Physico-chemical properties of ethanol–diesel blend fuel and its effect on performance and emissions of diesel engines

The effects of different ethanol–diesel blended fuels on the performance and emissions of diesel engines have been evaluated experimentally and compared in this paper. The purpose of this project is to find the optimum percentage of ethanol that gives simultaneously better performance and lower emissions. The experiments were conducted on a water-cooled single-cylinder Direct Injection (DI) diesel engine using 0% (neat diesel fuel), 5% (E5–D), 10% (E10–D), 15% (E15–D), and 20% (E20–D) ethanol–diesel blended fuels. With the same rated power for different blended fuels and pure diesel fuel, the engine performance parameters (including power, torque, fuel consumption, and exhaust temperature) and exhaust emissions [Bosch smoke number, CO, NO_x, total hydrocarbon (THC)] were measured. The results indicate that: the brake specific fuel consumption and brake thermal efficiency increased with an increase of ethanol contents in the blended fuel at overall operating conditions; smoke emissions decreased with ethanol–diesel blended fuel, especially with E10–D and E15–D. CO and NO_x emissions reduced for ethanol–diesel blends, but THC increased significantly when compared to neat diesel fuel.     

Using renewable alternative fuels and studying their impact on the performance and emissions of compression ignition engines

This practical study examined the effect of engine torque on engine performance and emissions. The most important parameters of engine performance are thermal efficiency, brake power (BP), and specific fuel consumption. As for exhaust emissions, the most important of which are hydrocarbons (HCs), carbon monoxide (CO), and nitrogen oxides (NO_x). The experiment was conducted for a single-cylinder, four-stroke compression ignition engine. Mixtures (B0, B10, B20, B30, and B40) were taken from biodiesel prepared from sunflower oil by the esterification method. The engine speed was fixed at 1700 rpm, and torque variable was from 0 to 10 N m. The results indicated a decrease in engine BP by an average of 19.5 W, a decrease in thermal efficiency by an average of 1.058%, while an increase in fuel consumption by an average of 0.095 kg/kW h⁻¹ compared to diesel. As for exhaust emissions, HC emissions decreased by 5.8 ppm, while CO decreased by 0.0207%, and NO_x emissions increased by 138.5 ppm compared to diesel, due to changes in the properties of biodiesel, such as high density, viscosity, and low calorific value compared to the properties of regular diesel     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Performance, emissions and heat release characteristics of direct injection diesel engine operating on diesel oil emulsion

Emulsions of diesel and water are often promoted as being able to overcome the difficulty of simultaneously reducing emissions of both oxidises of nitrogen (NO_x) and particulate matter from diesel engines. In this paper we present measurements of the performance and NO_x and hydrocarbon emissions of a diesel engine operating on a typical diesel oil emulsion and examine through the use of heat release analysis differences found during its combustion relative to standard diesel in the same engine. While producing similar or greater thermal efficiency and improved NO_x and hydrocarbon emission outcomes, use of the emulsion also results in an increase in brake specific fuel consumption. Use of the emulsion is also shown to result in a retarded fuel injection, but smaller ignition delay for the same engine timing. As a result of these changes, cylinder pressures and temperatures are lower.     

Influence of advanced injection timing on the performance and emissions of CI engine fueled with ethanol‐blended diesel fuel

Ethanol has been considered as an alternative fuel for diesel engines. On the other hand, injection timing is a major parameter that sensitively affects the engine performance and emissions. Therefore, in this study, the influence of advanced injection timing on the engine performance and exhaust emissions of a single cylinder, naturally aspirated, four stroke, direct injection diesel engine has been experimentally investigated when using ethanol‐blended diesel fuel from 0 to 15% with an increment of 5%. The original injection timing of the engine is 27° crank angle (CA) before top dead center (BTDC). The tests were conducted at three different injection timings (27, 30 and 33° CA BTDC) for 30 Nm constant load at 1800 rpm. The experimental results showed that brake‐specific energy consumption (BSEC), brake‐specific fuel consumption (BSFC), NO_x and CO₂ emissions increased as brake‐thermal efficiency (BTE), smoke, CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. Comparing the results with those of original injection timing, NO_x emissions increased and smoke, HC and CO emissions decreased for all test fuels at the advanced injection timings. For BSEC, BSFC and BTE, advanced injection timings gave negative results for all test conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Comparison of the effects of EGR and lean burn on an SI engine fueled by hydrogen-enriched low calorific gas

A naturally aspirated spark ignition (SI) engine fueled by hydrogen-blended low calorific gas (LCG) was tested in both exhaust gas recirculation (EGR) and lean burn modes. The “dilution ratio” was introduced to compare their effects on engine performance and emissions under identical levels of dilution. LCG composed of 40% natural gas and 60% nitrogen was used as a main fuel, and hydrogen was blended with the LCG in volumes ranging from 0 to 20%. The engine test results demonstrated that EGR operations at stoichiometry showed a narrower dilution range, inferior combustion characteristics, lower brake thermal efficiency, faster nitrogen oxides (NO_x) suppression, and higher total hydrocarbon (THC) emissions for all hydrogen blending rates compared to lean burn. These trends were mainly due to the increased oxygen deficiency as a result of using EGR in LCG/air mixtures. Hydrogen enrichment of the LCG improved combustion stability and reduced THC emissions while increasing NO_x. In terms of efficiency, hydrogen addition induced a competition between combustion enhancement and increases in the cooling loss, so that the peak thermal efficiency occurred at 10% H₂ with excess air ratio of 1.5. The engine test results also indicated that a close-to-linear NO_x-efficiency relationship occurred for all hydrogen blending rates in both operations as long as stable combustion was achieved. NO_x versus combustion duration analysis showed that adding H₂ reduced combustion duration while maintaining the same level of NO_x. The methane fraction contained in the THC emissions decreased slightly with an increase in hydrogen enrichment at low EGR or excess air dilution ratios, but this tendency was diminished at higher dilution ratios because of the combined dilution effects from the inert gas in the LCG and the diluents (EGR or excess air).     

Effect of ethanol blending with biodiesel on engine performance and exhaust emissions in a CI engine

The use of biodiesel as an alternative diesel engine fuel is increasing rapidly. However, due to technical deficiencies, they are rarely used purely or with high percentages in unmodified diesel engines. Therefore, in this study, we used ethanol as an additive to research the possible use of higher percentages of biodiesel in an unmodified diesel engine. Commercial diesel fuel, 20% biodiesel and 80% diesel fuel, called here as B20, and 80% biodiesel and 20% ethanol, called here as BE20, were used in a single cylinder, four strokes direct injection diesel engine. The effect of test fuels on engine torque, power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature, and CO, CO₂, NO_x and SO₂ emissions was investigated. The experimental results showed that the performance of CI engine was improved with the use of the BE20 especially in comparison to B20. Besides, the exhaust emissions for BE20 were fairly reduced.     

Performance and exhaust emissions of a gasoline engine with ethanol blended gasoline fuels using artificial neural network

The purpose of this study is to experimentally analyse the performance and the pollutant emissions of a four-stroke SI engine operating on ethanol–gasoline blends of 0%, 5%, 10%, 15% and 20% with the aid of artificial neural network (ANN). The properties of bioethanol were measured based on American Society for Testing and Materials (ASTM) standards. The experimental results revealed that using ethanol–gasoline blended fuels increased the power and torque output of the engine marginally. For ethanol blends it was found that the brake specific fuel consumption (bsfc) was decreased while the brake thermal efficiency (η_b.th.) and the volumetric efficiency (η_v) were increased. The concentration of CO and HC emissions in the exhaust pipe were measured and found to be decreased when ethanol blends were introduced. This was due to the high oxygen percentage in the ethanol. In contrast, the concentration of CO₂ and NO_x was found to be increased when ethanol is introduced. An ANN model was developed to predict a correlation between brake power, torque, brake specific fuel consumption, brake thermal efficiency, volumetric efficiency and emission components using different gasoline–ethanol blends and speeds as inputs data. About 70% of the total experimental data were used for training purposes, while the 30% were used for testing. A standard Back-Propagation algorithm for the engine was used in this model. A multi layer perception network (MLP) was used for nonlinear mapping between the input and the output parameters. It was observed that the ANN model can predict engine performance and exhaust emissions with correlation coefficient (R) in the range of 0.97–1. Mean relative errors (MRE) values were in the range of 0.46–5.57%, while root mean square errors (RMSE) were found to be very low. This study demonstrates that ANN approach can be used to accurately predict the SI engine performance and emissions.     

Experimental investigation of the effect of compression ratio and injection pressure in a direct injection diesel engine running on Jatropha methyl ester

Being a fuel of different origin, the standard design parameters of a diesel engine may not be suitable for Jatropha methyl ester (JME). This study targets at finding the effects of the engine design parameters viz. compression ratio (CR) and fuel injection pressure (IP) jointly on the performance with regard to fuel consumption (BSFC), brake thermal efficiency (BTHE) and emissions of CO, CO₂, HC, NO_x and Smoke opacity with JME as fuel. Comparison of performance and emission was done for different values of compression ratio along with injection pressure to find best possible combination for operating engine with JME. It is found that the combined increase of compression ratio and injection pressure increases the BTHE and reduces BSFC while having lower emissions. For small sized direct injection constant speed engines used for agricultural applications (3.5 kW), the optimum combination was found as CR of 18 with IP of 250 bar.     

Performance and emissions characteristics of a lean-burn marine natural gas engine with the addition of hydrogen-rich reformate

The exhaust gas-fuel reforming technique known as reformed exhaust gas recirculation (REGR) can generate on-board hydrogen-rich gas mixture (i.e., reformate) by catalytic reforming of the exhaust gas and fuel added into the reformer and then recirculate the reformate into the engine cylinder, which can realize the combination of hydrogen-rich lean combustion and exhaust gas recirculation. The REGR technique can be employed to achieve efficient and stable lean-burn combustion for the marine engine fueled with natural gas (i.e., marine NG engine) and it is considered as an effective way to meet the stringent ship emissions regulations. In the present study, an experimental investigation into the effects of reformate addition ratio (R_re) and excess air ratio (λ) on the combustion and emissions characteristics of a marine NG engine under various loads was conducted, and the potential of applying the REGR technique in a marine NG engine to achieve low emissions (i.e., International Maritime Organization Tier Ⅲ emissions legislations for international ships) was discussed. The results indicate that the addition of the hydrogen-rich reformate gases can extend lean-burn limit. For a given λ, the flame development duration and rapid combustion duration decrease with the increase of R_re, and the combustion efficiency is improved. The brake specific NO_x emissions first increase and then decrease with the increase of R_re due to the competition between the combustion phase and total heat release value. The brake specific THC emissions decline with the increase of R_re, while the reverse holds for the brake specific CO emissions, and the behavior tends to be obvious under large λ. It is demonstrated that the combination of REGR and the lean-burn combustion strategy can improve the trade-off relationship between the NO_x emissions and brake specific fuel consumption of the marine NG engine to meet the IMO Tier Ⅲ NO_x emissions legislations and maintain relatively low brake specific fuel consumption.     

Effect of hydrogen and LPG addition on the efficiency and emissions of a dual fuel diesel engine

This paper presents some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, liquefied petroleum gas (LPG) and mixture of LPG and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), NO_x and smoke are presented here. The paper also includes vital information regarding performances of the engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum enhancement in the brake thermal efficiency is 17% which is obtained with 30% of secondary fuel. When only LPG is used as secondary fuel, maximum enhancement in the brake thermal efficiency (of 6%) is obtained with 40% of secondary fuel. Compared to the pure diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x and smoke reduces in both cases. On the other hand, when 40% of mixture of LPG and hydrogen is used (in the ratio 70:30) as secondary fuel, brake thermal efficiency enhances by 27% and HC emission reduces by 68%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and LPG is used as the secondary fuel at higher than 10% load condition.     

Experimental and numerical investigation of effects of CNG and gasoline fuels on engine performance and emissions in a dual sequential spark ignition engine

Compared to widening usage of CNG in commercial gasoline engines, insufficient but increasing number of studies have appeared in open literature during last decades while engine characteristics need to be quantified in exact numbers for each specific fuel converted engine. In this study, a dual sequential spark ignition engine (Honda L13A4 i-DSI) is tested separately either with gasoline or CNG at wide open throttle. This specific engine has unique features of dual sequential ignition with variable timing, asymmetrical combustion chamber, and diagonally positioned dual spark-plug. Thus, the engine led some important engine technologies of VTEC and VVT. Tests are performed by varying the engine speed from 1500 rpm to 4000 rpm with an increment of 500 rpm. The engine’s maximum torque speed of 2800 rpm is also tested. For gasoline and CNG fuels, engine performance (brake torque, brake power, brake specific fuel consumption, brake mean effective pressure), emissions (O₂, CO₂, CO, HC, NO_x, and lambda), and the exhaust gas temperature are evaluated. In addition, numerical engine analyses are performed by constructing a 1-D model for the entire test rig and the engine by using Ricardo-Wave software. In the 1-D engine model, same test parameters are analyzed, and same test outputs are calculated. Thus, the test and the 1-D engine model are employed to quantify the effects of gasoline and CNG fuels on the engine performance and emissions for a unique engine. In general, all test and model results show similar and close trends. Results for the tested commercial engine show that CNG operation decreases the brake torque (12.7%), the brake power (12.4%), the brake mean effective pressure (12.8%), the brake specific fuel consumption (16.5%), the CO₂ emission (12.1%), the CO emission (89.7%). The HC emission for CNG is much lower than gasoline. The O₂ emission for CNG is approximately 55.4% higher than gasoline. The NO_x emission for CNG at high speeds is higher than gasoline. The variation percentages are the averages of the considered speed range from 1500 rpm to 4000 rpm.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Hydrogen enriched waste oil biodiesel usage in compression ignition engine

In the present study, hydrogen enrichment for biodiesel-diesel blends was evaluated to investigate the performance and emission characteristics of a compression ignition engine. Biodiesel was obtained from waste oil and blended to pure diesel fuel by volume fraction of 0%, 10% and 20%. After that, pure hydrogen was introduced through the intake air at different flow rates. Effects of pure hydrogen on performance and emission characteristics were investigated by evaluating power, torque, specific fuel consumption, CO, CO₂ and NO_x emissions. Experimental study revealed that waste oil biodiesel usage deteriorated performance and emission parameters except CO emissions. However, the enrichment test fuels with hydrogen fuel can improve performance characteristics and emission parameters, whereas it increased NO_x emissions. Brake thermal efficiency and specific fuel consumption were improved when the test fuels enriched with hydrogen gas. Because of absence of carbon atoms in the chemical structure of the hydrogen fuel, hydrogen addition dropped CO and CO₂ emissions but increment in cylinder temperature caused rising in NO_x emissions.     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Performance of Euro III common rail heavy duty diesel engine fueled with Gas to Liquid

The effect of synthetic diesel fuel made from natural gas (Gas to Liquid, GTL) on the engine performances (such as power, efficiency and emission) was carried out on one Euro III common rail (CR) heavy duty (HD) diesel engine without any modification. The results showed that the engine fueled with GTL had some variations compared with the one fueled with petroleum-based low sulfur diesel fuel (sulfur content less 50 ppm). The maximum torque and power were decreased by 1.3% and 1.9%, respectively. The specific fuel consumption increased in volume but had no change in mass. Under the load characteristics, the NO_x, CO and THC were reduced by 13%, 55% and 55%, respectively. During the ESC cycle test, the NO_x, CO, THC and PM were reduced by 5.2%, 19.3%, 19.8% and 33%, respectively.     

Performance and emission characteristics of QHCCI dimethyl ether engine

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NO _x emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NO _x , HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NO _x emission. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(3): 67–70 [译自: 内燃机工程]     

Combined effect of injection timing,EGR and injection pressure in reducing the NOx emission of a biodiesel blend

In this study, an attempt was made to reduce the higher oxides of nitrogen (NO_x) emission of a crude rice bran oil methyl ester (CRBME) blend through modification of combustion process by retarding fuel injection timing and exhaust gas recirculation at an increased fuel injection pressure. At modified condition, delay period and peak pressure of CRBME blend were lower than those at normal condition. The occurrence of maximum heat release rate retarded with a higher magnitude when compared with normal condition. Experimental results show that as a result of combustion modification, NO_x and carbon monoxide emissions were reduced significantly with marginal increase in smoke density. Brake thermal efficiency and unburnt hydrocarbon emissions of the engine were increased significantly as a result of this modification process. This investigation shows that the NO_x emission of a biodiesel blend can be reduced with less sacrifice on smoke density and increase in the brake thermal efficiency by modifying the combustion process.     

Effect on performance and emissions of a dual fuel diesel engine using hydrogen and producer gas as secondary fuels

Energy is an essential prerequisite for economical and social growth of any country. Skyrocketing of petroleum fuel cost s in present day has led to growing interest in alternative fuels like CNG, LPG, Producer gas, Biogas in order to provide suitable substitute to diesel for a compression ignition engine. This paper discusses some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, producer gas (PG) and mixture of producer gas and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), and NO_x are presented here. The paper also contains vital information relating to the performances of an engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum increase in the brake thermal efficiency is 7% which is obtained with 20% of secondary fuel. When only producer gas is used as secondary fuel, maximum decrease in the brake thermal efficiency of 8% is obtained with 30% of secondary fuel. Compared to the neat diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x reduces in all Cases. On the other hand, when 40% of mixture of producer gas and hydrogen is used (in the ratio (60:40) as secondary fuel, brake thermal efficiency reduces marginally by 3%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and producer gas is used as the secondary fuel at higher than 13% load condition. Based on the performance studied, a mixture of producer gas and hydrogen in the proportion of 60:40 may be used as a supplementary fuel for diesel conservation.