Measurement of constant drying rate of wet material placed in a fluidized bed of inert particles under reduced pressure

The objective of this study is to estimate the drying characteristics of a relatively large material immersed in a fluidized bed under reduced pressure by measuring the constant drying rate. The constant drying-rate period in a fluidized bed under reduced pressure is difficult to measure because it is extremely short. To maintain the constant drying-rate period, distilled water is directly supplied to the drying material. Through our experiment, the heat transfer coefficient of the material surface was also determined. The results were compared with data on hot air drying. The constant drying rate is higher for fluidized bed drying than for hot air drying. It suggests that the heat transfer coefficient on the surface of the drying material is much larger for fluidized bed drying than for hot air drying. For fluidized bed drying, the effect of pressure in the drying chamber on the heat transfer coefficient is slight at the same normalized mass velocity of dry air (G/G_mf). The temperature difference between the inside of the drying chamber and the drying material is much smaller for fluidized bed drying than for hot air drying. The constant drying rate increases as the pressure in the drying chamber decreases.     

Evaporation of Distilled Water in a Fluidized Bed of Various Types of Fluidizing Particles Under Reduced Pressure

An objective of this study is to continuously obtain dispersed, dry, fine powders from a dilute suspension of heat-sensitive materials at a low temperature and high drying rate. A fluidized bed under reduced pressure was used in this study and, as a first step, only distilled water (without solid powders) was used as a sample. Drying characteristics were examined for various types of fluidizing particles. The diameter of fluidizing particle varied for inert particles (glass beads). Three kinds of hygroscopic porous particles (silica gel beads; 3A, 4B, and 5D) were also used as fluidizing particles. Under reduced pressures, the maximum drying rate was found to be higher than that at atmospheric pressure, while the bed temperature became lower with an increase in the maximum drying rate (i.e., drying at lower temperature with a higher drying rate is possible under reduced pressures. As diameter of the fluidizing particle was increased, the maximum drying rate became higher, although the amount of gas required for fluidization also increased. The maximum drying rates for silica gel beads were found to be almost equal to those of glass beads, with the exception of 3A silica gel beads (having a smaller pore diameter). The bed temperature was lower for silica gel beads compared to glass beads at the same maximum drying rate (i.e., silica gel beads (hygroscopic porous particles) are superior to glass beads (inert particles) with regard to drying at low temperatures at a high drying rate).     

湿污泥颗粒的流化床干燥实验及模型

在鼓泡流化床内以河砂为干燥介质,对单颗粒湿污泥的流态化干燥特性进行实验研究,得到了流化床温度、污泥初始水分、污泥粒径及流化速度对干燥速率的影响规律：流化床温度及污泥粒径对干燥速率的影响都呈指数规律;污泥的水分越大,干燥速率越大;在鼓泡流化床流化速度达到2倍临界流化速度以上时,充分流化,流化速度再增大(2~5倍临界流化速度)对干燥速率没有明显影响. 在基本的扩散传质理论的基础上,利用实验数据回归得到湿污泥在鼓泡流化床内干燥的半经验模型,为流化床污泥干燥器的设计提供了基础数据和依据.     

旋流振动流化床干燥性能的研究

文章以聚四氟乙烯粒子和蔗糖为物料研究了旋流振动流化床的流体力学及干燥特性,并与振动流化床的各种特性进行了对比。实验在一个干燥室直径为240 mm的小型圆筒振动流化床中进行,采用斜孔分布板使床内产生旋流。实验结果表明:在空气分布板开孔率相差不多的情况下,物料流化以前,旋流振动流化床的床层压降要大于普通振动流化床,一旦物料达到正常流化状态以后,2种振动流化床的床层压降相差不多;旋流振动流化床可以降低物料的临界含湿质量分数。     

Optimization fluidization characteristics conditions of nickel oxide for hydrogen reduction by fluidized bed reactor

We evaluated the optimal conditions for fluidization of nickel oxide (NiO) and its reduction into high-purity Ni during hydrogen reduction in a laboratory-scale fluidized bed reactor. A comparative study was performed through structural shape analysis using scanning electron microscopy (SEM); variance in pressure drop, minimum fluidization velocity, terminal velocity, reduction rate, and mass loss were assessed at temperatures ranging from 400 to 600 °C and at 20, 40, and 60 min in reaction time. We estimated the sample weight with most active fluidization to be 200 g based on the bed diameter of the fluidized bed reactor and height of the stocked material. The optimal conditions for NiO hydrogen reduction were found to be height of sample H to the internal fluidized bed reactor diameter D was H/D=1, reaction temperature of 550 °C, reaction time of 60 min, superficial gas velocity of 0.011 m/s, and pressure drop of 77 Pa during fluidization. We determined the best operating conditions for the NiO hydrogen reduction process based on these findings.     

Investigation of Drying Geldart D and B Particles in Different Fluidization Regimes

Drying of nylon (Geldart D) and expanded polystyrene (Geldart B) particles in fixed and fluidized beds were studied experimentally and theoretically. Fluidized bed dryers are sometimes operated at velocities beyond bubbling fluidization to mitigate against de‐fluidization of surface wet particles. It was found that theoretical analysis using three different drying methods could predict the constant‐drying rate at such velocities and also across the entire fluidization regimes (fixed bed, bubbling, slugging and turbulent fluidization) as long as the bed remains completely fluidized. Results also showed that the theoretical predictions were accurate beyond previously reported velocity limits in a laboratory scale dryer. During bubbling fluidization, the cross flow factor method was used effectively to predict the influence of bubble phase on drying rates. In the falling‐rate period, it is demonstrated that the drying behaviour of nylon at different gas velocities can be characterised by a single normalized drying curve.     

酒精污泥在内热式振动流化床中的干燥特性研究

以干污泥颗粒为惰性粒子,采用内热式振动流化床对酒精污泥进行了干燥实验,考察了流化气速、进气温度、振动频率和内加热功率对污泥干燥特性的影响,分析了污泥湿含量和干燥速率的变化规律。结果表明,干燥速率随着流化气速、进气温度和内加热功率的增加而增加,随着振动频率增加呈先增长后降低的趋势。适度提高流化气速、进气温度、振动频率和内加热功率可以降低最终湿含量。将干燥过程分为降速I段和降速Ⅱ段,根据扩散传质理论,建立了内热式振动流化床中污泥干燥的数学模型,模型计算值和实测值的误差在20%以内,符合较好。实验结果为酒精污泥干燥过程的工业设计和操作提供了实验依据。     

BATCH VIBRATING FLUID BED DRYER FOR SAWDUST PARTICLES: EXPERIMENTAL RESULTS

ABSTRACT

In a batch experimental equipment, the behavior of a sawdust dryer in a vibrating fluidized bed is analyzed. Empirical data concerning fluidization velocities, pressure drops and drying kinetics was obtained, and advantages of using vibration in the drying chamber, relative to a conventional fluidized bed, are shown. This technique is presented as an alternative to solve problems of solid agglomeration and bed defluidization. Results show that it is possible to dry sawdust with more than 2 kg/kg moisture, in a vibrating bed keeping a high degree of bed homogeneity and high quality of fluidized state.     

Drying of Pepper Seed Particles in a Superheated Steam Fluidized Bed Operating at Reduced Pressure

A series of drying experiments was performed in a reduced-pressure superheated steam fluidized bed, employing pepper seed particles and some novel data were obtained. Experiments were carried out using different chamber pressures (40–67 kPa), temperatures (90–122°C), steam velocities (2.35–4.10 m/s), and mass flow rates (0.0049–0.0134 kg/s). In the majority of the experiments, the moisture gain observed in some other studies in the warm-up period of the process was prevented through some supplementary heat provided to the column. The drying rate was found to be increasing by operating temperature; however, it was not affected much by the superficial gas velocity and the operating pressure. Nevertheless, the reduced pressure operation increases the degree of superheating that appears as the most important parameter of the process. The experimental results showed that the equilibrium moisture content decreases by the increasing degree of superheating. On the other hand, the critical moisture content assumes higher values for the greater degrees of superheating. It was concluded that a relatively lower temperature process can be achieved through a reduced-pressure superheated steam fluidized bed.     

Experimental investigation of a rotating fluidized bed in a static geometry

Rotating fluidized beds in a static geometry are based on the new concept of injecting the fluidization gas tangentially in the fluidization chamber, via multiple gas inlet slots in its cylindrical outer wall. The tangential injection of the fluidization gas fluidizes the particles tangentially and induces a rotating motion, generating a centrifugal field. Radial fluidization of the particle bed is created by introducing a radially inwards motion of the fluidization gas, towards a centrally positioned chimney. Correctly balancing the centrifugal force and the radial gas-solid drag force requires an optimization of the fluidization chamber design for each given type of particles. Solids feeding and removal can be continuous, via one of the end plates of the fluidization chamber.The fluidization behavior of both large diameter, low density polymer particles and small diameter, higher density salt particles is investigated at different solids loadings in a 24 cm diameter, 13.5 cm long non-optimized fluidization chamber. Scale-up to a 36 cm diameter fluidization chamber is illustrated.Provided that the solids loading is sufficiently high, a stable rotating fluidized bed in a static geometry is obtained. This requires to minimize the solids losses via the chimney. With the polymer particles, a dense and uniform bed is observed, whereas with the salt particles a less dense and less uniform bubbling bed is observed. Solids losses via the chimney are much more pronounced with the salt than with the polymer particles.Slugging and channeling occur at too low solids loadings. The hydrostatic gas phase pressure profiles along the outer cylindrical wall of the fluidization chamber are a good indicator of the particle bed uniformity and of channeling and slugging. The fluidization gas flow rate has only a minor effect on the occurrence of channeling and slugging, the solids loading in the fluidization chamber being the determining factor for obtaining a stable and uniform rotating fluidized bed in a static geometry.     

流化床氛围下多孔物料干燥传热传质的数值模拟

用有限差分法数值求解一个热、质传递耦合模型,理论研究多孔物料流化床干燥过程。方程离散采用全隐格式的控制容积方法,三对角矩阵法（TDMA）用来求解线性方程组。选用球形的苹果丁作为多孔物料。在典型操作条件下,通过分析温度、饱和度和压力的分布侧形,讨论了物料内部的热、质传递机理。在对比条件下,考察了气体入口温度、气速和床面积因子对干燥过程的影响。结果表明：干燥过程受气、固相间的耦合传热传质的影响十分明显,干燥时间随气体入口温度和气速的提高而减少;随床面积因子的增大而增加。     

Effect of Humidity on Drying of Porous Materials in Fluidized Bed under Reduced Pressure

For fluidized bed drying under a reduced pressure, the effect of the humidity of the drying gas on the drying characteristics of porous materials immersed in the bed was examined experimentally and theoretically. The temperature at the sample center increased with the humidity at relatively high pressures in the drying chamber (101.3 and 50 kPa), and the degree of the increment in the temperature with the humidity increased with the chamber pressure. The effect of the humidity on the temperature at the sample center and the drying time was insignificant at a relatively low chamber pressure (20 kPa).     

Time-series analysis of the characteristic pressure fluctuations in a conical fluidized bed with negative pressure

The negative pressure conical fluidized bed is widely used in the pharmaceutical industry. In this study, experiments based on the negative pressure conical fluidized bed are carried out by changing the material mass and particle size. The pressure fluctuation signals are analyzed by the time and the frequency domain methods. A method for absolutely characterizing the degree of the energy concentration at the main fre-quency is proposed, where the calculation is to divide the original power spectrum by the average signal power. A phenomenon where the gas velocity curve temporarily stops growing is observed when the mate-rial mass is light, and the particle size is small. The standard deviation and kurtosis both rapidly change at the minimum fluidization velocity and thus can be used to determine the flow regime, and the variation rule of the kurtosis is independent of both the material mass and particle size. In the initial fluidization stage, the dominant pressure signal comes from the material movement;with the increase in the gas veloc-ity, the power of a 2.5 Hz signal continues to increase. A method of dividing the main frequency by the aver-age cycle frequency can conveniently determine the fluidized state, and a novel concept called stable fluidized zone proposed in this paper can be obtained. Controlling the gas velocity within the stable flu-idized zone ensures that the fluidized bed consistently remains in a stable fluidized state.     

Tomographic diagnosis of gas maldistribution in gas-solid fluidized beds

Phase distribution is one of the key hydrodynamic parameters useful for the design and performance assessment of fluidized bed dryers (FBDs). It has direct influence on the drying rate, thermal efficiency, residence time distribution and degree of mixing. The quality of fluidization strongly depends on the uniformity of distribution of the fluidizing gas and the physical properties of the material to be fluidized. In the present work, gamma ray tomography (GRT) study was carried out in the form of chordal solid hold-up, which was found to be greatly influenced by the gas distributor design. The performance of a gas distributor due to the prevalent practice of operating at lower values of distributor-to-bed pressure drop ratio was characterized in a 0.15 m diameter fluidized bed dryer over a broad range of superficial gas velocity. The effects of various parameters such as solids loading, particle size and particle density were analyzed with the help of the reconstructed solid hold-up profiles. The fluidization was studied in terms of maldistribution factor (χ), a value of 5% or less can be obtained by properly designing distributor for a given bed loading, particularly for batch fluidized bed dryers. An industrial size fluidized bed dryer of 1 m diameter was also examined tomographically to obtain quantitative information on the solid hold-up distribution within the bed.     

Drying Characteristics of Carrots Immersed in a Fluidized Bed of Fluidizing Particles Under Reduced Pressure

The drying characteristics and properties (color and shrinkage) of carrots (as a representative agricultural product) were experimentally examined in a fluidized bed under reduced pressure. Dry hot air and superheated steam were used as the drying gases. Rice and carrot powders (0.125–0.355 mm in diameter) were used as the fluidizing particles, in addition to glass beads (0.12 mm in diameter).

It was confirmed that the drying rate using a fluidized bed was much higher than without a fluidized bed (hot-air drying), regardless of the type of fluidizing particles used. Under reduced pressure, both with and without a fluidized bed, the drying rate was higher than that at atmospheric pressure using hot air. The drying rate was sufficiently high for fluidized-bed drying with superheated steam, though the drying rate was higher with hot air than with superheated steam. As the drying temperature increased, the volume ratio (befor/after drying) of the sample increased. At high drying temperatures (373 and 423 K in the present study), the color of the sample changed; in other words, a heat-induced change in the properties of the carrot was observed. At a low drying temperature (333 K in the present study), the drying method did not affect the color of the carrot; i.e., the color of the dried material was maintained even in a fluidized bed under reduced pressure when the drying rate was higher.     

生物质快速热解流化床反应器气力进料特性

为探究不同工况下热解流化床反应器的气力进料特性,设计并搭建了流化床反应器气力进料冷态试验装置。生物质原料和床料分别采用落叶松颗粒和石英砂颗粒,通过试验测得了本装置的最小流化速度,研究了流化气速、喷动气速、流量比、初始静床高、石英砂粒径、落叶松粒径对流化床反应器气力进料特性的影响。试验结果表明：流化气速和喷动气速的增加均会提高进料率;流化气使床料流化并为落叶松颗粒提供进料空间,喷动气为落叶松颗粒提供动能,并平衡一部分床层压力;落叶松与石英砂粒径的增加对进料效果不利;流量比在1.9~2.7范围内进料率高且稳定性好。本文构建了生物质、床料与气体的三相流物理及数学模型,开展试验对模型进行验证,结果表明其预测误差为±13%。     

硼砂在内热式振动流化床中的干燥特性研究

采用内热式振动流化床对硼砂进行了干燥实验,考察了流化气速、进气温度和振动频率对硼砂干燥特性的影响,分析了硼砂湿含量、含水分子个数和干燥速率的变化规律。结果表明,干燥速率随着流化气速和进气温度的增加而增加,随着振动频率增加变化不大。通过实验数据得到了计算干燥速率的关联式,计算值与实验值吻合较好,误差在±20%范围内。结果可为内热式振动流化床的设计和研究提供参考。     

纳米TiO2在环隙流化床中流动特性的实验研究

在环隙流化(AFB)床中,应用实验测量技术研究了床层压降和床层膨胀曲线以及最小流化速度的变化规律.研究结果显示,在升速流化时,随着气速增大,床层压降和床层膨胀比也随之增大,当气速超过一定值时,纳米TiO2颗粒完全流化,压降波动和床层膨胀比趋于平稳.最小流化速度随着纳米TiO2质量的增加而增大.     

离心流化床初始流化状态的研究(Ⅰ)基本理论

通过简化求解离心流化床连续介质模型基本控制方程,获得了初始流化速度、压力、空隙率、空隙气速、床层膨胀和床层压降的计算方程式。理论预报的临界流化速度和床层压降与实验结果吻合得很好。揭示了离心流化床随流速增大由表面逐层初始流化;流化后各半径处流化程度不同。理论分析还表明气体压缩性的影响随着床体转速的增大而增大。     

循环流化床中C类颗粒连续干燥的研究

循环流化床(CFB)作为一种新兴反应器,其结构简单、气固接触效率高、处理量大,成为气固二相干燥应用研究的新方向.文中在自建的循环流化床(内径0.104 m×高2.35 m)内,以玉米淀粉(dp=8 μm,ρp=800 kg/m3)为C类颗粒,进行了连续干燥.实验初步研究了进料速率、进风温度及气速等操作参数对淀粉平均停留...