Low temperature sintering and microwave dielectric properties of ZnTiNb2O8 ceramics with BaCu(B2O5) additions

The phases, microstructure and microwave dielectric properties of ZnTiNb₂O₈ ceramics with BaCu(B₂O₅) additions prepared by solid-state reaction method have been investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The pure ZnTiNb₂O₈ ceramic shows a high sintering temperature of about 1250 °C. However, it was found that the addition of BaCu(B₂O₅) lowered the sintering temperature of ZnTiNb₂O₈ ceramics from above 1250 °C to 950 °C due to the BCB liquid-phase. The results showed that the microwave dielectric properties were strongly dependent on densification, crystalline phases and grain size. Addition of 3 wt% BCB in ZnTiNb₂O₈ ceramics sintered at 950 °C afforded excellent dielectric properties of ?_r = 32.56, Q × f = 20,100 GHz (f = 5.128 GHz) and τ_f = −64.87 ppm/°C. These represent very promising candidates for LTCC dielectric materials.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Sintering and dielectric properties of 0.88Al2O3-0.12TiO2 microwave ceramics by glass addition

The microwave characteristics and the microstructures of 0.88Al₂O₃-0.12TiO₂ with various amounts of MgO-CaO-SiO₂-Al₂O₃ (MCAS) glass sintered at different temperatures have been investigated. The sintering temperature can be lowered to 1300 °C by the addition of MCAS glass. The densities, dielectric constants (ε_r) and quality values (Q×f) of the MCAS-added 0.88Al₂O₃-0.12TiO₂ ceramics decrease with the increase of MCAS glass content. The temperature coefficients of the resonant frequency (τ_f) are shifted to more negative values as the MCAS content or the sintering temperatures increase. The change of the crystalline phases of Al₂TiO₅ phase and rutile-TiO₂ phase has profound effects on the microwave dielectric properties of the MCAS-added Al₂O₃-TiO₂ ceramics. As sintered at 1250 °C, 0.88Al₂O₃-0.12TiO₂ ceramics with 2 wt.% MCAS glass addition exists a ε_r value of 8.63, a Q×f value of 9578 and a τ_f value of +5 ppm/°C.     

Low-temperature sintering of (Zn0.8 Mg0.2)2SiO4-TiO2 ceramics

Effect of Li₂O-B₂O₃-SiO₂ (LBS) glass on the sintering behavior and the microwave dielectric properties of (Zn_0.8 Mg_0.2)₂SiO₄-TiO₂ (ZMST) ceramics were investigated. The Li₂O-B₂O₃-SiO₂ glass lowered the sintering temperature of ZMST ceramics effectively from 1250 to 870 °C. The unknown second phase, which was formed in the ZMST ceramics increased with the addition of LBS glass. With increasing the LBS glass content, the bulk density, dielectric constant (ε_r) and the maximum Q × f value decreased, and the temperature coefficient of resonant frequency (τ_f) shifted to a negative value. (Zn_0.8 Mg_0.2)₂SiO₄-TiO₂ ceramics with 3 wt.% Li₂O-B₂O₃-SiO₂ glass sintered at 870 °C for 2 h shows excellent dielectric properties: ε_r = 8.48, Q × f = 11500 GHz, and τ_f = 0 ppm/°C.     

(5 − x)BaO-xMgO-2Nb2O5 ceramics prepared using a reaction-sintering process

(5 − x)BaO-xMgO-2Nb₂O₅ (x = 0.5 and 1; 5MBN and 10MBN) microwave ceramics prepared using a reaction-sintering process were investigated. Without any calcinations involved, the mixture of BaCO₃, MgO, and Nb₂O₅ was pressed and sintered directly. MBN ceramics were produced after 2-6 h of sintering at 1350-1500 °C. The formation of (BaMg)₅Nb₄O₁₅ was a major phase in producing 5MBN ceramics, and the formation of Ba(Mg_1/3Nb_2/3)O₃ was a major phase in producing 10MBN ceramics. As CuO (1 wt%) was added, the sintering temperature dropped by more than 150 °C. We produced 5MBN ceramics with these dielectric properties: ?_r = 36.69, Qf = 20,097 GHz, and τ_f = 61.1 ppm/°C, and 10MBN ceramics with these dielectric properties: ?_r = 39.2, Qf = 43,878 GHz, and τ_f = 37.6 ppm/°C. The reaction-sintering process is a simple and effective method for producing (5 − x)BaO-xMgO-2Nb₂O₅ ceramics for applications in microwave dielectric resonators.     

Characterization and dielectric behavior of CuO-doped ZnTa2O6 ceramics at microwave frequency

The effects of CuO addition on the microstructures and microwave dielectric properties of ZnTa₂O₆ ceramics were investigated. CuO was selected as a liquid-phase sintering aid to lower the sintering temperature of ZnTa₂O₆ ceramics. With CuO addition, the sintering temperature of ZnTa₂O₆ can be effectively reduced from 1350 to 1230 °C. The crystalline phase exhibited no phase difference and no second phase was detected at low addition levels (0.25-1 wt.%). The quality factors Q × f were strongly dependent upon the CuO concentration. A Q × f value of 65,500 GHz was obtained for specimen with 0.25 wt.% CuO addition at 1230 °C. For all levels of CuO concentration, the relative dielectric constants were not significantly different and ranged from 34.2 to 35.7. Tunable temperature coefficient of resonant frequency (τ_f) can be adjusted to zero by appropriately turning the CuO content.     

Improved high-Q microwave dielectric resonator using CuO-doped MgNb2O6 ceramics

The microwave dielectric properties and the microstructures of MgNb₂O₆ ceramics with CuO additions (1-4 wt.%) prepared with conventional solid-state route have been investigated. The sintered samples exhibit excellent microwave dielectric properties, which depend upon the liquid phase and the sintering temperature. It is found that MgNb₂O₆ ceramics can be sintered at 1140 °C due to the liquid phase effect of CuO addition. At 1170 °C, MgNb₂O₆ ceramics with 2 wt.% CuO addition possesses a dielectric constant (ε_r) of 19.9, a Q×f value of 110,000 (at 10 GHz) and a temperature coefficient of resonant frequency (τ_f) of −44 ppm/°C. The CuO-doped MgNb₂O₆ ceramics can find applications in microwave devices requiring low sintering temperature.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Low-temperature sintering and compatibility with silver electrode of Ba4MgTi11O27 microwave dielectric ceramic

Ba₄MgTi₁₁O₂₇ microwave dielectric ceramic was investigated using X-ray diffraction, scanning electron microscopy and dielectric measurement. The pure Ba₄MgTi₁₁O₂₇ ceramic shows a high sintering temperature (∼1275 °C) and good microwave dielectric properties as Q × f of 19,630 GHz, ?_r of 36.1, τ_f of 14.6 ppm/°C. It was found that the addition of BaCu(B₂O₅) (BCB) can effectively lower the sintering temperature from 1275 to 925 °C, and does not induce much degradation of the microwave dielectric properties. The BCB-doped Ba₄MgTi₁₁O₂₇ ceramics can be compatible with Ag electrode, which makes it a promising ceramic for LTCC technology application.     

Effect of B2O3-Bi2O3-SiO2-ZnO glass on the sintering and microwave dielectric properties of 0.83ZnAl2O4-0.17TiO2

The 0.83ZnAl₂O₄-0.17TiO₂ (ZAT) ceramics were synthesized by solid state ceramic route. The effect of 27B₂O₃-35Bi₂O₃-6SiO₂-32ZnO (BBSZ) glass on the microwave dielectric properties of ZAT was investigated. The crystal structure and the microstructure of the ceramic-glass composites were studied by X-ray diffraction and scanning electron microscopic techniques. The low frequency dielectric loss was measured at 1 MHz. The dielectric properties of the sintered samples were measured in the microwave frequency range by the resonance method. Addition of 0.2 wt% of BBSZ improved the dielectric properties with quality factor (Q_u × f) > 120,000 GHz, temperature coefficient of resonant frequency (τ_f) = −7.3 ppm/°C and dielectric constant (?_r) = 11.7. Addition of 10 wt% of BBSZ lowered the sintering temperature to about 950 °C with Q_u × f > 10,000 GHz, ?_r = 10 and τ_f = −23 ppm/°C. The reactivity of 10 wt% BBSZ added ZAT with silver was also studied. The results show that ZAT doped with suitable amount of BBSZ glass is a possible material for low-temperature co-fired ceramic (LTCC) application.     

Synthesis and microwave dielectric properties of CaO-MgO-SiO2 submicron powders doped with Li2O-Bi2O3 by sol-gel method

Using Ca(NO₃)₂·4H₂O, Mg(NO₃)₂·6H₂O, Si(OC₂H₅)₄, LiNO₃ and Bi(NO₃)₃·5H₂O as raw materials, CaO-MgO-SiO₂ submicron powders were prepared at low temperature by sol-gel method. The crystallization temperature was decreased enormously by the introduction of Li-Bi liquid phase sintering aids into Ca-Mg-Si sol, and the powders with average particle sizes of 80-100 nm and 200-400 nm were obtained at the calcining temperature of 750 °C and 800 °C, respectively. The sintering characteristic and dielectric properties of powders calcined at 750 °C with different content of powders calcined at 800 °C were studied. When the content of powders calcined at 800 °C was 10 wt%, the dielectric ceramic sintered at 890 °C had compact structure, and possessed excellent microwave dielectric properties: ?_r = 7.16, Q × f = 25630 GHz, τ_f = −69.26 ppm/°C.     

Influence of Bi2O3 and CuO addition on low-temperature sintering and dielectric properties of Ba0.6Sr0.4TiO3 ceramics

In this study, we tried to lower the sintering temperature of Ba_0.6Sr_0.4TiO₃ (BST) ceramics by several kinds of adding methods of Bi₂O₃, CuO and CuBi₂O₄ additives. The effects of different adding methods on the microstructures and the dielectric properties of BST ceramics have been studied. In the all additive systems, the single addition of CuBi₂O₄ was the most effective way for lowering the sintering temperature of BST. When CuBi₂O₄ of 0.6 mol% was mixed with starting BST powders and sintered at 1100 °C, the derived ceramics demonstrated dense microstructure with a low dielectric constant (? = 4240), low dielectric loss (tan δ = 0.0058), high tunability (Tun = 38.3%) and high Q value (Q = 251). It was noteworthy that the sintering temperature was significantly lowered by 350 °C compared with no-additive system, and the derived ceramics maintained the excellent microwave dielectric properties corresponding to pure BST.     

Preparation, structure and dielectric properties of Ba4LaMNb3O15 (M = Ti, Sn ) ceramics

Two new cation-deficient hexagonal perovskites Ba₄LaMNb₃O₁₅ (M = Ti, Sn) ceramics were prepared by high temperature solid-state reaction route. The phase and structure of the ceramics were characterized by X-ray diffraction, scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The Ba₄LaTiNb₃O₁₅ has high dielectric constant of 52, high quality factors (Q) 3500 (at 4.472 GHz), and temperature variation of resonant frequency (τ_f) +93 ppm °C⁻¹ at room temperature; Ba₄LaSnNb₃O₁₅ has dielectric constant of 39 with high Q value of 2510 (at 5.924 GHz), and τ_f −29 ppm °C⁻¹.     

Phase relations and microwave dielectric properties of vanadium modified Ba5Nb4O15 ceramics

Microwave dielectric ceramics of Ba₅Nb_4−xV_xO₁₅ (x = 0-1) were prepared by a solid-state reaction method. Vanadium substitution can markedly lower the sintering temperature of Ba₅Nb₄O₁₅ from 1450 to 1100 °C. The X-ray powder diffraction analysis reveals the multiphase nature of this system. A hexagonal-to-orthorhombic phase transition was also observed for the BaNb₂O₆ secondary phase. The microwave dielectric properties, such as τ_f, ε_r and Q × f value, decreased with increasing vanadium content for samples sintered at 1100 °C. There was an apparent increase in τ_f and Q × f value for samples (x ≥ 0.5) sintered at 1200 °C due to the hexagonal-to-orthorhombic phase transition of the BaNb₂O₆ phase. These results suggested that the microwave dielectric properties of multiphase ceramics strongly depended on the phase compositions and the phase transitions.     

Microwave dielectric properties of LaMgAl11O19

The suitable choice of a substrate material is one of the aims to be fulfilled in high speed microwave technology. LaMgAl₁₁O₁₉ oxide ceramic material, which belongs to the magnetoplumbite family, has been reported earlier as a potential candidate for such applications. This material has been prepared by conventional solid-state ceramic route. The structure has been studied by X-ray diffraction and characterized at microwave frequencies. The effect of dopant and glass addition on the microwave dielectric properties of this material has also been investigated. LaMgAl₁₁O₁₉ has relatively low dielectric constant (ε_r=14), low dielectric loss or high quality factor (Q_u×f>28,000 GHz at 7 GHz) and small temperature variation of resonant frequency (τ_f=−12 ppm/°C) at room temperature (300 K). These properties make LaMgAl₁₁O₁₉ as a good substrate material and as a dielectric resonator to be used in microwave devices operating at relatively high frequencies.     

Improved microwave dielectric properties of B2O3-doped Nd(Co1/2Ti1/2)O3 ceramics with near zero temperature coefficient of resonant frequency

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ ceramics prepared by conventional solid-state route have been studied. The prepared Nd(Co_1/2Ti_1/2)O₃ exhibited a mixture of Co and Ti showing 1:1 order in the B-site. It is found that low-level doping of B₂O₃ (up to 0.75 wt.%) can significantly improve the density and dielectric properties of Nd(Co_1/2Ti_1/2)O₃ ceramics. Nd(Co_1/2Ti_1/2)O₃ ceramics with additives could be sintered to a theoretical density higher than 98.5% at 1320 °C. Second phases were not observed at the level of 0.25-0.75 wt.% B₂O₃ addition. The temperature coefficient of resonant frequency (τ_f) was not significantly affected, while the dielectric constants (?_r) and the unloaded quality factors Q were effectively promoted by B₂O₃ addition. At 1320 °C/4 h, Nd(Co_1/2Ti_1/2)O₃ ceramics with 0.75 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 27.2, a Q × f value of 153,000 GHz (at 9 GHz) and a temperature coefficient of resonant frequency (τ_f) of 0 ppm/°C. The B₂O₃-doped Nd(Co_1/2Ti_1/2)O₃ ceramics can find applications in microwave devices requiring low sintering temperature.     

Low-temperature sintering of temperature-stable LaNbO4 microwave dielectric ceramics

We demonstrate the correlation between sintering behavior and microstructural observations in low-temperature sintered, LaNbO₄ microwave ceramics. Small CuO additions to LaNbO₄ significantly lowered the sintering temperature from 1250 to 950 °C. To elucidate the sintering mechanism, the internal microstructure of the sample manipulated by a focused ion beam (FIB) was investigated using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). LaNbO₄ with 3 wt% CuO sintered at 950 °C for 2 h possessed the following excellent microwave dielectric properties: a quality factor (Qxf) of 49,000 GHz, relative dielectric constant (?_r) of 19.5, and temperature coefficient of resonant frequency (τ_f) of 1 ppm/°C. The ferroelastic phase transformation was also investigated using in situ X-ray diffraction (XRD) to explain the variation of τ_f in low-temperature sintered LaNbO₄ as a function of CuO content.     

Correlation of crystal structure and microwave dielectric properties for Zn(Ti1−xSnx)Nb2O8 ceramics

The correlation of crystal structure and microwave dielectric properties for Zn(Ti_1−xSn_x)Nb₂O₈ ceramics were investigated. The Zn(Ti_1−xSn_x)Nb₂O₈ ceramics contained ZnTiNb₂O₈ and an unknown Columbite-type phase. The columbite structure phase with increasing degree of ordering led to decrease of dielectric constant, increase of Qf and τ_f. The ZnTiNb₂O₈ with decreasing cation valence led to increase of τ_f. The typical values were: ? = 30.88, Qf = 43,500 GHz, τ_f = −54.32 × 10⁻⁶/ °C.     

Dielectric properties of (1−x)(Mg0.95Co0.05)TiO3-xCaTiO3 ceramic system at microwave frequency

The microwave dielectric properties and the microstructures of the (1−x)MgTiO₃-xCaTiO₃ ceramic system were investigated. With partial replacement of Mg by Co, dielectric properties of the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature. At 1275°C, the 0.95(Mg_0.95Co_0.05)TiO₃-0.05CaTiO₃ ceramics possesses excellent microwave dielectric properties: a dielectric constant ε_r of 20.3, a Q×f value of 107 000 ( at 7 GHz) and a τ_f value of −22.8 ppm/°C. By appropriately adjusting the x value in the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramic system, zero τ_f value can be achieved. With x=0.07, a dielectric constant ε_γ of 21.6, a Q×f value of 92 000 (at 7 GHz) and a τ_f value of −1.8 ppm/°C was obtained for 0.93(Mg_0.95Co_0.05)TiO₃-0.07CaTiO₃ ceramics sintered at 1275°C for 4 h.     

Ba2Ti9O20-Ba1.85Sm4.1Ti9O24 layered dielectric resonators with adjustable effective dielectric constant

The layered dielectric resonator structures composed of Ba₂Ti₉O₂₀ (BTO) and Ba_1.85Sm_4.1Ti₉O₂₄ (BSTO) ceramic pellets were introduced to design new microwave dielectric materials with adjustable dielectric constant between 50 and 70. Good combination of microwave dielectric properties (?_r,eff = 50 ~ 70, Qf = 11,700-19,100 GHz and τ_f = − 4.3 to − 1.5 ppm/°C) was obtained by the present approach, and such combination could be optimized by adjusting the volume fraction of BSTO and stacking scheme. For practical applications, the BTO and BSTO layers could be bonded by low-loss adhesive, and the effects of the adhesive on the microwave dielectric properties were limited.