Fabrication of photocatalytic heat-mirror with TiO2/TiN/TiO2 stacked layers

The photocatalytic heat-mirror based on TiO₂/TiN/TiO₂ stacked layers is prepared by reactive magnetron sputtering on quartz substrates under substrate-heating condition. We find that the addition of a thin Ti interlayer between the TiN and the outer TiO₂ layers drastically improves the heat-insulating performance. This type of stacked layer also exhibits higher photocatalytic activity for decomposition of acetaldehyde gas, compared with a TiO₂ single layer. The optical property of the TiN in TiO₂/TiN/TiO₂ stacked layers is the key not only revealing excellent heat-insulating effect but also improving the photocatalytic performance of the outer TiO₂ layers in the stacked layers.     

Hydrothermal growth of rutile TiO2 nanorod films on titanium substrates

Rutile TiO₂ nanorod films have been successfully prepared on titanium substrate via a hydrothermal method using Tetra-n-butyl titanate as Ti source in the presence of concentrated hydrochloric acid. The effect of Ti substrate annealing treatment and adding of additional alkali metal chlorides in hydrothermal solution on the growth of TiO₂ nanorod films has been studied using scanning electron microscopy (SEM), Raman spectroscopy, X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and water contact angle measurement. The growth mechanism of the TiO₂ nanorods on Ti substrate has also been discussed. It has shown that the initial rutile film transformed from anatase promotes the nucleation and epitaxial growth of rutile TiO₂ nanorods. The superior wettabilities of the TiO₂ nanorods resulted from treatments of vacuum and ultraviolet show great potential for applications in orthopaedic, dental implants, and possible photocatalysis.     

Structural investigations on TiO2 and Fe-doped TiO2 nanoparticles synthesized by laser pyrolysis

Undoped and Fe-doped TiO₂ nanopowders with Fe/Ti (atomic ratio) precursor concentration ranging from 7% up to 25% have been prepared by the IR laser pyrolysis technique. A sensitized mixture of TiCl₄ and Fe (CO)₅ was used as titanium and iron precursor, respectively. Reference undoped titania samples with a major concentration of anatase phase (about 90%) were obtained by the same technique by using very high flows of the oxidizing agent (air). The effects of the iron-dopant concentration on the essential structural properties of the resultant powders such as the phase formation, the crystallinity, the average particle size and distributions were systematically investigated by X-ray diffraction, Raman spectroscopy and transmission electron microscopy. The decrease of the TiO₂-anatase crystalline phase, the simultaneous increase of the amorphous phase and the decrease in size of particle mean diameter appear as main effects induced by the Fe-dopant concentration.     

Enhanced photocatalytic activity of mesoporous TiO2 with MgO coating

To improve the photocatalytic activity of TiO₂ on decomposing anionic surfactants, MgO-coated mesoporous TiO₂ was fabricated by evaporation induced self-assembly (EISA) combined with impregnation method. MgO was uniformly dispersed on the surface of TiO₂, which played the role of stabilizing the ordered mesostructure of TiO₂ and improving the adsorption of anion surfactants, while inhibiting the crystallization of TiO₂. The powders coated with 5 wt.% MgO showed the highest photocatalytic activity for the decomposition of sodium dodecylbenzenesulfonate-6 (DBS).     

The role of the TiO2 nanotube array morphologies in the dye-sensitized solar cells

Arrays of TiO₂ nanotubes were fabricated by the anodization of Ti foils and then used in assembling dye-sensitized solar cells (DSSCs). The role of the morphologies of the TiO₂ nanotubes in the photovoltaic performances of the DSSCs was studied in terms of the surface topography and the tube length. The necessity of removing the nanoporous films from the surface of the nanotube arrays for good DSSC performance has been demonstrated. Also, it has been shown that appropriately increasing the tube length was an effective measure for enhancing both the short-circuit current density and the conversion efficiency of the DSSCs.     

Characterization of SiO2 and TiO2 films prepared using rf magnetron sputtering and their application to anti-reflection coating

Preparation of TiO₂ and SiO₂ films for optical applications was attempted using conventional rf magnetron sputtering in the sputtering ambient with various O₂/Ar+O₂ ratios and at substrate temperatures between room temperature and 400 °C. X-ray photoelectron spectroscopy (XPS) and optical spectroscopy investigations indicated that oxygen addition in the sputtering ambient was essential for growing TiO₂ films with stoichiometric compositions and good transmittance, while SiO₂ films had a stoichiometric composition of O/Si ratio=2.1-2.2 and were highly transparent in the visible wavelength region, independent of gas composition in the growing ambient. It was also identified from scanning electron microscope (SEM), atomic force microscope (AFM) and Fourier transform infrared spectroscopy (FTIR) measurements that the structural characteristics of both TiO₂ and SiO₂ films were significantly improved with O₂ addition in the sputtering ambient, showing smoother surface morphologies and higher resistances to water absorption when compared with films grown without O₂ addition. Heating of the substrate between 200 and 400 °C considerably increased the refractive index of TiO₂ layers, resulting in dense structures along with an improvement of crystallinity. For optical applications, AR coatings composed of 2-4 multi-layers on glass were designed and manufactured by stacking in turn the SiO₂ and TiO₂ films at room temperature and O₂/Ar+O₂=10%, and the performance of the produced coatings was compared with simulation results.     

SiO2/TiO2 multilayer films grown on cotton fibers surface at low temperature by a novel two-step process

A novel two-step process was developed to synthesize and deposit SiO₂/TiO₂ multilayer films onto the cotton fibers. In the first step, SiO₂ particles on cotton fiber surface were synthesized via tetraethoxysilane hydrolysis in the presence of cotton fibers, in order to protect the fibers against photo-catalytic decomposition by TiO₂ nanoparticles. In the second step, the growth of TiO₂ nanoparticles into the modified cotton fiber surface was carried out via a sol-gel method at the temperature as low as 100 °C. The as-obtained SiO₂/TiO₂ multilayer films coated on cotton fibers were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, atomic force microscopy and X-ray diffraction, respectively.     

Effect of TiO2-SiO2 sol-gel coating on the cpTi-porcelain bond strength

The effects of TiO₂-SiO₂ sol-gel coating with different firing temperatures (300 °C, 500 °C, and 750 °C) on the cpTi-porcelain bond strength were investigated in the present study. Prior to applying the low-fusing dental titanium porcelain, the phase, surface morphology, surface roughness and static water contact angle of the intermediate layer were evaluated. The cpTi-porcelain bond strength was measured using the three-point flexure test according to ISO 9693 standard. Statistical analyses were made using one-way ANOVA and Dunnett-t test. Significantly higher bond strength of TiO₂-SiO₂/750 °C (specimens coated with TiO₂-SiO₂ sol-gel coating and fired at 750 °C for 1 h) when compared to the control group was observed (p < 0.05). No rutile phase was found in all the tested specimens coated with TiO₂-SiO₂ sol-gel coating. The surface morphology of the intermediate layer was apparently different with different firing temperatures. It was found that the static water contact angle of TiO₂-SiO₂/750 °C significantly decreased (p < 0.05). However, no markedly different R_a of TiO₂-SiO₂/500 °C and TiO₂-SiO₂/750 °C in comparison to that of the control group was observed (p > 0.05). The results show that the TiO₂-SiO₂ sol-gel coating fired at 750 °C for 1 h can notably improve the cpTi-porcelain bond strength and may be suitable for clinical use.     

In-situ preparation of TiO2/SnO2 nanocrystalline sol for photocatalysis

A novel preparation method to synthesize TiO₂/SnO₂ nanocrystalline sol under mild conditions was presented. Ti(OC₄H₉)₄ used as a precursor was hydrolyzed in the rutile SnO₂ nanocrystalline sol, and in-situ formed TiO₂/SnO₂ nanocrystalline sol. The crystal structure, morphology and photocatalysis performance of samples were investigated. The results show that the additional rutile SnO₂ nano grains serve as heterogeneous crystal nucleus and exhibite the inducing effect on TiO₂ grains growth, thus leading to the changes in crystalline phase and particle morphology. In addition, the photoluminescence (PL) spectra analysis indicates that TiO₂/SnO₂ composite structure induces a better charge separation, and thus the photocatalytic activity of TiO₂/SnO₂ sol is increased significantly compared with TiO₂ sol.     

玄武岩纤维/TiO2复合材料的制备及表征

TiO_2纳米粉体应用于光催化领域存在光吸收仅局限于紫外光区域、难以回收等缺点,因此,纳米TiO_2固定化和可见光改性成为光催化领域的两个研究热点.本文采用绿色环保的水热法,将TiO_2负载于玄武岩纤维载体上,在较低的温度下制备出一种新型的玄武岩纤维/TiO_2复合材料.使用XRD分析了复合材料的物相结构,采用SEM观测了复合材料的形貌,并对水热法合成其机理进行了分析.结果表明:150℃水热条件下、反应10 h合成的玄武岩纤维/TiO_2复合材料中,颗粒状的TiO_2涂层均匀包覆于玄武岩纤维表面,并没有改变玄武岩纤维结构,形成了一种具有核壳结构的新型玄武岩纤维/TiO_2复合材料,经过TiO_2修饰的玄武岩纤维对可见光有很好吸收.因此,玄武岩纤维/TiO_2复合材料是一种具有潜在应用价值的可见光催化材料.     

Investigation on solar photocatalytic activity of TiO2 loaded composite: TiO2/Eggshell, TiO2/Clamshell and TiO2/CaCO3

The TiO₂/Eggshell, TiO₂/Clamshell and TiO₂/CaCO₃ loaded composites were prepared by sol-gel method and characterized by XRD and SEM. Their photocatalytic activities were measured through the degradation of Acid Red B under solar light irradiation. The influences of TiO₂ loaded content, heat-treated temperature and time on the photocatalytic activities were reviewed. The effects of irradiation time and dye initial concentration on the photocatalytic degradation were also investigated. The results showed that the photocatalytic activity can be greatly enhanced by appropriate TiO₂ loaded content.     

One-pot synthesis of intestine-like SnO2/TiO2 hollow nanostructures

In the present study the intestine-like binary SnO₂/TiO₂ hollow nanostructures are one-pot synthesized in aqueous phase at room temperature via a colloid seeded deposition process in which the intestine-like hollow SnO₂ spheres and Ti(SO₄)₂ are used as colloid seeds and Ti-source, respectively. The novel core (SnO₂ hollow sphere)-shell (TiO₂) nanostructures possess a large surface area of 122 m²/g (calcined at 350 °C) and a high exposure of TiO₂ surface. The structural change of TiO₂ shell at different temperatures was investigated by means of X-ray diffraction and Raman spectroscopy. It was observed that the rutile TiO₂ could form even at room temperature due to the presence of SnO₂ core and the unique core-shell interaction.     

Illumination-induced properties of highly ordered mesoporous TiO2 layers with controlled crystallinity

The evaporation-induced self-assembly method using a novel diblock (poly(ethylene-co-butylene)-b-poly(ethylene oxide)) copolymer (KLE) provides fully crystalline mesoporous layers of TiO₂ exhibiting high thermal stability up to 700 °C, high photocatalytic activity in the decomposition of methyl stearate and facile transformation into a substantially stable superhydrophilic state by 1 mW/cm² UV-illumination.     

Nanoporous TiO2 thin film based conductometric H2 sensor

Nanoporous titanium dioxide (TiO₂) based conductometric sensors have been fabricated and their sensitivity to hydrogen (H₂) gas has been investigated. A filtered cathodic vacuum arc (FCVA) system was used to deposit ultra-smooth Ti thin films on a transducer having patterned inter-digital gold electrodes (IDTs). Nanoporous TiO₂ films were obtained by anodization of the titanium (Ti) thin films using a neutral 0.5% (wt) NH₄F in ethylene glycol solution at 5 V for 1 h. After anodization, the films were annealed at 600 °C for 8 h to convert the remaining Ti into TiO₂. The scanning electron microscopy (SEM) images revealed that the average diameters of the nanopores are in the range of 20 to 25 nm. The sensor was exposed to different concentrations of H₂ in synthetic air at operating temperatures between 100 °C and 300 °C. The sensor responded with a highest sensitivity of 1.24 to 1% of H₂ gas at 225 °C.     

Photocatalytic degradation of RhB over MgFe2O4/TiO2 composite materials

MgFe₂O₄/TiO₂ (MFO/TiO₂) composite photocatalysts were successfully synthesized using a mixing-annealing method. The synthesized composites exhibited significantly higher photocatalytic activity than a naked semiconductor in the photodegradation of Rhodamine B. Under UV and visible light irradiation, the optimal percentages of doped MgFe₂O₄ (MFO) were 2 wt.% and 3 wt.%, respectively. The effects of calcination temperature on photocatalytic activity were also investigated. The origin of the high level of activity was discussed based on the results of X-ray diffraction, UV-vis diffuse reflection spectroscopy, scanning electron microscopy, transmission electron microscopy, and nitrogen physical adsorption. The enhanced activity of the catalysts was mainly attributed to the synergetic effect between the two semiconductors, the band potential of which matched suitably.     

A new method for surface modification of TiO2/Al2O3 nanocomposites with enhanced anti-friction properties

In this paper, the TiO₂/Al₂O₃ composite nanoparticles were prepared by a hydrothermal method and in situ modified with acrylic acid. It was found that the mean particle size of modified TiO₂/Al₂O₃ composite nanoparticles was about 80 nm with a uniform distribution by the particle size analysis. The modified TiO₂/Al₂O₃ composite nanoparticles can disperse in lubricating oil homogenously for several weeks. The dispersion stabilization of modified TiO₂/Al₂O₃ composite nanoparticles in lubricating oil was significantly improved in comparison with the as-prepared nanoparticles, which was due to the introduction of grafted polymers by surface modification. The formation of covalent bands was identified by Fourier transform infrared spectrum. Under an optimized concentration of 0.1 wt%, the averaged friction coefficient was reduced by 14.75%, when the modified TiO₂/Al₂O₃ composite nanoparticles were used as lubricating oil additivities.     

A Two-step anodization to grow high-aspect-ratio TiO2 nanotubes

High-aspect-ratio TiO₂ nanotubes with small diameter are favored in dye-sensitized solar cells for large dye loading provided by high surface areas. However, long TiO₂ nanotubes with small diameter are difficult to grow under usual anodizing conditions due to unavoidable chemical dissolution of the top portion of the as-fashioned tubes. In the present work, two kinds of double-layered TiO₂ nanotube arrays were prepared by changing voltage from high to low (i.e., from 30 V to 15 V) or from low to high (i.e., from 15 V to 30 V). It is found that the top layer can serve as a sacrificial layer to protect the continuous growth of the bottom layer from chemical dissolution. Accordingly, the two-step anodization from high voltage to low voltage is proposed to produce high-aspect-ratio TiO₂ nanotubes with small diameter underneath a sacrificial top layer.     

Phase transformation in semi-transparent TiO2 films irradiated with CO2 laser

Anatase (TiO₂) thin films were obtained by immersion of glass plates into a titanium sol-gel precursor followed by calcination at 450 °C for 3 h. The Raman results for the CO₂ laser irradiated TiO₂ films show that laser radiation is able to promote favorable changes of anatase phase in anatase/rutile mixtures. Nevertheless, the transformation process level depends on laser characteristics and scan speed of the radiation treatment.     

Enhanced photoelectrocatalytic activity in TiO2 nanotube arrays modified with TiO2 nanoparticles

The use of TiO₂ nanotube arrays fabricated by anode oxidation of titanium sheets as a photoelectrocatalyst is limited by low surface activity owing to passive crystallization post-treatment. We report here on a vacuum assisted filling route for modifying TiO₂ nanotube arrays using high-activity anatase TiO₂ nanoparticles as a filling. Photoelectrocatalytic degradation experiments show that a nearly 4-fold activity enhancement in photoelectrocatalysis is achieved and good photoelectrocatalytic stability is kept after the nanotube arrays are filled with the high-activity TiO₂ nanoparticles. The remarkable enhancement in photoelectrocatalysis is ascribed to the key modification of the TiO₂ nanotube arrays using the high-activity TiO₂ nanoparticles. Our findings provide an insight into designing excellent photoelectrocatalysts by filling TNAs with available high-activity TiO₂ nanoparticles.     

Anatase TiO2 films crystallized on SnO2:F substrates in an aqueous solution

Anatase TiO₂ films were fabricated on SnO₂:F substrates in an aqueous solution. The films were constructed of assemblies of nano-TiO₂. Surface of the films showed large roughness due to nano/micro-asperity of the assemblies. The thickness was increased to 260 nm, 360 nm, 600 nm and 760 nm with the deposition time of 2 h, 5 h, 25 h and 48 h, respectively. The films showed strong intensity of 004 X-ray diffraction possibly because the needles, i.e., nano-TiO₂, elongated along the c-axis. Low-temperature synthesis of crystalline anatase TiO₂ films has a great deal of potential in the development of electronic devices, optical devices, dye-sensitized solar cells, photocatalytic devices and biomolecule sensors.