Drying Characteristics of Malaysian Paddy: Kinetics & Grain Cracking Quality

Drying kinetics of Malaysian paddy dried in a laboratory scale batch rapid bin dryer was studied. Quality of paddy after drying at temperatures of 60 and 80°C, bed heights of 2 and 4 cm, and at different drying stages was presented in terms of cracking percentage. Moisture content of paddy reduced exponentially with time and became stable at equilibrium moisture content. Characteristic drying rate curves exhibited mainly falling rate period, with an induction period in deep beds, but without the constant rate period. A custom-made light box was built to visually analyze the cracking in paddy kernel. The extent of breakage is directly related to the crack percentage. The percentage of cracks increased with drying and tempering temperatures and was higher after 2 weeks of storage before milling. Bed heights did not significantly affect the head rice yield as much as tempering between two drying stages. Temperatures above 80°C caused severe cracking in paddy kernel and produced miserable yield of head rice after milling, which could be slightly improved by tempering. The use of a proper miller is also important in ensuring good head yield results and whiteness quality.     

Evolution of mechanical properties of parboiled brown rice kernels during impinging stream drying

Information on mechanical properties of parboiled brown rice kernels upon impinging stream drying, which is important for effective control of kernel fissure and head rice yield, is reported. Experiments were performed at the drying temperatures of 130, 150, and 170°C; inlet air velocity of 20?m/s; impinging distance of 5?cm and paddy feed rate of 40?kg_{dry_paddy}/h. Parboiled paddy was dried for up to seven cycles. Between each drying cycle, the paddy was tempered for a period of either 0 (without tempering) or 30?min. The moisture evaporation rate was noted to be very high during the first two drying cycles and rapidly dropped in the later drying cycles. When tempering was included after a particular drying cycle, the drying rate in a subsequent cycle was higher than without tempering. At the kernel moisture contents immediately after drying of 25.3–47.5% (d.b.), the drying temperature and existence of tempering did not affect the mechanical properties although microcracks were formed in the kernels. However, both factors played a more important role on the mechanical properties when the kernels were evaluated at 16% (d.b.). The head rice yield correlated well with the tensile strength of the kernels.     

Rapid Drying of Parboiled Paddy Using Hot Air Impinging Stream Dryer

A method for rapid drying of parboiled paddy via the use of an impinging stream dryer was proposed and assessed. The effects of the drying air temperature, number of drying cycles, as well as time of tempering between each drying cycle on the moisture reduction, head rice yield, and whiteness index of the dried parboiled paddy were studied. The drying experiments were carried out at drying air temperatures of 130, 150, and 170°C; inlet air velocity of 20 m/s; impinging distance of 5 cm; and paddy feed rate of 40 kg_{dry_paddy}/h. Parboiled paddy was dried for up to seven cycles. Between each drying cycle the parboiled paddy was tempered for a period of either 0 (no tempering), 15, 30, 60, or 120 min. After impinging stream drying, paddy was ventilated by ambient air flow until its moisture content reached 16% (db). Moisture reduction of the paddy was noted to depend on both the impinging stream drying temperature and tempering time. Drying at a high temperature along with tempering for a suitable period of time could maintain the head rice yield of the paddy at a level similar to that of the reference parboiled paddy. To avoid discoloration and low head rice yield, parboiled paddy should not be dried at a temperature higher than 150°C and should be tempered for at least 30 min.     

Effects of operating parameters of impinging stream dryer on parboiled rice quality and energy consumption

Abstract

It is very important to know how operating condition of a coaxial impinging stream dryer affects the drying time, parboiled rice quality and energy consumption. The drying temperature, parboiled paddy feed rate, drying air velocity and impinging distance were experimentally investigated. Increases in drying temperature and air velocity and a decrease in paddy feed rate provided higher evaporation rate whilst impinging distance, ranging from 5 to 13?cm, did not affect the evaporation rate. Collision between kernels within the impinging zone caused the hull’s lemma splitting from the kernel and the percentage of the split kernel strongly depended on the air velocity and feed rate. The acceleration in the rate of drying by changing the above operating parameters did not affect the head rice yield. In addition, the collision of kernels also did not influence the head rice yield since the mechanical properties of rice are strengthened during steaming step in the parboiling process. However, the change of head rice quality was only governed by the moisture content after drying. The total energy consumption including electricity and heat was strongly depended on the air velocity and feed rate whilst it was slightly changed with the drying temperature. From the present study, it was recommended that the parboiled paddy should not be dried below 25% d.b. and the highest temperature that could possibly be used was 190?°C and the inlet air velocity should not be below 15?m/s.     

EFFECTS OF DRYING ON HEAD RICE YIELD USING FLUIDIZATION TECHNIQUE

ABSTRACT

Experimental results of fluidized bed paddy drying using high inlet air temperatures (140 and 150 °C) showed that head rice yield could be increased to a maximum value at a range of paddy final moisture contents of 19 to 22 % wet-basis. In case of reducing moisture content of paddy to lower than 19 % wet-basis, head rice yield of tempered paddy was higher than that of no-tempered one. Initial moisture contents of paddy that could increase head rice yield were in a range of 23 to 31 % wet-basis. As initial moisture content increased head rice yield increased. Whiteness of dried paddy was mostly accepted. However, if tempering temperature was higher than 60 °C, it may cause the problems for trade.     

Effect of Fluidized Bed Drying Temperature on Various Quality Attributes of Paddy

Abstract

As reported by many researchers, it was found that fluidized bed paddy drying using high drying air temperatures of over 100°C affected the head rice yield and whiteness of dried rice. However, only a few studies on fluidized bed paddy drying with drying air temperatures below 100°C were so far reported. The main objective of this work was therefore to study the effect of fluidized bed drying air temperature on various quality parameters of Suphanburi 1 and Pathumthani 1 Indica rice. Paddy was dried from the initial moisture contents of 25.0, 28.8, and 32.5% dry basis to 22.5 ± 1.2% dry basis using inlet drying air temperatures between 40 and 150°C at 10°C/step. After fluidized bed drying, paddy was tempered and followed by ambient air aeration until its final moisture content was reduced to 16.3 ± 0.5% dry basis. The results showed that the head rice yield of Suphanburi 1 was significantly related to the inlet drying temperature and initial moisture content whilst there was no significant relationship between the head rice yield, drying temperature and initial moisture content for Pathumthani 1. The whiteness of the two rice varieties was slightly decreased with increase in drying air temperature and initial moisture content. It was also found that the hardness of both cooked rice varieties exhibited insignificant difference (p < 0.05) comparing to rewetted rice, which was gently dried by ambient air aeration in thin layer. The thermal analysis by DSC also showed that partial gelatinization occurred during drying at higher temperatures. Using inlet drying air temperatures in the range of 40–150°C therefore did not affected the quality of cooked rice and paddy. The milling quality of paddy was also well maintained.     

The Diffusion of Moisture in Paddy During Hydration and Dehydration Processes

Hydration and dehydration behavior and the effective diffusivity of paddy during the process of parboiling were studied. Hydration of three different paddy samples (Sherpa low and high head rice yield and Reiziq) were performed below (60°C) and above (90°C) the gelatinization temperature. The hydration period ranged from 5 to 300 minutes at 60°C and 5 to 90 minutes at 90°C. All of the paddy samples showed different hydration behavior below and above the gelatinization temperature, discerned with two different stages at 60°C and three stages at 90°C. Dehydration was carried out at 40°C just after hydration (without tempering the kernel), which mostly took place at the falling rate period. The hydration and dehydration pattern was not different between the high HRY and low HRY paddy, indicating a limited contribution of microfissures to the diffusion rate in the paddy. Five commonly used semi-empirical models were used to predict the hydration and dehydration behavior of paddy and, among them, the Page model was found to be the most suitable. The effective diffusivity during hydration was dependent on the temperature of hydration, which was 1.83 × 10^?11 to 2.11 × 10^?11 m²/s at 60°C and 6.68 × 10^?11 to 7.94 × 10^?11 m²/s at 90°C. The effective diffusivity during dehydration depended on the soaking temperature and period of soaking; it was lower for high-temperature-hydrated samples than low-temperature-hydrated samples. The study concluded that the mass water diffusivity was not affected by the microfissures within the paddy kernel, and the hydration pattern was strongly dependent on whether the temperature was above or below the gelatinization temperature.     

Comparative Study of Effects of Drying Methods and Storage Conditions on Aroma and Quality Attributes of Thai Jasmine Rice

This article describes the effects of various drying treatments and storage conditions on the main quality attributes of Thai jasmine rice; i.e., aroma, milling, pasting, and cooking properties. The experimental results show that drying treatments using various high temperatures (115–150°C) combined with 30 min tempering time between the pass or ambient air drying affect the composition of volatile compounds as well as the commercially accepted quality characteristics of Thai fragrant rice. High-temperature drying followed by ambient air drying can retain most of the quality attributes of Thai jasmine rice than multi-pass high-temperature drying with a tempering period between passes.     

AN APPLICATION OF GLASS TRANSITION TEMPERATURE TO EXPLAIN RICE KERNEL FISSURE OCCURRENCE DURING THE DRYING PROCESS*

Fissure formation during rice drying is a major cause of rice milling quality reduction. This work has applied principles of polymer science in studying thermal and hygroscopic properties of rice kernels, particularly the glass transition temperature (T_g ). This data was used to develop a hypothesis that explains the occurrence of rice kernel fissuring as a result of drying. The drying process was mapped onto a state diagram to illustrate the changes in state that a kernel could incur through drying and tempering operations. An experiment was designed to validate the hypothesis in which the effect of the T_g on rice drying and tempering in terms of milling quality was determined. Results showed that drying air temperatures up to 60°C and high moisture removal rates could be used without reducing the milling quality, as long as sufficient tempering was allowed at a temperature above the T_g of the rice.

     

Stationary versus Fluidized-Bed Drying of High-Moisture Paddy with Rest Period

Drying of high-moisture paddy was examined experimentally under stationary and fluidized bed with and without intervening rest periods. Introduction of a rest period between first and second stage of drying improved drying rate and lowered the energy requirement and increased head rice yield. Fluidization further improved the overall drying process. A single-term drying diffusion equation was suitably fitted to first, rest, and second stage drying data of fluidized and stationary bed by applying nonlinear regression method and effective diffusion coefficients were evaluated. During the period of rest stage, paddy grain released a considerable amount of moisture as an effect of residual grain temperature. An appropriate moisture ratio at which resting should start and the length of resting were evaluated by measuring changes in relative humidity in the headspace of mass of paddy and also from the diffusion coefficient values obtained from the experimental drying data. Resting duration between 75 and 90 min at moisture ratio around 0.715 was found suitable for overall good performance in both fluidized and stationary bed drying. A considerable amount of energy (21–44%) can be saved by providing a rest period from 30 to 120 min between the two stages of drying. Fluidization further reduces (≈ 50% against continuous drying under stationary bed) the energy requirement. No significant difference was found in head rice yield obtained from fluidized and stationary bed experiments, though discontinuing drying by providing intervening rest periods considerably improved the percentage head rice when compared with the results from continuous drying.     

流态化及缓苏干燥技术对泰国香稻的香味和磨粉品质的影响

将高温（〉100。C）流态化干燥和缓苏相结合干燥泰国香稻（KhaoDawkMali105，籼稻），使其湿含量降至13-14％（湿基），以便于安全贮存。研究了干燥与贮存过程对籼米香味和磨粉品质的影响。泰国香稻需要经过两个干燥阶段。第一阶段是在高温流化床中干燥，缓苏30分钟，然后返回高温流化床干燥或阴干，直至湿含量降低到安全贮存水平。实验结果表明，干燥温度对香稻的整精米率（HRY）、白度指数（wI）和2AP含量均有影响。多数干燥温度下整精米率的水平都比较低，但150℃除外，此情况下整精米率（psO．05）显著提高。然而，当一次流态化干燥和缓苏之后，以阴干代替二次流态化干燥，香稻的整精米率显著增加，尤其是在135℃和50℃时（p≤O．05）。在贮存期间，白度指数和2AP舍量显著降低（ps0．05），而整精米率保持不变。对比环境温度（28．30℃）和15℃贮存温度，结果表明保持香米2AP舍量和白度指数的适宜保存温度是15℃。然而贮存条件对整精米率影响不大（p〉0．05）。本研究将有益于泰国香米行业的发展，为泰国香米的干燥起到指导性作用。     

A Combined Experimental and Theoretical Approach to Study Temperature and Moisture Dynamic Characteristics of Intermittent Paddy Rice Drying

Intermittent drying of paddy rice is fully investigated both theoretically and experimentally. A model is developed to describe simultaneous heat and mass transfer for the drying stages and mass transfer for the tempering ones. The model is considered for both cylindrical and spherical geometries. The model excels in considering non-constant paddy rice and air physical properties as well as surface vaporization and convection. The consequent equations are numerically solved with finite-difference method of line using implicit Runge–Kutta. Furthermore, a set of experiments is conducted in a laboratory-scale fluidized bed dryer to estimate the moisture diffusivity of rice and evaluate the effects of different parameters. Two correlations for moisture diffusivity are derived for each geometry based on the experimental results. It is noteworthy that the geometry choice leads to significantly different moisture diffusivities. As a result, the diffusivity values obtained for spherical presentation is 2.64 times greater than that of cylinder. Moreover, the cylindrical model fits the experimental results more precisely, especially for tempering stage (AARD_cyl = 1.03%; AARD_sph = 1.53%). Model results reveal that thermal equilibrium is quickly reached within the first 2 min. Air velocity shows no influential effect on drying upon establishment of fluidized condition. In addition, drying rate is drastically improved after applying the tempering stage. A definition for tempering stage efficiency is also proposed which shows that 3 h tempering will be 80% efficient for the studied case. Rising temperature significantly improves the drying rate, while it does not contribute much in the tempering efficiency.     

Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

Abstract

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6–30.8°C, average relative humidity of 65.2–80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.     

EFFECT OF TEMPERING ON SUBSEQUENT DRYING OF PADDY USING FLUIDISATION TECHNIQUE

Drying and tempering models for paddy drying by a fluidised bed technique have been developed to describe the moisture movement inside a single paddy kernel. The grain shape was considered as a finite cylinder. The internal diffusion is an important contribution to control the drying rate of paddy. The dependence of effective diffusion coefficient on drying temperature can be adequately explained based on Arrhenius form. The parameters of this equation were evaluated in the range of temperatures between 110°C and 170°C by using the regression analysis with 189 experimental drying data. As compared with no tempering, the faster drying rate can be obtained by tempering treatment between drying stages. The effect of degrees of tempering on determining the moisture reduction in the second stage has also been explored. According to the simulation results, a prediction equation of the required tempering time for the tempering index of 0.95 has been established in which the drying air temperature, initial moisture content and drying time are taken into account. The tempering time for 35 min is recommended for the continuous fluidised bed dryers being operated in rice mills.     

MANAGING MOIST PADDY BY DRYING,TEMPERING AND AMBIENT AIR VENTILATION

ABSTRACT

This paper describes a strategy for reducing moisture in paddy by fluidized bed drying, tempering and ambient air cooling. Experimental results showed that after the three processes, moisture content was reduced from 33 % to 16.5 % dry-basis within approximately 53 minutes. During the first process, a fluidized-bed dryer was used to reduce the moisture content of paddy down to 19.5 % dry-basis within 3 minutes. Then the paddy was tempered for 30 minutes. Finally, it was cooled by ambient air (temperature and relative humidity of 30 °C and 55-60% respectively) with air velocity of 0.15 m/s for 20 minutes. Quality of paddy in terms of head rice yield and whiteness was acceptable.     

Effect of tempering approach following cross-flow drying on rice milling yields

Abstract

Three tempering approaches were followed after drying rough rice at 16.3% and 20.5% initial moisture contents (IMCs) using 57?°C/13% RH air at an airflow of 0.56 (m³/s)/m² for 30, 60, and 90?min in an experimentally simulated cross-flow drying column. For the longer drying durations, post-tempering head rice yields were consistently less when the interstitial air from rice from different cross sections of the drying column was allowed to “interact” during tempering than when the rice from these different cross sections was tempered separately; this effect was more prominent at the greater rice IMC. RH of the interstitial air during tempering was measured and used to estimate the minimum tempering durations required for the different tempering approaches.     

Stationary versus Fluidized-Bed Drying of High-Moisture Paddy with Rest Period

Drying of high-moisture paddy was examined experimentally under stationary and fluidized bed with and without intervening rest periods. Introduction of a rest period between first and second stage of drying improved drying rate and lowered the energy requirement and increased head rice yield. Fluidization further improved the overall drying process. A single-term drying diffusion equation was suitably fitted to first, rest, and second stage drying data of fluidized and stationary bed by applying nonlinear regression method and effective diffusion coefficients were evaluated. During the period of rest stage, paddy grain released a considerable amount of moisture as an effect of residual grain temperature. An appropriate moisture ratio at which resting should start and the length of resting were evaluated by measuring changes in relative humidity in the headspace of mass of paddy and also from the diffusion coefficient values obtained from the experimental drying data. Resting duration between 75 and 90 min at moisture ratio around 0.715 was found suitable for overall good performance in both fluidized and stationary bed drying. A considerable amount of energy (21-44%) can be saved by providing a rest period from 30 to 120 min between the two stages of drying. Fluidization further reduces (≈ 50% against continuous drying under stationary bed) the energy requirement. No significant difference was found in head rice yield obtained from fluidized and stationary bed experiments, though discontinuing drying by providing intervening rest periods considerably improved the percentage head rice when compared with the results from continuous drying.     

Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3–4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20–30% lower than the non-cyclone-equipped dryer.     

AN APPLICATION OF GLASS TRANSITION TEMPERATURE TO EXPLAIN RICE KERNEL FISSURE OCCURRENCE DURING THE DRYING PROCESS *

Fissure formation during rice drying is a major cause of rice milling quality reduction. This work has applied principles of polymer science in studying thermal and hygroscopic properties of rice kernels, particularly the glass transition temperature (T_g). This data was used to develop a hypothesis that explains the occurrence of rice kernel fissuring as a result of drying. The drying process was mapped onto a state diagram to illustrate the changes in state that a kernel could incur through drying and tempering operations. An experiment was designed to validate the hypothesis in which the effect of the T_g on rice drying and tempering in terms of milling quality was determined. Results showed that drying air temperatures up to 60°C and high moisture removal rates could be used without reducing the milling quality, as long as sufficient tempering was allowed at a temperature above the T_g of the rice.     

Effects of High-Temperature Fluidized Bed Drying and Tempering on Kernel Cracking and Milling Quality of Vietnamese Rice Varieties

Studies on the effects of high-temperature fluidized bed drying and tempering on physical properties and milling quality of two long-grain freshly harvested Vietnamese rice varieties, A10 (32±1% wet basis moisture) and OM2717 (24.5±0.5% wet basis moisture), were undertaken. Rice samples were fluidized bed dried at 80 and 90°C for 2.5 and 3.0 min, then tempered at 75 and 86°C for up to 1 h, followed by final drying to below 14% moisture (wet basis) at 35°C by thin-layer drying method. Head rice yield significantly improved with extended tempering time to 40 min. Head rice yield tended to increase with decreasing cracked (fissured) kernels. The hardness and stiffness of sound fluidized bed dried rice kernels (in the range of 30–55 N and 162–168 N/mm, respectively) were higher than that of conventionally dried ones (thin layer dried at 35°C). The color of milled rice was significantly (P < 0.05) affected by high-temperature fluidized bed drying, but the absolute change in the value was very small.