新颖环形喷动床颗粒喷动特性实验研究

一种新颖的环形喷动床由内外两个不同内径、同心的垂立圆筒组成,在环形空间底部设置多个喷口,在喷口两侧布置倾斜的导流板.研究颗粒在这种喷动床内的流动特性,探讨喷口结构、颗粒种类以及床内载料量对环形喷动床颗粒喷动特性的影响.实验结果表明:颗粒在环形喷动床内分为三个明显不同的区域,即颗粒填充移动区、密相喷动流化区以及稀相夹带区.当颗粒出现分区喷动后,随床内载料量的增多,填充移动区的高度维持不变,始终等于导流板的高度,而密相喷动区的高度不断增加.风量和颗粒种类对床层最大喷动量、密相喷动高度以及床层压力分布规律有着十分重要的影响.采用不同的喷口结构时,在相同的载料量下,直向喷口的密相喷动区高度更大,而且床内各测点的平均压力大于采用斜向喷口时的相应测点压力.     

导向管充气喷动床流体力学性能

在内径92mm的有机玻璃床内,对导向管充气喷动床的操作相图、床层压降、最小喷动速度及最大弃气速度进行了研究.实验采用4种颗粒为实验物料并采用空气为 喷动和弃气气体,通过对实验数据的回归得到用于计算或判别导向管弃气喷动床最小喷动速度和最大充气速度的计算式,以便为其设计和操作提供依据.     

双喷嘴矩形喷动床流动性能实验研究

在120 mm×240 mm的双喷嘴矩形不锈钢床内,对新型双喷嘴矩形导流管喷动床的最小喷动速度和喷动高度进行了研究,考察了喷动气速、粒径、静床层高度、导流管直径、导流管安装位置对最小喷动速度和喷动高度的影响。结果表明:最小喷动速度随颗粒直径、导流管直径、导喷距的增大而增大,随静床层高度的增大而减小;喷动高度随喷动气速的增大而增大,随导流管直径的增大而减小,受静床层高度和导喷距的影响不大,并得出了最小喷动速度的关联式。     

喷动流化床最大喷动压降的多因素影响与关联

基于截面200 mm×20 mm,高1600 mm,锥角60°的矩形喷动流化床,以二组分混合颗粒、单一组分球形颗粒及非球形颗粒为物料进行最大喷动压降的实验研究.结果表明,最大喷动压降随静止床高、颗粒密度、颗粒球形度及二组分混合颗粒体系中沉积组分分率增加而增大,随流化气速增大而减小;增大颗粒粒径或喷口宽度,呈现先减小后增...     

细颗粒喷动床的流体力学特性

在直径186 mm的喷动床中考察了细颗粒(d_p＝0.241～0.874 mm)体系的流体力学性质及夹带和磨损特性.采用不同的喷嘴直径(D_i＝6～14 mm)和锥底顶角(θ＝45°～80°)对其操作状态进行了研究,发现当D_i/d_p<19～21时可以形成稳定喷动.随着气体速度的增加,床层依次出现固定床、稳定喷动、不良喷动和腾涌等4个流动区域.实验测量的最小喷动速度与Mathur-Gishler关联式的误差在±15%之内.采用γ射线扫描仪测量了固体密度分布,结果表明喷动区的固体密度随高度的增加而增加,环流区的密度比松堆密度大3%～10%.颗粒的磨损和夹带随着气速的增大而增大,在稳定有序的喷动状态下变得最小.     

狭缝式矩型喷动床中多粒度颗粒体系的最小喷动速度

在150 mm×50 mm×1100 mm的矩形喷动床中,采用宽度为2, 4, 6 mm 的3种狭缝式气体分布板,研究了单一粒度组成和多粒度组成玻璃珠的最小喷动速度. 实验证明,矩形喷动床的最小喷动速度与物料的粒度和组成有关. 给出了最小喷动速度与颗粒粒径和粒度组成的关联式,作出了多粒度组成颗粒体系最小喷动速度的相图.     

小波分析方法在喷动床流型识别中的应用

在直径150 mm、静床层高280 mm的柱锥形喷动床中,采用平均粒径为1 mm、密度为2 770 kg/m~3的刚玉球为实验固相,采集不同气速下无导流管和带开孔导流管喷动床中的压力信号,通过小波分析与功率谱相结合的方法表征柱锥形喷动床的流型转变。首先利用平均压力法测得本实验条件下无导流管和带开孔导流管喷动床的最小喷动速度分别为0.57,0.50 m/s,然后采用Daubechies2小波对压力信号进行7层小波分解得出能反映喷动床流动特性的主频信号,再对主频信号进行功率谱分析。结果表明:无导流管和带开孔导流管喷动床的主频分别出现在D3(6.25—12.5 Hz)和D2(12.5—25 Hz)频段,且主频信号的功率谱图可以表征喷动床的3种流型:固定床、稳定喷动和不稳定喷动;开孔导流管喷动床的操作弹性(1相似文献   

双喷嘴矩形导流管喷动床喷动压降

引言 传统的柱锥形喷动床(CSBs)的应用受到一些因素的限制,例如处理物料能力、起始压力大及难以放大等,为此,Romankov等[1]最早提出了长方形截面的矩形喷动床结构,来克服CSBs的缺点.此后,Rocha等[2]用矩形喷动床进行了片剂包衣的研究.     

双喷嘴矩形喷动床压降的实验研究

在双喷嘴矩形喷动床内,以空气为喷动气体,研究了最大喷动压降与操作压降的变化规律和影响因素。实验表明：双喷嘴矩形喷动床的最大喷动压降和操作压降与颗粒粒径、床层高度及表观气速有关,而操作压降还与床体结构有关。在综合考虑各影响因素的基础上,得出了双喷嘴矩形喷动床最大喷动压降的经验关联式。     

带导流管液固喷动床的最小喷动速度研究

在截面为矩形有机玻璃喷动床内，使用四种粒径的窄筛分球形玻璃珠，以常温水作为喷动和辅助液体。综合考虑床体的几何尺寸、操作参数以及液体和颗粒的物性特征，系统研究带导流管喷动床的最小喷动速度，得出最小喷动速度的经验公式，为设计和操作提供参考。     

Hydrodynamic Characteristics of a Powder‐Particle Spouted Bed with Powder Entrained in Spouting Gas

Spouting of 3.7 mm polyvinyl chloride particles in a cone‐based cylindrical column is subjected to entrainment of FCC powder in the spouting air. It is found that the powder entrainment reduces the minimum spouting velocity, increases the bed pressure drop and reduces the maximum spoutable bed height. At any given bed height and value of U/U_ms, there is a critical value of powder loading ratio above which spouting gives way to slugging.     

Evaluation of flow regimes in a semi‐cylindrical spouted bed through statistical,mutual information,spectral and Hurst's analysis

Hydrodynamic studies were conducted in a semi‐cylindrical spouted bed column of diameter 150 mm, height 1000 mm, conical base included angle of 60° and inlet orifice diameter 25 mm. Pressure transducers at several axial positions were used to obtain pressure fluctuation time series with 1.2 and 2.4 mm glass beads at U/U_ms from 0.3 to 1.6, and static bed depths from 150 to 600 mm. The conditions covered several flow regimes (fixed bed, incipient spouting, stable spouting, pulsating spouting, slugging, bubble spouting and fluidization). Images of the system dynamics were also acquired through the transparent walls with a digital camera. The data were analyzed via statistical, mutual information theory, spectral and Hurst's Rescaled Range methods to assess the potential of these methods to characterize the spouting quality. The results indicate that these methods have potential for monitoring spouted bed operation.     

Determination of Minimum Spouting Velocities in Conical Spouted Beds

Minimum spouting velocities in conical spouted beds have been obtained from pressure drops versus the superficial gas velocity curves, based on both increasing and decreasing the superficial gas velocity. It has been shown that the minimum spouting velocity from decreasing the superficial gas velocity is lower than from increasing the superficial gas velocity in most cases. This phenomenon is similar to that in conventional spouted beds and different from the early works. The experimental results also showed that there isn't significant difference in the pressure drop and U_ms under identical operating conditions between semi‐circular and circular conical spouted beds, and the same U_ms can be obtained from absolute pressure drops at any position above the gas inlet. The U_ms is found to increase with increasing the cone angle and static bed height, as well as the gas inlet diameter to a less extent.     

Pressure drop in slotted spouted beds of grains: Comparison of data with models

Data obtained in a rectangular slot spouted bed for two different grains (wheat and oats) have been analyzed to determine the minimum spouting velocity (V_ms) and the minimum spouting pressure drop (ΔP_ms) as a function of the bed height.Three different aerodynamic regimes occur as the bed height is increased.The results are compared with the literature models for the conventional (conical-cylindrical) spouted bed.For shallow beds, the experimental minimum spouting velocity and minimum spouting pressure drop can be well represented by the Littman et al.'s two-dimensional model.     

Spouted bed hydrodynamics in a 0.91 m diameter vessel

Hydrodynamic measurements were obtained in a flat-based half-cylindrical column of diameter 0.91 m and inlet orifice diameters of 76 to 114 mm. Beds of 3.5 to 6.7 mm diameter particles with static depths of 0.53 to 1.83 m were spouted with air. In agreement with measurements by earlier workers in smaller columns, it was found necessary to operate with inlet orifice diameters less than about 30 times the mean particle diameter in order to be able to achieve stable spouting. Correlations for minimum spouting velocity developed on small vessels generally gave poor predictions for the large diameter vessel employed in this work and failed to predict the observed dependence of U_ms on the static bed height. Substantial dead regions where particles were stagnant were observed in the lower outer portion of the vessel. Other aspects of behaviour studied, including spout diameters and shapes, fountain heights, pressure profiles and gas velocities in the annulus, were qualitatively similar to those in smaller columns, although equations developed for the smaller vessels did not always provide accurate predictions.     

THE STABILITY OF WET SPOUTED BEDS

ABSTRACT

In granulation, coating or drying of slurries on inert particles a liquid phase is added to a gas-spouted bed. The effect of liquid injection on spouting velocity, fountain height, bed pressure drop and stability of the spouting regime is examined in a 0.15 m diameter bed with four types of inert particles 2 to 5 mm in size, 1140 to 2880 kg/m³ in true density, and 1.3 and 1400 mPa·s in liquid viscosity. Key factors are the liquid content and the presence of cohesive forces due to liquid bonds between particles. In a spoutability chart the maximum spoutable liquid content is related to the ratio of inertial force of a particle to the viscous or cohesive force exerted onto the particle by the liquid film. The spoutability chart serves to define regions of stable spouting.     

EXPERIMENTAL ANALYSIS OF A MECHANICALLY STIRRED SPOUTED BED DRYER

ABSTRACT

In order to increase the movement of the particles in the annular region of a conical spouted bed, a mechanical stirrer was incorporated. This led to a study of the fluid dynamics of the conical spouted bed of inert particles under different operating conditions: mass of inert particles, ratio of inert particles to suspension volumes, type of stirrer (2 designs) and stirrer speed.

The action of the stirrers resulted in increased movement of the particles, especially at low rpm values (≤ 90 rpm), with the loss of the annular region, and thus approaching the beds behavior to that of a fluidized bed. To characterize this novel type of spouted beds, the “minimum spouting flow” (Q_ms) parameter which is used usually was replaced by the “minimum pseudo-fluidizing flow” (Qmpr). The value of Q_mpf decreases when the agitation in the bed increases. A correlation for Q_mpf with the different operating conditions was developed.

Drying suspensions in the stirred spouted bed shows a considerable increase of drying capacity, over units without agitation.     

Particle segregation in a spouted bed of binary mixtures of particles

Minimum spouting velocity and segregation behaviour of binary mixtures of particles differing in size have been studied. The experiments were carried out in a bed of 20 cm diameter at superficial gas velocities up to 1.3 U_ms by use of silica sand of four different particle sizes from 0.655 to 2.23 mm. An empirical equation was proposed for the minimum spouting velocity of binary mixtures. The effects of the particle size difference and the superficial gas velocity on segregation were investigated. Results showed that considerable radial segregation as well as axial segregation occurred even for high gas velocity under the condition of large particle size difference.     

导向管喷动流化床的喷动气旁路分率

在内径为182 mm的喷动流化床中安装内径80 mm的导向管,以平均粒径为2.2 mm的尿素颗粒为物料,对喷动气旁路特性进行了实验研究,分别考察了夹带区高度、导向管长度、喷嘴内径、床层高度、喷动气速和流化气速对喷动气旁路分率的影响,结果表明随着喷动气速的增大,喷动气体旁路分率先增后减。导向管安装高度越高,气体旁路分率越大。床层高度增大喷动气体旁路分率略有降低。而喷嘴直径小于50 mm时气体旁路分率随喷嘴直径增大而提高,在大于50 mm时气体旁路分率随喷嘴直径增大维持不变。当气速较小时,导向管高度增大会引起气体旁路分率增大,引入少量流化气能有效地抑制喷动气旁路。