Heteroatom Effect on Star‐Shaped Hole‐Transporting Materials for Perovskite Solar Cells

Three new star‐shaped hole‐transporting materials (HTMs) incorporating benzotripyrrole, benzotrifuran, and benzotriselenophene central cores endowed with three‐armed triphenylamine moieties ( BTP‐1 , BTF‐1 , and BTSe‐1 , respectively) are designed, synthesized, and implemented in perovskite solar cells (PSCs). The impact that the heteroatom‐containing central scaffold has on the electrochemical and photophysical properties, as well as on the photovoltaic performance, is systematically investigated and compared with their sulfur‐rich analogue ( BTT‐3 ). The new HTMs exhibit suitable highest‐occupied molecular orbitals (HOMO) levels regarding the valence band of the perovskite, which ensure efficient hole extraction at the perovskite/HTM interface. The molecular structures of BTF‐1 , BTT‐3 , and BTSe‐1 are fully elucidated by single‐crystal X‐ray crystallography as toluene solvates. The optimized (FAPbI₃)_0.85(MAPbBr₃)_0.15‐based perovskite solar cells employing the tailor‐made, chalcogenide‐based HTMs exhibit remarkable power conversion efficiencies up to 18.5%, which are comparable to the devices based on the benchmark spiro‐OMeTAD. PSCs with BTP‐1 exhibit a more limited power conversion efficiency of 15.5%, with noticeable hysteresis. This systematic study indicates that chalcogenide‐based derivatives are promising HTM candidates to compete efficiently with spiro‐OMeTAD.     

Dopant‐Free Spiro‐Triphenylamine/Fluorene as Hole‐Transporting Material for Perovskite Solar Cells with Enhanced Efficiency and Stability

Chemical doping is often used to enhance electric conductivity of the conjugated molecule as hole‐transporting material (HTM) for the application in optoelectronics. However, chemical dopants can promote ion migration at the electrical field, which deteriorates the device efficiency as well as increases the fabrication cost. Here, two star HTMs, namely 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine) 9,9′‐spirobifluorene (Spiro‐OMeTAD) and poly(triarylamine) are subjeted to chemical combination to yield dopant‐free N2,N2,N2′,N2′,N7,N7,N7′,N7′‐octakis(4‐methoxyphenyl)‐10‐phenyl‐10H‐spiro[acridine‐9,9′‐fluorene]‐2,2′,7,7′‐tetraamine (SAF‐OMe). The power conversion efficiencies (PCEs) of 12.39% achieved by solar cells based on pristine, dopant‐free SAF‐OMe are among the highest reported for perovskite solar cells and are even comparable to devices based on chemically doped Spiro‐OMeTAD (14.84%). Moreover, using a HTM comprised of SAF‐OMe with an additional dopant results in a record PCE of 16.73%. Compared to Spiro‐OMeTAD‐based devices, SAF‐OMe significantly improves stability.     

Polyfluorene Derivatives are High‐Performance Organic Hole‐Transporting Materials for Inorganic−Organic Hybrid Perovskite Solar Cells

Photovoltaics based on organic?inorganic perovskites offer new promise to address the contemporary energy and environmental issues. These solar cells have so far largely relied on small‐molecule hole transport materials such as spiro‐OMeTAD, which commonly suffer from high cost and low mobility. In principle, polyfluorene copolymers can be an ideal alternative to spiro‐OMeTAD, given their low price, high hole mobility and good processability, but this potential has not been explored. Herein, polyfluorene derived polymers‐TFB and PFB, which contain fluorine and arylamine groups, are demonstrated and can indeed rival or even outperform spiro‐OMeTAD as efficient hole‐conducting materials for perovskite solar cells. In particular, under the one‐step perovskite deposition condition, TFB achieves a 10.92% power conversion efficiency that is considerably higher than that with spiro‐OMeTAD (9.78%), while using the two‐step perovskite deposition method, about 13% efficient solar cells with TFB (12.80%) and spiro‐OMeTAD (13.58%) are delivered. Photo­luminescence reveals the efficient hole extraction and diffusion at the interface between CH₃NH₃PbI₃ and the hole conducting polymer. Impedance spectroscopy uncovers the higher electrical conductivity and lower series resistance than spiro‐OMeTAD, accounting for the significantly higher fill factor, photocurrent and open‐circuit voltage of the TFB‐derived cells than with spiro‐MeOTAD.     

Dithieno[3,2‐b:2′,3′‐d]pyrrol‐Cored Hole Transport Material Enabling Over 21% Efficiency Dopant‐Free Perovskite Solar Cells

Dopant‐free hole transport materials (HTMs) are essential for commercialization of perovskite solar cells (PSCs). However, power conversion efficiencies (PCEs) of the state‐of‐the‐art PSCs with small molecule dopant‐free HTMs are below 20%. Herein, a simple dithieno[3,2‐b:2′,3′‐d]pyrrol‐cored small molecule, DTP‐C6Th, is reported as a promising dopant‐free HTM. Compared with commonly used spiro‐OMeTAD, DTP‐C6Th exhibits a similar energy level, a better hole mobility of 4.18 × 10^?4 cm² V^?1 s^?1, and more efficient hole extraction, enabling efficient and stable PSCs with a dopant‐free HTM. With the addition of an ultrathin poly(methyl methacrylate) passivation layer and properly tuning the composition of the perovskite absorber layer, a champion PCE of 21.04% is achieved, which is the highest value for small molecule dopant‐free HTM based PSCs to date. Additionally, PSCs using the DTP‐C6Th HTM exhibit significantly improved long‐term stability compared with the conventional cells with the metal additive doped spiro‐OMeTAD HTM. Therefore, this work provides a new candidate and effective device engineering strategy for achieving high PCEs with dopant‐free HTMs.     

Hole‐Transporting Materials Incorporating Carbazole into Spiro‐Core for Highly Efficient Perovskite Solar Cells

Hole‐transporting materials (HTMs) play a significant role in hole transport and extraction for perovskite solar cells (PeSCs). As an important type of HTMs, the spiro‐architecture‐based material is widely used as small organic HTM in PeSCs with good photovoltaic performances. The skeletal modification of spiro‐based HTMs is a critical way of modifying energy level and hole mobility. Thus, many spiro alternatives are developed to optimize the spiro‐type HTMs. Herein, a novel carbazole‐based single‐spiro‐HTM named SCZF‐5 is designed and prepared for efficient PeSCs. In addition, another single‐spiro HTM SAF‐5 with reported 10‐phenyl‐10H‐spiro[acridine‐9,9′‐fluorene] (SAF) core is also synthesized for comparison. Through varying from SAF core to SCZF core as well as comparing with the classic 9,9′‐spiro‐bifluorene, it is found that the new HTM SCZF‐5 exhibits more impressive power conversion efficiency (PCE) of 20.10% than SAF‐5 (13.93%) and the commercial HTM spiro‐OMeTAD (19.11%). On the other hand, the SCZF‐5‐based device also has better durability in lifetime testing, indicating the newly designed SCZF by integrating carbazole into the spiro concept has good potential for developing effective HTMs.     

Organic Ionic Plastic Crystals as Hole Transporting Layer for Stable and Efficient Perovskite Solar Cells

Organic ionic plastic crystals (OIPCs) are synthesized through a simple metal‐free, cost‐effective approach. The strategized synchronization of electron‐rich phenoxazine with benzimidazolium iodide (OIPC‐I) and bromide (OIPC‐Br) salts lead to enhanced hole mobility and conductivity of OIPCs which is suitable for an efficient alternative to conventional organic hole transporting materials (HTMs) for stable perovskite solar cells (PSCs). The fabricated PSCs with OIPC‐I as hole transporting layer yielded a power conversion efficiency of 15.0% and 18.1% without and with additive (Li salt) respectively, which are comparable with spiro‐OMeTAD based devices prepared under similar conditions. Furthermore, the PSCs with OIPCs show good stability compared to the spiro‐OMeTAD with or without additives. Here, first time benzimidazolium‐based OIPCs have been used as an alternative organic HTM for perovskite solar cells, which opens a window for the design of effective OIPCs for highly efficient PSCs with long‐term stability.     

Grain Boundary and Interface Passivation with Core–Shell Au@CdS Nanospheres for High‐Efficiency Perovskite Solar Cells

The plasmonic characteristic of core–shell nanomaterials can effectively improve exciton‐generation/dissociation and carrier‐transfer/collection. In this work, a new strategy based on core–shell Au@CdS nanospheres is introduced to passivate perovskite grain boundaries (GBs) and the perovskite/hole transport layer interface via an antisolvent process. These core–shell Au@CdS nanoparticles can trigger heterogeneous nucleation of the perovskite precursor for high‐quality perovskite films through the formation of the intermediate Au@CdS–PbI₂ adduct, which can lower the valence band maximum of the 2,2,7,7‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)9,9‐spirobifluorene (Spiro‐OMeTAD) for a more favorable energy alignment with the perovskite material. With the help of the localized surface plasmon resonance effect of Au@CdS, holes can easily overcome the barrier at the perovskite/Spiro‐OMeTAD interface (or GBs) through the bridge of the intermediate Au@CdS–PbI₂, avoiding the carrier accumulation, and suppress the carrier trap recombination at the Spiro‐OMeTAD/perovskite interface. Consequently, the Au@CdS‐based perovskite solar cell device achieves a high efficiency of over 21%, with excellent stability of ≈90% retention of initial power conversion efficiencies after 45 days storage in dry air.     

Hole Transport Materials Based on 6,12‐Dihydroindeno[1,2‐b]fluorine with Different Periphery Groups: A New Strategy for Dopant‐Free Perovskite Solar Cells

Although several hole‐transporting materials (HTMs) have been designed to obtain perovskite solar cells (PSCs) devices with high performance, the dopant‐free HTMs for efficient and stable PSCs remain rare. Herein, a rigid planar 6,12‐dihydroindeno[1,2‐b]fluorine (IDF) core with different numbers of bulky periphery groups to construct dopant‐free HTMs of IDF‐SFXPh, IDF‐DiDPA, and IDF‐TeDPA is modified. Thanks to the contributions of the planar IDF core and the twisted SFX periphery groups, the dopant‐free IDF‐SFXPh‐based PSCs device achieves a device performance of 17.6%, comparable to the doped 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD)‐based device (17.6%), with much enhanced device stability under glovebox and ambient conditions.     

Constructing CsPbBr3 Cluster Passivated‐Triple Cation Perovskite for Highly Efficient and Operationally Stable Solar Cells

Ion migration and phase segregation, in mixed‐cation/anion perovskite materials, raises a bottleneck for its stability improvement in solar cells operation. Here, the synergetic effect of electric field and illumination on the phase segregation of Cs_0.05FA_0.80MA_0.15Pb(I_0.85Br_0.15)₃ (CsFAMA) perovskite is demonstrated. CsFAMA perovskite with a CsPbBr₃‐clusters passivated structure is realized, in which CsPbBr₃‐clusters are located at the surface/interface of CsFAMA grains. This structure is realized by introducing a CsPbBr₃ colloidal solution into the CsFAMA precursor. It is found that CsPbBr₃ passivation greatly suppresses phase segregation in CsFAMA perovskite. The resultant passivated CsFAMA also exhibits a longer photoluminescence lifetime due to reduced defect state densities, produces highly efficient TiO₂‐based planar solar cells with 20.6% power conversion efficiency and 1.195 V open‐circuit voltage. The optimized devices do not suffer from a fast burn‐in degradation and retain 90% of their initial performance at maximum power under one‐sun illumination at 25 °C (65 °C) exceeding 500 h (100 h) of continuous operation. This result represents the most stable output among CsFAMA solar cells in a planar structure with Spiro‐OMeTAD.     

Highly Stable and Efficient Perovskite Solar Cells with 22.0% Efficiency Based on Inorganic–Organic Dopant‐Free Double Hole Transporting Layers

Most of the high performance in perovskite solar cells (PSCs) have only been achieved with two organic hole transporting materials: 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9‐spirobifluorene (Spiro‐OMeTAD) and poly(triarylamine) (PTAA), but their high cost and low stability caused by the hygroscopic dopant greatly hinder the commercialization of PSCs. One effective alternative to address this problem is to utilize inexpensive inorganic hole transporting layer (i‐HTL), but obtaining high efficiency via i‐HTLs has remained a challenge. Herein, a well‐designed inorganic–organic double HTL is constructed by introducing an ultrathin polymer layer dithiophene‐benzene (DTB) between CuSCN and Au contact. This strategy not only enhances the hole extraction efficiency through the formation of cascaded energy levels, but also prevents the degradation of CuSCN caused by the reaction between CuSCN and Au electrode. Furthermore, the CuSCN layer also promotes the formation of a pinhole‐free and compact DTB over layer in the CuSCN/DTB structure. Consequently, the PSCs fabricated with this CuSCN/DTB layer achieves the power conversion efficiency of 22.0% (certified: 21.7%), which is among the top efficiencies for PSCs based on dopant‐free HTLs. Moreover, the fabricated PSCs exhibit high light stability under more than 1000 h of light illumination and excellent environmental stability at high temperature (85 °C) or high relative humidity (>60% RH).     

Charge Generation and Photovoltaic Operation of Solid‐State Dye‐Sensitized Solar Cells Incorporating a High Extinction Coefficient Indolene‐Based Sensitizer

An investigation of the function of an indolene‐based organic dye, termed D149, incorporated in to solid‐state dye‐sensitized solar cells using 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxypheny‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) as the hole transport material is reported. Solar cell performance characteristics are unprecedented under low light levels, with the solar cells delivering up to 70% incident photon‐to‐current efficiency (IPCE) and over 6% power conversion efficiency, as measured under simulated air mass (AM) 1.5 sun light at 1 and 10 mW cm^?2. However, a considerable nonlinearity in the photocurrent as intensities approach “full sun” conditions is observed and the devices deliver up to 4.2% power conversion efficiency under simulated sun light of 100 mW cm^?2. The influence of dye‐loading upon solar cell operation is investigated and the thin films are probed via photoinduced absorption (PIA) spectroscopy, time‐correlated single‐photon counting (TCSPC), and photoluminescence quantum efficiency (PLQE) measurements in order to deduce the cause for the non ideal solar cell performance. The data suggest that electron transfer from the photoexcited sensitizer into the TiO₂ is only between 10 to 50% efficient and that ionization of the photo excited dye via hole transfer directly to spiro‐OMeTAD dominates the charge generation process. A persistent dye bleaching signal is also observed, and assigned to a remarkably high density of electrons “trapped” within the dye phase, equivalent to 1.8 × 10¹⁷ cm^?3 under full sun illumination. it is believed that this localized space charge build‐up upon the sensitizer is responsible for the non‐linearity of photocurrent with intensity and nonoptimum solar cell performance under full sun conditions.     

High Efficiency Planar p‐i‐n Perovskite Solar Cells Using Low‐Cost Fluorene‐Based Hole Transporting Material

For commercial applications, it is a challenge to find suitable and low‐cost hole‐transporting material (HTM) in perovskite solar cells (PSCs), where high efficiency spiro‐OMeTAD and PTAA are expensive. A HTM based on 9,9‐dihexyl‐9H‐fluorene and N,N‐di‐p‐methylthiophenylamine (denoted as FMT) is designed and synthesized. High‐yield FMT with a linear structure is synthesized in two steps. The dopant‐free FMT‐based planar p‐i‐n perovskite solar cells (pp‐PSCs) exhibit a high power conversion efficiency (PCE) of 19.06%, which is among the highest PCEs reported for the pp‐PSCs based on organic HTM. For comparison, a PEDOT:PSS HTM‐based pp‐PSC is fabricated under the same conditions, and its PCE is found to be 13.9%.     

Boosting the performance and stability of perovskite solar cells with phthalocyanine-based dopant-free hole transporting materials through core metal and peripheral groups engineering

Three novel dopant-free hole-transporting materials (HTMs) based on phthalocyanine core containing (4-methyl formate) phenoxy or (4-butyl formate) phenoxy as the peripheral groups with cupper or zinc as the core metals (CuPcNO₂-OMFPh, CuPcNO₂-OBFPh, ZnPcNO₂-OBFPh) were designed and synthesized. All of the phthalocyanine complexes show excellent thermal stabilities, appropriate energy levels and suitable hole mobilities. The potential of three HTMs were tested in perovskite solar cells (PSCs) and ZnPcNO₂-OBFPh based PSC obtained power conversion efficiency (PCE) of 15.74% under 100 mA cm⁻² standard AM 1.5G solar illumination. Most important of all, PSC based on ZnPcNO₂-OBFPh shows better stability than that of the other two phthalocyanines and Spiro-OMeTAD under continuous light irradiation at 60 °C and maximum power point tracking in ambient air without encapsulation after 500 h. The results show that the introduction of appropriate peripheral groups and core metals can improve the performance and stability of PSCs dramatically, which provides an alternative way to develop HTMs for efficient and stable PSCs.     

Self‐Crystallized Multifunctional 2D Perovskite for Efficient and Stable Perovskite Solar Cells

Recently, perovskite solar cells (PSC) with high power‐conversion efficiency (PCE) and long‐term stability have been achieved by employing 2D perovskite layers on 3D perovskite light absorbers. However, in‐depth studies on the material and the interface between the two perovskite layers are still required to understand the role of the 2D perovskite in PSCs. Self‐crystallization of 2D perovskite is successfully induced by deposition of benzyl ammonium iodide (BnAI) on top of a 3D perovskite light absorber. The self‐crystallized 2D perovskite can perform a multifunctional role in facilitating hole transfer, owing to its random crystalline orientation and passivating traps in the 3D perovskite. The use of the multifunctional 2D perovskite (M2P) leads to improvement in PCE and long‐term stability of PSCs both with and without organic hole transporting material (HTM), 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) compared to the devices without the M2P.     

Orientation-Engineered Small-Molecule Semiconductors as Dopant-Free Hole Transporting Materials for Efficient and Stable Perovskite Solar Cells

Crystallized p-type small-molecule semiconductors have great potential as an efficient and stable hole transporting materials (HTMs) for perovskite solar cells (PSCs) due to their relatively high hole mobility, good stability, and tunable highest occupied molecular orbitals. Here, a thienoacene-based organic semiconductor, 2,9-diphenyldinaphtho[2,3-b:2′,3′-f]thieno[3,2-b]thiophene (DPh-DNTT), is thermally evaporated and employed as the dopant-free HTM that can be scaled up for large-area fabrication. By controlling the deposition temperature, the molecular orientation is modulated into a dominant face-on orientation with π–π stacking direction perpendicular to the substrate surface, maximizing the out-of-plane carrier mobility. With an engineered face-on orientation, the DPh-DNTT film shows an improved out-of-plane mobility of 3.3 × 10⁻² cm² V⁻¹ s⁻¹, outperforming the HTMs reported so far. Such orientation-reinforced mobility contributes to a remarkable efficiency of 20.2% for CH₃NH₃PbI₃ inverted PSCs with enhanced stability. The results reported here provide insights into engineering the orientation of molecules for the dopant-free organic HTMs for PSCs.     

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

The performance of perovskite solar cells (PSCs) strongly depends on the electron transport layer (ETL), perovskite absorber, hole transport layer (HTL), and their interfaces. Herein, the first approach to utilize ultrathin 2D titanium‐carbide MXenes (Ti₃C₂T_x quantum dots, TQD) by engineering the perovskite/TiO₂ ETL interface and perovskite absorber and introducing Cu_1.8S nanocrystals to perfect the Spiro‐OMeTAD HTL is represented. A significant hysteresis‐free power conversion efficiency improvement from 18.31% to 21.64% of PSCs is achieved after modifications with the enhanced short‐circuit current density, open‐circuit voltages, and fill factor. Various advanced characterizations, including femtosecond transient absorption spectroscopy, electrochemical impedance spectroscopy, and ultraviolet photoelectron spectroscopy, elucidate that the TQD/Cu_1.8S significantly contribute to the improved crystalline quality of the perovskite film with its large grain size and improved electron/holes extraction efficiencies at perovskite/ETL and perovskite/HTL interfaces. Furthermore, the long‐time ambient and light stability of PSCs are largely boosted through the TQD and/or Cu_1.8S nanocrystals doping, originating from the better crystallization of perovskite, suppressing the film aggregation and crystallization of HTL, and inhibiting the ultraviolet‐induced photocatalysis of the ETL. The findings highlight the TQD and Cu_1.8S can act as a superfast electrons and holes tunnel for the optoelectronic devices.     

Pyrite‐Based Bi‐Functional Layer for Long‐Term Stability and High‐Performance of Organo‐Lead Halide Perovskite Solar Cells

Organo‐lead halide perovskite solar cells (PSCs) have received great attention because of their optimized optical and electrical properties for solar cell applications. Recently, a dramatic increase in the photovoltaic performance of PSCs with organic hole transport materials (HTMs) has been reported. However, as of now, future commercialization can be hampered because the stability of PSCs with organic HTM has not been guaranteed for long periods under conventional working conditions, including moist conditions. Furthermore, conventional organic HTMs are normally expensive because material synthesis and purification are complicated. It is herein reported, for the first time, octadecylamine‐capped pyrite nanoparticles (ODA‐FeS₂ NPs) as a bi‐functional layer (charge extraction layer and moisture‐proof layer) for organo‐lead halide PSCs. FeS₂ is a promising candidate for the HTM of PSCs because of its high conductivity and suitable energy levels for hole extraction. A bi‐functional layer based on ODA‐FeS₂ NPs shows excellent hole transport ability and moisture‐proof performance. Through this approach, the best‐performing device with ODA‐FeS₂ NPs‐based bi‐functional layer shows a power conversion efficiency of 12.6% and maintains stable photovoltaic performance in 50% relative humidity for 1000 h. As a result, this study has the potential to break through the barriers for the commercialization of PSCs.     

All‐Carbon‐Electrode‐Based Endurable Flexible Perovskite Solar Cells

Endured, low‐cost, and high‐performance flexible perovskite solar cells (PSCs) featuring lightweight and mechanical flexibility have attracted tremendous attention for portable power source applications. However, flexible PSCs typically use expensive and fragile indium–tin oxide as transparent anode and high‐vacuum processed noble metal as cathode, resulting in dramatic performance degradation after continuous bending or thermal stress. Here, all‐carbon‐electrode‐based flexible PSCs are fabricated employing graphene as transparent anode and carbon nanotubes as cathode. All‐carbon‐electrode‐based flexible devices with and without spiro‐OMeTAD (2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene) hole conductor achieve power conversion efficiencies (PCEs) of 11.9% and 8.4%, respectively. The flexible carbon‐electrode‐based solar cells demonstrate superior robustness against mechanical deformation in comparison with their counterparts fabricated on flexible indium–tin oxide substrates. Moreover, all carbon‐electrode‐based flexible PSCs also show significantly enhanced stability compared to the flexible devices with gold and silver cathodes under continuous light soaking or 60 °C thermal stress in air, retaining over 90% of their original PCEs after 1000 h. The promising durability and stability highlight that flexible PSCs are fully compatible with carbon materials and pave the way toward the realization of rollable and low‐cost flexible perovskite photovoltaic devices.     

Nonfullerene Electron Transporting Material Based on Naphthalene Diimide Small Molecule for Highly Stable Perovskite Solar Cells with Efficiency Exceeding 20%

This study reports a new nonfullerene electron transporting material (ETM) based on naphthalene diimide (NDI) small molecules for use in high‐performance perovskite solar cells (PSCs). These solar cells simultaneously achieve high power conversion efficiency (PCE) of over 20% and long‐term stability. New NDI‐ID (N,N′‐Bis(1‐indanyl)naphthalene‐1,4,5,8‐tetracarboxylic diimide) consisting of an N‐substituted indane group having simultaneous alicyclic and aromatic characteristics is synthesized by a low‐cost, one‐step reaction, and facile purification method. The partially flexible characteristics of an alicyclic cyclopentene group on indane groups open the possibility of low‐temperature solution processing. The conformational rigidity and aromaticity of phenyl and alicyclic groups contribute to high temporal stability by strong secondary bonds. NDI‐ID has herringbone packed semiconducting NDI cores that exhibit up to 0.2 cm² V^?1 s^?1 electron mobility in field effect transistors. The inverted PSCs based on CH(NH₂)₂PbI_3–xBr_x with NDI‐ID ETM exhibit very high PCEs of up to 20.2%, which is better than that of widely used PCBM (phenyl‐C61‐butyric acid methyl ester) ETM‐based PSCs. Moreover, NDI‐ID‐based PSCs exhibit very high long‐term temporal stability, retaining 90% of the initial PCE after 500 h at 100 °C with 1 sun illumination without encapsulation. Therefore, NDI‐ID is a promising ETM for highly efficient, stable PSCs.     

Benzodithiophene Hole‐Transporting Materials for Efficient Tin‐Based Perovskite Solar Cells

Developing efficient interfacial hole transporting materials (HTMs) is crucial for achieving high‐performance Pb‐free Sn‐based halide perovskite solar cells (PSCs). Here, a new series of benzodithiophene (BDT)‐based organic small molecules containing tetra‐ and di‐triphenyl amine donors prepared via a straightforward and scalable synthetic route is reported. The thermal, optical, and electrochemical properties of two BDT‐based molecules are shown to be structurally and energetically suitable to serve as HTMs for Sn‐based PSCs. It is reported here that ethylenediammonium/formamidinium tin iodide solar cells using BDT‐based HTMs deliver a champion power conversion efficiency up to 7.59%, outperforming analogous reference solar cells using traditional and expensive HTMs. Thus, these BDT‐based molecules are promising candidates as HTMs for the fabrication of high‐performance Sn‐based PSCs.