Hydrodynamics of a spouted bed with a porous draft tube containing a small amount of finer particles

A small-size spouted bed with a porous draft tube was employed to obtain hydrodynamic data of binary mixtures of glass beads for a range of operating conditions and design factors. In this case, a small amount of finer particles was added mostly to the large majority of coarser particles. Under this condition, minimum spouting velocity, bed pressure drop, hold-up of solid particles within a draft tube, gas flow rate through the annulus and solids circulation rate were determined by changing the total gas flow rate and the mass fraction of finer particles as operating parameters, and by changing the height of the entrainment zone and the draft tube diameter as geometric parameters. The results show that the gas flow rate through the annulus increases by increasing the distance between the gas inlet nozzle and the bottom of the draft tube, that is, the height of the entrainment zone, but decreases with increasing draft tube diameter and mass fraction of finer particles. The porous draft tube shows a higher gas flow rate through the annulus than the non-porous draft tube, particularly in the case of the low height of the entrainment zone. The solids circulation rate increases with increasing gas velocity, the height of the entrainment zone and the porous draft tube diameter. Moreover, the porous draft tube leads to a higher solids circulation rate than the non-porous draft tube.     

双喷嘴矩形导流管喷动床喷动压降

引言 传统的柱锥形喷动床(CSBs)的应用受到一些因素的限制,例如处理物料能力、起始压力大及难以放大等,为此,Romankov等[1]最早提出了长方形截面的矩形喷动床结构,来克服CSBs的缺点.此后,Rocha等[2]用矩形喷动床进行了片剂包衣的研究.     

Effects of Draft Tubes on Particle Velocity Profiles in Spouted Beds

The vertical particle velocity profiles in a full‐column cylindrical conical spouted bed, with or without a draft tube, are measured using a fibre optic probe system. The profiles have different characteristics for a draft tube spouted bed (DTSB) than for a conventional spouted bed (CSB). The spout of a CSB consists of a central flow where particle velocities fit exponential distributions, and a boundary layer where particle velocities are nearly uniform. The spout of a DTSB has no boundary layer and its radial particle velocity profiles are approximately linear. The particle velocities in the spout of a DTSB increase when superficial gas velocity increases, draft tube diameter decreases, or when entrainment height decreases. A kinematic model has been used to simulate the granular flow in the annulus of a CSB and DTSB, and they are compared with the experiments. The particle velocities in the annulus of a DTSB are much lower than that of a CSB. Their radial profiles are also different with a CSB. The dependence of particle velocities in the annulus of a DTSB on superficial gas velocity, draft tube diameter, and entrainment height are also discussed. One concludes that the draft tube diameter and entrainment height are two key factors for the solid circulation rate of a DTSB.     

Hydrodynamic simulations of gas–solid spouted bed with a draft tube

Flow behavior of particles in a two-dimensional spouted bed with a draft tube is studied using a continuous kinetic-friction stresses model. The kinetic stress of particles is predicted from kinetic theory of granular flow, while the friction stress is computed from a model proposed by Johnson et al. (1990). A stitching function is used to smooth from the rapid shearing viscous regime to the slow shearing plastic regime. The distributions of concentration and velocities of particles are predicted in the spouted bed with a draft tube. Simulated results compare with the vertical velocity of particles (Zhao et al., 2008) measured and in the spout bed with draft plates and solid circulation rate (Ishikura et al., 2003) measured in the spouted bed with a draft tube. The impact of the friction stress of particles on the spout, annulus, fountain and entrancement regions is analyzed in gas–solid spouted bed with a draft tube. Numerical results show that the gas flow rate through the annulus increases with the increase of the entrainment zone. The solids circulation rate decreases with the decrease of inlet gas velocity and the height of the entrainment zone. The effect of spouting gas velocity on distributions of concentration, velocity and particle circulation is discussed.     

导向管直径对喷动床流动特性影响的计算颗粒流体力学数值模拟

导向管喷动床是较为常见的一种喷动床改进床型,通过阻断喷动区与环隙区气固接触来提高颗粒循环的规律性与稳定性。本文采用计算颗粒流体力学（CPFD）方法对于直径150mm的柱锥式导向管喷动床进行了数值模拟研究,考察了导向管直径对于喷动床内颗粒流动特性的影响,从环隙区死区分布、颗粒速度分布、固体循环量等方面分析了具有不同直径导向管喷动床的运行状态。结果表明,加入导向管在减少床内死区的同时也降低了运行时的固体循环量,对于本次采用的喷动床结构尺寸与运行参数,只有在导向管直径为40～60mm时才能保证床内具有良好喷动状态,综合考虑各因素,选用直径50～55mm的导向管最为合适。对于具有类似结构与运行条件的柱锥喷动床,导向管直径可考虑选为无导向管运行时喷动区直径的1.2～1.375倍。     

CFD simulation of gas–solid flow in a spouted bed with a non-porous draft tube

A multi-fluid Eulerian–Eulerian approach incorporating the kinetic theory of granular flow was used to simulate a spouted bed containing non-porous draft tube. Drag function and coefficient of restitution were investigated. Solid and gas velocity vector, gas flow rate in annulus and spout regions and longitudinal pressure distribution were evaluated. In addition, the effects of the entrainment height and the draft tube diameter were studied. Simulation indicates the formation of three regions namely, annulus, spout and fountain; similar to a conventional spouted bed. Current model predicts acceptable results in both spout and annulus regions. Simulation results indicate that the model can be employed for both mono-size and multi-size particles reasonably. This paper provides useful basis for further works on understanding gas–solid flow mechanism in spouted beds containing a non-porous draft tube.     

Drying characteristics of a draft tube spouted bed

Using the results of earlier work on the flow pattern of gas and solids in a draft-tube spouted bed, the drying characteristics of such a spouted bed are discussed. Paddy (unpeeled rice) was dried in a 30 cm bed with a 5.5 cm draft tube and temperatures and moisture content of solid and gas phase were measured as a function of drying time at various points in the system. It appears that the (constant) drying rate is determined by the heat transfer in the recirculation zone (just above the air inlet) and in the draft tube. After the short and rapid heating in the tube, the temperature and moisture gradients in the particle equilibrate in the annulus. It is concluded that a draft-tube spouted bed is a promising dryer design for heat-sensitive particles with slow intra-particle mass transfer coefficients.     

Hydrodynamics of a spouted bed with an impermeable draft tube for binary particle systems

A spouted bed with an impermeable draft tube was employed to obtain fundamental data of binary mixtures of glass beads for both the operating conditions and the design factors. These data were compared with those for the coarser particle system only. From this view point, minimum spouting velocity, pressure drop, hold-up of solid particles within a draft tube, upward gas flow rate within the annulus and solids circulation rate were determined by changing the total gas flow rate and mass fraction of finer particles as operating parameters and by changing distance of entrainment zone and draft tube diameter as geometric parameters.     

超细粉在导向管喷动床中的固体循环速率

Ultra-fine powders are difficult to be fluidized due to the strong particle to particle cohesiveness.However, the authors‘ experiments showed that the ultra-fine powder CaCO3 could be stably fluidized in a spouted bed with a draft tube. The effects of geometric and operating parameters on solid circulation rate of ultra-fine powder CaCO3 were investigated in a 120 mm diameter transparent semicircular spouted bed with a draft tube. Three draft tubes with different sizes were used in this study. It was found that the solids circulation rate was mainly dependent on the drawing rate of the gas jet from the nozzle, then on the gas transport capacity in the draft tube. With increasing gas feed rate, distance between the nozzle and the draft tube inlet and draft tube diameter, the solids circulation rate could be increased. Based on the jet theory, a quantitative correlation was proposed for predicting the solid circulation rate of ultra-fine powders in a spouted bed with a draft tube by taking into account the gas transport capacity in the draft tube.     

A Draft-Tube Conical Spouted Bed for Drying Fine Particles

A study has been conducted on the performance of a draft tube conical spouted bed for drying fine particles. Batch operation has been performed with nonporous, porous, and open-sided draft tubes in order to ascertain the optimum configuration of this internal device. The nonporous draft tube requires the lowest minimum spouting velocity. Nevertheless, the solid circulation rate and the drying efficiency of the open-sided draft tube are superior to any other spouted bed configuration. Moreover, it allows for reducing the height of the fountain and, consequently, the height of the drying equipment.     

A Draft-Tube Conical Spouted Bed for Drying Fine Particles

A study has been conducted on the performance of a draft tube conical spouted bed for drying fine particles. Batch operation has been performed with nonporous, porous, and open-sided draft tubes in order to ascertain the optimum configuration of this internal device. The nonporous draft tube requires the lowest minimum spouting velocity. Nevertheless, the solid circulation rate and the drying efficiency of the open-sided draft tube are superior to any other spouted bed configuration. Moreover, it allows for reducing the height of the fountain and, consequently, the height of the drying equipment.     

导向喷动流化床颗粒物料抛高的估算

本文以气固两相流运动理论为基础，进行导向喷动流化床颗粒物料抛高估算，从而确定导向喷动流化床床高。计算结果与实验测定值吻合颇好。     

Simulations of flow behavior of gas and particles in spouted bed with a porous draft tube

Flow behaviors of particles in a two-dimensional spouted bed with a porous draft plates are studied using a fluid dynamic computation with kinetic-frictional stresses models. Gas flow through the porous draft tube is simulated by Brinkman-Darcy-Forchheimer formulation. The distributions of concentration and velocities of particles are predicted. Simulated results predict the solid circulation rate and gas flux rate measured in the spouted bed with a porous draft tube (Ishikura et al., 2003). The solid circulation rate in the spouted bed with a porous draft tube is larger than that with a non-porous draft tube. The predicted bed pressure drop with the porous draft tube is high in comparison to the spouted bed with non-porous draft tube. The effect of the porosity of the porous draft tube on distributions of gas flux rate through the annulus and solid circulation rate are discussed.     

Effect of operating conditions on the drying of fine and ultrafine sand in a fountain confined conical spouted bed

Abstract

A study has been carried out on the influence process conditions and design parameters have on the drying in a conical spouted bed. Optimum parameters have been determined for the draft tube and the fountain confiner. Drying time is reduced when the spout region is enlarged. A distance between the bed surface and the lower end of the confiner in the 0.10–0.15 m range and a confiner of 0.5–0.9 m length minimize the drying time. Longer distances do not avoid entrainment, and shorter distances lead to higher pressure drop and minimum spouting velocity. Longer fountain confiners do not reduce significantly the drying time. Draft tubes with a reduced aperture ratio lead to longer drying times due to their adverse effect on the gas–solid contact. Aperture ratios above 60% cause a decrease in the efficiency of the process due to the higher gas flow rates required to achieve spouting regime.     

导向管喷动流化床的喷动气旁路分率

在内径为182 mm的喷动流化床中安装内径80 mm的导向管,以平均粒径为2.2 mm的尿素颗粒为物料,对喷动气旁路特性进行了实验研究,分别考察了夹带区高度、导向管长度、喷嘴内径、床层高度、喷动气速和流化气速对喷动气旁路分率的影响,结果表明随着喷动气速的增大,喷动气体旁路分率先增后减。导向管安装高度越高,气体旁路分率越大。床层高度增大喷动气体旁路分率略有降低。而喷嘴直径小于50 mm时气体旁路分率随喷嘴直径增大而提高,在大于50 mm时气体旁路分率随喷嘴直径增大维持不变。当气速较小时,导向管高度增大会引起气体旁路分率增大,引入少量流化气能有效地抑制喷动气旁路。     

Solid circulation and gas bypassing in an internally circulating fluidized bed with an orifice-type draft Tube

The effects of orifice diameter in the draft tube, particle size, gas velocities and bed height on the circulation rate of solids and gas bypassing between the draft tube and annulus have been determined in an internally circulating fluidized bed (i.d., 0.3 m ; height, 2.5 m) with an orifice-type draft tube. A conical shape gas separator has been employed above the draft tube to facilitate the separation of gases from the two beds. The circulation rate of solids and the quantity of gas bypass from the annulus to draft tube show their minimums when the static bed height is around the bottom of the separator. The circulation rate of solids increases with an increase in orifice diameter in the draft tube. At fixed aeration to the annulus, gas bypassing from the draft tube to annulus sections decreases, whereas reverse gas bypassing from the annulus to the draft tube increases with increasing the inlet gas velocity to the draft tube. The obtained solids circulation rate has been correlated by a relationship developed for the cocurrent flow of gas and solid through the orifice.     

双喷嘴矩形喷动床流动性能实验研究

在120 mm×240 mm的双喷嘴矩形不锈钢床内,对新型双喷嘴矩形导流管喷动床的最小喷动速度和喷动高度进行了研究,考察了喷动气速、粒径、静床层高度、导流管直径、导流管安装位置对最小喷动速度和喷动高度的影响。结果表明:最小喷动速度随颗粒直径、导流管直径、导喷距的增大而增大,随静床层高度的增大而减小;喷动高度随喷动气速的增大而增大,随导流管直径的增大而减小,受静床层高度和导喷距的影响不大,并得出了最小喷动速度的关联式。     

使用导流管对连续喷动干燥器的影响

在欧洲市场,对使用诸如团块状的生物质燃料的关注日益增长。本文给出了使用带有不同类型导流管的连续喷动干燥锯末的实验数据。对不同进口和出口温度下湿锯末干燥进行了研究。在喷动干燥器中,干燥能力取决于热流量大小。实验结果表明,导流管能够提高干燥能力。此外,导流管的设计对热流量利用有影响。     

Bed density and circulation mass flowrate in a novel annulus-lifted gas–solid air loop reactor

Air loop reactors (ALR) have been widely used as promising and high-efficiency gas–liquid and gas–liquid–solid reactors. Extensive research on ALR has been conducted, but mostly limited to gas–liquid and gas–liquid–solid systems. Work associated with gas–solid systems has been rare and mainly focused on draft tube-lifted spouted bed treating coarse Geldart B, D particles. The present paper proposed a novel gas–solid air-loop reactor treating fine Geldart A particles and operating in a new annulus-lifted mode, with bubbling or turbulent bed upward flow in the annulus in parallel with bubbling bed downward flow in the draft tube. In view of these differences, distinct hydrodynamic behaviour can be anticipated for the gas–solid annulus-lifted air-loop reactor. The influence of operating conditions and geometric configuration on the distribution of bed density is discussed in a cold model annulus-lifted air loop reactor. A mechanistic model for the circulation mass flowrate is established based on an energy balance and resistance analysis. Nearly 50% and 30% of the energy dissipation rate occurs in the bottom and top regions, respectively. With increasing draft tube height, the energy dissipation rate increases in the annulus and draft tube regions, while it decreases in the top and bottom regions. The circulation mass flowrate decreases with increasing draft tube height. Analysis of the distribution of bed density and energy dissipation rate leads to suggestions regarding optimization of the design and axial location of the ring distributor and gap height.     

Drying of Biomass in a Conical Spouted Bed with Different Types of Internal Devices

The drying of sawdust was studied in a conical spouted bed pilot plant in order to adapt this feed for the pyrolysis process. Air at different temperatures was used and the effect of sawdust particle size and operating gas velocity was studied. Batch operation was performed with no internal device and with nonporous and open-sided draft tubes in order to ascertain the optimum configuration of the contactor. Although the nonporous draft tube required the lowest minimum spouting velocity, its performance was poor due to deficient gas–solid contact. Configurations with open-sided draft tubes and with no internal devices had higher efficiencies because of their better contacts. An increase in air temperature resulted in a reduction in drying time but the operating conditions need to be fine-tuned to ensure proper energy efficiency.