S-band low noise amplifier using 1μm InGaAs/InAlAs/InP pHEMT

正This paper discusses the design of a wideband low noise amplifier(LNA) in which specific architecture decisions were made in consideration of system-on-chip implementation for radio-astronomy applications.The LNA design is based on a novel ultra-low noise InGaAs/InAlAs/InP pHEMT.Linear and non-linear modelling of this pHEMT has been used to design an LNA operating from 2 to 4 GHz.A common-drain in cascade with a common source inductive degeneration,broadband LNA topology is proposed for wideband applications.The proposed configuration achieved a maximum gain of 27 dB and a noise figure of 0.3 dB with a good input and output return loss(S_(11)—10 dB,S_(22)—11 dB).This LNA exhibits an input 1-dB compression point of-18 dBm,a third order input intercept point of 0 dBm and consumes 85 mW of power from a 1.8 V supply.     

一种低于1dB噪声系数的单片集成GNSS低噪声放大器

A monolithic integrated low noise amplifier(LNA) based on a SiGe HBT process for a global navigation satellite system(GNSS) is presented. An optimizing strategy of taking parasitic capacities at the input node into consideration is adopted and a method and design equations of monolithically designing the LC load and the output impedance matching circuit are introduced. The LNA simultaneously reaches excellent noise and input/output impedance matching. The measurement results show that the LNA gives an ultra-low noise figure of 0.97 dB, a power gain of 18.6 dB and a three-order input intermodulation point of..6 dBm at the frequency of 1.575 GHz. The chip consumes 5.4 mW from a 1.8 V source and occupies 600×650 μm2 die area.     

Design of a 24–40 GHz balanced low noise amplifier using Lange couplers

A wide band （24–40 GHz） fully integrated balanced low noise amplifier （LNA） using Lange couplers was designed and fabricated with a 0.15 μm pseudomorphic HEMT （pHEMT） technology. A new method to design a low-loss and high-coupling Lange coupler for wide band application in microwave frequency was also presented. This Lange coupler has a minimum loss of 0.09 dB and a maximum loss of 0.2 dB over the bandwidth from 20 to 45 GHz. The measured results show that the realized four-stage balanced LNA using this Lange coupler exhibites a noise figure （NF） of less than 2.7 dB and the maximum gain of 30 dB; moreover, a noticeably improved reflection performance is achieved. The input VSWR and the output VSWR are respectively less than 1.45 and 1.35 dB across the 24–40 GHz frequency range.     

Research on optimizing the noise figure of low noise amplifier method via bias and frequency

In this paper,we present the design of an integrated low noise amplifier(LNA)for wireless local area network(WLAN)applications in the 5.15-5.825 GHz range using a SiGe BiCMOS technology.A novel method that can determine both the optimum bias point and the frequency point for achieving the minimum noise figure is put forward.The method can be used to determine the optimum impedance over a relevant wider operating frequency range.The results show that this kind of optimizing method is more suitable for the WLAN circuits design.The LNA gain is optimized and the noise figure(NF)is reduced.This method can also achieve the noise match and power match simultaneously.This proposal is applied on designing a LNA for IEEE 802.11a WLAN.The LNA exhibits a power gain large than 16 dB from 5.15 to 5.825 GHz range.The noise figure is lower than 2 dB.The OIP3 is 8 dBm.Also the LNA is matched to 50 Ω input impedance with 6 mA DC current for differential design.     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

A Systematical Approach for Noise in CMOS LNA

A systematic approach is used to analyze the noise in CMOS low noise amplifier(LNA),including channel noise and induced gate noise in MOS devices.A new analytical formula for noise figure is proposed.Based on this formula,the impacts of distributed gate resistance and intrinsic channel resistance on noise performance are discussed.Two kinds of noise optimization approaches are performed and applied to the design of a 5.2GHz CMOS LNA.     

一款采用跨导增强技术的新型宽带低噪声放大器

A new broadband low-noise amplifier （LNA） is proposed. The conventional common gate （CG） LNA exhibits a relatively high noise figure, so active gin-boosting technology is utilized to restrain the noise generated by the input transistors and reduce the noise figure. Theory, simulation and measurement are shown. An implemented prototype using 0.13 μm CMOS technology is evaluated using on-wafer probing. S11 and S22 are below -10 dB across 0.1-5 GHz. Measurements also show a gain of 18.3 dB with a 3 dB bandwidth from 100 MHz to 2.1 GHz and an ⅡP3 of-7 dBm at 2 GHz. The measured noise figure is better than 2.5 dB below 2.1 GHz, is better than 4.5 dB below 5 GHz, and at 500 MHz, it gets its minimum value 1.8 dB. The LNA consumes 9 mA from 1.5 V supply and occupies an area of 0.04 mm^2.     

一种新颖的低噪声放大器的噪声优化方法

This paper proposes a novel noise optimization technique.The technique gives analytical formulae for the noise performance of inductively degenerated CMOS low noise amplifier（LNA）circuits with an ideal gate inductor for a fixed bias voltage and nonideal gate inductor for a fixed power dissipation,respectively,by mathematical analysis and reasonable approximation methods.LNA circuits with required noise figure can be designed effectively and rapidly just by using hand calculations of the proposed formulae.We design a 1.8 GHz LNA in a TSMC 0.25 μm CMOS process.The measured results show a noise figure of 1.6 dB with a forward gain of 14.4 dB at a power consumption of 5 mW,demonstrating that the designed LNA circuits can achieve low noise figure levels at low power dissipation.     

0.9GHz和2.4GHz 双频段 SiGe HBT 低噪声放大器的设计

This paper presents design and implementation of a dual-band LNA using a 0.35μm SiGe HBT process for 0.9 GHz GSM and 2.4 GHz WLAN applications.PCB layout parasitic effects have a vital effect on circuit performance and are accounted for using electro-magnetic（EM） simulation.Design considerations of noise decoupling, input/output impedance matching,and current reuse are described in detail.At 0.9/2.4 GHz,gain and noise figure are 13/16 dB and 4.2/3.9 dB,respectively.Both S₁₁ and S₂₂ are below -10 dB.Power dissipation is 40 mW at 3.5 V supply.     

A full W-band low noise amplifier module for millimeter-wave applications

A full W-band Low Noise Amplifier (LNA) Module is designed and fabricated in this letter. A broadband transition is introduced in this module. The proposed transition is designed, optimized based on the results from numerical simulations. The results show that 1 dB bandwidth of the transition ranges from 61 to 117 GHz. For the purpose of verification, two transitions in back-to-back connection are measured. The results show that transmission loss is only about 0.9-1.7dB. This transition is used to interface integrated circuits to waveguide components. The characteristic of the LNA module is measured after assembly. It exhibits a broad bandwidth of 75 to 110 GHz , has a small signal gain above 21 dB. The noise figure is lower than 5dB throughout the entire W-band (below 3 dB from 89 to 95GHz) at a room temperature. The proposed LNA module exhibits potential for millimeter wave applications due to its high small signal gain, low noise, and low dc power consumption     

A 0.18μm CMOS gain-switched LNA and mixer with large dynamic range

A 2.4GHz 0.18μm CMOS gain-switched single-end Low Noise Amplifier （LNA） and a passive mixer with no external balun for near-zero-IF （Intermediate Frequency）/RF （Radio Frequency） applications are described. The LNA, fabricated in the 0.18μm 1P6M CMOS technology, adopts a gain-switched technique to increase the linearity and enlarge the dynamic range. The mixer is an IQ-based passive topology. Measurements of the CMOS chip are performed on the FR-4 PCB and the input is matched to 50Ω. Combining LNA and mixer, the front-end measured performances in high gain state are： -15dB of Sll, 18.5dB of voltage gain, 4.6dB of noise figure, 15dBm of IIP3, 85dBm to -10dBm dynamic range. The full circuit drains 6mA from a 1.8V supply.     

A 0.18μm CMOS Gilbert low noise mixer with noise cancellation

正This paper presents a broadband Gilbert low noise mixer implemented with noise cancellation technique operating between 10 MHz and 0.9 GHz.The Gilbert mixer is known for its perfect port isolation and bad noise performance.The noise cancellation technique of LNA can be applied here to have a better NF.The chip is implemented in SMIC 0.18μm CMOS technology.Measurement shows that the proposed low noise mixer has a 13.7-19.5 dB voltage gain from 10 MHz to 0.9 GHz,an average noise figure of 5 dB and a minimum value of 4.3 dB.The core area is 0.6 x 0.45 mm~2.     

Design and optimization of CMOS LNA with ESD protection for 2.4 GHz WSN application

A new optimization method of a source inductive degenerated low noise amplifier(LNA) with electrostatic discharge protection is proposed.It can achieve power-constrained simultaneous noise and input matching. An analysis of the input impedance and the noise parameters is also given.Based on the developed method,a 2.4 GHz LNA for wireless sensor network application is designed and optimized using 0.18-μm RF CMOS technology. The measured results show that the LNA achieves a noise figure of 1.59 dB,a power gain of 14.12 dB, an input 1 dB compression point of-8 dBm and an input third-order intercept point of 1 dBm.The DC current is 4 mA under a supply of 1.8 V.     

A wideband LNA employing gate-inductive-peaking and noise-canceling techniques in 0.18μm CMOS

正This paper presents a wideband low noise amplifier(LNA) for multi-standard radio applications.The low noise characteristic is achieved by the noise-canceling technique while the bandwidth is enhanced by gateinductive -peaking technique.High-frequency noise performance is consequently improved by the flattened gain over the entire operating frequency band.Fabricated in 0.18μm CMOS process,the LNA achieves 2.5 GHz of -3 dB bandwidth and 16 dB of gain.The gain variation is within±0.8 dB from 300 MHz to 2.2 GHz.The measured noise figure(NF) and average HP3 are 3.4 dB and -2 dBm,respectively.The proposed LNA occupies 0.39 mm2 core chip area.Operating at 1.8 V,the LNA drains a current of 11.7 mA.     

可重构双频段低噪声放大器的设计和实现

A reconfigurable dual-band LNA is presented. The LNA employs switching capacitors and circuit in to realize the dual-band operation. These methodologies are used to design and implement a reconfigurable LNA for IMT-A and UWB application. The LNA is implemented using TSMC-0.13 μm CMOS technology. Measured performance shows an input matching of better than -13.5 dB, a voltage gain of 18-22.8 dB, with an NF of 4.3-4.7 dB in the band of 3.4-3.6 GHz, and an input matching of better than -9.7 dB, a voltage gain of 14.7-22.4 dB, and with an NF of 3.7-4.9 dB in the band of 4.2-4.8 GHz. According to the measure results, the proposed LNA achieves dual-band operation, and it proves the feasibility of the proposed topology.     

A CMOS variable gain LNA for UWB receivers

A CMOS variable gain low noise amplifier(LNA) is presented for 4.2-4.8 GHz ultra-wideband application in accordance with Chinese standard.The design method for the wideband input matching is presented and the low noise performance of the LNA is illustrated.A three-bit digital programmable gain control circuit is exploited to achieve variable gain.The design was implemented in 0.13-μm RF CMOS process,and the die occupies an area of 0.9 mm~2 with ESD pads.Totally the circuit draws 18 mA DC current from 1.2 V DC supply,the LNA exhibits minimum noise figure of 2.3 dB,S(1,1) less than -9 dB and S(2,2) less than -10 dB.The maximum and the minimum power gains are 28.5 dB and 16 dB respectively.The tuning step of the gain is about 4 dB with four steps in all.Also the input 1 dB compression point is -10 dBm and input third order intercept point(IIP3) is -2 dBm.     

A low power high gain gain-controlled LNAC＋mixer for GNSS receivers

A low power high gain gain-controlled LNAC+mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load.Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNACmixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNAC+mixer, a previous low power LNAC+mixer, and the proposed LNAC+mixer are presented. The circuit is implemented in 0.18 m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2and consumes 2 mA current under 1.8 V supply.     

A 0.18 μm CMOS Gilbert low noise mixer with noise cancellation

This paper presents a broadband Gilbert low noise mixer implemented with noise cancellation technique operating between 10 MHz and 0.9 GHz. The Gilbert mixer is known for its perfect port isolation and bad noise performance. The noise cancellation technique of LNA can be applied here to have a better NF. The chip is implemented in SMIC 0.18 μm CMOS technology. Measurement shows that the proposed low noise mixer has a 13.7-19.5 dB voltage gain from 10 MHz to 0.9 GHz, an average noise figure of 5 dB and a minimum value of 4.3 dB. The core area is 0.6 × 0.45 mm².     

用于ZigBee的2.4GHz低功耗双增益低噪声放大器

This paper presents a fully differential dual gain low noise amplifier（DGLNA） for low power 2.45-GHz ZigBee/IEEE 802.15.4 applications.The effect of input parasitics on the inductively degenerated cascode LNA is analyzed.Circuit design details within the guidelines of the analysis are presented.The chip was implemented in SMIC 0.18-μm 1P6M RF/mixed signal CMOS process.The DGLNA achieves a maximum gain of 8 dB and a minimum gain of 1 dB with good input return loss.In high gain mode, the measured noise figure（NF） is 2.3-3 dB in the whole 2.45-GHz ISM band.The measured 1-dB compression point, IIP3 and IIP2 is-9, 1 and 33 dBm, respectively.The DGLNA consumes 2 mA of current from a 1.8 V power supply.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.