Experimental investigation on performance of additive mixed dielectric during micro-electric discharge drilling on 316L stainless steel

This study investigates the impact of machining factors on the performance of additive mixed micro-electric discharge drilling of 316L stainless steel. The effects of three kinds of powder, powder concentration, voltage, capacitance, feed rate, and speed on tool wear rate, material removal rate, taper angle, and overcut (OC) were also investigated. The experimental results show that adding additives to the dielectric enhanced rate of material removal and reduced rate of tool wear significantly. Mixing powder with dielectric increased the length of the sparking, resulting in significant OC, and process performance also improved with the increase in amount of powder added. Further, scanning electron microscopy analysis was carried out to examine the surface characteristics and material migration properties, which confirmed that the properties of the machined surface are indeed significantly improved.     

Experimental investigation of water-in-oil nanoemulsion in sinking electrical discharge machining

The most common dielectric in sinking electrical discharge machining (EDM) is kerosene. However, kerosene is inflammable; besides, it can be decomposed and release harmful gases during machining process. And, owing to its low viscosity, using kerosene in sinking EDM has low machining efficiency. Accordingly, conventional sinking EDM using kerosene as dielectric has poor safety, unfriendly environment impact, and low machining efficiency. A new water-in-oil (W/O) nanoemulsion is presented in this paper. This W/O nanoemulsion not only can eliminate the hazards from kerosene to operator and environment but also improve the machining performance of conventional sinking EDM. This research aims to experimentally investigate the machining performance of W/O nanoemulsion in comparison with kerosene in sinking EDM at relatively low discharge energy. The effects of electrode material, electrode polarity, peak current, and pulse duration on machining performance are studied. The machined surface and recast layer of workpiece are characterized as well. The experimental results demonstrate that compared with kerosene, using W/O nanoemulsion in sinking EDM can obtain a higher material removal rate (MRR), a lower relative electrode wear rate (REWR), and a machined workpiece with fewer defects and thinner recast layer.     

Effect of Tool Rotation on MRR,TWR, and Surface Integrity of AISI-D3 Steel using the Rotary EDM Process

Electric discharge machining (EDM) is an acclaimed non-conventional machining process that is used for machining of hard or geometrically complex and electrically conductive materials which are extremely difficult to machine by conventional methods. One of the foremost demerits of this process is its very low material removal rate (MRR). For this, researchers have proposed some modifications like; providing rotational motion to the tool or workpiece, mixing of conducting fine powders (such as SiC, Cr, Al, graphite etc.) in the dielectric, providing vibrations to either the tool or the workpiece etc.

The present research examines how the MRR and tool wear rates (TWR) vary with the variation in the tool rotation speed and their effects on the surface integrity of the workpiece. The results obtained clearly indicate that the tool rotation significantly improves the average MRR up to 49%. Moreover, the average surface finish also gets improved by around 9–10% while using the rotational tool EDM. Due to the tool rotation, the recast layer thickness is less for the rotary EDM as compared with the stationary tool EDM process. Furthermore, the micro-cracking on the recast surface of the workpiece is also less for the rotary tool EDM as compared with the stationary tool EDM.     

Impact of induction hardened workpiece hardness on EDM performance

The objective of this research work is to correlate the impact of thermally induced workpiece hardness with electric discharge machining (EDM) performances and establishment of the modified property responsible for the deviation in change in behavior of output responses in sinking electrical discharge machining process. The response surface methodology with central composite design approach was applied with four controllable input parameters such as pulse-on-time (T_on), pulse-off time (T_off), peak current (I_P), and gap voltage (V) for experimental comparative study. In this current analysis, material removal rate, tool wear rate, and energy density were chosen as the desired response variables. It was observed that change in hardness through induction thermal hardening process of the base alloy had a predominant effect on the change in output responses such as material removal rate, tool wear rate, and energy density with strong confirmation. The modified electrical property associated with enhanced workpiece hardness was primarily responsible for alteration in EDM process behaviors. This preliminary assessment for the deviation in the performance of the EDM process with respect to change in hardness will be quite useful for the control settings in the job shop production planning for processing and modifying properties of induction hardened alloy steels.     

碳材料选择对锂空气电池放电性能的影响

锂空气电池的放电过程和放电容量与空气电极的组成密切相关。由于碳材料是空气电极的主要组成部分,故其本征属性会影响空气电池的性能。对几种碳材料的研究,发现电池在放电过程中放电产物附生于碳材料表面,且大尺寸中孔(30 nm)和大孔是放电反应的原发位置,同时,放电反应产物也存储在这些位置上。通过理想电极(CNTs)的对比实验也证实了这点。     

Machining Characteristics and Optimization of Machining Parameters of SKH 57 High-Speed Steel Using Electrical-Discharge Machining Based on Taguchi Method

The effects of the machining parameters in electrical-discharge machining (EDM) on the machining characteristics of SKH 57 high-speed steel were investigated. A well-designed experimental scheme was used to reduce the total number of experiments. Parts of the experiment were conducted with the L18 orthogonal array based on the Taguchi method. Moreover, the signal-to-noise ratios associated with the observed values in the experiments were determined by ANOVA and F-test. The significant parameters that critically influenced the machining characteristics were examined, and the optimal combination levels of machining parameters for material removal rate, electrode wear rate, and surface roughness were determined.     

Influence of materials and machining parameters on WEDM of Al/AlCoCrFeNiMo0.5 MMC

The current study intends to optimize the wire electric discharge machining (WEDM) parameters while machining the newer AlCoCrFeNiMo_0.5 high entropy alloy (HEA) particles-reinforced aluminum composites. AlCoCrFeNiMo_0.5 HEA particles produced through arc melting technique are reinforced here for different weight % (0%, 3%, 6%, 9%, 12%, and 15%) along with pure aluminum by the way of powder metallurgy. WEDM studies were conducted by varying the appropriate parameters, namely, pulse ON time, pulse OFF time, and wire feed. Based on the selected parameters, through Taguchi method L18 orthogonal array is designed; the optimal parameter combination for better surface finish, material removal rate (MRR), and reduced kerf width (KW) is identified. For better understanding, through ANOVA, also the effect of each input variables over these adopted response variables was analyzed. The yielded results reveal that addition of AlCoCrFeNiMo_0.5 HEA as reinforcement has considerable effect over the response variablessuch that MRR and KW reduces; surface roughness increases with increase in HEA %. ANOVA results confirm that pulse ON time has higher effect over the response variables than any other parameters involved for the study. Multi-objective optimization done through Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) methodology answers that MRR and surface finish have improved, whereas KW gets reduced noticeably.     

Experimental studies on electrical discharge wire cutting of Ni-rich NiTi shape memory alloy

The experimental investigation explores the effect of electrical discharge wire cutting (EDWC) variable parameters such as spark gap voltage, wire tension, pulse off time, wire feed rate, and pulse on time on the surface roughness, average cutting rate, and metallographic changes of Ni_55.95Ti_44.05 shape memory alloy (SMA). The spark gap voltage, pulse off time, and pulse on time have the significant effect on the surface roughness and average cutting rate, whereas wire tension and wire feed rate have the trifling effect. Ni_55.95Ti_44.05 SMA’s surface after EDWC is characterized by many discharge craters, microcracks, voids, and white layer of resolidified molten material. The elemental composition analysis of white layer using energy-dispersive spectroscopy divulges the deposition of the foreign element from the brass wire as well as the dielectric on the surface after EDWC. The machined surface as well as the wire electrode surface consists of various compounds of Ti, Ni, Zn, and Cu which have been identified by X-ray diffraction peak analysis.     

Influence of additive materials on the roughness of AISI D2 steel in electrical discharge machining (EDM) environment

The quality of the machined surface resulted from the electrical discharge machining (EDM) environment is not efficient according to the previous studies. One of the significant problems is the impedance of dielectric fluid, where it is contributing to focusing the plasma channel in a limited area. Hence, this behavior leads to appearing deep craters on the machined zone. The researchers have attempted to enhance the average of surface roughness by employing powder particles or surfactant as the additive materials in the dielectric fluid. Unfortunately, these studies did not present a comparison between these additive materials in this environment. Therefore, the present study aims to compare the performance of the average of surface roughness (R_a) for AISI D2 steel by utilizing Nano chromium powder (NCP) and Span-20. The present work has proved that the behavior of the average of surface roughness for this steel is dropping at the maximum level of Nano chromium powder concentration and pulse duration as compared to the behavior with the Span-20. Moreover, the best roughness was produced by this steel with Nano chromium powder at 2 g/L and 20 μs for this powder and the pulse duration.     

Influence of surface roughness created by admixing smaller particles on improving discharge particle flowability of main particles

Particle flowability can be improved by admixing with particles smaller than the main particles. However, the mechanism by which this technique improves flowability is not yet fully understood. In this study, we focused on vibrating discharge particle flowability as one type of flowability and investigated the influence of the main particle roughness created by the adhesion of the admixed particles on improving the flowability. The diameters of the main and admixed particles (MPs and APs) were 41.4 or 60.8?μm and 8 or 104?nm, respectively. The main and admixed particles were mixed in various mass ratios, and the discharge particle flow rates of the mixed particles were measured. Scanning electron microscopy images were acquired from two different angles to determine the three-dimensional surface roughness using image analysis software. We then calculated the coating structure parameters from the obtained three-dimensional surface roughness. The observed trends for improving the vibrating discharge particle flowability were found to differ from those reported for compression particle flowability. Furthermore, the main particle roughness conditions that led to the greatest improvement involved the presence of several admixed particle agglomerations between the main particles.     

Investigation on performance of abrasive water jet in machining hybrid composites

For machining of composites, abrasive water jet machining is widely employed. For assembly of the machine tool structure, production of slots is essential. In this paper, abrasive water jet machining of composite laminates was experimentally investigated for various cutting parameters in terms of average surface roughness (R_a) and kerf taper (K_t). By generating a response surface model, the experimental values obtained for quality characteristics (R_a and K_t) were empirically related to cutting parameters. The effects of cutting parameters on quality characteristics were analyzed by utilizing empirical models and also optimized within the tested range based on desirability approach. The optimum parameter levels were also validated by confirmation test. From this investigation, it is evident that for obtaining a minimum kerf taper, traverse speed, water pressure, and abrasive mass flow rate are significant parameters and for obtaining less surface roughness traverse speed is the significant parameter.     

Effects of deicers on the performance of concrete pavements containing air-cooled blast furnace slag and supplementary cementitious materials

This study investigates the effects of continuous deicer exposure on the performance of pavement concretes. For this purpose, the differences in the compressive strength, the changes in the dynamic modulus of elasticity (DME) and the depth of chloride ingress were evaluated during and after the exposure period. Eight different concrete mixtures containing two types of coarse aggregates (i.e. air-cooled blast furnace slag (ACBFS) and natural dolomite) and four types of binder systems (i.e. plain Type I ordinary portland cement (OPC) and three combinations of OPC with fly ash (FA) and/or slag cement (SC)) were examined. These mixtures were exposed to three types of deicers (i.e. MgCl₂, CaCl₂, and NaCl) combined with two different exposure conditions (i.e. freezing-thawing (FT) and wetting-drying (WD)). In cold climates, these exposure conditions are the primary durability challenges that promote the physical deterioration of concrete pavements. The results indicated that among the studied deicers, CaCl₂ had the most destructive effect on the tested concretes while NaCl was found to promote the deepest level of chloride ingress yet was shown to have the least damaging impact on concretes. The microstructure evaluation revealed that the mechanism of concrete deterioration due to the deicer exposure involved chemical reactions between the deicers and concrete hydration products. The use of FA or SC as partial replacements for OPC can offset the detrimental effects of both deicers and FT/WD cycles.     

Effect of deep cryotreated tungsten carbide electrode and SiC powder on EDM performance of AISI 304

Abstract

Powder mixed electric discharge machining (PMEDM) is a further advancement of conventional EDM process in which electrically conductive powder is suspended in the dielectric fluid to enhance the material removal rate (MRR) along with the surface quality. Cryotreatment is introduced in this process for improving the cutting tool properties as well as tool life. In this investigation, EDM is performed for the machining of AISI 304 stainless steel using cryotreated double tempered tungsten carbide electrode when SiC powder is suspended in the kerosene dielectric. The influence of process parameters viz. pulse on time, peak current, duty cycle, gap voltage and powder concentration on tool wear rate (TWR), surface roughness (R_a), and MRR has been studied. Metallographic analysis was carried out for the machined surfaces. By the addition of powder concentration and cryotreated double tempered electrode, significant improvement in the machining efficiency has been found out. When cryotreated electrode used MRR, TWR and R_a decreased by 12%, 24% and 13.3%, respectively and when SiC powder used MRR increased by 23.2%, TWR and R_a decreased by about 25% and 14.2%, respectively.     

Effects of electrode materials on freezing of supercooled water in electric freeze control

In order to clarify effects of electric charge on freezing of supercooled water, experiments were carried out with various kinds of electrodes in supercooled water. Water sample was kept in a test tube and cooled down at a constant cooling rate. When the water sample was maintained under a supercooling state, an electric charge was applied to the water sample with a small electric current. The degree of supercooling was measured continuously. Then the degree of supercooling at freezing was determined. Six kinds of materials were used for electrodes. Those materials were Aluminum, Copper, Argentum, Aurum, Platinum and Carbon. It was found that the effects of electric charge were distinct according to the material used for electrodes. The degree of supercooling at freezing was the lowest in the case of Aluminum. On the other hand, the highest value of the degree of supercooling at freezing was obtained in the case of carbon. The reason for the difference in the degree of supercooling at freezing by six materials was discussed.     

添加Y2O3对CuW触头材料性能的影响

采用熔渗法制备添加Y2O3的CuW合金,研究了添加Y2O3对CuW材料静态性能、真空电击穿性能及显微组织的影响.结果表明:Y2O3的添加量为0～0.4 %(质量分数)时,随着添加量的增加,合金的硬度逐渐升高,而电导率变化不大;当添加量为0.4%～1.2%时,硬度和电导率则明显下降.添加Y2O3相提高了CuW合金的耐电压强度,降低了材料的截流值.添加Y2O3的CuW合金阴极斑点较小,铜液的飞溅现象减少.     

Investigations of geometrical structure and morphology of samples made of hard machinable materials after wire electrical discharge machining and vibro‐abrasive finishing

In this article the results concerned influence of processing conditions of the wire electrical discharge machining and vibro‐abrasive machining on the surface layer and morphology of samples made of hard machinable materials used in aircraft industry like: Titanium 5553 β, Inconel 617, Hastelloy X and Magnesium AZ31 have been presented. For this purpose the cubic and cylindrical samples made of hard machinable alloys have been prepared using optimal electric parameters of wire‐cut electrical discharge machining and finally they have been polished using circular vibratory finishing technology and different ceramic shaped stones.     

Effects of the morphology of the electrode nanostructures on the performance of dye-sensitized solar cells

This article reports the performances of dye-sensitized solar cells based on different working electrode structures, namely (1) highly ordered arrays of TiO₂ nanorods, (2) highly ordered arrays of TiO₂ nanotubules of different wall thicknesses, and (3) sintered TiO₂ nanoparticles. Even though highest short-circuit current density was achieved with systems based on TiO₂ nanotubules, the most efficient cells were those based on ordered arrays of TiO₂ nanorods. This is probably due to the higher open-circuit photovoltage values attained with TiO₂ nanorods compared with TiO₂ nanotubules. The nanorods are thicker than the nanotubules and therefore the injected electrons, stored in the trap states of the inner TiO₂ particles, are shielded from recombination with holes in the redox electrolyte at open-circuit. The high short-circuit photocurrent densities seen in the ordered TiO₂ systems can be explained by the fact that, in contrast to the sintered nanoparticles, the parallel and vertical orientation of the ordered nanostructures provide well defined electron percolation paths and thus significantly reduce the diffusion distance and time constant.      

Effects of process parameters on fatigue behavior and surface integrity of tool steel produced by electrical discharge turning

Electrical discharge machining is used in the production of countless parts with complex geometries and micro dimensions, from many elements of industrial molds to parts of motors and pumps. Also, most of these parts are cylindrical and it is always more meaningful to study their rotational fatigue behavior to predict their response during their operation. This study concentrated on the impacts of machining parameters on the surface quality and fatigue behavior of tool steel shaped by electrical discharge turning. The results based on Taguchi methodology have shown that discharge current affects R_a and R_z more, and pulse duration more affects the mean spacing of profile irregularities, S_m. As a result of the heat affected depth in the machined region, which changes in proportional with the processing parameters, the microhardness decreased from the sample surface to the core. The maximum hardness was measured at current of 12 A, pulse duration of 3 μs and pulse interval of 7 μs. According to the fatigue tests, it was found that the fatigue life decreased with the increase in R_z and S_m values. Moreover, high microhardness and thick recast layer reduced the fatigue strength of the samples with relatively smooth surface topography.     

Effects of discharging vibration conditions and coating structures on improving discharge particle flowability in a smaller particle admixing system

Particle flowability can be improved by admixing particles smaller than the original particles (main particles). However, the effects of coating structures on the improvement of flowability are not yet fully understood. In this study, we focused on vibrating discharge particle flowability and investigated the effect of discharging vibration conditions and coating structures on improving the flowability. Main and admixed particles of 60.8 μm and 8 nm in diameter, respectively, were mixed in various mass ratios, and the discharge particle flow rates of the mixed particles were measured. Scanning electron microscopy and scanning probe microscopy images were used to analyze the coverage diameter, surface coverage ratio, and coverage height of the admixed particles on the main particle surfaces. As a result, the admixing mass ratio that gave maximum flowability was found to depend on the maximum value of the vibration acceleration. This could be explained by the relationship between the coating structures of admixed particles and the coated average surface distances due to the vibration acceleration.