QUALITY INTERACTION IN A JET SPOUTED BED DRYER FOR BIO-PRODUCTS

An experimental study was conducted to apply the jet spouted bed (JSB) dryer with inert bodies for drying of fodder antibiotic; (zinc-salt bacitracin and tylosin) and baker's yeast which are extracted from fermentation broth. After establishing the drving properties of these products (e.g. sorption isotherm, water activity and thermostability), the influence of basic drying parameters (temperature of drying agent, bed loading, gas flow rate) on drying characteristics and quality of the products was determined. The results proved that a JSB dryer may be successfully applied to fodder antibiotics; especially to Zn-bacitracin; however, for a highly labile live organism like baker's yeast, this method cannot be used. The optimal parameters for drying of Zn-bacitracin have been presented.     

HYDRODYNAMICS AND MASS TRANSFER IN A SPOUTED BED DRYER

ABSTRACT

The disposal of sludge generated by water treatment plants poses major financial and environmental problems. Drying of the sludge is an essential pan of any disposal process which may include incinerating, landfilling or upgrading. In the present study, experiments were carried out to investigate the drying of sludge in a spouted bed and to characterize the hydrodynamics and mass transfer mechanisms. The effect of bed moisture content on the minimum spouting velocity (U_ms) was examined for sludge granules. U_ms was found to increase with increasing the moisture content of the sludge particles. The gas phase mass transfer coefficient in the dryer was determined using porous calcined alumina particles and the results were compared with predictions by correlations available in the literature. The existing correlations gave poor predictions for the mass transfer coefficient. A new correlation for the mass transfer coefficient in a spouted bed dryer was developed based on the experimental results.     

PERFORMANCE EVALUATION OF A CONVENTIONAL NAUTAMIXER APPLIED AS A DIRECT DRYER

This paper describes the experiments which were conducted with the objective to determine the potential of a conventional Nautamixer applied as a direct dryer. This convective Nautamixer-dryer was used for drying the urea nitrate containing around 15% of water, which is converted from a pasteous form into a powder of a moisture lewel below 1%.

The influence of the following variables was studied: increased hot air velocity and temperature, number of revolutions of the agitator, and mass of the drying material. The effect of inlet air distribution to the periphery of the bed of the material was studied with a perforated plate distributor by blanking the holes (17%). which adversely affected the drying rate. The examination of the effect of external heating through the wall indicated that it is not possible to achieve the desired moisture level of the product without the introducing the flowing hot air. As an addition to the convective drying the indirect drying contributed more to the increase of the outlet air temperature than to the increase of the drying rate. As expected, shorter drying time is obtained with higher air flow rates and temperatures as well as with increased number of revolutions of both the orbital arm and the mixing screw.     

EXPERIMENTAL ANALYSIS OF A MECHANICALLY STIRRED SPOUTED BED DRYER

ABSTRACT

In order to increase the movement of the particles in the annular region of a conical spouted bed, a mechanical stirrer was incorporated. This led to a study of the fluid dynamics of the conical spouted bed of inert particles under different operating conditions: mass of inert particles, ratio of inert particles to suspension volumes, type of stirrer (2 designs) and stirrer speed.

The action of the stirrers resulted in increased movement of the particles, especially at low rpm values (≤ 90 rpm), with the loss of the annular region, and thus approaching the beds behavior to that of a fluidized bed. To characterize this novel type of spouted beds, the “minimum spouting flow” (Q_ms) parameter which is used usually was replaced by the “minimum pseudo-fluidizing flow” (Qmpr). The value of Q_mpf decreases when the agitation in the bed increases. A correlation for Q_mpf with the different operating conditions was developed.

Drying suspensions in the stirred spouted bed shows a considerable increase of drying capacity, over units without agitation.     

DRYING OF HIGH MOISTURE CONTENT PADDY IN A PILOT SCALE TRIANGULAR SPOUTED BED DRYER

From the successful drying of paddy in a lab-scale triangular spouted bed (TSB), a pilot scale unit with a capacity of 500kg/batch was constructed and used to dry paddy of high moisture contents. The drying tests showed that air temperatures of up to 160°C in the first stage, followed by a lower temperature of 80-100°C in the second stage, can be used to dry paddy from more than 25% down to around 15% (w.b.) without significantly changing grain quality in terms of head rice recovery. Moisture distribution in the pilot-scale TSB was observed to be satisfactorily uniform.     

RADIO FREQUENCY ENHANCED DRAUGHT TUBE SPOUTED BED DRYER

ABSTRACT

A study of the operation of a draught tube spouted bed in conjunction with dielectric heat addition was carried out. The addition of radio frequency allowed a greater amount of energy to be input into the particulate material in any given time, increasing the drying rate: however, the drying pattern was unaffected by the ratio of radio frequency to convective heat addition. The rate of moisture loss was proportional only to the total energy input. The synergy which often occurs with low levels of radio frequency addition does not occur with rf enhanced spouted beds.

The properties of spouted beds seem to be improved only for moisture contents at which packed bed drying can perform effectively.

Although the properties of spouted beds can be improved by radio frequency heat addition, their qualities although useful for specific operations, are unsuitable for more general use.     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

HYDRODYNAMICS AND MASS TRANSFER IN A SPOUTED BED DRYER

The disposal of sludge generated by water treatment plants poses major financial and environmental problems. Drying of the sludge is an essential pan of any disposal process which may include incinerating, landfilling or upgrading. In the present study, experiments were carried out to investigate the drying of sludge in a spouted bed and to characterize the hydrodynamics and mass transfer mechanisms. The effect of bed moisture content on the minimum spouting velocity (U_ms) was examined for sludge granules. U_ms was found to increase with increasing the moisture content of the sludge particles. The gas phase mass transfer coefficient in the dryer was determined using porous calcined alumina particles and the results were compared with predictions by correlations available in the literature. The existing correlations gave poor predictions for the mass transfer coefficient. A new correlation for the mass transfer coefficient in a spouted bed dryer was developed based on the experimental results.     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

ABSTRACT

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

BATCH VIBRATING FLUID BED DRYER FOR SAWDUST PARTICLES: EXPERIMENTAL RESULTS

ABSTRACT

In a batch experimental equipment, the behavior of a sawdust dryer in a vibrating fluidized bed is analyzed. Empirical data concerning fluidization velocities, pressure drops and drying kinetics was obtained, and advantages of using vibration in the drying chamber, relative to a conventional fluidized bed, are shown. This technique is presented as an alternative to solve problems of solid agglomeration and bed defluidization. Results show that it is possible to dry sawdust with more than 2 kg/kg moisture, in a vibrating bed keeping a high degree of bed homogeneity and high quality of fluidized state.     

EFFECT OF THE PRESENCE OF PASTE IN A CONICAL SPOUTED BED DRYER WITH CONTINUOUS FEEDING

The spouted bed with inert particles has been used as a paste dryer, producing a fine powder. Few authors have studied the behavior of the bed in the presence of paste, which is important for the design of this equipment. In this work the spouting pressure drop, the minimum spouting velocity and the paste residual content in the bed were measured as a function of the feed rate. Experiments were carried out with two Newtonian pastes (egg paste and blood), a pseudoplastic one (xanthan gum suspension) and water, used as a referential material. These three types of paste behaved differently in terms of the variation of the spouting pressure drop and the minimum spouting velocity. The paste residual content in the bed was only measured with the egg paste, and in this case it increased very slightly with the feed rate, until the maximum throughput allowed by the system.     

EFFECT OF THE PRESENCE OF PASTE IN A CONICAL SPOUTED BED DRYER WITH CONTINUOUS FEEDING

ABSTRACT

The spouted bed with inert particles has been used as a paste dryer, producing a fine powder. Few authors have studied the behavior of the bed in the presence of paste, which is important for the design of this equipment. In this work the spouting pressure drop, the minimum spouting velocity and the paste residual content in the bed were measured as a function of the feed rate. Experiments were carried out with two Newtonian pastes (egg paste and blood), a pseudoplastic one (xanthan gum suspension) and water, used as a referential material. These three types of paste behaved differently in terms of the variation of the spouting pressure drop and the minimum spouting velocity. The paste residual content in the bed was only measured with the egg paste, and in this case it increased very slightly with the feed rate, until the maximum throughput allowed by the system.     

DRYING OF SAWDUST IN AN ATMOSPHERIC PRESSURE SPOUTED BED STEAM DRYER

The results presented in this paper show the possibility to control the outgoing moisture content using the exhaust temperature as a control parameter. A model for heat exchange is used to support visual observations of the spouting quality in the bed. The model is also used in a discussion about the heat and mass transfer coefficients. Two efficiency concepts are defined and experimental results presented. The temperature efficiency is used to present the possibility to integrate a steam dryer into energy systems such as boilers and heat sinks. Energy efficiency is used to show the variation of the recoverable heat and to point out suitable outgoing moisture contents for steam dryers. It is important to keep the temperature after the dryer as low as possible in order to achieve a high temperature efficiency. It is also shown that energy efficiency improves with decreasing outgoing moisture content and increasing inlet steam temperature.     

SIMULTANEOUS DRYING AND COMMINUTION OF COAL IN A SPOUTED BED

Coal was dried and simultaneously reduced in size in a spouted bed using air at different temperatures as the spouting fluid and either glass beads as a dynamic grinding aid or a specially designed metal insert as a static grinding aid. Both semi-batch and continuous operations were carried out, the balanced feed and product-discharge rates in the latter being pre-determined from the results in the former. The rates of both drying and comminution were synergistically increased with increases in inlet air temperature. The static insert was shown to be a more effective comminution device than the glass beads.     

PAPER DRYING: A STRATEGY FOR HIGHER MACHINE SPEED. II. IMPINGEMENT AIR DRYING FOR HYBRID DRYER SECTIONS

For printing and heavier grades, combining cylinder and impingement air drying into a multiple technique dryer section can enable higher productivity through higher machine speed. The large differences in local moisture content and temperature across the sheet which develop quickly under high intensity impingement drying provide the potential for reducing drying time by sheet reversal between impingement drying cylinders. This advantage was determined experimentally under low intensity impingement drying conditions. Use of the micro-scale based McGill dryer simulator for determining the advantage from sheet reversal between impingement drying cylinders was demonstrated for both laboratory and industrial impingement drying intensities. For completing the drying of 205 g/m² linerboard from 0.3 to 0.5 kg/kg dry under 400°C air jets of Re 20000, drying time is about 30% less with sheet reversal between two impingement drying cylinders than for a single, larger diameter cylinder. This extensively validated dryer simulator enables determining advantageous design specifications and operating conditions for hybrid dryer sections involving combinations of cylinder and impingement air drying, a concept with potential to become common industrial practice.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

ABSTRACT

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

BIXIN POWDER PRODUCTION IN CONICAL SPOUTED BED UNITS

ABSTRACT

Recent work has demonstrated that the red carotenoid bixin is easily extracted from Bixa orellana seeds by particle attrition and impact rather than by solvent extraction. This technique may require a previous step for drying seeds at a safe temperature to preserve pigment quality. A spouted bed (SB) with a draft tube is the most appropriate equipment to process both seed drying and bixin extraction at low operational costs. Operational parameters of the SB unit are optimized as a function of the powder production rate. The maximum air inlet temperature for drying the seeds is also specified. A high performance liquid chromatography method has been developed for the semi-quantitative determination of bixin content in the powder produced. Results show that this SB unit can be more competitive than ball mill equipment.     

BIXIN POWDER PRODUCTION IN CONICAL SPOUTED BED UNITS

Recent work has demonstrated that the red carotenoid bixin is easily extracted from Bixa orellana seeds by particle attrition and impact rather than by solvent extraction. This technique may require a previous step for drying seeds at a safe temperature to preserve pigment quality. A spouted bed (SB) with a draft tube is the most appropriate equipment to process both seed drying and bixin extraction at low operational costs. Operational parameters of the SB unit are optimized as a function of the powder production rate. The maximum air inlet temperature for drying the seeds is also specified. A high performance liquid chromatography method has been developed for the semi-quantitative determination of bixin content in the powder produced. Results show that this SB unit can be more competitive than ball mill equipment.