INVESTIGATION ON THE INCIPIENT FLUIDIZATION AND HEAT TRANSFER IN A CENTRIFUGAL FLUIDIZED BED DRYER

Based on the continuum theory, a physical model of gas-solid two phase flow in a centrifugal fluidized bed has been proposed. A set of governing equations to describe the fluidization state are obtained and solved numerically after some simplifying. The quantitative experimental study on the characteristics of the incipient fluidization in the centrifugal fluidized bed is performed to examine the proposed model. Gas-solid two phase heat transfer in CFB during a drying process is also conducted. The influences of bed thickness, particle diameter, physical properties of particle, rotating speed of the bed and the gas superficial velocity on heat transfer characteristics are examined. A correlation that can be used to calculate the heat transfer coefficients in the drying process in CFB is obtained.     

离心流化床干燥过程中传热传质的数值模拟

通过对典型的多孔湿物料在离心流化床中干燥过程的理论分析和实验研究 ,首次将含湿多孔介质传热传质过程和物料与气流之间的外部传递过程相耦合 ,导出了离心流化床的理论模型和控制方程组 ,对于离心流化床中湿物料的干燥过程引进了数值模拟 ,结果表明增加气体表观流速、控制入口气体的温度和相对湿度以及加大床体转速均对干燥有不同的影响     

Numerical investigation of gas-solid heat transfer in rotating fluidized beds in a static geometry

Gas-solid heat transfer in rotating fluidized beds in a static geometry is theoretically and numerically investigated. Computational fluid dynamics (CFD) simulations of the particle bed temperature response to a step change in the fluidization gas temperature are presented to illustrate the gas-solid heat transfer characteristics. A comparison with conventional fluidized beds is made. Rotating fluidized beds in a static geometry can operate at centrifugal forces multiple times gravity, allowing increased gas-solid slip velocities and resulting gas-solid heat transfer coefficients. The high ratio of the cylindrically shaped particle bed “width” to “height” allows a further increase of the specific fluidization gas flow rates. The higher specific fluidization gas flow rates and increased gas-solid slip velocities drastically increase the rate of gas-solid heat transfer in rotating fluidized beds in a static geometry. Furthermore, both the centrifugal force and the counteracting radial gas-solid drag force being influenced by the fluidization gas flow rate in a similar way, rotating fluidized beds in a static geometry offer extreme flexibility with respect to the fluidization gas flow rate and the related cooling or heating. Finally, the uniformity of the particle bed temperature is improved by the tangential fluidization and resulting rotational motion of the particle bed.     

离心流化床中强制对流换热的实验研究

对离心流化床干燥器中气体与被干燥颗粒物料之间的强制对流换热进行了实验研究,获得了各主要运行参数对气固换热系数的影响规律,并利用场协同原理分析了对流换热强化的机理. 实验证明,在一定转速范围内,在气流速度方向和热流方向（温度梯度方向）一致时,换热的准则关联式具有Nu＝CRePr的形式. 获得了满足Nu～RePr呈直线关系的Pe(Pe=RePr)数变化范围和临界Pe数,当Pe数大于临界值后,离心流化床中对流换热强度随Pe数增加而增大的趋势会明显减缓并偏离线性区.     

Gas backmixing in the dense region of a circulating fluidized bed

The gas backmixing characteristics in a circulating fluidized bed (0.1 m-IDx5.3-m high) have been determined. The gas backmixing coefficient (D_ba) from the axial dispersion model in a low velocity fluidization region increases with increasing gas velocity. The effect of gas velocity onD _ba in the bubbling bed is more pronounced compared to that in the Circulating Fluidized Bed (CFB). In the dense region of a CFB, the two-phase model is proposed to calculate D_bc from the two-phase model and mass transfer coefficient (k) between the crowd phase and dispersed phase. The gas backmixing coefficient and the mass transfer coefficient between the two phases increase with increasing the ratio of average particle to gas velocities (U_p/U_g).     

离心流化床中气固传热特性的实验研究

本文使用玻璃细珠、黄砂和氧化铝球在不同操作条件下进行了离心流化床气固两相间传热特性的实验研究．测定了气体入口、出口和床层温度随时间的变化．分析了床层厚度、粒径、物料性质、床体转速和气体流速等因素对气固传热特性的影响．首次获得了离心流化床气固两相传热的准则方程．     

Innovative Steam Drying of Empty Fruit Bunch with High Energy Efficiency

Empty fruit bunch (EFB) is one of the solid wastes from crude palm oil mills and has the lowest value for utilization compared to other solid wastes. To achieve an efficient utilization of EFB, drying is considered the first crucial process due to the high moisture content of EFB. In this study, EFB drying based on exergy recovery is proposed to achieve high energy efficiency. A fluidized bed is adopted as the main dryer. The proposed model is evaluated in terms of energy efficiency, especially regarding the influence of target moisture content and fluidization velocity. Up to 92% of the energy involved in the drying process can be recirculated. The total energy consumption for drying decreases as the target moisture content decreases, though there is no significant impact of fluidization velocity to total energy consumption. In addition, the required total length of the heat transfer tubes immersed inside the fluidized bed dryer is calculated because it relates to fluidization performance and economic issues. Lower target moisture content results in a longer heat transfer tube, and higher fluidization velocity leads to a shorter heat transfer tube.     

Computational Fluid Dynamics Study of Heat Transfer in Turbulent Fluidized Beds

The fluidization and heat transfer behaviors of a turbulent fluidized bed were investigated using computational fluid dynamics (CFD). The effects of inlet superficial velocity on heat transfer behaviors in a turbulent fluidized bed were analyzed and compared with those operated in other fluidization regimes. The effects of using particles belonging to different Geldart groups in a turbulent fluidized bed on fluidization and heat transfer behaviors were evaluated. For both fluidization regimes investigated, the solids temperature distribution during the heat transfer process became less uniform when the particle size was reduced.     

Flow regimes in circulating fluidized beds

Based on a comprehensive hydrodynamic analysis, a practical definition of the circulating fluidized bed (CFB) regime has been proposed. It was established that two flow regimes are involved in a CFB: fast fluidization and dense phase conveying. By demonstrating the variation of pressure gradient in both the lower and the upper section of the bed versus superficial gas velocity, the criteria for the determination of transition velocities have been obtained. Literature data which over wider operating conditions, particle properties and bed diameters from the basis of the obtained generalized correlations of transition velocities. A quantitative flow diagram is presented.     

离心流化床干燥器的流体力学及传热性能

以９种颗粒物料为研究对象,找出了影响离心流态化干燥系统的流体力学及传热性能的主要因素,回归得到了流体力学及传热的无因次准数关联式,为进一步研究此设备的干燥性能打下了基础。     

Fluidized Bed Air Drying: Experimental Study and Model Development

The presented study describes the processes and mechanisms of batch fluidized bed drying. The influencing factors of hot air drying are theoretically and experimentally examined, in order to present the relations between temperature and humidity profiles and all other drying parameters. A physical model is presented to facilitate the calculation of the drying processes under defined conditions. Three succeeding drying stages are therefore modeled. Mass and energy balances including all components taking part in the process are formulated. The model clarities the drying process under the assumption of pure heat transfer mechanisms. It does not contain adaptive parameters and takes into account an inactive bypass fraction of the fluidization and drying medium. The evaluation of the model was successful for two fluidized bed plants with nominal widths of 100 mm and 400 mm. The experiments showed sufficient accuracy and transferability of the model to equipment of application‐oriented dimensions.     

Particle‐scale simulation of the flow and heat transfer behaviors in fluidized bed with immersed tube

A kind of new modified computational fluid dynamics‐discrete element method (CFD‐DEM) method was founded by combining CFD based on unstructured mesh and DEM. The turbulent dense gas–solid two phase flow and the heat transfer in the equipment with complex geometry can be simulated by the programs based on the new method when the k‐ε turbulence model and the multiway coupling heat transfer model among particles, walls and gas were employed. The new CFD‐DEM coupling method that combining k‐ε turbulence model and heat transfer model, was employed to simulate the flow and the heat transfer behaviors in the fluidized bed with an immersed tube. The microscale mechanism of heat transfer in the fluidized bed was explored by the simulation results and the critical factors that influence the heat transfer between the tube and the bed were discussed. The profiles of average solids fraction and heat transfer coefficient between gas‐tube and particle‐tube around the tube were obtained and the influences of fluidization parameters such as gas velocity and particle diameter on the transfer coefficient were explored by simulations. The computational results agree well with the experiment, which shows that the new CFD‐DEM method is feasible and accurate for the simulation of complex gas–solid flow with heat transfer. And this will improve the farther simulation study of the gas–solid two phase flow with chemical reactions in the fluidized bed. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Demarcation of a new circulating turbulent fluidization regime

Transient flow behaviors in a novel circulating‐turbulent fluidized bed (C‐TFB) were investigated by a multifunctional optical fiber probe, that is capable of simultaneously measuring instantaneous local solids‐volume concentration, velocity and flux in gas‐solid two‐phase suspensions. Microflow behavior distinctions between the gas‐solid suspensions in a turbulent fluidized bed (TFB), conventional circulating fluidized bed (CFB), the bottom region of high‐density circulating fluidized bed (HDCFB), and the newly designed C‐TFB were also intensively studied. The experimental results show that particle‐particle interactions (collisions) dominate the motion of particles in the C‐TFB and TFB, totally different from the interaction mechanism between the gas and solid phases in the conventional CFB and the HDCFB, where the movements of particles are mainly controlled by the gas‐particle interactions (drag forces). In addition, turbulence intensity and frequency in the C‐TFB are significantly greater than those in the TFB at the same superficial gas velocity. As a result, the circulating‐turbulent fluidization is identified as a new flow regime, independent of turbulent fluidization, fast fluidization and dense suspension upflow. The gas‐solid flow in the C‐TFB has its inherent hydrodynamic characteristics, different from those in TFB, CFB and HDCFB reactors. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

柱形流化床传热特性的数值模拟

对Shedid等搭建的圆柱体流化床采用欧拉?欧拉法进行三维数值模拟,考察了颗粒球形度、表观进气速度和床料初始堆积高度对流化床内垂直加热壁面与流动床料之间对流传热特性的影响,采用有效导热系数分别计算气相和固相的对流传热系数。结果表明,随表观进气速度增大,流化床内颗粒物料湍流运动加剧,加热壁面平均温度和流体平均温度下降,壁面流体间传热平均温度差减小,壁面流体间对流传热系数增大;随初始床料高度增加,流化床内颗粒与加热壁面的接触面积增大,导致固相平均对流传热系数增大。     

振动流化床浸没水平管传热特性研究

为了深入研究振动流化床浸没水平管的传热特性,分别以沙子和玉米细颗粒作为实验物料,用水平探头测定了振动流化床中这2种床层颗粒与浸没水平管间的传热系数,分析了操作气速、振动频率、空气进口温度等因素对传热过程的影响。结果表明:在低气速下,振动是影响振动流化床中传热的主要因素,振动的引入可以明显改善流化作用,可以在低气速下得到较好的传热效果,同时达到节能的效果。通过分析实验结果,建立了振动流化床的传热关联式,模型计算值与实测值能较好吻合。研究结果可为干燥膏状物料时确定适宜的操作参数提供参考。     

Prediction of heat transfer to liquid-solid fluidized beds

Heat transfer coefficients to a liquid-solid fluidized bed in a cylindrical tube have been measured using water as liquid phase and three types of cylindrical steel particles, as well as glass, nickel, copper and lead spheres of different sizes as solid phase. The independent varaibles included heat flux, liquid velocity and particle physical properties. The experimental results as well as a data bank containing a large number of measured heat transfer coefficients for solid-liquid fluidization over a wide range of operational parameters have been compared with the predictions of most published correlations. A model for the prediction of heat transfer coefficients is proposed which predicts the present experimental data and the data of other investigators with good accuracy.     

SIMULATION OF FLUIDIZED-BED DRYING OF CARROT WITH MICROWAVE HEATING

ABSTRACT

A mathematical model of coupled heat and mass transfer was applied to batch fluidized-bed drying with microwave heating of a heat sensitive material—carrot. Four kinds of microwave heating with intermittent variation were examined. The numerical results show that different microwave heating patterns can affect the fluidized bed drying significantly. Changing the microwave input pattern from uniform to intermittent mode can prevent material from overheating under the same power density. Supplying more microwave energy at the beginning of drying can increase the utilization of microwave energy while keeping temperature low within the particle. For a particle diameter of 4 mm, fluidization velocity of 2 m/s, inlet airflow temperature of 70°C and the bed area factor of 80, the drying time are 750 and 1000 s, respectively, for the two good operating conditions with on/off periods of 125/375 s and 375/375 s. The cumulative microwave energy absorbed by particles at the end of drying is 1415 and 2300 kJ/kg (dry basis), respectively.     

湿污泥颗粒的流化床干燥实验及模型

在鼓泡流化床内以河砂为干燥介质,对单颗粒湿污泥的流态化干燥特性进行实验研究,得到了流化床温度、污泥初始水分、污泥粒径及流化速度对干燥速率的影响规律：流化床温度及污泥粒径对干燥速率的影响都呈指数规律;污泥的水分越大,干燥速率越大;在鼓泡流化床流化速度达到2倍临界流化速度以上时,充分流化,流化速度再增大(2~5倍临界流化速度)对干燥速率没有明显影响. 在基本的扩散传质理论的基础上,利用实验数据回归得到湿污泥在鼓泡流化床内干燥的半经验模型,为流化床污泥干燥器的设计提供了基础数据和依据.     

Fundamental particle fluidization behavior and handling of nano-particles in a rotating fluidized bed

The fluidization behavior of the three kinds of nano-particles (TiO₂, SiO₂, Al₂O₃) was analyzed in a rotating fluidized bed (RFB). Bed pressure drop, minimum fluidization velocity, bed expansion, entrainment and particle mixing characteristics under various centrifugal accelerations were experimentally investigated. The effects of centrifugal acceleration on agglomerate size and density were analyzed based on a Richardson-Zaki approach coupled with a fractal model.The bed pressure drop behavior showed almost similar to that of A or B-particles of Geldart's classification. Dimensionless particle bed height became smaller when the centrifugal acceleration was larger. Size of agglomerate decreased and its density increased with an increase in centrifugal acceleration. The agglomerate size in the RFB showed smaller than that in other types of fluidized bed system such as vibration and magnetic field as well as in a conventional fluidized bed, and the agglomerate density became larger. Particle entrainment became smaller in the case of the higher centrifugal acceleration. These results confirmed that the RFB can reduce the size of a nano-particle agglomerate and fluidize nano-particles at high gas velocity without any significant entrainment. The RFB is thus expected as more effective gas-solid fluidization system for handling of a large amount of nano-particles than other types of fluidized bed.     

EXPERIMENTAL RESEARCH ON MASS TRANSFER IN A CENTRIFUGAL FLUIDIZED BED DRYER

Abstract

The influences of bed thickness, particle diameter, rotating speed of the basket and operating gas velocity on the mass transfer between gas and particles in the centrifugal fluidized bed dryer (CFBD) were examined. The experimental correlation used to calculate the mass transfer coefficient in the centrifugal fluidized bed dryer was obtained.