Parametric optimization of multiwalled carbon nanotube-assisted electric discharge machining of Al-10%SiCp metal matrix composite by response surface methodology

The demand for miniaturized products having a glossy surface or nano-level surface is increasing exponentially in automobile, aerospace, biomedical, and semiconductor industries. The mirror-like surface finish has generated a need to develop advanced machining processes. The addition of powder particle into electric discharge machining (EDM) oil is considered a promising technique to achieve surface integrity at the miniaturization level. In this research, the Al–10%SiC_p metal matrix composite (MMC) has been machined after mixing the appropriate amount of multiwalled carbon nanotubes (MWCNTs) into the EDM dielectric fluid. An advanced experimental setup has been designed and fabricated in the laboratory for conducting the experiments. This proposed technology is called nano powder mixed electric discharge machining (NPMEDM). The input parameters of NPMEDM are also optimized using central composite rotatable design (CCRD) based on response surface methodology (RSM) in order to obtain the best surface finish and material removal rate (MRR). The MRR has been increased by 38.22% and surface finish has been improved by 46.06% after mixing the MWCNTs into the EDM dielectric fluid. The results indicate that the combination of parameters A5, B5, C5, and D5 might have produced maximum MRR, whereas A1, B1, C1, and D3 have produced minimum surface roughness (SR).     

Influences of Process Parameters on MRR Improvement in Simple and Powder-Mixed EDM of AA6061/10%SiC Composite

In the present work, aluminum alloy 6061/10%SiC composite is machined using numerical controlled Z-axis (ZNC) electrical discharge machining (EDM) process. Improvement in material removal rate (MRR) is explored using tungsten powder suspended dielectric fluid in EDM process (powder-mixed electrical discharge machining (PMEDM)). Peak current, pulse on time, pulse off time, and gap voltage are studied as process parameters. Mathematical relation between process parameters and MRR is established on basis of response surface methodology. The results obtained are further compared with MRR achieved from machining using simple EDM. The existence of tungsten particles in kerosene resulted in 48.43% improvement in MRR. The influence of tungsten powder-mixed dielectric fluid on machined surface is analyzed using scanning electron microscope and energy dispersive spectroscopy (EDS). The results revealed improvement in surface finish and reduction in recast layer thickness with PMEDM. EDS analysis reported presence of tungsten and carbon in recast layer deposited on machined surface.     

Performance of Additive Mixed Kerosene–Servotherm in Electrical Discharge Machining of Monel 400™

In general, kerosene and commercial grade EDM oils are conventional dielectric fluids in electrical discharge machining (EDM), despite their poor performance measures being major drawbacks. The aim of this study was to develop a dielectric fluid offering good performance measures in the EDM process, by determining the appropriate proportion of kerosene–servotherm and analyzing its performance with and without the additive concentration in EDM of monel 400?. Sixteen samples of kerosene–servotherm of varying proportions were used in this study. The optimum proportion of kerosene–servotherm was found to be 75:25, which resulted in the highest material removal rate (MRR) as compared with tool wear rate (TWR), and surface finish was found to be poorer than when using kerosene alone. In addition, 1 l of kerosene–servotherm concentrated with 6 g of graphite powder (one micron) exhibited substantial improvement in MRR, surface finish, and TWR compared with conventional dielectric fluids. Therefore kerosene–servotherm (75:25) concentrated with 6 g/l of graphite powder can be accepted as a potential dielectric fluid offering high MRR along with enhanced surface finish in EDM.     

Parametric Evaluation on Near-Dry Electric Discharge Machining

Near-dry electric discharge machining (EDM) is an eco-friendly process. It does not produce toxic fumes and consequent health hazards. The near-dry EDM generally utilizes a mixture of two phase (liquid and air) dielectric for machining. This investigation reports the influence of four processing parameters, viz. current, flushing pressure, duty factor, and lift on three responses. The responses measured were material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The work material chosen was high speed steel (HSS). Mathematical models have been proposed herein for evaluation of the effect of processing parameters in near-dry EDM. These models were developed using response surface methodology (RSM). The experimental results reveal that the process parameters taken into consideration were significant for MRR. The TWR was negligible in near-dry EDM. This process gives a finer surface finish with thinner recast layer even at higher discharge energies as compared to conventional EDM.     

Investigation of magnetic field-assisted EDM of composites

The Electrical Discharge Machining (EDM) technique was performed under the magnetic field influence to determine the material removal mechanism as well as surface roughness (SR) of nonmagnetic material. This study presents an exploration of the hybrid EDM technique assisted by magnetic field, with an aim to improve process performance. Herein, magnetic field intensity, peak current, duration of pulse-on/off, tool electrode material, and SiC percentage distribution were opted as the machining parameters. The chosen parameters were analyzed for their effects on the material removal rate (MRR) and SR while machining of SiC-reinforced aluminum-based metal matrix composites. Taguchi methodology was adopted for optimization of process parameters to achieve better MRR and lower SR. The experimental results witnessed improved surface finish and enhanced material removal ability of the process and also inferred that the magnetic field-assisted EDM facilitated the process stability.     

Effect of Tool Rotation on MRR,TWR, and Surface Integrity of AISI-D3 Steel using the Rotary EDM Process

Electric discharge machining (EDM) is an acclaimed non-conventional machining process that is used for machining of hard or geometrically complex and electrically conductive materials which are extremely difficult to machine by conventional methods. One of the foremost demerits of this process is its very low material removal rate (MRR). For this, researchers have proposed some modifications like; providing rotational motion to the tool or workpiece, mixing of conducting fine powders (such as SiC, Cr, Al, graphite etc.) in the dielectric, providing vibrations to either the tool or the workpiece etc.

The present research examines how the MRR and tool wear rates (TWR) vary with the variation in the tool rotation speed and their effects on the surface integrity of the workpiece. The results obtained clearly indicate that the tool rotation significantly improves the average MRR up to 49%. Moreover, the average surface finish also gets improved by around 9–10% while using the rotational tool EDM. Due to the tool rotation, the recast layer thickness is less for the rotary EDM as compared with the stationary tool EDM process. Furthermore, the micro-cracking on the recast surface of the workpiece is also less for the rotary tool EDM as compared with the stationary tool EDM.     

Multiobjective optimization and analysis of copper–titanium diboride electrode in EDM of monel 400™ alloy

Electrical discharge machining (EDM) is one of the most accepted machining processes in the precision manufacturing industry. In EDM process, finding an alternative tool material is the demand in modern manufacturing industry. Therefore, an attempt had been made to fabricate copper–titanium diboride powder metallurgy electrode to test in EDM on monel 400? material. The experiments are planned using center composite second-order rotatable design and the model is developed by response surface methodology. The machining characteristics have analyzed using the developed model. In this study, four input parameters such as titanium diboride percentage, pulse current, pulse on time, and flushing pressure are selected to evaluate the material removal rate (MRR) and tool wear rate (TWR). The adequacy of the developed regression model has tested through analysis of variance test. The desirability-based multiobjective optimization is used to find the optimal process parameter which has given maximum MRR and minimum TWR. The optimum process parameters obtained were titanium diboride of 16%, pulse current of 6 A, flushing pressure of 1 Mpa, and pulse on time of 35?µs. The validity of the response surface model is further verified by conducting confirmation experiments.     

Experimental investigations into the performance of EDM using argon gas-assisted perforated electrodes

In the present work, a parametric study of EDM process using Argon-Gas-Assisted EDM (AGAEDM) with rotary tool during machining of high chromium high carbon diesteel has been performed. The pulse on time, tool rotation, discharge current, duty cycle, and gas pressure were selected as process factors. The effects of process factors were investigated on responses viz. surface roughness (SR), material removal rate (MRR), and electrode wear ratio (EWR). A comparison between solid tool, air-assisted tool, and argon-assisted tool has also been presented. It was found that EWR and SR were less during AGAEDM process as compared to rotary EDM(REDM) with solid tool and air-assisted EDM (AAEDM) with rotary tool under same process parameters. However, MRR was found to be higher in AAEDM process. The regression analysis and analysis of variance have been done to develop and find the adequacy of the developed models of MRR, EWR, and SR. It was observed that surface integrity of workpiece machined by AGAEDM was better than workpiece machined by AAEDM and conventional REDM process.     

Multi-objective parametric optimization of powder mixed electro-discharge machining using response surface methodology and non-dominated sorting genetic algorithm

Powder mixed electro-discharge machining (EDM) is being widely used in modern metal working industry for producing complex cavities in dies and moulds which are otherwise difficult to create by conventional machining route. It has been experimentally demonstrated that the presence of suspended particle in dielectric fluid significantly increases the surface finish and machining efficiency of EDM process. Concentration of powder (silicon) in the dielectric fluid, pulse on time, duty cycle, and peak current are taken as independent variables on which the machining performance was analysed in terms of material removal rate (MRR) and surface roughness (SR). Experiments have been conducted on an EZNC fuzzy logic Die Sinking EDM machine manufactured by Electronica Machine Tools Ltd. India. A copper electrode having diameter of 25?mm is used to cut EN 31 steel for one hour in each trial. Response surface methodology (RSM) is adopted to study the effect of independent variables on responses and develop predictive models. It is desired to obtain optimal parameter setting that aims at decreasing surface roughness along with larger material removal rate. Since the responses are conflicting in nature, it is difficult to obtain a single combination of cutting parameters satisfying both the objectives in any one solution. Therefore, it is essential to explore the optimization landscape to generate the set of dominant solutions. Non-sorted genetic algorithm (NSGA) has been adopted to optimize the responses such that a set of mutually dominant solutions are found over a wide range of machining parameters.     

Improving the machining performance characteristics of the µEDM drilling process by the online cryogenic cooling approach

Productivity and surface quality would significantly affect the performance of the micro electrical discharge machining process (µEDM). Thus, the machining performance would be enhanced by improving the material removal rate (MRR) and surface quality. In this investigation, cryogenic LN₂ cooling was introduced to the conventional µEDM setup for developing an innovative process of cryogenically cooled µEDM process (CµEDM). The favorable outcomes of this process were estimated by selecting discharge current (I_p) and pulse on duration (T_on) for determining the effects of the machining performance including MRR and surface integrity. Surface quality was also analyzed by microstructural analysis and a scanning electron microscope (SEM) for evaluating the effects of the cryogenically cooled µEDM process. The experimental result shows 54–62% improvement in MRR and 22–36% improvement in average roughness values. Hence, it is suggested that cryogenically cooled µEDM facilitates improvement in productivity and surface quality.     

Effect of deep cryotreated tungsten carbide electrode and SiC powder on EDM performance of AISI 304

Abstract

Powder mixed electric discharge machining (PMEDM) is a further advancement of conventional EDM process in which electrically conductive powder is suspended in the dielectric fluid to enhance the material removal rate (MRR) along with the surface quality. Cryotreatment is introduced in this process for improving the cutting tool properties as well as tool life. In this investigation, EDM is performed for the machining of AISI 304 stainless steel using cryotreated double tempered tungsten carbide electrode when SiC powder is suspended in the kerosene dielectric. The influence of process parameters viz. pulse on time, peak current, duty cycle, gap voltage and powder concentration on tool wear rate (TWR), surface roughness (R_a), and MRR has been studied. Metallographic analysis was carried out for the machined surfaces. By the addition of powder concentration and cryotreated double tempered electrode, significant improvement in the machining efficiency has been found out. When cryotreated electrode used MRR, TWR and R_a decreased by 12%, 24% and 13.3%, respectively and when SiC powder used MRR increased by 23.2%, TWR and R_a decreased by about 25% and 14.2%, respectively.     

Electrical Discharge Machining of Functionally Graded 15-35 Vol% SiCp/Al Composites

A functionally Graded 15-35 volume% silicon carbide particulate (SiC_p) reinforced Al359 metal matrix composite (SiC_p/Al MMC) was drilled by electrical discharge machining (EDM) to assess the machinability and workpiece quality. The machining conditions were identified for both the machining performance and workpiece quality of the EDM process, including some aspects of material removal mechanisms, material removal rate (MRR), electrode tool wear, and subsequent drilled hole quality including surface texture and roundness by using surface profilometry, coordinate measuring machine (CMM), and scanning electron microscopy (SEM). It was observed that the material removal rate increases with increasing peak current and pulse-on-time up to the optimal points and drops drastically thereafter. Higher peak current and/or pulse-on-time result in both the greater tool wear and the larger average diameter error. As the percentage of the SiC particles increases, MRR was increased and electrode wear was found to be decreased. At the EDM machined subsurface layer, the fragmented and melted SiC particles were observed under the SEM and EDX-ray examination.     

Examinations concerning the electric discharge machining of AZ91/5B4CP composites utilizing distinctive electrode materials

In this study, investigation has been conducted in the focus of obtaining better surface finish in the electro discharge machining (EDM) of AZ91/5B₄C_p magnesium composites using distinctive sort of anode viz. copper, tungsten–copper, brass, aluminum and 20Gr/AA6061 (GRAL-20) composites. The process parameters, pulse on time and current were performed to research the machining qualities through material removal rate (MRR) and tool wear rate (TWR). The machined composites were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The formation of black spots was observed on machining with copper–tungsten and these black spots were not found when GRAL-20 was used as electrode. Machined with GRAL-20 electrode leads to the increase in spark gap, hence adequate flushing occurs; it eliminates re-melted layers on machined surface results in better surface roughness value. The results revealed that GRAL-20 electrodes posses better MRR followed by copper electrode whereas tungsten–copper exhibits better TWR followed by GRAL-20 electrode.     

Constrained multi-objective optimization of EDM process parameters using kriging model and particle swarm algorithm

This paper investigates the highly nonlinear relationship between process parameters and machining responses, including material removal rate (MRR), surface roughness (SR), and electrode wear rate (EWR) of electric discharge machining (EDM) using Kriging model. Subsequently, an emerging multi-objective optimization algorithm called particle swarm is used to determine the best machining conditions that not only maximize the machining speed but also minimize the EWR with a constraint of the SR. The experiment was carried out with P20 steel on a CNC EDM machine using copper electrode. The research result shows that the MRR increases sharply when increasing the discharge current just like other researches pointed out. However, the relationship between EWR and current is complicated. EWR appears the minimum value when the current is around 30?A. The speed of change of MRR per unit of EWR is the highest when the SR is around 14.5?µm. The combination of Kriging regression model and particle swarm optimization is considered as an intelligent process modeling and optimization of EDM machining. The proper selection of process parameters helps the EDM operator to reduce the machining time and cost.     

Electrical Discharge Machining (EDM) Characteristics Associated with Electrical Discharge Energy on Machining of Cemented Tungsten Carbide

In this investigation, cemented tungsten carbides graded K10 and P10 were machined by electrical discharge machining (EDM) using an electrolytic copper electrode. The machining parameters of EDM were varied to explore the effects of electrical discharge energy on the machining characteristics, such as material removal rate (MRR), electrode wear rate (EWR), and surface roughness. Moreover, the effects of the electrical discharge energy on heat-affected layers, surface cracks and machining debris were also determined. The experimental results show that the MRR increased with the density of the electrical discharge energy; the EWR and diameter of the machining debris were also related to the density of the electrical discharge energy. When the amount of electrical discharge energy was set to a high level, serious surface cracks on the machined surface of the cemented tungsten carbides caused by EDM were evident.     

Performance evaluation of Al2O3 nano powder mixed dielectric for electric discharge machining of Inconel 825

Electrical discharge machining (EDM) process is popular for machining conductive and difficult-to-cut materials, but low material removal rate (MRR) and poor surface quality are major limitations of the process. These limitations can be overcome by adding the suitable powder in the dielectric. The powder particles influence electric field intensity during the EDM process which in turn improve its performance. The size (micro to nano) and properties of the mixed powder also influence the machining efficiency. In this regard, the objective of the present work is to study the performance of EDM process for machining Inconel 825 alloy by mixing Al₂O₃ nanopowder in deionized water. The experimental investigation revealed that maximum MRR of 47?mg/min and minimum SR of 1.487?µm, which are 44 and 51% higher in comparison to conventional EDM process, respectively, can be achieved by setting optimal combinations of process parameters. To analyze these observed process behavior, pulse-train data of the spark gap were acquired. The discharge waveform identifies the less arcing phenomenon in the modified EDM process compared to conventional EDM. Further, surface-topography of the machined surface was critically examined by capturing field emission scanning electron microscopy and atomic force microscopy images.     

Study of Magnetic Field-Assisted ED Machining of Metal Matrix Composites

The present study deals with an investigation of the hybrid electric discharge (ED) machining process executed in a magnetic field for improving process performance. Previous magnetic field-assisted electric discharge machining (MFAEDM) techniques, however, are limited to use with a class of magnetic workpieces. In this particular study, the magnetic field was coupled with the conventional EDM plasma zone to test the hybrid process on Al-based metal matrix composites (MMCs). The machining parameters, for instance, peak current as well as duration of pulse-on were selected to nail down thereafter effects on the response parameters like the material removal rate (MRR) and the surface integrity. The experimental results show an improvement of 12.9% MRR and reduction in recast layer formation at higher spark energy in the magnetic field environment. As the experimental outcome implied that the MFAEDM imparted appreciable process stability, a highly efficient pertinent process of EDM with high quality of the machined surface could be accomplished to satisfy modern industrial applications.     

Machining of a hybrid–metal matrix composite using an erosion–abrasion-based compound wheel in electrical discharge grinding

Machining of the composites made of matrix and reinforcement is always difficult for manufacturing industries due to their unusual properties. Among various existing traditional and non-traditional machining processes, erosion-based machining process i.e., Electrical Discharge Grinding (EDG) and the abrasion-based process i.e., Diamond Grinding (DG) have been shown their potential to machine such difficult-to-machine materials. The aims of the present study are to analyze the performances of the erosion–abrasion-based compound wheel during machining of the hybrid–metal matrix composite made of Aluminum–Silicon Carbide–Boron Carbide (Al/SiC/B₄C) by the stir casting method. The performances of the compound wheel have been tested on the EDM machine in the face grinding mode. The role of pulse current, pulse on-time, pulse off-time, wheel RPM, and abrasive grit number have been analyzed on the material removal rate (MRR) and average surface roughness (Ra). The experimental results showed that the machining with compound wheel gives higher MRR with better surface finish as compared to the uniform wheel. It has also been observed that MRR and Ra are highly affected by the pulse current, pulse on-time, and wheel RPM.     

Study of Electrical Discharge Machining Performance in Water-Based Working Fluid

In this study, the role of working fluid in electrical discharge machining (EDM) was investigated based on its electrical conductivity. The function of gas bubble in material removal process was studied by comparing the crater that formed in water discharge with that formed in air discharge. The mechanism of material removal for EDM in water-based working fluid was proposed by analyzing the discharge voltage. Experiments were conducted to learn the influence of discharge parameters and working fluid conductivity on the crater forming process. The detected discharge waveform demonstrated that the effect of electrolytic reaction in the discharge process could be controlled by changing the conductivity of the working fluid. This study shows that water-based working fluid has good application prospects in EDM machining.     

Performance evaluation of cryogenically assisted electric discharge machining (CEDM) process

The performance of cryogenically assisted electric discharge machining (CEDM) process has been evaluated in the presented research paper. The machining of cryogenically treated (CT) and cryogenically untreated (CUT) AISI D2 tool steel work specimens using cryogenically cooled (CC), CT, and CUT copper electrodes have been performed. The effects of various parameters, namely, workpiece condition, tool condition, nozzle flushing, peak current, duty cycle, pulse duration, and gap voltage, have been studied on the performance indicators, viz. the material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The best parametric combinations have been suggested to obtain the desired quality characteristics. The interaction effects among various parameters have also been presented. An increase of approximately 18% in MRR and a reduction of 26% and 11% in TWR and SR, respectively, were observed, during the machining through CEDM in contrast to EDM. The confirmatory experiments suggested that experimental values were in permissible agreement with the predicted values for all the performance measures. Finally, the comparison of the CEDM with that of EDM process, in the light of SEM graphs, has been presented.