共查询到18条相似文献,搜索用时 140 毫秒
1.
化学镀镍-铜-磷三元合金工艺的研究 总被引:1,自引:2,他引:1
为提高化学镀镍-磷合金镀层的性能及获得多种性能的合金镀层以拓宽其应用范围。在化学镀镍-磷合金液中加入硫酸铜制得镍-铜-磷三元合金。研究了镀液中硫酸镍、次磷酸钠、柠檬酸钠、硫酸铜、稳定剂、光亮剂的含量以及pH值和温度等因素对合金镀层的外观、沉积速度及铜含量的影响。通过5%氯化钠溶液和10%硫酸溶液浸泡试验比较了所得镍-铜-磷合金镀层与镍-磷合金镀层以及前人制得的镍-磷合金镀层的耐蚀性,同时比较了上述镀层的其它性能。结果表明,所得镍-铜-磷合金镀层的耐蚀性、外观、结合力、孔隙率、沉积速度、硬度和耐磨性等性能优于镍-磷合金及前人制得的镍-铜-磷合金镀层。 相似文献
2.
化学镀镍铜磷三元合金沉积工艺的研究 总被引:7,自引:1,他引:7
为提高化学镀镍的硬度、耐磨及耐蚀性,以拓宽在电子工业中应用,采用在化学镀镍磷合金液中添加适量的铜离子制得镍铜磷三元合金。研究了镍离子与铜离子浓度比、次磷酸钠含量、沉积温度对合金镀层沉积速率的影响,利用S-570扫描电镜和H-800透电镀观察了镀层表面形貌和显微组织,通过硝酸腐蚀试验比较了镍磷合金与镍铜镀层的耐蚀性。结果表明,铜的共沉积能明显提高镍磷合金的耐蚀性。 相似文献
3.
4.
5.
在乙酸盐-铵盐体系电镀锌–镍合金镀液配方中添加次磷酸钠,以45钢为基体电沉积锌–镍–磷合金。通过循环伏安法和小槽电镀实验研究了pH、温度和电流密度对镀层成分的影响,采用扫描电镜、能谱、X射线荧光、X射线衍射等技术对镀层形貌和微观组织进行表征,采用Tafel极化曲线和电化学阻抗谱对镀层的耐蚀性进行测试。结果表明:在不含主盐的基础镀液中,次磷酸钠的P不能被还原出来,而次磷酸钠与Zn2+、Ni2+共存时有助于Ni的沉积,对Zn的沉积无明显影响;温度升高则镀层中Zn减少,Ni和P增多;降低pH有利于锌–镍共沉积;镀层的P含量随电流密度增大而减少。P元素的掺入能完全消除锌-镍合金的裂纹,细化镀层晶粒。低P含量(P质量分数低于1%)的锌–镍–磷合金镀层具有比高P含量(P质量分数大于10%)的镀层更好的耐蚀性。 相似文献
6.
7.
利用化学沉积方法在铝合金表面制备镍-磷合金镀层。讨论工艺参数对合金镀层表面形貌、相结构及耐蚀性的影响。结果表明:温度对合金镀层表面形貌的影响较大,而对相结构的影响较小。在84℃下获得的合金镀层具有较好的耐蚀性。 相似文献
8.
电镀非晶态镍磷合金的研究 总被引:10,自引:2,他引:8
采用亚磷酸-镍盐体系制得光亮镍磷镀层,研究了镀液组成,电流密度,温度等对镀层性能和电流效率的影响,优选出分别获得最佳镀层耐蚀性,硬度和电流效率的工艺条件;分析了耐蚀非晶态镍磷合金镀层的形成原因,即在电镀过程中,镀层形成了类似Ni3P的稳定结构。 相似文献
9.
本文介绍了几种考虑可节镍代镍工艺;认为厚铜薄镍镀层组合可以得到双层镍铬镀层一样的耐蚀性,还可根据产品使用条件,选用光亮低锡青铜可部分代铜或节镍;介绍了用锌基合金、锌铁合金、锌铜合金、锡镍锌三元合金等工艺的特性与有待解决的问题;最后提及了新型阳极材料。文中有关工艺,推荐了有代表性的配方与工艺条件。 相似文献
10.
11.
化学镀Ni-P合金层耐蚀性能的研究 总被引:5,自引:0,他引:5
通过中性盐雾试验、极化曲线测验、X射线衍射和扫描电镜等手段研究了影响化学镀Ni-P合金镀层耐蚀性能的各种因素。认为镀层的含磷量随镀液中次磷酸钠浓度、络合剂浓度或镀液温度的增高而提高,但随镀液pH值的增高而减低。而含磷量较高的镀层具有较高的耐蚀性能。研究还表明,镀件在化学镀前经过抛光处理会有助于提高镀层的耐蚀性。而镀后在高温度下的热处理,则会使镀层的耐蚀性变差。 相似文献
12.
钨对化学镀Ni-W-P合金镀层结构及性能的影响 总被引:4,自引:0,他引:4
通过不同的化学镀工艺配方,获得了4种不同钨含量的化学镀Ni-W-P三元合金镀层.研究了钨含量对镀层结构、硬度及在5%H2SO4溶液中耐蚀性的影响规律.研究发现,化学镀Ni-W-P三元合金镀层的结构受镀层中钨含量的影响较大,非晶态Ni-W-P三元合金镀层所需磷含量较非晶态Ni-P二元镀层所需磷含量要低,并且钨含量越高,所需磷含量越少;镀层硬度随镀层结构从非晶态→混晶态→纳米晶态转变而增加;镀层的耐蚀性随镀层中钨含量增加而变好,且非晶态镀层较混晶态和纳米晶态镀层更易形成钝化区. 相似文献
13.
Wenfeng Qin 《Journal of Coatings Technology and Research》2011,8(1):135-139
The microstructure and corrosion behavior of electroless Ni–P alloy plating on 6061 aluminum alloys substrate in an alkaline
plating bath with sodium hypophosphite as reducing agent were investigated. The effects of bath temperature on the plating
rate, compositions, and microstructure of the electroless Ni–P deposits were studied. The results showed that the deposition
rate and the P content of the electroless Ni–P deposits increased with the rise of the bath temperature. Scanning electron
microscopy (SEM) of the deposits showed nodular structure for binary deposits. X-ray diffraction patterns of all the deposits
revealed a single and broad peak which indicated the amorphous structure of the deposits. Corrosion resistance of the Ni–P
coatings was evaluated by potentiodynamic polarization. The results indicated that electroless Ni–P plating could obviously
improve the corrosion resistance of 6061 aluminum alloy. 相似文献
14.
15.
16.
M. Bouanani F. Cherkaoui R. Fratesi G. Roventi G. Barucca 《Journal of Applied Electrochemistry》1999,29(5):637-645
Electroless Ni–Zn–P alloy coatings were obtained on an iron substrate from a sulfate bath at various pH values. The effects of changes in bath pH on alloy composition, morphology, microstructure and corrosion resistance were studied. Scanning electron microscopy was performed to observe the morphological change of the deposits with bath pH. Coating crystallinity was investigated by grazing incidence asymmetric Bragg X-ray diffraction and transmission electron microscopy. A transition from an amorphous to polycrystalline structure was observed on increasing the bath alkalinity, and thus decreasing the phosphorus content of the alloys. A single crystalline phase corresponding to face-centred-cubic nickel was identified in the alloys obtained from a strong alkaline solution. An increase in zinc percentage up to 23% in the deposits does not change the f.c.c. nickel crystalline structure. Corrosion potential and polarization resistance measurements indicated that the corrosion resistance of electroless Ni–Zn–P alloys depends strongly on the microstructure and chemical composition. The deposits obtained at pH 9.0–9.5 and with 11.4–12.5% zinc and 11.8–11.2% phosphorous exhibited the best corrosion resistance. 相似文献
17.