ZnO/SiC/Si异质结构的特性

用MOCVD方法在p型单晶Si（100）基片上外延SiC层,再用直流溅射在SiC层上生长ZnO薄膜,制备出ZnO／SiC／Si异质结构,用XRD和AFM分析了ZnO／SiC／Si和ZnO／Si异质结构中表层ZnO的结构和形貌的差别,研究了这种异质结构的特性．结果表明,在Si（100）基片上外延生长出的是高取向、高结晶质量的SiC（100）层．这个SiC层缓冲层使在Si基片上外延生长出了高质量ZnO薄膜,因为ZnO与SiC的晶格失配比ZnO与Si的晶格失配更低．     

The role of the Zn buffer layers in the structural and photoluminescence properties of ZnO films on Zn buffer layers deposited by RF magnetron sputtering

Highly c-axis oriented ZnO thin films were grown on Si (100) substrates with Zn buffer layers. Effects of the Zn buffer layer thickness on the structural and optical qualities of ZnO thin films were investigated for the ZnO films with the buffer layers 90, 110, and 130 nm thick using X-ray diffraction (XRD), photoluminescence (PL) and atomic force microscopy (AFM) analysis techniques. It was confirmed that the quality of a ZnO thin film deposited by RF magnetron sputtering was substantially improved by using a Zn buffer layer. The highest ZnO film quality was obtained with a Zn buffer layer 110 nm thick. The surface roughness of the ZnO thin film increases as the Zn buffer layer thickness increases.     

Effects of growth atmosphere and homo-buffer layer on properties of ZnO films prepared on Si(1 1 1) by PLD

ZnO films were synthesized on Si(1 1 1) substrates by pulsed laser deposition (PLD) under four different growth conditions. The structural and optical properties of the samples were characterized by reflection high-energy electron diffraction (RHEED), X-ray diffraction (XRD), and photoluminescence (PL) measurement. It is found that when ZnO film is directly prepared on Si, oxygen atmosphere can significantly enhance the near-band-edge (NBE) emission and decrease the deep-level (DL) emission, but cause a polycrystalline film. By introducing a homo-buffer layer fabricated at 500 °C in vacuum, epitaxial ZnO film with three-dimensional (3D) growth mode is achieved instead of the polycrystalline film. In particular, the epitaxial film with the buffer layer shows more intensive NBE emission and narrower full-width at half maximum (FWHM) of 98 meV than the film without the buffer layer. The experimental results suggest that both oxygen atmosphere and buffer layer are quite efficient during PLD to grow high-quality ZnO/Si heteroepitaxial films suitable for applications in optoelectronic devices.     

The structure and photoluminescence properties of ZnO/SiC multilayer film on Si substrate

ZnO/SiC multilayer film has been fabricated on a Si (111) substrate with a silicon carbide (SiC) buffer layer using the RF (radio frequency)-magnetron technique with targets of a ceramic polycrystalline zinc oxide (ZnO) and a composite target of pure C plate with attached Si chips on the surface. The as-deposited films were annealed at a temperature range of 600–1000°C under nitrogen atmosphere. The structure and photoluminescence (PL) properties of the samples were measured using X-ray diffractometry (XRD), Fourier transform infrared (FTIR) spectroscopy and PL spectrophotometry. By increasing the annealing temperature to 800°C, it is found that all the ZnO peaks have the strongest intensities, and the crystallinity of ZnO is more consistent on the SiC buffer layer. Further increase of the annealing temperature allows the ZnO and SiC layers to penetrate one another, which makes the interface between ZnO and SiC layer become more and more complicated, thus reduces the crystallinities of ZnO and SiC. The PL properties of a ZnO/SiC multilayer are investigated in detail. It is discovered that the PL intensities of these bands reach their maximum after being annealed at 800°C. The PL peaks shift with an increase in the annealing temperature, which is due to the ZnO and SiC layers penetrating reciprocally. This makes the interface more impacted and complicated, which induces band structure deformation resulting from lattice deformation.     

Effect of a ZnO buffer layer on the characteristics of MgZnO thin films grown on Si (100) substrates by radio-frequency magnetron sputtering

This is a report on the effect of a ZnO buffer layer on the microstructures and optical properties of MgZnO thin films grown on Si (100) substrates by radio frequency magnetron sputtering. For the sample without the ZnO buffer layer, the microstructural analyses carried out by X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed the formation of Mg₂Si in the interface between the Si substrate and the MgZnO thin film. Mg₂Si induced the random oriented polycrystalline MgZnO thin film. For the sample with the ZnO buffer layer, a few Mg₂Si were observed. An epitaxial relationship between the Si substrate and the MgZnO thin film was formed. In both samples, the photoluminescence (PL) investigation showed a small blue shift of the emission peak, which was owing to the incorporation of Mg atoms in ZnO by co-sputtering the MgO and ZnO targets. In addition, the sample with the ZnO buffer layer showed the enhanced PL intensity, when compared with the sample without the buffer layer.     

Improved microstructural properties of a ZnO thin film using a buffer layer in-situ annealed in argon ambient

ZnO films with improved crystallinity were grown on a Si (111) substrate by a two-step growth process using low-temperature ZnO buffer layers. The effect of the ambient gas during the temperature elevation and the in-situ thermal annealing after the growth of the low-temperature buffer layers on the optical and structural properties of the films was investigated by X-ray diffraction (XRD), photoluminescence, and transmission electron microscopy. The use of argon as the ambient gas during the thermal treatment of the buffer layer leads to the enhancement of the (0002) diffraction peak intensity at 2θ ∼ 34.4° and the reduction of the full width at half maximum value in the XRD rocking curve, which means that well-defined and c-axis oriented ZnO film was obtained. The relationship between the thickness of the SiO₂ layer between the ZnO buffer layers and Si substrates and the structural and optical properties of the ZnO films is discussed.     

Growth of GaN on SiC/Si substrates using AlN buffer layer by hot-mesh CVD

GaN films were grown on SiC/Si (111) substrates by hot-mesh chemical vapor deposition (CVD) using ammonia (NH₃) and trimetylgallium (TMG) under low V/III source gas ratio (NH₃/TMG = 80). The SiC layer was grown by a carbonization process on the Si substrates using propane (C₃H₈). The AlN layer was deposited as a buffer layer using NH₃ and trimetylaluminum (TMA). GaN films were formed and grown by the reaction between NH_x radicals, generated on a tungsten hot mesh, and the TMG molecules. The GaN films with the AlN buffer layer showed better crystallinity and stronger near-band-edge emission compared to those without the AlN layer.     

Effect of film thickness, type of buffer layer, and substrate temperature on the morphology of dicyanovinyl-substituted sexithiophene films

The influence of film thickness, type of buffer underlayer, and deposition substrate temperature on the crystal structure, microstructure, and morphology of the films of dicyanovinyl-substituted sexithiophene with four butyl-chains (DCV6T-Bu₄) is investigated by means of X-ray diffraction (XRD) and X-ray reflectivity methods. A neat Si wafer or a Si wafer covered by a 15 nm buffer underlayer of fullerene C₆₀ or 9,9-Bis[4-(N,N-bis-biphenyl-4-yl-amino)phenyl]-9H-fluorene (BPAPF) is used as a substrate. The crystalline nature and ordered molecular arrangement of the films are recorded down to 6 nm film thickness. By using substrates heated up to 90 °C during the film deposition, the size of the DCV6T-Bu₄ crystallites in direction perpendicular to the film surface increases up to value of the film thickness. With increasing deposition substrate temperature or film thickness, the DCV6T-Bu₄ film relaxes, resulting in reducing the interplane distances closer to the bulk values. For the films of the same thickness deposited at the same substrate temperature, the DCV6T-Bu₄ film relaxes for growth on Si to BPAPF to C₆₀. Thicker films grown at heated substrates are characterized by smaller density, higher roughness and crystallinity and better molecular ordering. A thin (up to about 6 nm-thick) intermediate layer with linear density-gradient is formed at the C₆₀/DCV6T-Bu₄ interface for the films with buffer C₆₀ layer. The XRD pattern of the DCV6T-Bu₄ powder is indexed using triclinic unit cell parameters.     

ZnO薄膜的晶体性能的分析

在硅基上制备出了c轴取向高度一致的ZnO薄膜 ,这将有可能成为新型GaN单晶薄膜的过渡层。对ZnO薄膜的晶体性能进行了分析 ,研究不同衬底和不同衬底温度对ZnO薄膜的结晶状况的影响 ,并着重用TEM研究了硅基ZnO薄膜的晶体性能。     

Dielectric properties of (Ba,Ca)(Zr,Ti)O3/CaRuO3 heterostructure thin films prepared by pulsed laser deposition

(Ba_0.90Ca_0.10)(Zr_0.25Ti_0.75)O₃ (BCZT) thin films were grown on Pt/Ti/SiO₂/Si substrates without and with a CaRuO₃ (CRO) buffer layer using pulsed laser deposition (PLD). The structure and surface morphology of the films have been characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). At room temperature and 1 MHz, the dependence of dielectric constant and tunability of the films with electric field were investigated; the dielectric constant and tunability are 725 and 47.0%, 877 and 50.4%, respectively, for the BCZT film on Pt/Ti/SiO₂/Si substrates without and with the CRO buffer layer at 400 kV/cm. The tunability of the BCZT/CRO heterostructure thin films on Pt/Ti/SiO₂/Si substrates was higher than that of the BCZT thin films on Pt/Ti/SiO₂/Si substrates. The high constant likely results from the oxide electrode (CRO).     

Effect of homo-buffer layers on the optical properties of ZnO thin films grown by pulsed laser deposition on Si (100)

The influence of homo-buffer layers deposited at high-temperature (HT) or low-temperature (LT) and post-annealing process on the structure and photoluminescence properties of ZnO films grown by pulsed laser deposition on Si (100) was studied by X-ray diffraction (XRD), atomic force microscope (AFM) and photoluminescence spectrum (PL). It is found that the optical property of the films can be improved greatly because the stress between the films and the substrates could be reduced by using buffer layers. By using LT buffer layer, high-quality ZnO films with only one strong ultraviolet emission (UV) can be obtained, but the post-annealing process in air will make the optical property of the film deteriorate.     

Effects of substrate parameters on structure and optical properties of ZnO thin films fabricated by pulsed laser deposition

Highly oriented zinc oxide thin films have been grown on quartz, Si (1 1 1) and sapphire substrates by pulsed laser deposition (PLD). The effect of temperature and substrate parameter on structural and optical properties of ZnO thin films has been characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmission spectra and PL spectra. The experimental results show that the best crystalline thin films grown on different substrate with hexagonal wurtzite structure were achieved at growth temperature 400–500 °C. The growth temperature of ZnO thin film deposited on Si (1 1 1) substrate is lower than that of sapphire and quartz. The band gaps are increasing from 3.2 to 3.31 eV for ZnO thin film fabricated on quartz substrate at growth temperature from 100 to 600 °C. The crystalline quality and UV emission of ZnO thin film grown on sapphire substrate are significantly higher than those of other ZnO thin films grown on different substrates.     

The growth of GaN films by alternate source gas supply hot-mesh CVD method

Gallium nitride (GaN) films and Aluminium nitride (AlN) layers were deposited on SiC/Si (111) substrates by an alternating source gas supply or an intermittent supply of a source gas such as ammonia (NH₃), trimethylgallium (TMG) or trimethylaluminum (TMA) in a hot-mesh chemical vapor deposition (CVD) apparatus. The AlN layer was deposited as a buffer layer using NH₃ and TMA on a SiC layer grown by carbonization on Si substrates using propane (C₃H₈). GaN films were grown on an AlN layer by a reaction between NH_x radicals generated on a ruthenium (Ru) coated tungsten (W)-mesh and TMG molecules. An alternating source gas supply or an intermittent supply of one of the source gases during the film growth are expected to be effective for the suppression of gas phase reactions and for the enhancement of precursor migration on the substrate surface. By the intermittent supply of alkylmetal gas only during the growth of the AlN layer, the defect generation in the GaN films was reduced. GaN film growth by intermittent supply on an AlN buffer layer, however, did not lead to the improvement of the film quality.     

High quality ZnO films deposited by radio-frequency magnetron sputtering using layer by layer growth method

Three-layered ZnO films were deposited on Si substrates by radio-frequency magnetron sputtering using layer by layer growth method. The Raman scattering confocal analysis confirms that ZnO film quality is improving at increasing the number of ZnO layers at film deposition.Applied method of deposition was used to realize homoepitaxial growth of ZnO films on c-Al₂O₃, Si, SiN_x/Si, glass and ITO/glass substrates. In order to improve the film quality we increased the number of deposition stages up to 5. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to testify the quality of grown five-layered ZnO films. XRD results showed that all five-layered ZnO films have (002) texture. The second order diffraction peak (004) on XRD spectra additionally testifies to the high quality of all five-layered ZnO films. SEM results demonstrated that no defects such as cracks and dislocations caused by interruption of deposition ZnO films were observed. Transmittance measurement results showed that ZnO films deposited on transparent substrates have abrupt absorption edge and high optical transmission in the visible region of the spectrum.     

Stable p-type conductivity and enhanced photoconductivity from nitrogen-doped annealed ZnO thin film

We report on the growth of p-type ZnO thin films with improved stability on various substrates and study the photoconductive property of the p-type ZnO films. The nitrogen doped ZnO (N:ZnO) thin films were grown on Si, quartz and alumina substrates by radio frequency magnetron sputtering followed by thermal annealing. Structural studies show that the N:ZnO films possess high crystallinity with c-axis orientation. The as-grown films possess higher lattice constants compared to the undoped films. Besides the high crystallinity, the Raman spectra show clear evidence of nitrogen incorporation in the doped ZnO lattice. A strong UV photoluminescence emission at ~ 380 nm is observed from all the N:ZnO thin films. Prior to post-deposition annealing, p-type conductivity was found to be unstable at room temperature. Post-growth annealing of N:ZnO film on Si substrate shows a relatively stable p-type ZnO with room temperature resistivity of 0.2 Ω cm, Hall mobility of 58 cm²/V s and hole concentration of 1.95 × 10¹⁷ cm^− 3. A homo-junction p-n diode fabricated on the annealed p-type ZnO layer showed rectification behavior in the current-voltage characteristics demonstrating the p-type conduction of the doped layer. Doped ZnO films (annealed) show more than two orders of magnitude enhancement in the photoconductivity as compared to that of the undoped film. The transient photoconductivity measurement with UV light illumination on the doped ZnO film shows a slow photoresponse with bi-exponential growth and bi-exponential decay behaviors. Mechanism of improved photoconductivity and slow photoresponse is discussed based on high mobility of carriers and photodesorption of oxygen molecules in the N:ZnO film, respectively.     

Fabrication and characterization of polyaniline-znO hybrid nanocomposite thin films

Polyaniline (PANI)-ZnO nanocomposite thin film has been successfully fabricated on glass substrates by using vacuum deposition technique. The as-grown PANI-ZnO nanocomposite thin films have been characterized using X-ray diffraction, Scanning Electron Microscopy, Atomic Force Microscopy, UV-visible spectrophotometer and Fourier Transform Infrared (FTIR) spectroscopy, respectively. X-ray diffraction of as-grown film shows the reflection of ZnO nanoparticles along with a broad peak of PANI. The surface morphology of nanocomposite films has been investigated using scanning electron microscopy and atomic force microscopy. The hypsochromic shift of the UV absorption band corresponding to pi-pi* transition in polymeric chain of PANI and a band at 504 cm(-1) due to ZnO nanoparticles has been observed in the FTIR spectra. The hydrogen bonding between the imine group of PANI and ZnO nanoparticle has been confirmed from the presence of the absorbance band at 1151 cm(-1) in the FTIR spectra of the nanocomposite thin films.     

Si(111)衬底上多层石墨烯薄膜的外延生长

利用固源分子束外延(SSMBE)技术, 在Si(111)衬底上沉积碳原子外延生长石墨烯薄膜, 通过反射式高能电子衍射(RHEED)、红外吸收谱(FTIR)、拉曼光谱(RAMAN)和X射线吸收精细结构谱(NEXAFS)等手段对不同衬底温度(400、600、700、800℃)生长的薄膜进行结构表征. RAMAN和NEXAFS结果表明: 在800℃下制备的薄膜具有石墨烯的特征, 而 400、600和700℃生长的样品为非晶或多晶碳薄膜. RHEED和FTIR结果表明, 沉积温度在600℃以下时C原子和衬底Si原子没有成键, 而衬底温度提升到700℃以上, 沉积的C原子会先和衬底Si原子反应形成SiC缓冲层, 且在800℃沉积时缓冲层质量较好. 因此在Si衬底上制备石墨烯薄膜需要较高的衬底温度和高质量的SiC缓冲层.     

SiCOI structure fabricated by catalytic chemical vapor deposition

Epitaxial growth of SiC on SOI substrates using a hot-mesh chemical vapor deposition (CVD) technique was investigated. This technique utilizes a catalytic reaction involving hot tungsten wires arranged in a mesh structure. Using this hot-mesh CVD method, SiC epitaxial growth on SOI substrates with a thin top Si layer was realized without formation of voids, which form readily in the thin Si top layer at temperatures above 800 °C. The SiC film grown on an SOI structure exhibited a large gage factor (GF) of − 27, which is approximately the same as that (GF = − 31.8) of a SiC epitaxial film on Si(100) grown at 1360 °C using atmospheric pressure CVD.     

Properties of LiNbO3 based heterostructures grown by pulsed-laser deposition for optical waveguiding application

Epitaxial LiNbO₃ (LN) thin films have been grown onto (00.1) Al₂O₃ substrates and onto sapphire covered with a conductive ZnO buffer layer. For the two systems, the LN thin films are well crystallised and highly (00.1) oriented. Epitaxial relationships between the different layers are evidenced both on the LN/sapphire film and the LN/ZnO/sapphire heterostructure. The optical waveguiding propagation losses of the LN/sapphire films are very low (1 ± 0.5 dB/cm) while the LN/ZnO/sapphire heterostructure does not exhibit satisfying waveguiding properties mainly due to the high conductivity (600 S m^− 1) of the ZnO buffer layer.     

High quality epitaxial ZnO films grown on solid-phase crystallized buffer layers

High quality epitaxial ZnO films on sapphire (110) plane have been fabricated on ZnO homo-buffer layers crystallized via solid-phase epitaxially (SPE). The SPE-ZnO films are fabricated by annealing of amorphous ZnON (a-ZnON) films deposited by RF magnetron sputtering. During annealing, the a-ZnON films are oxidized and converted to ZnO crystal. X-ray diffraction (XRD) analysis shows that the resultant films are epitaxially grown on the sapphire substrates. By using the SPE-ZnO films as homo-buffer layers, the ZnO films with high crystallinity, which are deposited by RF magnetron sputtering, are fabricated. The full width at half-maximum of XRD patterns for 2θ-ω and ω scan of (002) plane are 0.094° and 0.12°, respectively, being significantly small compared with 0.24° and 0.55° for the films without buffer layers. Thus utilizing SPE buffer layers is very promising to obtain epitaxial ZnO films with high crystallinity.