Effect of three drying methods on the drying characteristics and quality of okra

The objective of this study was to compare the drying characteristics and quality of dried okra obtained by vacuum freeze drying (VFD), microwave vacuum drying (MVD), and pulse-spouted microwave vacuum drying (PSMVD). The quality parameters include color (L*, a*, and b*), texture (hardness and fracturability), shrinkage ratio (SR), nutrient retention (chlorophyll, flavonoids, and vitamin C), and sensory score was investigated. Vacuum freeze drying maximally preserved the original properties of samples. And the samples dried by PSMVD showed higher quality and more uniformity compared to MVD. Considering of all aspects comprehensively, such as cost-effectiveness, practicability, and scale-up, PSMVD was a promising technique which would match results obtained by vacuum freeze drying.     

Effects of Different Drying Methods on the Quality Changes of Granular Edamame

In this article, the quality changes of the granular fruits and vegetables dried by vacuum microwave drying, freeze drying, hot air drying, and combined hot air–vacuum microwave drying are investigated, and the quality parameters compared on the basis of vitamin C and chlorophyll contents, shrinkage and rehydration capacity, color, texture, and microstructure changes. The quality parameters of products dried by vacuum microwave drying are slightly lower than those obtained by freeze drying, but much better than those obtained using conventional hot air drying. The quality characteristics of product dried by combined hot air–vacuum microwave are significantly improved compared to those simply hot air–dried.     

纳米粉体干燥方法的研究进展

由于纳米粒子的表面效应，用湿法制备出的纳米粉体的前驱——胶体的干燥已不能采用传统的干燥方法。根据胶体干燥的理论，阐述了纳米粉体干燥过程的团聚机理，并综述了纳米粉体在超临界干燥、共沸蒸馏、真空冷冻干燥、微波干燥等干燥领域的研究进展。     

A Combination of Freeze Drying and Microwave Vacuum Drying of Duck Egg White Protein Powders

High energy consumption during freeze drying (FD) is a major concern that limits its application on common food product manufacturing. In this research, fresh duck egg white protein (FDEWP) powder and desalted duck egg white protein (DDEWP) powder were obtained by a combined two-stage tandem drying technologies (FD and microwave–vacuum drying [MVD]) in order to reduce energy consumption while maintaining good product quality. The results showed that the drying time for the FDEWP and DDEWP powders was significantly decreased by FD + MVD compared to those obtained by the FD-only process. The FDEWP powders dried by FD + MVD had a better color (higher L* and lower b*), lower apparent density, and lower foaming stability but higher emulsifying index than those dried by FD only. The DDEWP powder dried by FD + MVD had a product quality similar to that of FDEWP powder, suggesting that the DDEWP powder could be widely used as a food ingredient.     

干燥方法对化学沉淀法合成HA粉体团聚的影响

化学沉淀法合成羟基磷灰石粉体工艺简单,成本低廉,但这种方法得到的羟基磷灰石粉体极易团聚,限制了羟基磷灰石的广泛使用.本文研究了在羟基磷灰石粉体的合成过程中不同干燥方法对粉体团聚的影响.结果表明:在烘箱干燥得到的粉体团聚较严重,微波干燥使粉体的团聚程度有所减轻,冷冻干燥可有效地减弱粉体的团聚,所得到的粉体比表面积较高.同时,本文还讨论了粉体在干燥过程中团聚形成的机理.     

Effects of Different Drying Methods on the Quality Changes of Granular Edamame

In this article, the quality changes of the granular fruits and vegetables dried by vacuum microwave drying, freeze drying, hot air drying, and combined hot air-vacuum microwave drying are investigated, and the quality parameters compared on the basis of vitamin C and chlorophyll contents, shrinkage and rehydration capacity, color, texture, and microstructure changes. The quality parameters of products dried by vacuum microwave drying are slightly lower than those obtained by freeze drying, but much better than those obtained using conventional hot air drying. The quality characteristics of product dried by combined hot air-vacuum microwave are significantly improved compared to those simply hot air-dried.     

Quality evaluation of Panax notoginseng extract dried by different drying methods

Quality control still remains a big issue, affecting herbs, formulations, and even the practice of Traditional Chinese Medicine. A promising solution to the problem is to take advantage of innovative process techniques including alternative drying methods within the pharmaceutical processing. Nowadays, vacuum belt drying (VBD) has gained more and more importance in food and pharmaceutical processing. In this work, Panax notoginseng extract was made into powder by the gentle VBD as well as by classical spray drying (SD), freeze drying (FD), and vacuum drying (VD). Certain chemical and physical properties of the dried powders such as moisture content, drying time, porosity, density, saponins content, pH value and hydroxyl radicals scavenging activity were evaluated. The results showed the qualities of dried products were influenced to different extent by drying methods certainly. Vacuum belt drying was suggested to dry P. notoginseng extract for its high quality assurance of hygroscopic products and suitable for sticky or high viscous products.     

干燥方式对红枣动力学及挥发性成分的影响

采用热风干燥、真空冷冻干燥和微波真空干燥对红枣进行干燥处理，结合顶空固相微萃取-气相色谱-质谱（headspace solid-phase microextraction-gas chromatography-mass spectrometry，HS-SPME-GC-MS）和电子鼻对枣片挥发性成分进行了分析，并对比了3种干燥方式对红枣色泽、动力学和挥发性成分的影响。结果表明，热风干燥和微波真空干燥对枣片色泽影响较大，真空冷冻干燥能够更好的保持原始色泽；对动力学方程进行拟合，发现Page 模型为预测红枣3种干燥方式干燥特性最适合的数学模型；干燥对枣片挥发性成分种类及相对含量差异显著，其中干燥前后相同的挥发性成分有19种。挥发性物质主要有酸类、酯类、醇类、醛类、酮类、烃类、杂环类和其他化合物，干燥过后枣片中酸类和烷烃类挥发性成分相对含量显著增加，醛类和杂环类物质显著降低。电子鼻结果表明干燥后枣片香气特征与新鲜红枣有较大的区别，热风干燥和微波真空干燥香味特征较为接近，微波真空干燥枣片的焦甜香特征更为明显。相较于热风干燥和真空冷冻干燥，微波真空干燥效率较高、能耗较低、周期较短，更适于制备干燥枣片。     

Drying Characteristics and Quality of Restructured Wild Cabbage Chips Processed Using Different Drying Methods

The drying characteristics of restructured wild cabbage chips dried using microwave vacuum (MVD), hot air (AD), and microwave freeze drying (MFD) were compared. Some of the key quality parameters of restructured wild cabbage chips such as fracturability and color and sensory characteristics were measured. Results showed that the drying time was reduced with the increase of microwave power (MVD/MFD) and in the case of air drying by the temperature (AD). Drying time was the shortest in the MVD process. Optimal quality of dried chips was obtained with the MFD process at a microwave power level 2.0 W/g.     

Freeze Drying of Apple Slices with and without Application of Microwaves

In this study, Fuji apple slices were dehydrated using freeze drying (FD) combined with microwave assisted with vacuum drying (VMD). The optimal parameter for the diversion point of moisture content from FD to VMD process was at the moisture level of 21%, and for VMD the optimal parameter for vacuum pressure was at 9.15 kPa and microwave power density was at a level of 3.18 w/g. The results show that the two-step technique can significantly reduce total FD time required by up to 40%, while the nutritional value of the dried apple chips remained unchanged compared to FD used alone.     

Drying kinetics and product quality of green soybean under different microwave drying methods

The objective of this study was to investigate the effect of different microwave drying techniques on the drying kinetics and product quality of dried green soybean. Experiments were conducted using microwave vacuum drying (MVD), pulse-spouted vacuum microwave drying (PSMVD), pulse-spouted microwave drying (PSMD), and microwave freeze drying (MFD). Parameters of apparent density, color, processing temperature, expansion ratio, rehydration ratio, texture, and microstructure of the dried products were determined. The results showed that the MFD green soybean had a small change on bright color, compared with the fresh samples, but the drying time was the longest among the four methods. The bright color value of PSMVD/PSMD/MVD, respectively, was 79.77, 71.43, and 55.45, and drying time of them was slightly different. The PSMVD/PSMD showed advantages over MVD by improving the product quality.     

Effects of different drying methods on the extraction rate and qualities of oils from demucilaged flaxseed

Effects of different drying methods, i.e., oven drying, freeze drying, vacuum drying, and microwave drying, on the extraction rate and qualities of oil extracted from demucilaged flaxseed were investigated. The results show that microwave drying and freeze drying have higher extraction rate and yield (46.36 and 46.16% vs. 33.90%) of oil compared with native flaxseed. The oil extracted from dried flaxseed, especially the one freeze dried, had higher peroxide value (21.63 vs. 6.15?meq/kg) and specific ultraviolet extinction at 232?nm (4.56 vs. 3.67) and 268?nm (1.23 vs. 1.12), as well as a shorter induction time (1.8 vs. 3.3?h) than the one from native sample. Demucilaging and drying have no significant effect on fatty acid composition of flaxseed oil. However, these processes increased the content of total phenols and total sterols while reduced the content of chlorophyll and carotenoid pigment. In addition, the oil extracted from vacuum dried flaxseed contained more tocols when compared with native sample (447.29 vs. 370.99?mg/kg).     

Microwave,Vacuum, and Air Drying Characteristics of Collard Leaves

Collard leaves (Brassica oleracea L. var. acephala) with an initial moisture content of 6.65 on percentage dry basis (%db) were dried by three different drying methods: microwave, air, and vacuum. Samples of fresh leaves, 25 g each, were dried until their moisture was down to 0.1 on a dry basis. The following drying levels were used in each of the drying processes: 350, 500, 650, 750, 850, and 1000 W for microwave drying; 50, 75, 100, 125, 150, and 175°C for air drying; and 0.4, 50, and 100 mmHg at 50 and 75°C for vacuum drying, respectively. Drying times ranged between 2.5 to 7.5 min, 8 to 210 min, and 35 to 195 min for microwave, air, and vacuum drying, respectively. The data obtained compared well with a thin-layer drying model. Microwave drying at 750 W provided optimal results with respect to drying time, color, and ascorbic acid content (vitamin C).     

A comparative study on hygroscopic and physiochemical properties of chicken powders obtained by different drying methods

Abstract

Different drying methods (spray drying (SD), vacuum drying (VD), microwave vacuum drying (MVD), and infrared vacuum drying (IFVD)) were applied in order to compare the hygroscopicity behavior of chicken powders. The hygroscopicity curves and glass transition temperature were used to evaluate the influence of ambient humidity and temperature on moisture absorption of powders. The results showed that the chicken powder dried by MVD had the lowest moisture absorption, followed by IFVD, VD, and SD. The hygroscopicity of SD chicken powders was different from other three kinds of chicken powders due to the physical properties of particles and the changes of protein secondary structure as detected by the Fourier transform-infrared spectrometer. For the three vacuum drying methods, the difference of protein secondary structure was the main reason of differences in hygroscopicity. Although MVD chicken powders were slightly inferior to SD chicken powders in taste, MVD chicken powders were the best in terms of smell and color as suggested by instrumental sensory parameter evaluations. It was found that MVD had a positive effect on reducing moisture absorption and maintaining sensory quality of chicken powders.     

介电材料辅助的微波冷冻干燥的实验研究

设计、加工和装配了一套实验室规模的微波冷冻干燥装置,旨在实验验证介电材料对微波冷冻干燥液体物料的强化作用。介电材料用烧结的碳化硅(SiC),石英玻璃作为介电材料的参照物;甘露醇,一种典型的药物赋形剂被选为待干溶液中的溶质。实验结果表明使用介电材料可以有效地强化微波冷冻干燥过程。与传统冷冻干燥相比干燥速率大大加快,在试验条件下干燥时间可以节省20%。微波加热逐渐生效并且主要体现在干燥过程的后半部分。当溶液中的固含量很低或者固体物质具有很小的介电损耗因子时,如果不用介电材料,微波加热的效果不明显。     

Dehydration of Concentrated Ganoderma lucidum Extraction by Combined Microwave-Vacuum and Conventional Vacuum Drying

Combination of microwave-vacuum drying and conventional vacuum drying was investigated as a potential method for drying concentrated Ganoderma lucidum extraction. The Ganoderma lucidum was extracted by hot water (60–65°C) and then concentrated to moisture of about 70% (wet basis) in a rising-film evaporator. The concentrated sample was dried by microwave-vacuum until the moisture content reached 10% (wet basis), and then by conventional vacuum drying at the temperature of 55–60°C to final moisture content about 6% (wet basis). The retention of polysaccharide and triterpenes of Ganoderma lucidum dried by this method were evaluated and compared with those dried by freeze drying and conventional vacuum drying alone. The comparison showed that the quality of extraction dried by the current method was close to that of freeze-dried extraction and much better than that of conventional vacuum-dried ones.     

黑加仑真空冷冻与微波真空联合干燥工艺研究

以黑加仑为原料,对其进行了真空冷冻与微波真空联合干燥工艺的研究。结果表明：先真空冷冻后微波真空干燥（FDMV）的组合方式是可行的;联合干燥合理工艺参数为：微波功率1．34kW。绝对压力11kPa,转换含水率为20％（wb）;通过试验验证,联合干燥生产的脱水黑加仑的感官品质和营养成分接近真空冷冻干燥,联合干燥方式对节省干燥时间和降低能耗是有效的。     

Optimal Control of the Secondary Drying Stage of Freeze Drying of Solutions in Vials Using Variational Calculus

Abstract:

The problem of operating freeze drying of pharmaceutical products in vials loaded on trays of freeze dryer to obtain a desired final bound water content in minimum time is formulated as an optimal control problem. Two different types of freeze dryer designs were considered. In the type I freeze dryer design, upper and lower plate temperatures were controlled together, while in the type II freeze dryer design, upper and lower plate temperatures were controlled independently. The heat input to the material being dried and the drying chamber pressure were considered as control variables. Only the scorch temperature was considered as a constraint on the system state variables during the secondary drying stage, because all the free water content (frozen water) is removed from the solid matrix during the primary drying stage of freeze drying. Necessary conditions of optimality for the secondary drying stage of freeze drying process in vials were derived and presented by using rigorous multidimensional unsteady-state mathematical models. The theoretical approach presented in this work was applied in the freeze drying of skim milk. Significant reductions in drying times of the secondary drying stage of the freeze drying process in vials were observed and more uniform bound water and temperature distributions in the material being dried were obtained compared to the conventional operational policies.     

掺锑氧化锡纳米晶体的制备及性能研究

以SnCl4.5H2O和SbCl3乙醇溶液为原料,用离子交换除氯水解法制备得到无氯离子的前驱体掺锑氢氧化锡胶体沉淀。采用了乙酸异戊酯有机溶剂作脱水剂以消除掺锑氢氧化锡胶体干燥过程中硬团聚的形成,并和常用的正丁醇共沸溶剂进行了粉体性能的比较。用BET、XRD和TEM等方法对前驱体和掺锑氧化锡纳米粉体进行表征。结果表明,乙酸异戊酯溶剂比正丁醇溶剂更有效防止了粉体干燥过程中硬团聚的形成;将乙酸异戊酯干燥所得掺锑氢氧化锡干粉经热处理后得到了高比表面积的掺锑氧化锡纳米粉体,并对晶粒的生长过程进行了研究。     

The Effects of Predrying Treatments and Different Drying Methods on Phytochemical Compound Retention and Drying Characteristics of Moringa Leaves (Moringa oleifera Lam.)

The most appropriate maturity stage of Moringa oleifera leaves was selected for drying based on phytochemical content, including quercetin and kaempferol. Desorption isotherms were developed and were best fit by the modified Henderson model. Prior to drying, samples were left untreated, blanched in boiling water, and blanched in NaHCO₃/MgO. The leaves were dried by hot air tray drying (TD) and heat pump–dehumidified drying air (HPD) at air temperatures of 40, 50, and 60°C. Alternatively, leaves were subject to microwave drying (MWD) at 150, 450, and 900 W and to freeze drying (FD). The moisture versus time data were fitted to five drying models. In general, a three-parameter model gave the best fit. The drying constant was related to the drying temperature or microwave power using an Arrhenius model. Effective moisture diffusivity (D _eff) increased with higher drying temperature, higher microwave power, or blanching treatments. Structural changes in the leaves after drying and upon rehydration were observed by scanning electron microscopy (SEM). Leaves blanched and dried using HPD at 50°C and fresh and dried using FD showed a partial breakdown of the tissue structure upon rehydration. HPD and blanching reduced the drying time by 8.3% and increased quercetin and kaempferol levels by 42.1 and 51.4%, respectively, compared to TD at 50°C. MWD provided the quickest drying followed by HPD and TD, respectively. HPD drying of M. oleifera after blanching resulted in relatively greater quality compared to TD and MWD.