奥氏体不锈钢316L在ECAP过程中的组织演化及力学性能

对奥氏体不锈钢316L进行等效应变为1.02的6道次室温等通道挤压(ECAP)试验。结果表明,在ECAP挤压过程中316L发生了剪切滑移变形和孪生变形及晶粒碎化,经过4和6道次挤压后分别得到平均晶粒尺寸约80 nm和约61 nm的均匀分布的等轴晶粒。在1道次ECAP挤压后316L的抗拉强度由674 MPa增加到984 MPa, 规定塑性延伸强度则由594 MPa增加到922 MPa,维氏显微硬度由116.33 HV增加到328.31 HV,但是塑性下降严重,可以通过600 ℃后续退火处理进行改善。     

固溶温度对316LN奥氏体不锈钢微观组织和高温力学性能的影响

对316LN奥氏体不锈钢进行了不同温度(1020、1050和1070℃)的固溶处理,利用电子万能试验机对316LN奥氏体不锈钢在300℃的高温环境下进行单轴拉伸试验,采用光学显微镜(OM)、透射电镜(TEM)和扫描电镜(SEM)对其微观组织和高温力学性能进行分析表征.结果 表明:随着固溶温度的升高,316LN奥氏体不锈...     

粉末形貌对选区激光熔化316L不锈钢力学性能的影响

以气雾化316L不锈钢粉为原料,结合等离子球化和选区激光熔化技术制备了不锈钢块体,并用XRD、SEM、激光粒度仪、振实密度仪和万能力学试验机等对等离子球化粉体和选区激光不锈钢块的组织结构和性能进行了表征.结果表明:316L不锈钢粉经等离子球化处理后,不规则扁平状颗粒数量减少,球形颗粒数量增加,振实密度与松装密度的比值(...     

表面机械研磨处理对316L不锈钢组织和性能的影响

对2.8mm厚的316L不锈钢板的上下表层进行机械研磨处理(SMAT),对经过不同时间的SMAT后的样品的表层组织进行金相观察,并测量SMAT不同时间的样品的硬度、抗拉强度.结果表明,经过表面机械研磨处理不同时间后,在316L不锈钢板表层获得了不同厚度的表面强化层,强化层组织为沿厚度方向由纳米晶层向微米晶层过渡的梯度组织;随着SMAT时间的增加,总的强化层厚度增加;表面组织的变化导致了表面硬度明显增加,整体材料的屈服强度增加;表面机械研磨处理时间对性能的影响并非线性增加,表面硬度和整体材料的屈服强度在处理5min时增加显著,处理时间继续增加到15、30和60min,它们的增加速度很小.拉伸断口表面形貌的扫描电镜观察表明,经过5min处理后的样品,表层的剪切唇变形区域面积增加,断口微观特征为长条状的韧窝,但是随着处理时间的增加,剪切唇区的尺寸并没有继续增加,而是开始下降,表面硬化区域的增加造成了塑性变形能力的下降.     

Fatigue behaviour of low temperature carburised AISI 316L austenitic stainless steel

Low temperature carburising (LTC) was applied to AISI316L austenitic stainless steel and its effect on microstructure and fatigue behaviour was investigated. LTC treatment enhances surface hardness and wear resistance of the steel without reducing its corrosion resistance. Surface hardness up to 1150 Vickers was achieved in the carburised layer, thanks to the formation of the so-called “S-phase”, a carbon-supersaturated austenite phase. The XRD evaluation of treated material verified expanded austenite with no evidence of carbide precipitation. Rotating bending fatigue tests showed that the low temperature carburising treatment enhances the fatigue strength of the 316L steel by 40% with respect to the untreated material due to the high residual stresses present in the treated layer. A major temperature increase was found testing the LTC specimens, with a peak value at the end of the test up to 600 °C. By air cooling the LTC specimens during the tests, a further increase of fatigue strength up to 70% was achieved with respect to the untreated material. Fatigue cracks in the surface-treated specimens always nucleated near the boundary between the carburised case and the core.     

316L不锈钢扩散焊接头的微观结构和力学性能

针对不同焊接参数的含镍中间层316L不锈钢扩散焊接头,进行室温和550℃高温拉伸实验,采用SEM、XRD和金相显微镜分析接头区域的微观结构和相分布。结果表明:接头的室温力学性能随焊接温度的提高而降低,而高温力学性能随温度的提高而提高。XRD分析表明,焊接过程中产生的Fe0.64Ni0.36导致接头区域的相组成不均一;在高温拉伸实验时,DB2和DB3接头中的Fe0.64Ni0.36发生相变,强度和塑性更好的FeNi3是接头高温强度提高的原因。     

Electropolishing of 316L stainless steel for anticorrosion passivation

316L stainless steel is deemed an indispensable material in the semiconductor industry. In many instances, the surface of the production equipment needs to be treated for low-corrosion passivation, good finish, weldability, and cleanliness. The process characteristics of electropolishing meet these requirements well. The current study investigates the effects of the major processing parameters on the anticorrosion performance and the surface roughness. The electrolyte with 10% water content and a ratio between H₂SO₄ and H₃PO₄ of 4 and 6 has been proven to be successful, showing no corrosion pitting points on the specimen surface. The electrolyte temperature of 85±10 °C and the electrical current density of 0.5 to 1.0 A/cm² are found to be optimal. The processing time beyond 3 to 5 min produces no further improvement. The addition of 10% glycerin provides a very fine surface (maximum roughness of 0.05 μm), while the anticorrosion performance is deteriorated. The results obtained are useful for the manufacture of the semiconductor equipment.     

Processing and mechanical properties of porous 316L stainless steel for biomedical applications

Highly porous 316L stainless steel parts were produced by using a powder metallurgy process, which includes the selective laser sintering（SLS） and traditional sintering. Porous 316L stainless steel suitable for medical applications was successfully fabricated in the porosity range of 40%-50% （volume fraction） by controlling the SLS parameters and sintering behaviour. The porosity of the sintered compacts was investigated as a function of the SLS parameters and the furnace cycle. Compressive stress and elastic modulus of the 316L stainless steel material were determined. The compressive strength was found to be ranging from 21 to 32 MPa and corresponding elastic modulus ranging from 26 to 43 GPa. The present parts are promising for biomedical applications since the optimal porosity of implant materials for ingrowths of new-bone tissues is in the range of 20%-59% （volume fraction） and mechanical properties are matching with human bone.     

高温酸性溶液中316L不锈钢/Ni-Cu-P镀层的耐蚀性能

为了改善316L 不锈钢在高温酸性溶液中的耐蚀性,采用化学镀技术在316L 不锈钢表面沉积高铜高磷Ni?Cu?P 镀层。采用扫描电镜(SEM)、能谱仪(EDS)和 X 射线衍射仪(XRD)对其结构进行分析,利用极化曲线、阻抗谱(EIS)及浸泡腐蚀试验对其在高温酸性溶液中的耐蚀性进行研究。结果表明,Ni?Cu?P 镀层由铜含量分别为19.98%和39.17%(质量分数)两种类型的胞状组织组成;在高温酸性溶液中,这种新型Ni?Cu?P镀层可显著改善316L不锈钢的耐蚀性;镀态镀层的耐蚀性优于热处理态的;镀态镀层和经673 K热处理镀层的腐蚀机制是选择性腐蚀,而经773和873 K热处理镀层的腐蚀机制为点腐蚀。     

316奥氏体不锈钢低温气体渗碳层组织与强化性能

采用自主研发的低温气体渗碳技术对AISI316奥氏体不锈钢进行处理,目的是增强耐磨性且不损害其耐蚀性。对低温气体渗碳层显微组织、硬度梯度、耐蚀性和耐磨性进行分析。结果表明:低温气体渗碳层硬度梯度变化与其组织和碳浓度有一定关系,随渗碳层深度的不同表现出不同的组织和性能。低温气体渗碳处理前后AISI316奥氏体不锈钢的磨损机制由粘着磨损转变成磨粒磨损,S相是提高耐磨性的主要因素,470℃时表现出较好的耐磨性,其耐蚀性基本保持不变。     

电弧喷涂316L不锈钢涂层的结构与性能

采用电弧喷涂优化工艺制备316L不锈钢涂层,利用扫描电镜、能谱仪和X射线衍射仪等对涂层的组织及物相进行分析,同时对涂层的硬度、结合强度进行了测定。结果表明：涂层具有典型的层状形貌,涂层截面较为致密,局部区域出现粗大孔洞;涂层与基体之间主要为机械结合,结合强度较高;涂层硬度的最大值出现在涂层中部,靠近界面的基体组织发生加工硬化。     

增氮降镍对316奥氏体不锈钢高温拉伸性能的影响

利用Gleeble-1500D热模拟机对不同成分316奥氏体不锈钢分别在950、1000、1050、1100 ℃以0.05 s^-1的应变速率下进行高温拉伸试验,通过分析试验曲线、断口形貌、变形区以及未变形区组织,研究增氮降镍对试验钢高温拉伸性能的影响。结果表明,增氮降镍使单位截面的杂质偏聚数量上升,恶化了试验钢的断口形貌,从而降低了钢材的热塑性,断面收缩率平均下降了37.5%;增氮降镍使钢材的抗拉强度平均提高了42.5%。     

Strength and ductility of 316L austenitic stainless steel strengthened by nano-scale twin bundles

By means of dynamic plastic deformation (DPD) with high strain rates, a bulk nanostructured 316L austenitic stainless steel consisting of nano-sized grains embedded with bundles of nanometer-thick deformation twins was synthesized. The average transverse grain size is ∼33 nm and the twin/matrix lamellar thickness is ∼20 nm. The nano-twin bundles constitute ∼24% in volume. The nanostructured samples exhibit a high tensile strength of ∼1400 MPa but a limited ductility with a uniform elongation of ∼2%. Subsequent thermal annealing of the as-DPD samples in a temperature range of 730-800 °C led to a single-phased austenite structure consisting of static recrystallized (SRX) micro-sized grains embedded with remaining nano-twin bundles and nano-grains. The annealed DPD samples exhibit an enhanced strength-ductility synergy and much more enhanced work-hardening rates than the as-deformed samples. Work-hardening rates of the annealed DPD samples can be even higher than that of the original CG sample. Tensile ductility was found to increase almost linearly with the volume fraction of SRX grains. A combination of 1.0 GPa tensile strength with an elongation-to-failure of ∼27% is achieved in the annealed DPD 316L stainless steel samples.     

奥氏体不锈钢焊缝金属的电化学腐蚀性能

采用PASTAT30型恒电位仪测试了SUS 316奥氏体不锈钢钨极氩弧焊TIG,熔化极氩弧焊MIG和钨极氩弧焊加填丝TIG M焊缝金属的电化学腐蚀性能.结果表明,在质量分数9.8%H2SO4溶液中,母材及焊缝的抗电化学腐蚀能力由大到小的顺序为母材＞TIG M焊缝＞MIG焊缝＞TIG焊缝,在质量分数5.0%HCl溶液中为母材＞MIG焊缝＞TIG M焊缝＞TIG焊缝,由此可知TIG焊缝金属的抗腐蚀能力最弱.由Tafel曲线可知,SUS316奥氏体不锈钢在H2SO4溶液中的钝化区间较长,在HCl溶液中的钝化区间很短暂,所以不锈钢在盐酸溶液比硫酸溶液中抗腐蚀性能差.晶间腐蚀试验结果与9.8%H2SO4溶液中电化学腐蚀试验结果相同.     

Determination of susceptibility to intergranular corrosion and electrochemical reactivation behaviour of AISI 316L type stainless steel

In this study, double loop electrochemical potentiokinetic reactivation (DLEPR) test was applied to determine the degree of sensitization in 316L type stainless steel, where obtained results were correlated with revealed microstructures after oxalic acid test and weight loss measurements of Streicher and Huey acid tests. Best agreement was provided with test parameters which are 1 M H₂SO₄ and 0.005 M KSCN at 0.833 mV/s scan rate at 30 °C. Specimens were classified structurally as absence of chromium carbides - step, no single grain completely surrounded by carbides - dual and one or more grain completely surrounded by carbides - ditch, in the as-etched structure, if the I_r:I_a (×100) ratios were obtained to be between 0 and 0.2, 0.2 and 5.0 and 5.0 and higher, respectively. It was also found that at high KSCN concentrations, reactivation current profile skewed to higher potentials where this was attributed the formation of metastable pits, during the anodic scan of the test procedure.     

Corrosion of a 316L stainless steel in a gaseous environment polluted with HCl: Mechanism

The corrosion of a 316L stainless steel (SS) exposed to a humid gas flow polluted with HCl has been studied. The mixture is carried out in a reactor connected to two gas feedthroughs: one with wet air and one with HCl(g). The corrosion mechanism comprehension is based on several steps. The presence of humid air polluted by HCl involves the creation of a precursor film that can evolve to droplet formation. In contact with this acid and chloride concentrated electrolyte, the 316L SS corrodes producing soluble ferrous chloride. This corrosion product can evolve to the oxide formation, depending of the HCl concentration. For high concentrations, 316L SS corrodes uniformly. However, this phenomenon is accompanied by pits when the HCl concentration is not sufficient or the HCl flow is not continuous. The particularity of the corrosion mechanisms is shown as well as the problems using materials in an HCl-polluted gaseous environment.     

化学成分对316L奥氏体不锈钢组织及变形行为的影响

利用万能试验机对不同镍当量(Nieq)的316L不锈钢热轧钢板进行常温单轴拉伸试验,借助扫描电镜(SEM)和透射电镜(TEM)对其拉伸变形前后的微观组织进行观察,探索镍当量对316L不锈钢微观组织及性能的影响规律。结果表明,固溶态试验钢的组织均为奥氏体组织及少量高温δ相,强度随Nieq的升高而降低,塑性和韧性随Nieq升高而增加;拉伸断口均呈韧性断裂特征,且随Nieq的提高,韧窝的数量减少,韧窝尺寸增加;TEM显示,变形后的试验钢均未发生马氏体相变,Nieq较低时,变形量大的地方位错密度高,发生位错交互作用,局部有形变孪晶生成,且随着Nieq的增加,形变孪晶密度增大,出现相互交叉、阻滞。     

相对流速对316L钢焊缝在液态铅铋合金中腐蚀行为的影响

在核工业领域,316L不锈钢因其优异的性能常被作为核用钢种,液态铅铋合金常作为加速器次临界驱动系统(ADS)的冷却剂,高速流动的液态铅铋合金(LBE)会对316L不锈钢焊缝造成氧化腐蚀,同时氧化腐蚀后的产物也会对液态LBE造成污染,所以研究316L不锈钢焊缝在液态铅铋合金中的腐蚀行为具有重要意义. 文中对比研究了使用母材作为焊丝进行TIG焊的316L不锈钢焊缝在550 ℃动态(相对流速为1.70,2.31,2.98 m/s)液态LBE中的耐腐蚀性能,试验时间为1 500 h. 结果表明,三组试样都生成了双氧化层,外氧化层主要为Fe₃O₄,内氧化层主要为FeCr₂O₄,内氧化层相对于外氧化层较致密;随着流速的提高,元素的传质过程变快,氧化腐蚀加剧,内氧化层增厚.     

Effect of DC plasma nitriding temperature on microstructure and dry-sliding wear properties of 316L stainless steel

A wear resistant nitrided layer was formed on 316L austenitic stainless steel substrate by DC plasma nitriding (DCPN). The structural phases, micro-hardness and dry-sliding wear behavior of the nitrided layer were investigated by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDS), micro-hardness tester and ring-on-block wear tester. The results show that a single expanded austenite layer (S-phase) and a single CrN nitride layer were formed at 400 °C and 480 °C, respectively. In addition, the S-phase layers formed on the samples exhibited the best dry-sliding wear resistance under ring-on-block contact configuration test. Wear of the untreated 316L was sever and characterized by strong adhesion, abrasion and oxidation mechanism, whilst wear of the DCPN-treated 316L was mild and dominated by plastic deformation, slight abrasion and frictional polishing.     

Peening action and residual stresses in high-velocity oxygen fuel thermal spraying of 316L stainless steel

316L stainless steel powder was sprayed by a high-pressure high-velocity oxygen fuel (HVOF) process. Effects of powder size and the pressure in the combustion chamber on the velocity and temperature of sprayed particles were studied by using an optical instrument, first, at the substrate position. A strong negative correlation between the particle temperature and the diameter was found, whereas the correlation between the velocity and the diameter was not significant. The pressure in the combustion chamber affected the velocity of sprayed particles significantly, whereas the particle temperature remained largely unchanged. In-situ curvature measurement was employed in order to study the process of stress generation during HVOF spraying. From the measured curvature changes, the intensity of peening action and the resultant compressive stress by HVOF sprayed particles were found to increase with the kinetic energy of the sprayed particles. The results were further used to estimate the stress distribution within the coatings. X-ray stress measurement revealed that the residual stress on the surface of the HVOF coatings is low and often in tension, but the stress inside the coatings is in a high level of compression.