MOS devices with tetragonal ZrO2 as gate dielectric formed by annealing ZrO2/Ge/ZrO2 laminate

A Ge-stabilized tetragonal ZrO₂ (t-ZrO₂) film with permittivity (κ) of 36.2 was formed by depositing a ZrO₂/Ge/ZrO₂ laminate and a subsequent annealing at 600 °C, which is a more reliable approach to control the incorporated amount of Ge in ZrO₂. On Si substrates, with thin SiON as an interfacial layer, the SiON/t-ZrO₂ gate stack with equivalent oxide thickness (EOT) of 1.75 nm shows tiny amount of hysteresis and negligible frequency dispersion in capacitance-voltage (C-V) characteristics. By passivating leaky channels derived from grain boundaries with NH₃ plasma, good leakage current of 4.8 × 10⁻⁸ A/cm² at V_g = V_fb − 1 V is achieved and desirable reliability confirmed by positive bias temperature instability (PBTI) test is also obtained.     

Effect of H2O evolving from TEOS based SiO2 film on the EEPROM cell characteristic

In this paper, we investigate the effect of water (H₂O) molecules evolving from silicon dioxide (SiO₂) film deposited by low pressure chemical vapor deposition (LPCVD) at 670 °C on the transistor characteristic of an electrically erasable programmable read only memory (EEPROM) cell. Fourier Transform Infra red (FT-IR) analysis reveals that H₂O is captured during film deposition and diffused to silicon surface during high thermal processing. The diffused H₂O molecules lower threshold voltage (V_t) of cell transistor and, thus, leakage current of the cell transistor is increased. In erased cell, V_t lowering is 0.25 V in which it increases leakage current of cell transistor from 1 to 100 pA. This results in the lowering of high voltage margin of a 512 Kb EEPROM from 2.8 to 2.6 V at 85 °C.     

Effects of annealing schedule on orientations of Bi3.2Nd0.8Ti3O12 ferroelectric films prepared by metalorganic solution deposition

Fatigue-free Bi_3.2Nd_0.8Ti₃O₁₂ ferroelectric thin films were successfully prepared on p-Si(1 1 1) substrate using metalorganic solution deposition process. The orientation and formation of thin film under different annealing schedules were studied using XRD and AFM. XRD analysis indicated that (2 0 0)-oriented films with degree of orientation of I₍₂₀₀₎/I₍₁₁₇₎ = 2.097 and 0.466 were obtained by preannealing the film at 400 °C for 10 min followed by rapid thermal annealing at 700 °C for 3 min, 10 min and 20 min, respectively, (0 0 8)-oriented film with degree of orientation of I₍₀₀₈₎/I₍₁₁₇₎ = 1.706 were obtained by rapid thermal annealing the film at 700 °C for 3 min without preannealing, and (0 0 8)-oriented film with degree of orientation of I₍₀₀₈₎/I₍₁₁₇₎ = 0.719 were obtained by preheating the film from room temperature to 700 °C at 20 °C/min followed by annealing for 10 min. The a-axis and c-axis orientation decreased as increase in annealing time due to effects of (1 1 1)-oriented substrate. AFM analysis further indicated that preannealing at 400 °C for 10 min followed by rapid thermal annealing at 700 °C for 3 min resulted in formation of platelike crystallite parallel to substrate surface, however rapid thermal annealing at 700 °C for 3 min without preannealing resulted in columnar crystallite perpendicular to substrate surface.     

Characteristics of metal-oxide-semiconductor (MOS) device with Er metal gate on SiO2 film

We have investigated the structural and electrical properties of metal-oxide-semiconductor (MOS) devices with Er metal gate on SiO₂ film. Rapid thermal annealing (RTA) process leads to the formation of a high-k Er-silicate gate dielectric. The in situ high-voltage electron microscopy (HVEM) results show that thermally driven Er diffusion is responsible for the decrease in equivalent oxide thickness (EOT) with an increase in annealing temperature. The effective work function (Φ_m,eff) of Er metal gate, extracted from the relations of EOT versus flat-band voltage (V_FB), is calculated to be ∼2.86 eV.     

Investigation of Ta2O5/SiO2/4H-SiC MIS capacitors

Tantalum pentoxide (Ta₂O₅) deposited by pulsed DC magnetron sputtering technique as the gate dielectric for 4H-SiC based metal-insulator-semiconductor (MIS) structure has been investigated. A rectifying current-voltage characteristic was observed, with the injection of current occurred when a positive DC bias was applied to the gate electrode with respect to the n type 4H-SiC substrate. This undesirable behavior is attributed to the relatively small band gap of Ta₂O₅ of around 4.3 eV, resulting in a small band offset between the 4H-SiC and Ta₂O₅. To overcome this problem, a thin thermal silicon oxide layer was introduced between Ta₂O₅ and 4H-SiC. This has substantially reduced the leakage current through the MIS structure. Further improvement was obtained by annealing the Ta₂O₅ at 900 °C in oxygen. The annealing has also reduced the effective charge in the dielectric film, as deduced from high frequency C-V measurements of the Ta₂O₅/SiO₂/4H-SiC capacitors.     

Pentacene thin-film transistors with sol-gel derived amorphous Ba0.6Sr0.4TiO3 gate dielectric

An amorphous Ba_0.6Sr_0.4TiO₃ (BST) film with the thickness of 200 nm was deposited on indium-tin-oxide (ITO)-coated glass substrate through sol-gel route and post-annealing at 500 °C. The dielectric constant of the BST film was determined to be 20.6 at 100 kHz by measuring the Ag/BST/ITO parallel plate capacitor, and no dielectric tunability was observed with the bias voltage varying from −5 to 5 V. The BST film shows a dense and uniform microstructure as well as a smooth surface with the root-mean-square (RMS) roughness of about 1.4 nm. The leakage current density was found to be 3.5 × 10⁻⁸ A/cm² at an applied voltage of −5 V. The transmittance of the BST/ITO/glass structure is more than 70% in the visible region. Pentacene based transistor using the as-prepared BST film as gate insulator exhibits a low threshold voltage of −1.3 V, the saturation field-effect mobility of 0.68 cm²/Vs, and the current on/off ratio of 3.6 × 10⁵. The results indicate that the sol-gel derived BST film is a promising high-k gate dielectric for large-area transparent organic transistor arrays on glass substrate.     

Resistive switching characteristics of Sm2O3 thin films for nonvolatile memory applications

This study investigates a sputtered Sm₂O₃ thin film to apply into a resistive random access memory device. The proposed device exhibits a stable resistance ratio of about 2.5 orders after 10⁴ cycling bias pulses and no degradation for retention characteristics monitored after an endurance test at 85 °C. The conduction mechanisms for low and high resistance states are dominated by ohmic behavior and trap-controlled space-charge limited current, respectively. The resistance switching is ascribed to the formation/rupture of conductive filaments.     

Reducing Cu diffusion in SiCOH low-k films by O2 plasma treatment

This work investigates the Cu diffusion in SiCOH low dielectric constant films treated by O₂ plasma. By capacitance–voltage and current-voltage measurement, and thermal stress analysis, it is found that the O₂ plasma surface treatment of SiCOH films can lead to the decrease of flatband voltage shift ΔV_FB, the increase of activation energy E_a, and the decrease of leakage current. The small ΔV_FB and lower leakage current indicate the weak Cu diffusion. The increase of active energy means the reducing of fast Cu ions surface diffusion through the interconnected pores structure of the film. Hence, the Cu diffusion in SiCOH films can be reduced by O₂ plasma treatment. By FTIR and AFM analysis on the bonding configuration and microstructure, the reduce of Cu diffusion is related to the increase of Si-O cages and networks, which makes more open pores sealed at the surface of SiCOH films.     

A novel thermally-stable zirconium amidinate ALD precursor for ZrO2 thin films

ZrO₂ thin films were deposited by the atomic layer deposition process on Si substrates using tetrakis(N,N′-dimethylacetamidinate) zirconium (Zr-AMD) as a Zr precursor and H₂O as an oxidizing agent. Tetrakis (ethylmethylamino) zirconium (TEMA-Zr) was also evaluated for a comparative study. Physical properties of ALD-derived ZrO₂ thin films were studied using ellipsometry, grazing incidence XRD (GI-XRD), high resolution TEM (HRTEM), and atomic force microscopy (AFM). The ZrO₂ deposited using Zr-AMD showed a better thermal stability at high substrate temperature (>300 °C) compared to that using TEMA-Zr. GI-XRD analysis reveals that after 700 °C anneal both ZrO₂ films enter tetragonal phase. The electrical properties of N₂-annealed ZrO₂ film using Zr-AMD exhibit an EOT of 1.2 nm with leakage current density as low as 2 × 10⁻³ A/cm² (@V_fb−1 V). The new Zr amidinate is a promising ALD precursor for high-k dielectric applications.     

Charge trapping and interface characteristics in normally-off Al2O3/GaN-MOSFETs

Normally-off GaN-MOSFETs with Al₂O₃ gate dielectric have been fabricated and characterized. The Al₂O₃ layer is deposited by ALD and annealed under various temperatures. The saturation drain current of 330 mA/mm and the maximum transconductance of 32 mS/mm in the saturation region are not significantly modified after annealing. The subthreshold slope and the low-field mobility value are improved from 642 to 347 mV/dec and from 50 to 55 cm² V⁻¹ s⁻¹, respectively. The I_D-V_G curve shows hysteresis due to oxide trapped charge in the Al₂O₃ before annealing. The amount of hysteresis reduces with the increase of annealing temperature up to 750 °C. The Al₂O₃ layer starts to crystallize at a temperature of 850 °C and its insulating property deteriorates.     

The profile of temperature and voltage dependent series resistance and the interface states in (Ni/Au)/Al0.3Ga0.7N/AlN/GaN heterostructures

The temperature dependence of capacitance-voltage (C-V) and the conductance-voltage (G/w-V) characteristics of (Ni/Au)/Al_0.3Ga_0.7N/AlN/GaN heterostructures were investigated by considering the effect of series resistance (R_s) and interface states N_ss in a wide temperature range (79-395 K). Our experimental results show that both R_s and N_ss were found to be strongly functional with temperature and bias voltage. Therefore, they affect the (C-V) and (G/w-V) characteristics. The values of capacitance give two peaks at high temperatures, and a crossing at a certain bias voltage point (∼3.5 V). The first capacitance peaks are located in the forward bias region (∼0.1 V) at a low temperature. However, from 295 K the second capacitance peaks appear and then shift towards the reverse bias region that is located at ∼−4.5 V with increasing temperature. Such behavior, as demonstrated by these anomalous peaks, can be attributed to the thermal restructuring and reordering of the interface states. The capacitance (C_m) and conductance (G/w-V) values that were measured under both reverse and forward bias were corrected for the effect of series resistance in order to obtain the real diode capacitance and conductance. The density of N_ss, depending on the temperature, was determined from the (C-V) and (G/w-V) data using the Hill-Coleman Method.     

Co gamma irradiation effects on electrical characteristics of Al/Y2O3/n-Si/Al capacitors

Al/Y₂O₃/n-Si/Al capacitors were irradiated by using a ⁶⁰Co gamma ray source and a maximum dose up to 8.4 kGy. The effect of an annealing treatment performed at 600 or 900 °C on the yttrium oxide (Y₂O₃) films was investigated by XRD and Raman spectroscopy. High-frequency capacitance-voltage (C-V) and conductance-voltage (G-V) measurements as well as quasi-static measurements of the MOS structures were analysed. The annealing improves the crystalline state of the Y₂O₃ thin film material and decreases the values of the flat-band voltage and of the interface trap level density indicating an improvement of the electrical properties of the interface thin film-substrate. But at this interface, the formation of an yttrium-silicate layer was also evidenced. After gamma irradiation, the values of the flat-band voltage and of the interface trap level density related to the Al/Y₂O₃/n-Si/Al structure increase and especially for the structure made with the materials annealed at 900 °C for 1 h. In that case, the structure is very sensitive to a gamma irradiation dose up to 8.4 kGy.     

Frequency and voltage effects on the dielectric properties and electrical conductivity of Al-TiW-Pd2Si/n-Si structures

Different from conventional metal-Si compounds-n-Si structures, the thin film of TiW alloy was deposited on Pd₂Si-n-Si to form a diffusion barrier between aluminum (Al) and Pd₂Si-n-Si. Dielectric properties and electrical conductivity of TiW-Pd₂Si/n-Si structures in the frequency range of 5 kHz-10 MHz and voltage range of (−4 V) to (10 V) have been investigated in detail by using experimental C-V and G-V measurements. Experimental results indicate that the values of ε′ show a steep decrease with increasing frequency for each voltage. On the other hand, the values of ε″ show a peak, and its intensity increases with decreasing voltage and shifts towards the lower frequency side. The ac electrical conductivity (σ_ac) and the real part of electric modulus (M′) increase with increasing frequency. Also, the imaginary part of electric modulus (M″) shows a peak and the peak position shifts to higher frequency with increasing applied voltage. It can be concluded that the interfacial polarization can be more easily occurred at low frequencies, and the majority of interface states at metal semiconductor interface, consequently contributes to deviation of dielectric properties of TiW-Pd₂Si/n-Si structures.     

Influence of oxidation temperature on the microstructure and electrical properties of Ta2O5 on Si

The effect of the oxidation temperature (673-873 K) on the microstructural and electrical properties of thermal Ta₂O₅ thin films on Si has been studied. Auger electron spectroscopy and X-ray photoelectron spectroscopy results revealed that the films are non-stoichiometric in the depth; an interfacial transition layer between tantalum oxide and Si substrate, containing presumably SiO₂ was detected. It has been found by X-ray diffraction that the amorphous state of Ta₂O₅ depends on both the oxidation temperature and the thickness of the films—the combination of high oxidation temperature (>823 K) and thickness smaller than 50 nm is critical for the appearance of a crystal phase. The Ta₂O₅ layers crystallize to the monoclinic phase and the temperature of the phase transition is between 773 and 823 K for the thinner layers (<50 nm) and very close to 873 K for the thicker ones. The electrical characterization (current/voltage; capacitance/voltage) reveals that the optimal oxidation temperature for achieving the highest dielectric constant (∼32) and the lowest leakage current (10⁻⁸ A/cm² at 1 MV/cm applied field) is 873 K. The results imply that the poor oxidation related defects are rather the dominant factor in the leakage current than the crystallization effects.     

Materials and interfaces issues in pentacene/PTCDI-C8 ambipolar organic field-effect transistors with solution-based gelatin dielectric

Gelatin is a natural protein, which works well as the gate dielectric for pentacene/N,N-dioctyl-3,4,9,10-perylene tetracarboxylic diimide (PTCDI-C₈) ambipolar organic field-effect transistors (OFETs) in air ambient and in vacuum. An aqueous solution process was used to form the gelatin gate dielectric film on poly(ethylene terephthalate) (PET) by spin-coating and subsequent casting. Pentacene morphology and interface roughness are two major factors affecting the electron and hole field-effect mobility (μ_FE) values of pentacene/PTCDI-C₈ ambipolar OFETs in vacuum and in air ambient. In contrast, water absorption in gelatin has higher contribution to the electron and hole μ_FE values in air ambient. The ambipolar performance of pentacene/PTCDI-C₈ ambipolar OFETs depends on their layer sequence. For example, when PTCDI-C₈ is deposited onto pentacene, i.e. in the structure of PTCDI-C₈/pentacene, unbalanced ambipolar characteristics appear. In contrast, better ambipolar performance occurs in the structure of pentacene/PTCDI-C₈. The optimum ambipolar characteristics with electron μ_FE of 0.85 cm² V⁻¹ s⁻¹ and hole μ_FE of 0.95 cm² V⁻¹ s⁻¹ occurs at the condition of pentacene (40 nm)/PTCDI-C₈ (40 nm). Surprisingly, water absorption plays a crucial role in ambipolar performance. The device performance changes tremendously in pentacene/PTCDI-C₈ ambipolar OFETs due to the removal of water out of gelatin in vacuum. The optimum ambipolar characteristics with electron μ_FE of 0.008 cm² V⁻¹ s⁻¹ and hole μ_FE of 0.007 cm² V⁻¹ s⁻¹ occurs at the condition of pentacene (65 nm)/PTCDI-C₈ (40 nm). The roles of layer sequence, relative layer thickness, and water absorption are proposed to explain the ambipolar performance.     

Interfacial microstructure and electrical properties of HfAlOx thin films on compressively strained Si83Ge17 grown by RF magnetron sputtering

Interfacial microstructure and electrical properties of HfAlO_x films deposited by RF magnetron sputtering on compressively strained Si₈₃Ge₁₇/Si substrates were investigated. HfSiO_x-dominated amorphous interfacial layer (IL) embedded with crystalline HfSi_x nano-particles were revealed by high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy depth profile study. About 280 mV-wide clockwise capacitance-voltage(C-V) hysteresis for the HfAlO_x film deposited in Ar + N₂ mixed ambient was observed. Oxygen vacancies and interfacial defects in the HfSiO_x IL, as well as trapped charges in the boundaries between the HfSi_x nano-particles and surrounded amorphous HfSiO_x may be responsible for the large C-V hysteresis.     

Electrical properties of metal-ferroelectric-insulator-semiconductor structure using BaxSr1−xTiO3 for ferroelectric-gate field effect transistor

Perovskite ferroelectric Ba_xSr_1−xTiO₃ (x = 0.5, 0.6, 0.7 and 0.8) thin films have been fabricated as metal-ferroelectric-insulator-semiconductor (MFIS) configurations using a sol-gel technique. The C-V characteristics for different Ba-Sr ratios and different film thicknesses have been measured in order to investigate the ferroelectric memory window effect. The results show that the memory window width increases with the increase both of Ba content and film thickness. This behavior is attributed to the grain size and dipole dynamics effect. It is found also that the memory window increases as the applied voltage increases. In addition, the leakage current density for the films is measured and it is found to be of the order of 10⁻⁸ A/cm² for all tested samples, indicating that the films have good insulating characteristics.     

ALD of LaHfOx nano-laminates for high-κ gate dielectric applications

Electrical properties and thermal stability of LaHfO_x nano-laminate films deposited on Si substrates by atomic layer deposition (ALD) have been investigated for future high-κ gate dielectric applications. A novel La precursor, tris(N,N′-diisopropylformamidinato) lanthanum [La(ⁱPrfAMD)₃], was employed in conjunction with conventional tetrakis-(ethylmethyl)amido Hf (TEMA Hf) and water (H₂O). The capacitance-voltage curves of the metal oxide semiconductor capacitors (MOSCAPs) showed negligible hysteresis and frequency dispersion, indicating minimal deterioration of the interface and bulk properties. A systematic shift in the flat-band voltage (V_fb) was observed with respect to the change in structure of nano-laminate stacks as well as La₂O₃ to HfO₂ content in the films. The EOTs obtained were in the range of ∼1.23-1.5 nm with leakage current densities of ∼1.3 × 10⁻⁸ A/cm² to 1.3 × 10⁻⁵ A/cm² at V_fb − 1 V. In addition, the films with a higher content of La₂O₃ remained amorphous up to 950 °C indicating very good thermal stability, whereas the HfO₂ rich films crystallized at lower temperatures.     

A flip-chip packaged 80-nm In0.7Ga0.3As MHEMT for millimeter-wave low-noise applications

In this paper, we present a flip-chip 80-nm In_0.7Ga_0.3As MHEMT device on an alumina (Al₂O₃) substrate with very little decay on device RF performance up to 60 GHz. After package, the device exhibited high I_DS = 435 mA/mm at V_DS = 1.5 V, high g_m = 930 mS/mm at V_DS = 1.3 V, the measured gain was 7.5 dB and the minimum noise figure (NF_min) was 2.5 dB at 60 GHz. As compared to the bare chip, the packaged device exhibited very small degradation in performance. The result shows that with proper design of the matching circuits and packaging materials, the flip-chip technology can be used for discrete low noise FET package up to millimeter-wave range.     

Characteristics of metal-ferroelectric-insulator-semiconductor structure using Sr0.8Bi2.2Ta2O9 and Sr0.8Bi2.2Ta2O9-BaZrO3 for ferroelectric gates

Characteristics of BaZrO₃ (BZO) modified Sr_0.8Bi_2.2Ta₂O₉ (SBT) thin films fabricated by sol-gel method on HfO₂ coated Si substrates have been investigated in a metal-ferroelectric-insulator-semiconductor (MFIS) structure for potential use in a ferroelectric field effect transistor (FeFET) type memory. MFIS structures consisting of pure SBT and doped with 5 and 7 mol% BZO exhibited memory windows of 0.81, 0.82 and 0.95 V with gate voltage sweeps between −5 and +5 V, respectively. Leakage current density levels of 10⁻⁸ A/cm² for BZO doped SBT gate materials were observed and attributed to the metallic Bi on the surface as well as intrinsic defects and a porous film microstructure. The higher than expected leakage current is attributed to electron trapping/de-trapping, which reduces the data retention time and memory window. Further process improvements are expected to enhance the electronic properties of doped SBT for FeFET.