Synthesis of phenolic resol resins using cornstalk-derived bio-oil produced by direct liquefaction in hot-compressed phenol–water

For the synthesis of biomass-based resol resins, cornstalk powders were liquefied in a hot-compressed phenol–water (1:4, wt./wt.) medium at 300–350 °C. It was observed that essentially no phenol was reacted with the cornstalk degradation intermediates during the liquefaction process. The cornstalk-derived bio-oils contained oligomers of phenol and substituted phenols, originated primarily from the lignin component of the cornstalk feedstock. Using the cornstalk-derived bio-oils, resol resins were readily synthesized under the catalysis of sodium hydroxide. The biomass-derived resol resins were brown viscous liquids, possessing broad molecular weight distributions. In comparison with those of a conventional phenol resol resin, the properties of the bio-based resins were characterized by GPC, FTIR, DSC and TGA. The as-synthesized bio-oil resol resin exhibited typical properties of a thermosetting phenol–formaldehyde resin, e.g., exothermic curing temperatures at about 150–160 °C, and an acceptable residual carbon yield of ca 56% at 700 °C for the cured material.     

Activation energy and curing behavior of resol‐ and novolac‐type phenolic resins by differential scanning calorimetry and thermogravimetric analysis

The thermal behavior, thermal degradation kinetics, and pyrolysis of resol and novolac phenolic resins with different curing conditions, as a function of the formaldehyde/phenol (F/P) molar ratio (1.3, 1.9, and 2.5 for the resol resins and 0.5, 0.7, and 0.9 for the novolac resins) were investigated. The activation energy of the thermal reaction was studied with differential scanning calorimetry at five different heating rates (2, 5, 10, 20, and 40°C/min) between 50 and 300°C. The activation energy of the thermal decomposition was investigated with thermogravimetric analysis at five different heating rates (2, 5, 10, 20, and 40°C/min) from 30 to 800°C. The low molar ratio resins exhibited a higher activation energy than the high molar ratio resins in the curing process. This meant that less heat was needed to cure the high molar ratio resins. Therefore, the higher the molar ratio was, the lower the activation energy was of the reaction. As the thermal decomposition of the resol resins proceeded, the activation energy sharply decreased at first and then remained almost constant. The activation energy of the thermal decomposition for novolac resins with F/P = 0.5 or F/P = 0.7 was almost identical in all regions, whereas that for novolac resins with F/P = 0.9 gradually decreased as the reaction proceeded. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2589–2596, 2003     

Thermally resistant carbazole‐modified phenol–formaldehyde resins

Phenol–formaldehyde resins were modified with carbazole in order to improve their thermal resistance. Attempts to incorporate carbazole rings into novolac and resol resins were made using three methods: (1) the addition of N‐(hydroxymethyl)carbazole (HMC) into a phenol–formaldehyde mixture, (2) the addition of carbazole into a phenol–hydroxymethyl derivative of acetone mixture, where the hydroxymethyl derivative of acetone was used as formaldehyde donor, and (3) by prolonging the time of high‐temperature reaction between phenol, carbazole and formaldehyde. The temperature and time of reaction were critical for incorporation of carbazole, which successfully led to highly temperature‐resistant carbazole‐modified novolacs for the latter procedure. When carbazole was incorporated into novolac structure at a level of 8 mol%, the thermal resistance increased by 118 °C measured as 5% mass loss temperature. Other procedures led to solids containing carbazole or HMC as physical admixtures. The obtained composites revealed variable thermal resistance effects; the carbazole‐modified resol containing 9 mol% of carbazole showed 47 °C increase of thermal resistance in comparison with non‐modified resol, measured as 5% mass loss temperature. © 2015 Society of Chemical Industry     

Time–temperature–transformation cure diagrams of phenol–formaldehyde and lignin–phenol–formaldehyde novolac resins

In this study, the time–temperature– transformation (TTT) cure diagrams of the curing processes of several novolac resins were determined. Each diagram corresponded to a mixture of commercial phenol–formaldehyde novolac, lignin–phenol–formaldehyde novolac, and methylolated lignin–phenol–formaldehyde novolac resins with hexamethylenetetramine as a curing agent. Thermomechanical analysis and differential scanning calorimetry techniques were applied to study the resin gelation and the kinetics of the curing process to obtain the isoconversional curves. The temperature at which the material gelled and vitrified [the glass‐transition temperature at the gel point (_gelT_g)], the glass‐transition temperature of the uncured material (without crosslinking; T_g0), and the glass‐transition temperature with full crosslinking were also obtained. On the basis of the measured of conversion degree at gelation, the approximate glass‐transition temperature/conversion relationship, and the thermokinetic results of the curing process of the resins, TTT cure diagrams of the novolac samples were constructed. The TTT diagrams showed that the lignin–novolac and methylolated lignin–novolac resins presented lower T_g0 and _gelT_g values than the commercial resin. The TTT diagram is a suitable tool for understanding novolac resin behavior during the isothermal curing process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Impact performance of phenolic composites following thermal exposure

The notched and unnotched Izod impact properties of a series of phenolic-glass composites following thermal exposure at 180°C, 300°C, and 800°C have been investigated. Four phenolic resins; a resol, a novolac, a resol/novolac blend, and a furan-novolac/resol copolymer were used to prepare the composites. The notched and unnotched impact properties of all S-glass composites improved following thermal exposure at 180°C for times up to 28 days. The best results at 180°C were obtained for the copolymer-based composite. However, thermal exposure at 300°C for times greater than 1 day led to significant reduction in the performance of this composite. The best retention of impact properties folowing exposure at 300°C and 800°C was found for the composite made with the resol/novolac blend. The results indicate that the impact properties of phenolic composites made with modified resins, that is, a blended resol/novolac or a furan-novolac/resol copolymer resin, improve significantly. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 349–361, 1998     

Influence of the synthesis conditions on the curing behavior of phenol–urea–formaldehyde resol resins

The curing behavior of synthesized phenol–urea–formaldehyde (PUF) resol resins with various formaldehyde/urea/phenol ratios was studied with differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The results indicated that the synthesis parameters, including the urea content, formaldehyde/phenol ratio, and pH value, had a combined effect on the curing behavior. The pH value played an important role in affecting the shape of the DSC curing curves, the activation energy, and the reaction rate constant. Depending on the pH value, one or two peaks could appear in the DSC curve. The activation energy was lower when pH was below 11. The reaction rate constant increased with an increase in the pH value at both low and high temperatures. The urea content and formaldehyde/phenol ratio had no significant influence on the activation energy and rate constant. DMA showed that both the gel point and tan δ peak temperature (T_tanδ) had the lowest values in the mid‐pH range for the PUF resins. A different trend was observed for the phenol–formaldehyde resin without the urea component. Instead, the gel point and T_tanδ decreased monotonically with an increase in the pH value. For the PUF resins, a high urea content or a low formaldehyde/phenol ratio resulted in a high gel point. The effect of the urea content on T_tanδ was bigger than that on the gel point because of the reversible reaction associated with the urea component. Too much formaldehyde could lead to more reversible reactions and a higher T_tanδ value. The effects of the synthesis conditions on the rigidity of the cured network were complex for the PUF resins. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1368–1375, 2005     

Thermal behavior of elastomer–resin mixtures used as friction materials

This study looks at the thermal behavior of mixtures of nitrile‐butadiene rubber (NBR) with a resol or a novolac resin. When heated in the 200–300°C range, NBR became hard and insoluble because of exothermic curing and cyclizing chain reactions involving the double bonds of its butadiene units and the nitrile groups of its acrylonitrile units. The NBR proved to be compatible with the novolac but not the resol. Heating increased the modulus of elasticity of the mixtures, which was due to crosslinking of the resin and the rubber. Preliminary linking of the resin resulted in phase separation in the novolac and prevented curing of the rubber when the mixture was heated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1346–1351, 2001     

Effect of synthesis parameters on thermal behavior of phenol–formaldehyde resol resin

Differential scanning calorimetry (DSC) was used to investigate the influence of resin synthesis parameters on the thermal behavior of low molecular weight phenol–formaldehyde (PF) resol resins prepared with different formaldehyde/phenol (F/P) molar ratios, different sodium hydroxide/phenol (NaOH/P) molar ratios, and different catalysts. As the F/P molar ratio increased, the molecular weight and activation energy increased while the gel time, peak temperature, resin pH, and nonvolatile solids content decreased. By contrast, the molecular weight, gel time, resin pH, resin solids content, and peak temperature increased with an increasing NaOH/P molar ratio. However, the activation energy decreased with an increasing NaOH/P molar ratio. The polydispersity increased with both F/P and NaOH/P ratios. Calcium hydroxide gave a faster curing resin compared to sodium and potassium hydroxides. All DSC thermograms of this study showed just a single exothermic peak for the resins that were used. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1415–1424, 2002     

Synthesis and cure kinetics of liquefied wood/phenol/formaldehyde resins

Wood liquefaction was conducted at a 2/1 phenol/wood ratio in two different reactors: (1) an atmospheric three‐necked flask reactor and (2) a sealed Parr reactor. The liquefied wood mixture (liquefied wood, unreacted phenol, and wood residue) was further condensed with formaldehyde under acidic conditions to synthesize two novolac‐type liquefied wood/phenol/formaldehyde (LWPF) resins: LWPF1 (the atmospheric reactor) and LWPF2 (the sealed reactor). The LWPF1 resin had a higher solid content and higher molecular weight than the LWPF2 resin. The cure kinetic mechanisms of the LWPF resins were investigated with dynamic and isothermal differential scanning calorimetry (DSC). The isothermal DSC data indicated that the cure reactions of both resins followed an autocatalytic mechanism. The activation energies of the liquefied wood resins were close to that of a reported lignin–phenol–formaldehyde resin but were higher than that of a typical phenol formaldehyde resin. The two liquefied wood resins followed similar cure kinetics; however, the LWPF1 resin had a higher activation energy for rate constant k₁ and a lower activation energy for rate constant k₂ than LWPF2. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Curing of resole-type phenol–formaldehyde resin

The process of resole-type phenol–formaldehyde resins was studied by differential thermal analysis and infrared spectroscopy. It was shown that in neutral media the first reactions that occur are those between free phenol present in the resin and monosubstituted methylol phenol with free reactive positions on the benzene ring. The formation of methylene linkages is followed immediately by the condensation of methylol groups to give dibenzyl ether linkages. These are subsequently destroyed at about 210°C. It is believed that the entire curing process is governed by a free-radical mechanism. It is also shown that oxidation of the resin occurs slowly at room temperature and humidity.     

Master curve and time–temperature–transformation cure diagram of lignin–phenolic and phenolic resol resins

The aim of this work is to generate both a master curve of resol resins based on the time–temperature superposition principle and their TTT cure diagrams. The samples used for this purpose were lignin–phenolic and phenol–formaldehyde resol resins. A TMA technique was employed to study the gelation of resol resins. In addition, a DSC technique was employed to determine the kinetic parameters through the Ozawa method, which allowed us to obtain isoconversional curves from the data fit to the Arrhenius expression. Establishing the relationship between the glass‐transition temperature and curing degree allowed the determination of the vitrification lines of the resol resins. Thus, using the experimental data obtained by TMA and DSC, we generated a TTT cure diagram for each of resins studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3362–3369, 2007     

Synthesis and properties of polycyclic phosphonate resins using one-pot method under ultrasound irradiation

Novel polycyclic phosphonates were first synthesized from novolac phenol formaldehyde (PF) resins under ultrasound irradiation in the absence of phase transfer catalyst (PTC). Experimental results demonstrated that ultrasound can accelerate the cycle condensation of the novolac PF resin in good yield. The chemical structure of the synthesized polycyclics was characterized using Gel-permeation chromatography (GPC), Fourier transfer infrared (FTIR), ¹H- and ³¹P-nuclear magnetic resonance (NMR). Thermal properties of these polycyclics were determined by TG/IR analysis. The results showed that the induced cyclical phosphonate resins can greatly inhibit the oxidative weight loss of the polycyclic phosphonates, leading to very high char yields at temperatures higher than 700 °C. The char yields remained still about 4 wt.% while the weight remaining of phosphonate-free phenol formaldehyde (PF) resin was almost 0% at 600 °C. This indicates that the synthesized polycyclic phosphonates could be the potential candidates as a flame retardant for the polymers such as polycarbonate, epoxy resin and poly(ethylene terephthalate) etc.     

Highly thermally stable novolac derivatives and their properties in epoxy composites

Two diazo‐coupling novolac derivative resins (carbonyl phenyl azo novolac resin and carbonyl phenol–biphenylene azo novolac resin) were used as flame retardants. The cured resins exhibited elevated glass‐transition temperatures from 115°C (blank) to 195 and 167°C, respectively. The char yield at 800°C was increased, which elaborated the effectiveness of flame retardancy with evaluated limiting oxygen indices around 36 to 40. This was mainly attributed to the increased crosslink densities and highly aromatic contents in the modified phenol novolac derivative resins, which exhibited higher thermal degradation energies. Furthermore, the more effective flame retardancy was expected because of the loss of nitrogen during combustion. Through the evaluation of the cooperative flame retardancy in the organic/inorganic hybrid with char yield and increasing limiting oxygen index percentage, the effects of the filler showed cooperative flame retardancy only with the appropriate addition and with a difference in the crosslinking densities. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Impact of curing condition on pH and alkalinity/acidity of structural wood adhesives

Nine formulations were selected for evaluating the effect of different curing methods on pH and alkalinity or acidity of various structural wood adhesives. These included four phenol–formaldehyde (PF) resins with high pH, one phenol–resorcinol–formaldehyde (PRF) resin with intermediate pH, two melamine–urea–formaldehyde (MUF) resins, and two melamine–formaldehyde (MF) resins with low pH. The four curing methods used in the study were: (1) curing at 102–105°C for 1 h (based on CSA O112.6‐1977), (2) four‐hour curing at 66°C followed by 1‐hour curing at 150°C (based on ASTM D1583‐01), (3) curing at room temperature overnight (based on ASTM D 1583‐01), and (4) cured adhesive squeezed out from glue lines of bonded shear block samples. The effect of the different methods on pH and alkalinity/acidity of the cured adhesive depended strongly on the individual adhesives. For the PF, the alkalinity was different for the different formulations in the liquid form, while in the cured form, the difference in the alkalinity depended on the curing method used. The MF and the MUF were the adhesives most affected by the method used. In particular, the MUF showed much higher cured film pH values when cured by method 2 compared to the other three methods, while both the cured MF and MUF exhibited quite variable acidity values when cured with the different methods. The PRF showed reasonably uniform cured film pH but varying acidity values when cured with the different methods. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

氯化铵对酚醛甲阶树脂固化速率和游离甲醛含量的影响

针对酚醛树脂的固化问题,以MPF甲阶树脂为对象,酸性盐氯化铵为酸度调节剂,研究加入氯化铵后体系固化时间和游离甲醛的变化情况,并探讨了氯化铵添加量对它们的影响。结果显示,氯化铵完全可以作为酚醛甲阶树脂的固化剂；加入少量氯化铵时,固化速度就明显加快；氯化铵的加入量在0．6%～1．2%,固化时间和游离甲醛含量的减少都很明显；当氯化铵的添加量继续增加,游离甲醛含量继续减少,但对固化时同的影响很小。通过对游离甲醛的分析,确定甲醛随氯化铵添加量的变化率为0．4～0．6。     

Properties of compression‐molded plates made from wood powders impregnated with liquefied wood‐based novolak‐type phenol‐formaldehyde resins

Novolak‐type phenol‐formaldehyde (PF) resins with solution form were prepared by reacting phenol‐liquefied Cryptomeria japonica (Japanese cedar) wood with formalin in the presence of methanol. Wood powders of Albizzia falcate (Malacca albizzia) impregnated with these resins were air dried followed by an oven‐dried at 60°C. DSC analysis showed the PF resin existing in wood powders could be melted, and could be cured if hexamine was mixed and heated at high temperature. Compression‐molded plates made with PF resin impregnated woods had a high degree of curing reaction. However, compression‐molded plates hot‐pressed at 180°C for 8 min or 200°C for 5 min had better internal bonding strength and dimensional stability than others. Premixing hexamine with PF resin and impregnating into wood powders simultaneously could enhance the reactivity of PF resin, but it was not useful for improving the properties of compression‐molded plates. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Curing behavior study of polydimethylsiloxane‐modified allylated novolac/4,4′‐bismaleimidodiphenylmethane resin

The curing behavior of polydimethylsiloxane‐modified allylated novolac/4,4′‐bismaleimidodiphenylmethane resin (PDMS‐modified AN/BDM) was investigated by using Fourier transform infrared spectrometry (FTIR) and differential scanning calorimetry. The results of FTIR confirmed that the curing reactions of the PDMS‐modified AN/BDM resins, including “Ene” reaction and Diels–Alder reaction between allyl groups and maleimide groups, should be similar to those of the parent allylated novolac/4,4′‐bismaleimidodiphenylmethane (AN/BDM) resin. The results of dynamic DSC showed that the total curing enthalpy of the PDMS‐modified AN/BDM resins was lower than that of the parent resin. Incorporation of polydimethylsiloxane (PDMS) into the backbone of the allylated novolac (AN) resin favored the Claisen rearrangement reaction of allyl groups. The isothermal DSC method was used to study the kinetics of the curing process. The experimental data for the parent AN/BDM resin and the PDMS‐modified AN/BDM resins exhibited an nth‐order behavior. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of novolac‐type phenolic resins using glucose as the substitute for formaldehyde

Novel Novolac type phenolic resins were prepared using glucose as the substitute for toxic formaldehyde (a carcinogenic chemical). The resins were synthesized with varying molar ratios of phenol to glucose, catalyzed by strong acid (such as sulfuric acid) at 120–150°C. Analysis of the resins using gel permeation chromatography (GPC) and proton nuclear magnetic resonance (¹H‐NMR) showed that they were broadly distributed oligomers derived from the Fridel‐Crafts condensation of phenol and glucose. Using hexamethylenetetramine (HMTA) as the curing agent, the phenol‐glucose resins could be thermally cured and exhibited exothermic peaks at 130–180°C, typical of thermosetting phenolic resins. The cured resins showed satisfactory thermal stability, e.g., they started to decompose at >280°C with residual carbon yields of above 58% at 600°C. Based on the thermal properties, phenol‐glucose resin with a molar ratio of 1 : 0.5 is promising as it could be cured at a lower temperature (147°C) and exhibited a satisfactorily good thermal stability: it started to decompose at >300°C with a residual carbon yield of >64% at 600°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Phenolic‐epoxy matrix curable by click chemistry—synthesis,curing, and syntactic foam composite properties

Alkyne functional phenolic resin was cured by azide functional epoxy resins making use of alkyne‐azide click reaction. For this, propargylated novolac (PN) was reacted with bisphenol A bisazide (BABA) and azido hydroxy propyloxy novolac (AHPN) leading to triazole‐linked phenolic‐epoxy networks. The click cure reaction was initiated at 40–65°C in presence of Cu₂I₂. Glass transition temperature (Tg) of the cured networks varied from 70°C to 75°C in the case of BABA‐PN and 75°C to 80°C in the case of AHPN‐PN. DSC and rheological studies revealed a single stage curing pattern for both the systems. The cured BABA‐PN and AHPN‐PN blends showed mass loss above 300°C because of decomposition of the triazole rings and the novolac backbone. Silica fiber‐reinforced syntactic foam composites derived from these resins possessed comparable mechanical properties and superior impact resistance vis‐a‐vis their phenolic resin analogues. The mechanical properties could be tuned by regulating the reactant stoichiometry. These low temperature addition curable resins are suited for light weight polymer composite for related applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41254.     

Properties of phenol‐formaldehyde resins prepared from phenol‐liquefied lignin

In this study, alkaline lignin (AL), dealkaline lignin (DAL), and lignin sulfonate (SL) were liquefied in phenol with sulfuric acid (H₂SO₄) or hydrochloric acid (HCl) as the catalyst. The phenol‐liquefied lignins were used as raw materials to prepare resol‐type phenol‐formaldehyde resins (PF) by reacting with formalin under alkaline conditions. The results show that phenol‐liquefied lignin‐based PF resins had shorter gel time at 135°C and had lower exothermic peak temperature during DSC heat‐scanning than that of normal PF resin. The thermo‐degradation of cured phenol‐liquefied lignin‐based PF resins was divided into four temperature regions, similar to the normal PF resin. When phenol‐liquefied lignin‐based PF resins were used for manufacturing plywood, most of them had the dry, warm water soaked, and repetitive boiling water soaked bonding strength fitting in the request of CNS 1349 standard for Type 1 plywood. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011