Sc2O3 Nanopowders via Hydroxyl Precipitation: Effects of Sulfate Ions on Powder Properties

Hydroxyl-type Sc₂O₃ precursors have been synthesized via precipitation at 80°C with hexamethylenetetramine as the precipitant. The effects of starting salts (scandium nitrate and sulfate) on powder properties are investigated. Characterizations of the powders are achieved by elemental analysis, X-ray diffractometry (XRD), differential thermal analysis/thermogravimetry (DTA/TG), high-resolution scanning electron microscopy (HRSEM), and Brunauer-Emmett-Teller (BET) analysis. Hard-aggregated precursors (γ-ScOOH·0.6H₂O) are formed with scandium nitrate, which convert to Sc₂O₃ at temperatures ≥400°C, yielding nanocrystalline oxides of low surface area. The use of sulfate leads to a loosely agglomerated basic sulfate powder having an approximate composition of Sc(OH)_2.6(SO₄)_0.2·H₂O. The powder transforms to Sc₂O₃ via dehydroxylization and desulfurization at temperatures up to 1000°C. Well-dispersed Sc₂O₃ nanopowders (∼64.3 nm) of high purity have been obtained by calcining the basic sulfate at 1000°C for 4 h. The effects of SO₄²⁻ on powder properties are discussed.     

High-Temperature Phase Relations in the Sc2O3-Ta2O5 System

The phase relations for the Sc₂O₃-Ta₂O₅ system in the composition range of 50-100 mol% Sc₂O₃ have been studied by using solid-state reactions at 1350°, 1500°, or 1700°C and by using thermal analyses up to the melting temperatures. The Sc_5.5Ta_1.5O₁₂ phase, defect-fluorite-type cubic phase (F-phase, space group Fm 3 m ), ScTaO₄, and Sc₂O₃ were found in the system. The Sc_5.5Ta_1.5O₁₂ phase formed in 78 mol% Sc₂O₃ at <1700°C and seemed to melt incongruently. The F-phase formed in ∼75 mol% Sc₂O₃ and decomposed to Sc_5.5Ta_1.5O₁₂ and ScTaO₄ at <1700°C. The F-phase melted congruently at 2344°± 2°C in 80 mol% Sc₂O₃. The eutectic point seemed to exist at ∼2300°C in 90 mol% Sc₂O₃. A phase diagram that includes the four above-described phases has been proposed, instead of the previous diagram in which those phases were not identified.     

Double Precursor Solution Coating Approach for Low-Temperature Sintering of [Pb(Mg1/3Nb2/3)O3]0.63[PbTiO3]0.37 Solids

Lead-based piezoelectric ceramics typically require sintering temperatures higher than 1000°C at which significant lead loss can occur. Here, we report a double precursor solution coating (PSC) method for fabricating low-temperature sinterable polycrystalline [Pb(Mg_1/3Nb_2/3)O₃]_0.63-[PbTiO₃]_0.37 (PMN–PT) ceramics. In this method, submicrometer crystalline PMN powder was first obtained by dispersing Mg(OH)₂-coated Nb₂O₅ particles in a lead acetate/ethylene glycol solution (first PSC), followed by calcination at 800°C. The crystalline PMN powder was subsequently suspended in a PT precursor solution containing lead acetate and titanium isopropoxide in ethylene glycol to form the PMN–PT precursor powder (second PSC) that could be sintered at a temperature as low as 900°C. The resultant d ₃₃ for samples sintered at 900°, 1000°, and 1100°C for 2 h were 600, 620, and 700 pm/V, respectively, comparable with the known value. We attributed the low sintering temperature to the reactive sintering nature of the present PMN–PT precursor powder. The reaction between the nanosize PT and the submicrometer-size PMN occurred roughly in the same temperature range as the densification, 850°–900°C, thereby significantly accelerating the sintering process. The present PSC technique is very general and should be readily applicable to other multicomponent systems.     

Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Sr3LaNb3O12: A New Low Loss and Temperature Stable A4B3O12-Type Microwave Dielectric Ceramic

The microwave dielectric properties of dense ceramics of a new A₄B₃O₁₂ type cation-deficient hexagonal perovskite Sr₃LaNb₃O₁₂ are reported. Single-phase powders can be obtained from the mixed-oxide route at 1320°C and dense ceramics (>96% of the theoretical X-ray density) with uniform microstructures (5–12 um) can be obtained by sintering in air at 1430°C. The ceramic exhibits a moderate dielectric constant ɛ_r∼36, a high quality factor Q × f ∼45 327 GHz, and a low temperature coefficient of resonant frequency τ _f of −9 ppm/°C.     

Synthesis and Processing Characteristics of Ba0.65Sr0.35TiO3 Powders from Catecholate Precursors

Powders of composition Ba_0.65Sr_0.35TiO₃ were prepared from catecholate precursor phases, BaTi(C₆H₄O₂)₃ and SrTi (C₆H₄O₂)₃. The physical and chemical properties of the base powders, and those doped with 0.2 wt% manganese, are reported in detail. The dimensions of the primary particles in the starting powders were of the order of 20–50 nm, but the occurrence of abnormal grain growth during sintering promoted grain sizes in the ceramic of up to ∼100 μm. In some microstructures, coarse grains coexisted with a ∼1-μm fraction to produce a characteristic bimodal grain size distribution. By contrast, under comparable sintering conditions, namely 1350° or 1400°C for 1 h, grain growth in Mn-doped samples was suppressed, leading to uniform microstructures with a grain size of only a few micrometers. The pellet densities were nevertheless similar, 97% of theoretical in both doped and undoped samples. No significant difference was observed in the dielectric permittivity of the two compositions: the peak relative permittivity occurred at ∼20°C, with a maximum value of ∼22 000.     

The System Sc2O3-WO3

Phase relations in the system Sc₂O₃-WO₃ were characterized. Two stable binary compounds were, found. The 1:3 compound, SC₂(WO₄)₃, melts congruently at 1640°±10°C and forms a simple eutectic with WO₃ at ∼90 mol% WO₃ and 1309°+10°C. The 3 : 1 compound, Sc₆WO₁₂, forms a simple eutectic with the 1:3 compound at -69 mol% WO₂, and 1580°+10°C. The melting temperature of SC₆WO₁₂ was >1600°C.     

Densification of Cr2O3-ZrO2 Ceramics by Sintering

Cr₂O₃ and ZrO₂ were mixed in various ratios and pressed to form compacts, which were then sintered in carbon powder. Compacts with >30 wt% Cr₂O₃ were sintered to densities >98% of true density at 1500°C. This method of sintering in carbon powder can be used to prepare very dense Cr₂O₃-ZrO₂ ceramics at a relatively low temperature, (∼1500°C) without additives.     

Fabrication and Photoluminescence Characteristics of Eu3+-Doped Lu2O3 Transparent Ceramics

A novel co-precipitation process was adopted for the preparation of highly sinterable europium-doped lutetia powders using ammonium hydroxide (NH₃·H₂O) and ammonium hydrogen carbonate (NH₄HCO₃) as the mixed precipitant. The resultant powders calcined at 1000°C for 2 h showed good dispersity and excellent sinterability. Highly transparent polycrystalline lutetia ceramics with a relative density of ∼99.9% were fabricated by pressureless sintering in flowing H₂ atmosphere at 1850°C for 6 h without any additives. The average grain sizes of the transparent material were estimated to be 50–60 μm. Optical in-line transmittance in the visible wavelength region for Lu₂O₃ ceramics (1 mm in thickness) reached 80%. The luminescence and decay behavior of the obtained transparent plate and the corresponding nanophosphors were also investigated.     

Mullite Crystallization from SiO2-Al2O3 Melts

SiO₂-Al₂O₃ melts containing 42 and 60 wt% A1₂O₃ were homogenized at 2090°C (∼10°) and crystallized by various heat treatment schedules in sealed molybdenum crucibles. Mullite containing ∼78 wt% A1₂O₃ precipitated from the 60 wt% A1₂O₃ melts at ∼1325°± 20°C, which is the boundary of a previously calculated liquid miscibility gap. When the homogenized melts were heat-treated within this gap, the A1₂O₃ in the mullite decreased with a corresponding increase in the Al₂O₃ content of the glass. A similar decrease of Al₂O₃ in mullite was observed when crystallized melts were reheated at 1725°± 10°C; the lowest A1₂O₃ content (∼73.5 wt%) was in melts that were reheated for 110 h. All melts indicated that the composition of the precipitating mullite was sensitive to the heat treatment of the melts.     

Preparation of Ca3Co4O9 and Improvement of its Thermoelectric Properties by Spark Plasma Sintering

The precursor powders of Ca₃Co₄O₉ were synthesized by a sol–gel method. The results of X-ray diffraction and thermogravimetric and differential thermal analyses patterns indicate that pure Ca₃Co₄O₉ powders could be obtained by calcining the precursor at 800°C for 2 h. High dense Ca₃Co₄O₉ ceramic samples (∼99% of theoretical density) were prepared by the spark plasma sintering (SPS) method. Compared with the conventional sintering (CS), the SPS samples exhibit much higher electrical conductivity and power factor which are respectively about 118 S/cm and 3.51 × 10⁻⁴ W·(m·K²)⁻¹. The SPS method is greatly effective for improving the thermoelectric properties of Ca₃Co₄O₉ oxide ceramics.     

Microwave Dielectric Properties of Low Firing Temperature Bi2W2O9 Ceramics

Phase stability, sinterability, and microwave dielectric properties of Bi₂W₂O₉ ceramics and their cofireability with Ag, Cu, and Au electrodes have been investigated. Single-phase Bi₂W₂O₉ powder was synthesized by solid-state reaction in air at 800°C for 3 days. X-ray powder diffraction data show Bi₂W₂O₉ to have an orthorhombic crystal structure described by the noncentrosymmetric space group Pna 2₁, with lattice parameters a =5.4401(8), b =5.4191(8), c =23.713(4) Å. Ceramics fired at temperatures up to 865°C remain single-phase but above this temperature ferroelectric Bi₂WO₆ appears as a secondary phase. The measured relative permittivity of Bi₂W₂O₉ ceramics increases continuously from 28.6 to 40.7 for compacts fired between 860° and 885°C. The bulk relative permittivity of Bi₂W₂O₉ corrected for porosity was calculated as 41.3. Bi₂W₂O₉ ceramics fired up to 875°C exhibit moderate quality factors, Q × f _r, ∼7500–7700 GHz and negative temperature coefficient of resonant frequency, ∼−54 to −63 ppm/°C. Chemical compatibility experiments show Bi₂W₂O₉ ceramics to react with both Ag and Cu electrodes, but to form good contacts with Au electrodes.     

High Electrical Conductivity and High Fracture Strength of Sc2O3-Doped Zirconia Ceramics with Submicrometer Grains

The microstructure, crystal phase, electrical conductivity, and mechanical strength of less than 7-mol%-Sc₂O₃-doped zirconia ceramics fabricated by comparatively low-temperature sintering at 1200–1300°C for 1 h were investigated. Zirconia ceramics having a uniform microstructure (grain size < 0.5 μm) stabilized with 6 mol% Sc₂O₃ showed high electrical conductivity (0.15 S/cm at 1000°C) and high fracture strength (660 MPa). With the increase of Sc₂O₃ content from 3.5 to 7 mol%, the grain size, fracture strength, and electrical conductivity at 1000°C changed from 0.2 to 0.5 μm, 970 to 440 MPa, and 0.07 to >0.2 S/cm, respectively. Sc₂O₃-doped zirconia polycrystals with high fracture strength and high electrical conductivity are promising candidates for the electrolyte material of solid oxide fuel cells.     

Synthesis and Characterization of MgAl2O4 Spinel Precursor from a Heterogeneous Alkoxide Solution Containing Fine MgO Powder

A precursor was synthesized from a heterogeneous alkoxide solution that contained fine MgO powder, which allowed the preparation of MgAl₂O₄ spinel powder with high sinterability characteristics. The precursor consisted of a mixture of boehmite (AlO(OH)) and a mixed hydroxide (Mg₄Al₂(OH)₁₄· 3H₂O). The spinel phase formed through two steps: (i) decomposition of the mixed hydroxide at low temperature and (ii) solid-state reaction between MgO and γ-Al₂O₃ at higher temperatures. Dense polycrystalline spinel could be obtained from the calcined powders at sintering temperatures as low as 1400°C.     

High-Temperature Strength of Liquid-Phase-Sintered SiC with AlN and Re2O3 (RE = Y, Yb)

Using AlN and RE₂O₃ (RE = Y, Yb) as sintering additives, two different SiC ceramics with high strength at 1500°C were fabricated by hot-pressing and subsequent annealing under pressure. The ceramics had a self-reinforced microstructure consisting of elongated α-SiC grains and a grain-boundary glassy phase. High-temperature strength up to 1600°C was measured and compared with that of the SiC ceramics fabricated with AlN and Er₂O₃. SiC ceramics with AlN and Y₂O₃ showed the best strength (∼630 MPa) at 1500°C, while SiC ceramics with AlN and Er₂O₃ the best strength (∼550 MPa) at 1600°C.     

Reaction Sintering of ZnO-AI2O3

The reaction sintering of equimolar mixtures of ZnO and A1₂O₃ powders was investigated as a function of primary processing parameters such as the temperature, heating rate, green density, and particle size. The powder mixtures were prepared by two different methods. In one method, the ZnO and A1₂O₃ powders were ball-milled. In the other method, the ZnO powder was chemically precipitated onto the A1₂O₃ particles dispersed in a solution of zinc chloride. The sintering characteristics of the compacted powders prepared by each method were compared with those for a prereacted, single-phase powder of zinc aluminate, ZnAl₂O₄. The chemical reaction between ZnO and A1₂O₃ occurred prior to densification of the powder compact and was accompanied by fairly large expansion. The mixing procedure had a significant effect on the densification rate during reaction sintering. The densification rate of the compact formed from the ball-milled powder was strongly inhibited compared to that for the single-phase ZnAl₂O₄ powder. However, the densification rate of the compact formed from the chemically precipitated mixture was almost identical to that for the ZnAl₂O₄ powder. The difference in sintering between the ball-milled mixture and the chemically precipitated mixture is interpreted in terms of differences in the microstructural uniformity of the initial powder compacts resulting from the different preparation procedures.     

Synthesis of Anatase-Type TiO2 Nanocrystallites Via a Redox Route

Anatase nanocrystallites showing high surface area (∼62 m²/g) and good photocatalytic property have been obtained by pyrolyzing at 600°C for 4 h an ammonium titanyl double sulfate precursor (α-(NH₄)₂TiO(SO₄)₂) synthesized via a redox approach, that is, by oxidizing an aqueous solution of titanium trichloride (TiCl₃) with ammonium peroxodisulfate ((NH₄)₂S₂O₈), followed by reacting with ammonium sulfate ((NH₄)₂SO₄).     

Fabrication and Luminescent Properties of Nd3+-Doped Lu2O3 Transparent Ceramics by Pressureless Sintering

The fabrication of transparent Nd³⁺ ion-doped Lu₂O₃ ceramics is investigated by pressureless sintering under a flowing H₂ atmosphere. The starting Nd-doped Lu₂O₃ nanocrystalline powder is synthesized by a modified coprecipitant processing using a NH₄OH+NH₄HCO₃ mixed solution as the precipitant. The thermal decomposition behavior of the precipitate precursor is studied by thermogravimetric analysis and differential thermal analysis. After calcination at 1000°C for 2 h, monodispersed Nd³⁺:Lu₂O₃ powder is obtained with a primary particle size of about 40 nm and a specific surface area of 13.7 m²/g. Green compacts, free of additives, are formed from the as-synthesized powder by dry pressing followed by cold isostatic pressing. Highly transparent Nd³⁺:Lu₂O₃ ceramics are obtained after being sintered under a dry H₂ atmosphere at 1880°C for 8 h. The linear optical transmittance of the polished transparent samples with a 1.4 mm thickness reaches 75.5% at the wavelength of 1080 nm. High-resolution transmission electron microscopy observations demonstrate a "clear" grain boundary between adjacent grains. The luminescent spectra showed that the absorption coefficient of the 3 at.% Nd-doped Lu₂O₃ ceramic at 807 nm reached 14 cm⁻¹, while the emission cross section at 1079 nm was 6.5 × 10⁻²⁰ cm².     

Fabrication of Textured Bi3NbTiO9 Ceramics

Highly textured Bi₃NbTiO₉ ceramics are fabricated by normal sintering from molten salt-synthesized plate-like crystallites. Fine Bi₃NbTiO₉ plate-like crystallites (∼1 μm) not only facilitate the densification, but also enhance texture in Bi₃NbTiO₉ ceramics. Weak-agglomerated platelets exhibit higher sinterability and can be densified at a temperature as low as 1000°C, which is about 100°C lower than that of equiaxed powders prepared by directly calcining Bi₃NbTiO₉ precursor. Meanwhile, the orientation degree of textured Bi₃NbTiO₉ ceramics increases with sintering temperature. Highly oriented Bi₃NbTiO₉ (orientation degree of ∼0.91) ceramic with a relative density of ∼92% is obtained at 1150°C. Because of the oriented grain microstructure, textured Bi₃NbTiO₉ ceramic exhibits anisotropic electrical properties.     

Effects of Silver Doping on the Sol–Gel-Derived Ba4(Nd0.7Sm0.3)9.33Ti18O54 Microwave Dielectric Ceramics

Tungstenbronze-type Ba₄(Nd_0.7Sm_0.3)_9.33Ti₁₈O₅₄ (BNST) microwave dielectric ceramics doped with 0–10 wt% silver (Ag) particles were successfully fabricated by a citrate sol–gel method. The influence of Ag doping on the sinterability, microstructure, bulk conductivity, and dielectric properties of BNST was investigated. The desired tungstenbronze-type phase was obtained at 900°–950°C. The sintering temperature of BNST decreased to 1100°C with the aid of a small amount of Ag addition (1 wt%). No chemical reaction between the tungsenbronze phase and Ag was detected. The particle size of the powders decreased with increasing Ag content up to 1 wt% and it then increased with a further increase in the Ag content. The dense fine-grained ceramics with submicrometer grains (∼300 nm) were obtained with 1 wt% Ag addition. The submicrometer-grained ceramics had excellent dielectric properties of ɛ_r∼81 and Q × f ∼11 000 GHz. Both the dielectric constant and dielectric loss significantly increased with large additions (>3 wt%) of Ag due to the percolation effect.