions in polymeric solutions

Viscosity measurements made by a cone-plate viscometer on polyisobutylene in decalin solutions at different concentrations and their corresponding glass bead suspensions with filler loadings up to 40% by volume are reported. The range of shear rate $ \dot \gamma $ investigated is between 0.1 and 1000 sec^?1. The solutions show shear-thinning behavior, and the relative viscosity η_r of the slurries generally decreases with increasing shear rate. The results indicate two different types of mechanism, respectively at high and low shear rates. At low $ \dot \gamma $, the relative viscosity can be correlated extending relations already well known for suspensions in Newtonian liquids which are based on the mechanism of aggregate disruption. The behavior at high $ \dot \gamma $ values is believed to be due to the influence of the filler on the flow properties of macromolecules, in particular on relaxation time. Through a shifting procedure, an increase in relaxation time which depends on filler content and not on polymer concentration is shown.     

Stress relaxation behaviour of liquid crystalline solutions of ethyl celluloses with different molecular weight in m-cresol

The stress relaxation behaviour of liquid crystal-forming ethyl celllulose (EC) solutions in m-cresol was determined by means of a cone-plate type viscometer at 30°C. The effect of molecular weight (MW) on the behaviour was also determined. The relaxation behaviour could be fitted with the following equation: where σ_i and σ_f are steady-state shear stresses at shear rate $\dot \gamma _{\rm i}$ and $\dot \gamma _{\rm f}$, σ(t) is time- dependent stress, A₁ and A₂ are constants, τ₁ and τ₂ are relaxation times, t is time, and t_c is a characteristic time. When log σ* was plotted against time, one straight line was obtained for isotropic solutions, whereas anisotropic solutions yielded two straight lines. This suggests that the liquid crystalline solutions have two separate relaxation processes: Process 1 has a relatively short relaxation time, and process 2 has a long one. The parameters τ₁, τ₂, and A₂ were greatly dependent on polymer concentration, combination of $\dot \gamma _{\rm i}$ and $\dot \gamma _{\rm f}$, and MW, whereas A₁ was independent thereof and was close to unity. The process 1 was supposed to be valid for individual molecules, and process 2 for liquid crystalline domains or randomly aggregated or entangled molecules.     

A microscopy study of the transition from yielding to crazing in polypropylene

The deformation mechanisms in polypropylene as a function of strain rate have been studied by scanning electron microscopy. Injection molded, dogbone specimens were tested in tension at a temperature of 50°C and strain rates from 10^?4 to 90 s^?1. With increasing strain rate a gradual transition from cold drawing and necking to nearly homogeneous deformation was observed. The transition is characterized by a strong elastic recoil after fracture. At $ {\rm \dot \varepsilon } $ = 90 s^?1, the elastic recovery has its maximum value of 70% of the strain at break (ε = 0.3). The morphology was studied post mortem at small strains outside the neck using permanganically etched samples. The transition in the macroscopic behavior was found to coincide with a change in the deformation mechanism. Whereas yielding is the dominant mechanism at low strain rates, homogeneous voiding is found at $ {\rm \dot \varepsilon } $ = 90 s^?1. A correlation is suggested between the failure of chain slip within the lamellae and the occurrence of voiding, leading to distinct voiding patterns in the spherulites.     

A corresponding states treatment of saturated density,surface tension and capillary constant of cryogenic liquids and refrigerants

Using a new set of energy (kT) and length (σ) parameters, a corresponding states treatment is applied to the calculation of some thermophysical properties in a generalised non-dimensional form. The saturated density is well represented by the following equation: for all the liquids studied here. The surface tension correlations are $ \gamma _r^* = 2.055\left({1.219 - T_r^*} \right)^{1.240} $ for cryogenic fluids and hydrocarbons and $ \gamma _r^* = 2.322\left({1.228 - T_r^* } \right)^{1.244}$ for refrigerants. An interpretation of the index in the density equation and the constants in the surface tension equations is given. Using these correlations, an equation is also proposed for the capillary constant.     

Polymer melt elongation—methods,results, and recent developments

For film blowing of polyethylene it has been shown previously that melt elongation is very powerful for polymer characterization. With two types of rheometers, simple (also called “uniaxial”) elongational tests as well as creep tests can be performed homogeneously. In simple elongation, the melts of branched polyethylene show a remarkable strain hardening. With respect to their advantages and disadvantages, these rheometers complement each other. For multiaxial elongations the various modes of deformation can be performed by means of the rotary clamp technique. With the strain rate components ordered such that \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}₁₁ ? \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}₂₂ ≥ \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}₃₃, the ratio m = \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}₂₂/\documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}₁₁ characterizes the test mode. The Stephenson definition of the elongational viscosities makes use of the linear viscoelastic material equation and proves to be very efficient because the linear shear viscosity (t) (“stressing” viscosity) can act as the reference for the nonlinear behavior in elongation. Results are given for polyisobutylene measured not only in simple, equibiaxial, and planar elongations, but also in new test modes with a change of m during the deformation. This allows one to investigate the consequences of a deformation-induced anisotropy of the rheological behavior.     

Effect of shear rate on solution polymerization of acrylonitrile

Application of shear is found to increase the rate of solution polymerization of acrylonitrile in N,N-dimethyl formamide (DMF) initiated by benzoyl peroxide by as much as 400 percent of the value in absence of shear. The solvent DMF acts as an inert and maintains a homogeneous reaction mass during the entire course of polymerization. To study the effect of shear systematically, a special dilatometer has been constructed such that a constant shear rate, \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \gamma \limits^. $\end{document} could be applied to the reaction mass. The rule of solution polymerization has been measured under the variation of \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \gamma \limits^. $\end{document} and monomer concentration in the system. The measurements of induction time on the addition of a strong inhibitor, hydroquinone, reveal that the increase in the rate of polymerization with shear rate can be largely attributed to the change in the initiator efficiency. As a further confirmation of the above hypothesis, the decomposition of benzoyl peroxide in nitrobenzene at 80°C was measured and was found to increase significantly on application of shear. This confirms the importance of mass-transfer resistance in removal of CO₂, and the increase in the rate of polymerization of acrylonitrile occurs because the decomposition of benzoyloxy radicals is favored in the forward direction. Since the polymerization of acrylonitrile is preferentially initiated by phenyl radicals, the rate of polymerization is found to increase.     

Preparation,structure, and properties of two-phase co-continuous polymer blends

Phase continuity has been explored as a function of composition for three two-phase polymer blends produced by mixing in the melt: polystyrene/poly(methyl methacrylate), polystyrene/cis-polybutadiene, and poly(methyl methacrylate)/ethylene-propylene rubber. The condition for dual phase continuity Is the application of shear close to phase inversion and this can be predicted fairly accurately using the relation where 1 and 2 are the blend components, η is viscosity, \documentclass{article}\pagestyle{empty}\begin{document}$\mathop \gamma \limits^.$\end{document} is the shear rate in the mixing device used to produce the blend and ? is volume fraction. The co-continuous materials, which we call Interpenetrating polymer blends (IPBs) are non-equilibrium structures and are subject to disruption by changes in flow regime.     

Plasma polymerization of organoisothiocyanates. II. Structure of polymer film

Methyl-, n-propyl-, allyl-, and phenyl isothiocyanates (MITC, PITC, AITC, and PHITC respectively) were polymerized in an RF (13.56 MHz) plasma electrodeless flow system. The plasma produced polymers were characterized using IR, GPC, GC/MS, and direct pyrolysis mass spectrometry (DPMS) techniques. The solubility tests and chromatographic examinations of the polymers revealed a small soluble fraction which contained a mixture of oligomers with a predominance of dimers and trimers. Molecular structure of the components of these fractions, identified by GC/MS, suggests fragmentation of the monomers to reactive fragments: $$ ^ \cdot {\rm RSCN},^ \cdot {\rm RCN},{\rm R}^ \cdot ,^ \cdot {\rm CN} $$ (in the case of MITC, PITC, AITC) and $ ^ \cdot {\rm ArNCS},{\rm PhS}^ \cdot ,{\rm Ph}^ \cdot ,^ \cdot {\rm CN} $ (in the case of PHITC). The DPMS data, being generally consistent with IR and GS/MS results, proved the presence in the polymers of sulfide, polysulfide, thiocarbonyl (–CS–S–and–S–CS–S–) groups, and molecular sulfur S₈. Elementary plasma reactions involved in the formation of the observed structural units are proposed.     

Empirical correlation of flow properties of poly(vinyl chloride)

Empirical correlations of flow properties of poly(vinyl chloride) were made using data reported by a number of investigators. Correlation was made by plotting the reduced variable viscosity η/η₀ versus \documentclass{article}\pagestyle{empty}\begin{document}$ (\eta _0 \dot \gamma \bar M_w )/(_\rho RT) $\end{document} or \documentclass{article}\pagestyle{empty}\begin{document}$ (\eta _0 \dot \gamma \bar M_w ^{0.5} )/(_\rho RT) $\end{document} for unplasticized PVC and versus \documentclass{article}\pagestyle{empty}\begin{document}$ (\eta _0 \dot \gamma \bar M_w ^{0.5} )/(_\rho RTW_2 ^a ) $\end{document} with polymer concentration, W₂, for PVC containing plasticizer.     

Characterization of polyvinyl chloride part II. The unperturbed end to end distance values obtained from a new GPC method and viscometry

A new gel permeation chromatography (GPC) method is proposed for determining the unperturbed end-to-end distance, \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{r_0 ^2 }}{M}} \right)^{0.5} $\end{document}, of polymers of known molecular weights, Mn and Mw. This method requires the value of \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{r_0 ^2 }}{M}} \right)^{0.5} _{{\rm ps}} $\end{document} of polystyrene which was determined through viscometry to be 0.735 \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{{\rm {\AA}}^2-{\rm mole}}}{{gm}}} \right)^{0.5} $\end{document} Polyvinyl chloride (PVC) was chosen to illustrate the method and \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{r_0 ^2}}{M}} \right)^{0.5} _{pvc} $\end{document} was found to be 0.99 from GPC data which is in agreement with the result obtained from viscometry, \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{r_0 ^2}}{M}} \right)^{0.5} _{pvc} $\end{document} = 1.01. All \documentclass{article}\pagestyle{empty}\begin{document}$ \left({\frac{{r_0 ^2 }}{M}} \right)^{0.5} $\end{document} values were determined at 30°C. The advantage to this method lies in its speed and economy of materials.     

Die Wahl des optimalen Verfahrens für die Bestimmung des Primärradikalabbruchs aus Geschwindigkeitsdaten

The various plots for estimating the ratio of rate constants characteristic for primary radical termination, k₅/k₁k₂, have been examined systematically. Apart from the special case d ≡ k₃k₆/k₅² = 1 there is no exact linear relationship between the general quantity \documentclass{article}\pagestyle{empty}\begin{document}${\rm Y \equiv (\sqrt {c_S} c_{M}/v_{Br})^{n}}$\end{document} and the general variable \documentclass{article}\pagestyle{empty}\begin{document}${\rm X \equiv (\sqrt {c_S} /c_M)^{s} (v_{Br}/c_M^{2} )^{1 - s}}$\end{document}. In any case, however, Y can he expressed as a power series of X. Therefore the best way to obtain the most favourable linear representation of Y as a function of X is to choose s and n according to the condition that the coefficient of the term quadratic in X has to disappear (n ? 2 s + d = 0) and the coefficient of the X³-term also equals 0 or is at least close to 0. Under these conditions even those data can be represented in an almost perfect linear form which show variations of the quantity \documentclass{article}\pagestyle{empty}\begin{document}$({\rm \sqrt{c_{s}}c_{M}/v_{Br})}$\end{document} by a factor of \documentclass{article}\pagestyle{empty}\begin{document}$\sqrt{2}$\end{document} or more for different initiator concentrations c_s. If additionally allowance is made for the consumption of monomer by the initiation process the desired ratio of rate constants, k_s/k₁k₂, is obtained from the plot of Y vs. X according to the equation The application of this method is illustrated using an example from literature.     

Effect of matrix's type on the dynamic properties for short fiber-elastomer composite

The dynamic moduli, E′ and E″, and tan δ for PET–CR, PET–EPDM, and PET–UR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed three peaks for PET–elastomer composites. The peaks at the low temperature corresponded to the main dispersion of the respective matrixes and the peak at about 140°C to the α-dispersion of PET fiber. A small and broad peak observed at a temperature between 60 and 120°C may be caused by the relaxation of the interface region between fibers and matrix. The longitudinal storage modulus for the composite E was given by the parallel model as \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm E'}_\parallel = V_f \cdot E'_f + V_m \cdot E'_m $\end{document}, where E and E are the storage moduli for fiber and matrix and V_f and V_m are the volume fraction of fiber and matrix, respectively. In the transverse direction of fibers, the composite modulus E was expressed by the logarithmic law of mixing as follows: \documentclass{article}\pagestyle{empty}\begin{document}$ \log E'_ \bot = V_f \cdot \log E'_f + V_m \cdot \log E'_m $\end{document}. The peak values of tan δ from the main dispersion of the respective matrixes were given by the equation, (tan δ_⊥max)_c/(tan δ_max)_m 1 ? β · V_f, where (tan δ_⊥max)_c and (tan δ_max)_m are the maximum values of the loss tangent for the composite and matrix, respectively, and β is coefficient depending on matrix's type. The β value of PET–CR composite is the largest one among those of the composites.     

Melt rheology and extrudability of polyethylenes

Commercial high density polyethylene (HDPE), low density polythylene (LDPE), and linear low density polyethylene (LLDPE) resins were tested at 150, 170, and 190°C in steady state, dynamic, and extensional modes. Within the low rates of deformation \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \gamma $\end{document} = ω ≤ 0.3, the steady state and dynamic functions agreed: η = η′ and N₁ = 2G′; at the higher rates, the steady state parameters were larger. The elongational viscosity, η_e, was measured under a constant rate, \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon $\end{document}, or stress, σ, condition. In the first case for LLDPE, the transient η reached an equilibrium plateau value, η_e. For HDPE, η increased up to the break point. For LDPE, stress hardening was recorded. Under constant stress the η_e, could always be determined; its value, within experimental error, agreed with the maximum value of η determined in a constant \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon$ \end{document} experiment. The maximum strain at break was only ε = 1.5 for HDPE and 3, to 4 for LDPE and LLDPE. The rate of deformation dependence of the η (or η′) and η_n may be discussed in terms of the Trouton ratio, R_T = η_e/3η at \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \gamma $\end{document} = ω = \documentclass{article}\pagestyle{empty}\begin{document}$ \dot \varepsilon$ \end{document}: R_T ≤ 1.2 for LLDPE, R_T ≤ 2.5 for HDPE, and R_T ≤ 15 for LDPE. The PE resins were extruded at 190°C through a laboratory extruder equipped with a slit or rod die. The rotational speed of the screw varied from 0 to 90 rpm. Extrusion pressure, output, and energy were measured and correlated with the rheological parameters of the resins.     

A model relating the elastic properties of high-density polyethylene melts to the molecular weight distribution

An earlier model relating the variation of the steady-shear melt viscosity of high-density polyethylene to the molecular weight distribution is applied toward predicting the steady-shear elastic compliance, the first normal stress difference, and relaxation spectrum as a function of shear rate from the molecular weight distribution. The model envisions the cutting off of longer relaxation times as the shear rate is raised such that at any shear rate ${\rm \dot \gamma }$ the molecular weights and their corresponding maximum relaxation times τ_m are partitioned into two classes; the relaxation times are partitioned into operative and inoperative states, depending on whether they are less than or greater than τ_c, the maximum relaxation time allowed at ${\rm \dot \gamma }$. Equations relating molecular weight and relaxation time to the steady-shear elastic compliance and viscosity are assumed valid at nonzero shear rates, except for the partitioning effect of shear rate. The shear rate dependence of the first normal stress difference and the steady-shear viscosity for polyethylene melts is successfully predicted over the range covered by the cone-and-plate viscometer. The assumed proportionality constant between τ_c and 1/${\rm \dot \gamma }$ was determined to be 1.7. Using this relation, the maximum relaxation time at 190°C for a polyethylene molecule of molecular weight M is given by τ_m = 1.4 × 10^?19 (M)^3.33. Reasonable agreement has been obtained between the experimentally determined relaxation spectrum of a polyethylene melt and that predicted from the molecular weight distribution. The agreement is best at the longest relaxation times.     

Dynamic stress intensity factors during viscoelastic crack propagation at various strain rates

Dynamic stress intensity factors K_D were measured by the caustic method and crack propagation velocity ? by the velocity gauge techniques for PMMA [poly(methyl methacrylate)] during dynamic crack propagation at various strain rates \documentclass{article}\pagestyle{empty}\begin{document}$ \rm \dot \varepsilon $\end{document} . No definite applied strain rate effects on the dynamic stress intensity factor were observed for applied strain rates ranging from 8.33 × 10^?4 to 30/sec; however, the test results do show crack propagation velocity dependency in K_D ～ ? relations. The high local strain rate region may be realized at the running crack tip even under the quasi-static loading case of \documentclass{article}\pagestyle{empty}\begin{document}$ \rm \dot \varepsilon $\end{document} = 8.33 × 10^?4/sec, since all the crack propagation velocities obtained were greater than 50 m/sec even up to 450 m/sec.     

Relation between kneading behavior and flow instability of a high molecular weight high density polyethylene,applications to extrusion

Non-monotonic continuous curves of torque as a function of shaft speed, M(N), have been obtained for a high molecular weight high density polyethylene (HDPE) from measurements obtained with a torque rheometer (Haake Rheocord). Previous papers have given theoretical demonstration of the non-monotonic character of the shear stress-shear rate function, s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}), which makes it possible to explain the extrusion behavior of a high molecular weight HDPE. In capillary rheometry, it is not possible to obtain the values of s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}) into the “well zone” of this function because the compressibility of the polymer creates a phenomenon of oscillation in the barrel affecting the die output flow rate and the pressure loss. The M(N) function measured by the Haake Rheocord is a complete representation of the s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}) function, although the capillary rheometer only gives a partial representation of this function. The transformation of the M(N)function into s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}) is quite difficult because of the complex geometry of the Haake Rheocord measuring head. The “critical points” of the s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}) function in the capillary rheometer (appearance of oscillations), can be correlated to the maximum points of the M(N) function in the Haake Rheocord at constant temperature. The non-monotonic aspect of the s(\documentclass{article}\pagestyle{empty}\begin{document}$ {\rm \dot \gamma } $\end{document}) function provides an important technological application: extrusion of a high molecular weight HDPE at an increased flow rate at low temperatures.