Uneven gas diffusion layer intrusion in gas channel arrays of proton exchange membrane fuel cell and its effects on flow distribution

Intrusion of the gas diffusion layer (GDL) into gas channels due to fuel cell compression has a major impact on the gas flow distribution, fuel cell performance and durability. In this work, the effect of compression resulting in GDL intrusion in individual parallel PEMFC channels is investigated. The intrusion is determined using two methods: an optical measurement in both the in-plane and through-plane directions of GDL, as well as an analytical fluid flow model based on individual channel flow rate measurements. The intrusion measurements and estimates obtained from these methods agree well with each other. An uneven distribution of GDL intrusion into individual parallel channels is observed. A non-uniform compression force distribution derived from the clamping bolts causes a higher intrusion in the end channels. The heterogeneous GDL structure and physical properties may also contribute to the uneven GDL intrusion. As a result of uneven intrusion distribution, severe flow maldistribution and increased pressure drop have been observed. The intrusion data can be further used to determine the mechanical properties of GDL materials. Using the finite element analysis software program ANSYS, the Young's modulus of the GDL from these measurements is estimated to be 30.9 MPa.     

A comprehensive assessment on the durability of gas diffusion electrode materials in PEM fuel cell stack

Polymer electrolyte membrane (PEM) fuel cell is the most promising among the various types of fuel cells. Though it has found its applications in numerous fields, the cost and durability are key barriers impeding the commercialization of PEM fuel cell stack. The crucial and expensive component involved in it is the gas diffusion electrode (GDE) and its degradation, which limits the performance and life of the fuel cell stack. A critical analysis and comprehensive understanding of the structural and functional properties of various materials involved in the GDE can help us to address the related durability and cost issues. This paper reviews the key GDE components, and in specific, the root causes influencing the durability. It also envisages the role of novel materials and provides a critical recommendation to improve the GDE durability.     

A novel method for preparing proton exchange membrane fuel cell electrodes by the ultrasonic-spray technique

A novel ultrasonic-spray method for preparing gas diffusion electrodes (GDEs) for proton exchange membrane fuel cell (PEMFC) is described. Platinum (Pt) loaded on Nafion^®-bonded GDEs were prepared by the ultrasonic-spray method on various commercial woven and non-woven gas diffusion layers (GDLs) at several Pt loadings in the range of 0.40-0.05 mg cm⁻². The ultrasonic-sprayed GDEs were tested and compared to commercial and hand-painted GDEs. It was found that the GDEs prepared by the ultrasonic-spray method exhibited better performances compared to those prepared by the hand-painting technique, especially at low Pt loadings. GDEs fabricated by the ultrasonic-spray method with a platinum loading of 0.05 mg cm⁻² exhibited a peak power rating of 10.9 W mg⁻¹ compared to 9.8 W mg⁻¹ for hand-painted GDEs. For all experiments using various GDLs, Sigracet SGL 10BC exhibited the best performance with a peak power of 0.695 W cm⁻².     

Experimental analysis of internal gas flow configurations for a polymer electrolyte membrane fuel cell stack

The internal gas distribution system utilised for supplying fresh reactants and removing reaction products from the individual cells of a fuel cell stack can be designed in a parallel, a serial or a mixture of parallel and serial gas flow configuration. In order to investigate the interdependence between the internal stack gas distribution configuration and single cell as well as overall stack performance, a small laboratory-scale fuel cell stack consisting of identical unit cells was subject to operation with different gas distribution configurations and different operating parameters. The current/voltage characteristics measured with the different gas distribution configurations are analysed and compared on unit cell- as well as on stack-level. The results show the significant impact of the internal stack gas distribution system on operation and performance of the individual unit cells and the overall stack.     

Heat and mass transfer analysis in single cell of PEFC using different PEM and GDL at higher temperature

According to the H₂ and fuel cell road map in Japan, the target operating temperature of polymer electrolyte fuel cell (PEFC) should be 90 °C from 2020 to 2025. In this study, the impact of polymer electrolyte membrane (PEM) and gas diffusion layer (GDL)'s thickness on heat and mass transfer characteristics as well as power generation performance of PEFC is investigated at operating temperature of 90 °C. The in-plane temperature distributions on anode and cathode separator are also measured using thermograph. As a result, it is observed that the increase in power from 1 W to 5 W at the current density of 0.80 A/cm² as well as even temperature distribution within 1 °C can be obtained at operating temperature of 90 °C by decrease in GDL's thickness from 190 μm to 110 μm. In addition, the power is increased from 3 W to 4 W at the current density of 0.80 A/cm² operated at 90 °C by decrease in the PEM's thickness from 127 μm to 25 μm.     

A numerical investigation of the effects of GDL compression and intrusion in polymer electrolyte fuel cells (PEFCs)

The purpose of this work is to numerically investigate the effects of non-uniform compression of the gas diffusion layer (GDL) and GDL intrusion into a channel due to the channel/rib structure of the flow-field plate. The focus is placed on accurately predicting two-phase transport between the compressed GDL near the ribs and uncompressed GDL near the channels, and its associated effects on cell performance. In this paper, a GDL compression model is newly developed and incorporated into a comprehensive three-dimensional, two-phase PEFC model developed earlier. To assess solely the effects of GDL compression and intrusion, the new fuel cell model is applied to a simple single-straight channel fuel cell geometry. Numerical simulations with different levels of GDL compression and intrusion are carried out and simulation results reveal that the effects of GDL compression and intrusion considerably increase the non-uniformity, particularly, the in-plane gradient in liquid saturation, oxygen concentration, membrane water content, and current density profiles that in turn results in significant ohmic and concentration polarizations. The present three-dimensional GDL compression model yields realistic species profiles and cell performance that help to identify the optimal MEA, gasket, and flow channel designs in PEFCs.     

An impedance study for the anode micro-porous layer in an operating direct methanol fuel cell

This study presents the benefit to an operating direct methanol fuel cell (DMFC) by coating a micro-porous layer (MPL) on the surface of anode gas diffusion layer (GDL). Taking the membrane electrode assembly (MEA) with and without the anodic MPL structure into account, the performances of the two types of MEA are evaluated by measuring the polarization curves together with the specific power density at a constant current density. Regarding the cell performances, the comparisons between the average power performances of the two different MEAs at low and high current density, various methanol concentrations and air flow rates are carried out by using the electrochemical impedance spectroscopy (EIS) technique. In contrast to conventional half cell EIS measurements, both the anode and cathode impedance spectra are measured in real-time during the discharge regime of the DMFC. As comparing each anode and cathode EIS between the two different MEAs, the influences of the anodic MPL on the anode and cathode reactions are systematically discussed and analyzed. Furthermore, the results are used to infer complete and reasonable interpretations of the combined effects caused by the anodic MPL on the full cell impedance, which correspond with the practical cell performance.     

The effect of materials on proton exchange membrane fuel cell electrode performance

This paper describes the optimisation in the fabrication materials and techniques used in proton exchange membrane fuel cell (PEMFC) electrodes. The effect on the performance of membrane electrode assemblies (MEAs) from the solvents used in producing catalyst inks is reported. Comparison in MEA performances between various gas diffusion layers (GDLs) and the importance of microporous layers (MPLs) in gas diffusion electrodes (GDEs) are also shown. It was found that the best performances were achieved for GDEs using tetrahydrofuran (THF) as the solvent in the catalyst ink formulation and Sigracet 10BC as the GDL. The results also showed that our in-house painted GDEs were comparable to commercial ones (using Johnson Matthey HiSpec™ and E-TEK catalysts).     

Development of shut-down process for a proton exchange membrane fuel cell

Several different shut-down procedures were carried out to reduce the degradation of membrane electrode assembly (MEA) in a proton exchange membrane fuel cell (PEMFC). The effects of close/open state of outlets of a single cell and application of a dummy load during the shut-down on the degradation of the MEA were investigated. Also, we elucidated the relationship between the thickness of the electrolyte membrane and the degradation of the MEA for different shut-down procedures. When a thin electrolyte membrane was used, the closer of outlets mitigated the degradation during on/off operation. For the thicker electrolyte membrane, the dummy load which eliminates residual hydrogen and oxygen in the electrodes should be applied to lower the degradation.     

The effects of non-uniform distribution of catalyst loading on polymer electrolyte membrane fuel cell performance

The catalyst layers are the most important part of the polymer electrolyte membrane (PEM) fuel cells, and the cell performance is highly related to its structure. The gas diffusion layers (GDLs) are also the essential components of the PEM fuel cell since the reactants should pass through these layers. Model prediction shows that electrical current in catalyst layer is non-uniform, influenced by the channel-land geometry. In addition, the compression effect of GDLs and water generation due to the electrochemical reaction may cause non-uniformity in porosity and, therefore, increases the non-uniformity in reactant concentration in GDL/catalyst layer interface. Simulation results suggest that non-uniform catalyst loading distribution in the catalyst layer will improve the performance of the whole catalyst layer by diminishing the variation in current density.     

Simulation and experimental analysis of the clamping pressure distribution in a PEM fuel cell stack

High performance and efficiency are often reported in single-cell polymer electrolyte membrane (PEM) fuel cell (FC) experiments. This however, can reduce substantially when moving from single-cell experiments to multiple cells. Fuel cell performance is degraded for many reasons when adding cells, but; possibly the most important, is contact resistance between the bipolar plate and gas diffusion layer (GDL). Contact resistance is in direct relation to the clamping configuration and clamping pressure applied to a FC stack. Simulation of a single cell and 16-cell FC was performed at various clamping pressures resulting in detailed 3D plots of stress and deformation. The stress on the GDL, for any value of clamping pressure simulated in this study, is around 1.5 MPa for the 16-cell stack and around 4 MPa in single cell simulations. Experimental testing of clamping pressure effects was performed on a 16-cell stack by placing a thin pressure-sensitive film between GDL and bipolar plate. Clamping pressure was applied using various loads, durations, and two types of GDLs. The results from experimental testing show that pressure on the GDL is in the range of 0–2.5 MPa. When using rectangular cells, experimental results show nearly zero pressure in the center of each cell and the center cells of the stack, regardless of clamping method.     

Improvement of fuel cell performances through the enhanced dispersion of the PTFE binder in electrodes for use in high temperature polymer electrolyte membrane fuel cells

In high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs), it is important that the structure of the electrode catalyst layer is formed uniformly. To achieve this, the binder must be well dispersed; however, polytetrafluoroethylene (PTFE), which is commonly employed in the preparation of HT-PEMFCs, is difficult to disperse during electrode manufacture due to its high hydrophobicity. In this study, we fabricate electrodes containing a surfactant to improve the dispersion of the PTFE binder and to enhance reproducibility during electrode manufacture. The electrodes are commonly prepared via a bar coating method, which is known to exhibit poor dispersion due to the small amounts of solvent employed compared to the spraying method. We then compare the properties of the obtained electrodes prepared in the presence and absence of the surfactant through physical and electrochemical characterization. It is found that the electrode containing the surfactant is structurally superior, and its single cell performance is significantly higher (i.e., 0.65 V at 0.2 Am cm⁻²). The single cells are suitable for operation at 150 °C using H₂/air at atmospheric pressure and a total platinum loading of 2.0 mg cm⁻².     

Semi-analytical proton exchange membrane fuel cell modeling

Mathematical techniques are presented which allow for analytical solutions of the catalyst layer transport and electrochemical problem in PEM fuel cells. These techniques transform the volumetric reaction terms to boundary flux terms, thereby eliminating the need for computational solving of the catalyst layer problem. The result is a semi-analytical fuel cell model—a computational model that entails analytical rather than computational catalyst layer solutions. This helps to alleviate the meshing difficulties inherent in the catalyst layers caused by large geometric aspect ratios, and hence reduce the computational requirements for fuel cell models.     

Liquid water breakthrough pressure through gas diffusion layer of proton exchange membrane fuel cell

The dynamic behavior of liquid water transport through the gas diffusion layer (GDL) of the proton exchange membrane fuel cell is studied with an ex-situ approach. The liquid water breakthrough pressure is measured in the region between the capillary fingering and the stable displacement on the drainage phase diagram. The variables studied are GDL thickness, PTFE/Nafion content within the GDL, GDL compression, the inclusion of a micro-porous layer (MPL), and different water flow rates through the GDL. The liquid water breakthrough pressure is observed to increase with GDL thickness, GDL compression, and inclusion of the MPL. Furthermore, it has been observed that applying some amount of PTFE to an untreated GDL increases the breakthrough pressure but increasing the amount of PTFE content within the GDL shows minimal impact on the breakthrough pressure. For instance, the mean breakthrough pressures that have been measured for TGP-060 and for untreated (0 wt.% PTFE), 10 wt.% PTFE, and 27 wt.% PTFE were 3589 Pa, 5108 Pa, and 5284 Pa, respectively.     

Numerical analysis of the manipulated high performance catalyst layer design for polymer electrolyte membrane fuel cell

A two‐dimensional, multiphase, non‐isothermal numerical model was used to investigate the effect of the high performance catalyst layer (CL) design. Microstructure‐related parameters were studied on the basis of the agglomerate model assumption. A conventional CL design (uniform Pt/C composition, e.g., 40 wt%) was modified into two sub‐layers with two different Pt/C compositions (in this study, 40 and 80 wt%). The performance of sub‐layers with different CL designs is shown to be different. Simulation results show that substituting part of the Pt/C 40 wt% with Pt/C 80 wt% increases the cell performance. It was found that factors including proton conductivity, open circuit voltage, and sub‐layer thickness have a significant impact on overall cell performance. Different water distribution for different membrane electrode assembly designs was also observed in the simulation results. More liquid water accumulation inside the membrane electrode assembly is seen when the Pt/C 80 wt% sub‐layer is next to the gas diffusion layer. Finally, several key design parameters for the proposed high performance CL design including agglomerate radius, Nafion thin film thickness, and the Nafion volume fraction within the agglomerate in terms of CL fabrication were identified on the basis of our simulation results. Copyright © 2014 John Wiley & Sons, Ltd.     

Controlling gas diffusion layer oxidation by homogeneous hydrophobic coating for polymer electrolyte fuel cells

Reduced production costs and enhanced durability are necessary for practical application of polymer electrolyte fuel cells. There has been a great deal of concern about degradation of the gas diffusion layer located outside the membrane electrode assembly. However, very few studies have been carried out on the degradation process, and no suitable methods for improving the durability of the cell have been found.In this work, the influence on the cell performance and factors involved in the degradation of the gas diffusion layer has been clarified through power generation tests.Long-term power generation tests on single cells for 6000 h were carried out under high humidity conditions with homogeneous and inhomogeneous hydrophobic coating gas diffusion layers. The results showed that the increase in the diffusion overvoltage from the gas diffusion layer could be controlled by the use of a homogeneous coating. Post-analyses indicated that this occurred by controlling oxidation of the carbon fiber.     

Performance enhancement of membrane electrode assemblies with plasma etched polymer electrolyte membrane in PEM fuel cell

In this work, a surface modified Nafion 212 membrane was fabricated by plasma etching in order to enhance the performance of a membrane electrode assembly (MEA) in a polymer electrolyte membrane fuel cell. Single-cell performance of MEA at 0.7 V was increased by about 19% with membrane that was etched for 10 min compared to that with untreated Nafion 212 membrane. The MEA with membrane etched for 20 min exhibited a current density of 1700 mA cm⁻² at 0.35 V, which was 8% higher than that of MEA with untreated membrane (1580 mA cm⁻²). The performances of MEAs containing etched membranes were affected by complex factors such as the thickness and surface morphology of the membrane related to etching time. The structural changes and electrochemical properties of the MEAs with etched membranes were characterized by field emission scanning electron microscopy, Fourier transform-infrared spectrometry, electrochemical impedance spectroscopy, and cyclic voltammetry.     

Effect of cell compression on the performance of a non–hot-pressed MEA for PEMFC

In this study, the effect of cell compression on the performance of a non–hot-pressed membrane electrode assembly (MEA) for a polymer electrolyte membrane fuel cell (PEMFC) is presented. The MEA is made without hot pressing, by carefully placing the gas diffusion electrodes (GDEs) and a membrane in a fuel cell fixture. Cell performance is assessed at five different compression ratios between 3.6% and 47.8%. It has been shown that ohmic resistance of the cell, mass transport resistance of reactants, charge transfer resistance at electrode, and overall cell performance are strongly dependent on the cell compression. On increasing the cell compression gradually, cell performance improves initially, reaches the best, and then deteriorates. The cell performance is assessed at fully humidified condition and at dry condition. Optimum cell performances are obtained at compression ratios of 14.2% and 25.7% for 100% relative humidity (RH) and 50% RH, respectively. It is also found that the cell with proper compression and at fully humidified conditions can deliver similar performance to a conventional hot-pressed MEA. Finally, it is shown that after the tests, GDEs can be peeled out, and the membrane inspection can be done as a postexperimental analysis.