Design and Performance Evaluation of a Solar-Assisted Biomass Drying System with Thermal Storage

A solar biomass hybrid air heating system that does not require a conventional auxiliary heater but can still provide a daily load fraction exceeding 90% and supply hot air at a steady temperature and flow rate continuously for 24 h a day has been developed. The system, which combines an unglazed transpired solar collector, rock bed, and a biomass gasifier stove with heat exchanger, was evaluated by drying chilli using air at 60°C and 90 m³/h. The chilli was dried from 76.7% moisture (w.b.) to 8.4% over 32.5 h of continuous drying. The dryer reduced the drying time by 66% compared to open sun drying and provided 91.6% load fraction during the 24-h operation. The temperature of hot air supplied was stable at 60±3°C for about 21 h during the entire drying duration.     

THIN LAYER SOLAR DRYING OF SOME VEGETABLES

In this study, a solar cabinet dryer consisting of a solar air heater and a drying cabinet, was used in drying experiments. Pumpkin, green pepper, stuffed pepper, green bean, and onion were dried in thin layers. Three different drying air velocities were applied to the process of drying to determine their effects on drying time. Fresh materials were dried by a natural sun drying method. In order to explain drying curves of these products different moisture ratio models were performed and evaluated based on their determination coefficients (R²). Our results revealed that drying air temperature could increase up to about 46°C. Drying air velocity had an important effect on drying process. Drying time changed between 30.29 and 90.43 hours for different vegetables by the solar drying. This drying time was between 48.59 and 121.81 hours for the natural sun drying. Drying curves could be explained by determined thin layer drying models satisfactorily with very high determination coeffcients.     

THIN LAYER SOLAR DRYING OF SOME VEGETABLES

In this study, a solar cabinet dryer consisting of a solar air heater and a drying cabinet, was used in drying experiments. Pumpkin, green pepper, stuffed pepper, green bean, and onion were dried in thin layers. Three different drying air velocities were applied to the process of drying to determine their effects on drying time. Fresh materials were dried by a natural sun drying method. In order to explain drying curves of these products different moisture ratio models were performed and evaluated based on their determination coefficients (R²). Our results revealed that drying air temperature could increase up to about 46°C. Drying air velocity had an important effect on drying process. Drying time changed between 30.29 and 90.43 hours for different vegetables by the solar drying. This drying time was between 48.59 and 121.81 hours for the natural sun drying. Drying curves could be explained by determined thin layer drying models satisfactorily with very high determination coeffcients.     

DRYING OF MEDICINAL PLANTS WITH SOLAR ENERGY UTILISATION

ABSTRACT

In the paper, a potential of solar energy for drying of medicinal plants in Polish conditions is estimated and development of solar drying technologies is presented. The results of economic assessment of flat-plate solar collectors applied for drying of medicinal plants on a farm are promising. In some specific conditions, e.g. drying of wild grown medicinal plants in remote areas, even application of photovoltaic modules for driving of a fan of a solar dryer is a profitable option and enables easy control of the drying air temperature.     

Usage of solar-assisted spouted bed drier in drying of pea

The main objective of this study is to evaluate the effects of solar-assisted spouted bed and open sun drying on the drying rate and quality parameters of pea. Color, shrinkage, bulk and apparent densities, internal and bulk porosities, rehydration capacity and microstructure were the quality parameters investigated in dried product.Drying rate for solar-assisted spouted bed was about 3.5 times of drying rate for open sun drying. Air temperature changed between 20 °C and 27.4 °C during open sun drying while temperature of air at the inlet of solar-assisted spouted bed dryer varied between 35.3 °C and 65.5 °C during the experiments. Effective diffusivities were found to be 0.64 × 10^?10 and 3.27 × 10^?10 m²/s for open sun and solar-assisted spouted bed drying of pea, respectively. In color analysis, it was observed that a* value increased while b* value decreased for both drying methods. Bulk density and apparent density of peas dried under open sun was higher than that in solar-assisted spouted bed drier. In both drying methods, internal and bulk porosities decreased. Shrinkage was more for open sun dried samples. Rehydration capacity for solar-assisted spouted bed dried sample was higher than the one for open sun dried.     

SOLAR ASSISTED DRIER FOR SEEDS

A high performance solar assisted seed dryer has been designed and constructed at a seed processing station in Hungary.

The dryer is arranged in a building specially designed for this purpose, the roof of it serves as solar air collector field. Two drying cells with individual fans of two RPM stages are formed in the building. Drying air preheated by the collector can optionally be distributed between the two drying cells. Material to be dried can be arranged either in a static bed or in containers depending on the requirements. Moist air leaving the bed streams out of the drying cells through openings of the side walls. As auxiliary air heater a natural gas generator is used.     

FUNDAMENTALS OF LIQUID SPRAY TECHNIQUES

Two twin forced convection dryers of 1.5 m³ were built in Majorca (Spain). They are of a mixed kind, with solar air collectors and a green house type chamber. A wooden frame supports polycarbonate walls. After two years operation they have been proven weather resistant. Six solar air collectors 2.12 × 1.05 m were used in each dryer.

Apricots were processed in both dryers and at open sun. Three different tray heights were tested 5, 9 and 12 cm. The best results were obtained with 12 cm trays. Recycling part of the exhaust air improves the efficiency of the dryer. Blanching the fruits makes no difference to the dehydration rate. The rate of SO₂ loss during the drying process is higher within the chamber.     

Solar Drying of Peeled Longan Using a Side Loading Type Solar Tunnel Dryer: Experimental and Simulated Performance

This article presents experimental and simulated results of drying of peeled longan in a side-loading solar tunnel dryer. This new type of solar tunnel dryer consists of a flat-plate solar air heater and a drying unit with a provision for loading and unloading from windows at one side of the dryer. These are connected in series and covered with glass plates. A DC fan driven by a 15-W solar cell module supplies hot air in the drying system. To investigate the experimental performance, five full-scale experimental runs were conducted and 100 kg of peeled longan was dried in each experimental run. The drying air temperature varied from 32 to 76°C. The drying time in the solar tunnel dryer was 16 h to dry peeled longan from an initial moisture content of 84% (w.b.) to a final moisture content of 12% (w.b.), whereas it required 16 h of natural sun drying under similar conditions to reach a moisture content of 40% (w.b.). The quality of solar-dried product was also good in comparison to the high-quality product in markets in terms of color, taste, and flavor. A system of partial differential equations describing heat and moisture transfer during drying of peeled longan in this solar tunnel dryer was developed and this system of nonlinear partial differential equations was solved numerically by the finite difference method. The numerical solution was programmed in Compaq Visual FORTRAN version 6.5. The simulated results agreed well with the experimental data for solar drying. This model can be used to provide the design data and it is essential for optimal design of the dryer.     

Drying Kinetics and Color Retention of Dehydrated Rosehips

Abstract

Freshly harvested rosehips (Rosa canina L.) were dehydrated in a parallel flow type air dryer at six air temperatures (30, 40, 50, 60, and 70°C) at air velocities of 0.5, 1.0, and 1.5 m/s. Drying air temperature and velocity significantly influenced drying time and energy requirement. Minimum and maximum energy requirement for drying of rosehips were determined as 6.69 kWh/kg for 70°C at 0.5 m/s, and 42.46 kWh/kg for 50°C, 1.5 m/s. In order to reduce drying energy consumption, it is recommended that the drying air velocity must not be more than 0.5 m/s and drying air temperature should be 70°C. In addition, the influence of drying air temperature and air velocity on the color of dried rosehip has been studied. Hunter L, a, b values were used to evaluate changes in the total color difference (ΔE) on dried rosehips. 70°C drying air temperature and 1 m/s air velocity were found to yield better quality product.     

Evaluating a Solar Dryer for In-Shell Drying of Split Pistachio Nuts

Abstract

A thin-layer forced air solar dryer was designed to study the feasibility of drying pistachio nuts. The dryer was tested during the 2001 and 2002 drying seasons. The maximum temperature in the solar collector reached 56°C, which was 20°C above the ambient temperature. The required drying time was 36 h. During the first day of drying (0800 to 1700 h) the moisture content dropped to about 21% (wb). The final moisture content of the dried nuts was 6% wb, which was 1% below the recommended storage moisture. The drying constant of the pistachio nuts during solar drying was determined using two mathematical models, a one-term series solution of Fick's diffusion equation and an exponential decaying model. There was no significant difference between the two models (α = 0.05). In general, the quality of solar dried nuts was better than the conventional heated air due to slower drying rates.     

A Method for Determination of Porosity Change from Shrinkage Curves of Deformable Materials

The novel low-cost band thermodynamic dryer equipped with a solar collector, a parabolic focusing collector, a heat exchanger, screw fan, and a drying cabinet with a band was designed and tested. The maximum temperature in the solar collector reached 85°C, which was 55°C above the ambient temperature. The required drying time was 4.5 h, much reduced from the traditional solar drying time of 48 h. The final moisture content of the Roselle calyx was 12% w.b., which is the recommended storage moisture content. Measurements of ambient temperature and humidity, air temperature, and relative humidity inside the dryer as well as solids moisture loss-in-weight data are employed as a means to study the performance of the dryer. Solar drying was compared with conventional sun drying and heated air drying, using the following evaluation criteria: drying time, dried Roselle color, texture, taste, and production cost. For evaluation, a model-based Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) methodology was used. After the evaluation, the proposed continuous solar dryer was found to be better than conventional drying and heated air drying due to slower drying rate and better quality of the dried Roselle.     

Mathematical Modeling of Drying Characteristics of Indian Mackerel (Rastrilliger kangurta) in Solar-Biomass Hybrid Cabinet Dryer

Eight trials were conducted for drying mackerel by a solar biomass hybrid cabinet dryer (S-BHCD) and open sun drying (OSD) at air temperatures of 32.39–57.69°C, relative humidity 23.9–85.8%, and air flow rate of 0.20–0.60 m/s. The solar radiation ranged between 287 and 898 W/m² during the time of experimentation. At nighttime, drying was carried out by combusting biomass. The initial moisture content of the processed mackerel was 72.50±0.44% (w.b.) and was reduced to the final moisture content of 16.67±0.52% (w.b.) in S-BHCD and 16.92±0.54% (w.b.) in OSD. Eleven drying models were used and the coefficients of determination (R ²) and constants were evaluated by nonlinear regression to estimate the drying curves of dried mackerels. The Midilli model was found to more satisfactorily describe the drying process of mackerel in S-BHCD with R ² of 0.9999, χ² of 0.0000374, and RMSE of 0.0057. In the OSD, a two-term drying model satisfactorily described the drying process with R ² of 0.9996, χ² of 0.0000519, and RMSE of 0.0072. The variation of Free Fatty acid (FFA), Peroxide value (PV), Thiobarbituric acid (TBA), Total volatile bases nitrogen (TVB-N), Trimethylamine nitrogen (TMA-N), and histamine contents of dried mackerel by using S-BHCD showed very high corresponding coefficients of determination, where all R ² were greater than 0.90, except TBA value. Bacterial count and mold growth were decreased significantly (P < 0.05). There was no discoloration of the product during 4 months of storage. Contour plots of S-BHCD and OSD dried mackerel also showed that for all sensory attributes examined, panelists preferred fish dried with S-BHCD. The organoleptic analysis showed that the S-BHCD drying methods have a highly significant effect (P < 0.01) on texture and overall acceptability. Biochemical, microbial analysis, and sensory evaluation showed that the product was in prime acceptable form for 4 months of storage at ambient temperature.     

Development and Performance Analysis of a New Solar Energy-Assisted Photocatalytic Dryer

A novel patented solar energy-assisted photocatalytic closed-type dryer (SEPCD) was developed to produce dried agro-foods without using chemical additives for antisepsis and/or color retention and to retain higher nutritive value of the fresh produce. The SEPCD was designed to simulate open sun drying with moving dry air and mild temperature. The air temperature in the drying cabinet is maintained at 40-45°C; it is supplied partially by a dehumidification system and partially by a solar energy system. Additionally, the inside of the cabinet was coated with titanium dioxide (TiO₂) to cause a bactericidal effect during the drying process. Results showed that the total mold and bacterial counts for the drying cabinet and dried pineapple slices are significantly reduced in the SEPCD while the dried food quality is also better than that dried by conventional hot air drying.     

The drying kinetics of seeded grape in solar dryer with PCM-based solar integrated collector

This paper presents a novel type of dryer for experimentally evaluating the drying kinetics of seeded grapes. In the developed drying system, it has been particularly included an expanded-surface solar air collector, a solar air collector with phase-change material (PCM) and drying room with swirl element. An expanded-surface solar air collector has been used to achieve high heat transfer and turbulence effect whiles a solar air collector with PCM has been used to perform the drying process even after the sunset. On the other hand, the swirl elements have been located to give the swirl effect to air flow in drying room. These advantages make the proposed novel system a promising dryer in that lower moisture value and less drying time. The drying experiments have been carried out simultaneously both under natural conditions and by the dryer with swirl flow and without swirl flow at three different air velocities. The obtained moisture ratio values have been applied to six different moisture ratio models in the literature. The model having the highest correlation coefficient (R) and the lowest Chi-square (χ²) value has been determined as the most relevant one for each seeded grape drying status.     

SOLAR ASSISTED DRIER FOR SEEDS

A high performance solar assisted seed dryer has been designed and constructed at a seed processing station in Hungary.

The dryer is arranged in a building specially designed for this purpose, the roof of it serves as solar air collector field. Two drying cells with individual fans of two RPM stages are formed in the building. Drying air preheated by the collector can optionally be distributed between the two drying cells. Material to be dried can be arranged either in a static bed or in containers depending on the requirements. Moist air leaving the bed streams out of the drying cells through openings of the side walls. As auxiliary air heater a natural gas generator is used.     

Drying Kinetics of Tomato Slices in Vacuum Assisted Solar and Open Sun Drying Methods

A lab model vacuum-assisted solar dryer was developed to study the drying kinetics of tomato slices (4, 6, and 8 mm thicknesses) compared with open sun drying under the weather conditions of Montreal, Canada. The drying study showed that the time taken for drying of tomato slices of 4, 6, and 8 mm thicknesses from the initial moisture content of 94.0% to the final moisture content of around 11.5 ± 0.5% (w.b.) was 360, 480, and 600 min in vacuum-assisted solar dryer and 450, 600, and 750 min in open sun drying, respectively. During drying, it was observed that the temperature inside the vacuum chamber was increased to 48°C when the maximum ambient temperature was only 30°C. The quality of tomato slices dried under vacuum-assisted solar dryer was of superior quality in terms of color retention and rehydration ratio. The drying kinetics using thin-layer drying models and the influence of weather parameters such as ambient air temperature, relative humidity, solar insolation, and wind velocity on drying of tomato slices were evaluated.     

Drying behavior of prina (crude olive cake) using different types of dryers

The purpose of this research is to investigate the drying kinetics and determine the suitable drying method of prina, which is obtained after pressing of olives in olive oil factories, and which cannot be used efficiently in certain sectors. Drying experiments were performed at drying temperatures of 60°C, 70°C, and 80°C at a fixed air velocity of 2 m/s using a hot air dryer and with microwave powers of 90 W, 360 W, and 600 W using a microwave dryer. The prina layer thicknesses were selected as 7, 9, and 11 mm for both drying methods. The minimum energy consumption values were measured as 42.0 Wh for 600 W power level and 7 mm layer thickness, and 10260 Wh for 7 mm layer thickness and 80°C temperatures. It was found that energy consumption during hot air drying was more than that of microwave drying. As a result, the suitable dryer and thickness of layer were selected as microwave dryer and 7 mm, respectively. The results of statistical analyses showed that the most suitable model to define the drying behavior of prina samples were found to be the Page model for the microwave dryer and Wang &; Singh model for the hot air dryer. Also, penetration depth, the loss tangent value (tanδ), dielectric constant of material (?^?), and dielectric loss factor (?^??) of dried prina were calculated as 34.51 cm, 0.1059, 75.65, and 8.01, at 2450 MHz, respectively.     

An Experimental Study on Drying of Green Apples

Drying behavior of green apples in a laboratory dryer was examined. Prior to drying, the apples were cut in 8 mm thick slices, which were then treated with citric acid solution and blanched hot water at 80°C. Next, they were dried at 65°C with an air velocity of 2.0 m/s. The shortest drying time (270 min) was obtained with apples pretreated with citric acid solution. The drying data were fitted with 11 mathematical models available in the literature. Selection of the best model was investigated by comparing the determination of coefficient (R ²), reduced chi-square (χ²), root means square error ( RMSE ), and mean relative percentage error (P) between the experimental and predicted values. The results showed that the Wang and Singh, logarithmic, and Verma et al. models gave the best results in describing thin-layer drying of apple slices. The effective moisture diffusivity of pretreated samples with citric acid solution was higher than the other samples.     

Drying of Sodium Acetate in a Pulsed Fluid Bed Dryer

Sodium acetate crystals obtained from the reaction of acetic acid with sodium hydroxide are usually dried in rotary or fluidized beds. In this study, a batch pulsed fluid bed dryer with a 0.18 m² cross‐sectional area was used in an attempt to reduce energy consumption and increase productivity. Drying curves of sodium acetate were determined for different conditions: inlet air temperature of 65 and 80 °C and pulsation frequency of 0 rpm (conventional fluidized bed), 500 and 900 rpm (pulsed fluid bed). A 2² factorial design was used to analyze the results. The intermittent flow helped to break agglomerates and provided better contact between particles and the gas. Drying rates were higher under pulsed fluidization when compared to conventional fluidization. Conventional fluidized bed drying consumed 2.5 times more energy at 80 °C. The influence of temperature on the drying rate was also evident.