New hyperbranched polymers containing second-order nonlinear optical chromophores: Synthesis and nonlinear optical characterization

Three hyperbranched polymers (P1-P3) containing second-order nonlinear optical chromophores were synthesized by copolymerization of aromatic dialdehydes (carbazole, triphenylamine or benzene moieties) with sulfonyl-based chromophores attached with three active methylene groups, from “A₂ + B₃” approach based on simple Knoevenagel reaction. For comparison, their corresponding linear analogue polymers (P4-P6) were prepared. All the polymers are soluble in common organic solvents, and exhibit good thermal stability. The tested NLO properties of the hyperbranched polymers are better than their corresponding linear polymers, due to the three-dimensional spatial separation of the chromophores in the obtained hyperbranched polymeric structures.     

Colorless polyimides from 2,3,3′,4′-biphenyltetracarboxylic dianhydride (α-BPDA) and various aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A series of organosoluble and light-colored polyimides (III) was prepared from 2,3,3′,4′-biphenyltetracarboxylic dianhydride (α-BPDA) with various fluorinated aromatic bis(ether amine)s via two-step method with thermal or chemical imidization of poly(amic acid)s yielded polyimides. The III series had inherent viscosity of 0.74-1.01 dl/g and showed excellent solubility in a variety of organic solvents. They were soluble in the amide polar solvent, ether-type solvent, and chlorinated solvent. These polyimide films also showed a high optical transparency and less color intensity, with an ultraviolet-visible absorption edge of 369-382 nm and low b^* values (a yellowness index) of 5.0-11.7. Glass-transition temperature of the III series was recorded at 244-319 °C and higher than the isomeric polyimides V series. Compared with the nonfluorinated polyimides IV, the III series showed lighter-colored and lower dielectric constants and moisture absorptions. The good tensile properties and excellent thermal properties of the III series were also observed.     

Synthesis of novel poly{methyl-[3-(9-indolyl)propyl]siloxane}-based nonlinear optical polymers via postfunctionalization

A novel series of nonlinear optical (NLO) polysiloxanes with a high density of chromophore moieties based on poly{methyl-[3-(9-indolyl)propyl]siloxane} (PMIPS) were synthesized by a post functional strategy. First, PMIPS (P1) was prepared through hydrosilylation reaction, then P1 is partially formylated by the reaction between P1 and the reagents of dimethylformamide (DMF) and phosphorus oxychloride under the standard Vilsmeier reaction conditions, and these formyl groups with high reactivity are condensed with four predesigned cyanoacetylated chromophores to afford the series of chromophore functionalized polysiloxanes (P3-6). The most special point is the molar concentrations of chromophore moieties are the same in polymers P3-6, which makes it convenient to study the behavior of different chromophores in the polymeric system. The poled films of P3-6 reveal the resonant d₃₃ values in the range of 7.9-55.2 pm/V by second harmonic generation (SHG) measurements.     

Properties of organosoluble aromatic polyimides from 3′-trifluoromethyl-3,4′-oxydianiline

A colorless fluorinated diamine, 3′-trifluoromethyl-3,4′-oxydianiline (3′-CF₃-3,4′-ODA) (II) was prepared through the nucleophilic substitution reaction of 3-nitrophenol and 2-chloro-5-nitrobenzotrifluoride by catalytic reduction with hydrazine and Pd/C. A series of Polyimides V were synthesized from the diamine II with various aromatic dianhydrides III_a-f via thermal and chemical imidization. These polyimides had inherent viscosities ranging from 0.88 to 1.12 dl/g. A comparison of V, VI to analogous polyimides VII, VIII. VI, VII and VIII was based on 3′4-ODA, 3-CF₃-4,4′-ODA, 4,4′-ODA, respectively. In terms of the color of PI revealed that the color intensity of phenoxy-containing amine of the meta-structure and the para-structure with the CF₃ group would fell off color intensity. The color intensity of the four polyimide series was lessened in the following order: V>VII>VI>VIII. The solubility of V is better than VI, VII and VII. The polyimide V films had a tensile strength ranging from 124 to 147 MPa, elongation at break from 9 to 65%, and initial modulus from 2.3 to 2.8 GPa. The glass transition temperature of polymers was recorded at 234-313 °C. They had 10% weight loss at a temperature above 515 °C and left more than 50% residue even at 800 °C in nitrogen. Compared with polyimides VI, V showed the lower dielectric constants of 2.80-3.50 (40 MHz), and moisture absorptions in the range of 0.44-1.02 wt%.     

Highly optically transparent/low color polyimide films prepared from hydroquinone- or resorcinol-based bis(ether anhydride) and trifluoromethyl-containing bis(ether amine)s

Two series of novel polyimides (5a-g and 6a-g) containing flexible ether linkages and pendent trifluoromethyl (CF₃) groups were synthesized from 1,4-bis(3,4-dicarboxyphenoxy)benzene dianhydride (3a) and 1,3-bis(3,4-dicarboxyphenoxy)benzene dianhydride (3b) with various CF₃-substituted aromatic bis(ether amine)s (4a-g) via ring-opening polyaddition to poly(amic acid)s, followed by thermal or chemical imidization. These polyimides were readily soluble in a variety of organic solvents and could be solution-cast into flexible and tough films. The cast films exhibited high optical transparency and almost no color, with a UV-vis absorption edge of 368-382 nm and a very low b^∗ value (a yellowness index) of 6.2-15.5. They had good thermal stability with glass-transition temperatures of 186-288 °C, and most of them did not show significant decomposition before 500 °C. Moreover, these polyimide films also possessed low dielectric constants of 2.79-3.49 (at 1 MHz) and low water uptakes (<0.65 wt%).     

Controlling nonlinear optical effects of polyurethanes by adjusting isolation spacers through facile postfunctional polymer reactions

With the aim to control nonlinear optical (NLO) effects of polyurethanes, especially to efficiently translate the fixed μβ values of the organic chromophore to possibly higher macroscopic NLO activities of polymers, a facile synthetic strategy, consisting of the postazo coupling and esterification reactions, was developed to prepare a series of second-order nonlinear optical polyurethanes (P2-P5). And in the polymers, different isolation groups were introduced to the sulfonyl-based chromophore moieties at the acceptor side. Thus, polyurethane P1 containing aniline groups was obtained from the copolymerization of 2,4-toluenediisocyanate (TDI) and N,N-2-(2-hydroxyethyl)aniline directly; then a postazo coupling reaction of p-(2-hydroxyethyl)sulfonylbenzenediazonium fluoroborate toward the aniline ring afforded the sulfonyl-based chromphore-functionalized polyurethane P2, which underwent the subsequent esterification reactions between the hydroxyl groups in P2 and different organic acids to link different isolation spacers (changing from small groups to much larger ones such as carbazolyl groups), to the chromophore moieties at the acceptor side, to yield polyurethanes P3, P4 and P5. The polymers exhibit good solubility in common organic solvents and are thermally stable. The maximum absorption appeared at about 436 nm with a cutoff at ca. 570 nm, resulting in a wider transparency window. The tested NLO properties demonstrate that the resonant d₃₃ values of polymers could be improved about 1.5 times by attaching isolation spacers with suitable bulkiness.     

Effects of internal linkage groups of fluorinated diamine on the optical and dielectric properties of polyimide thin films

To investigate the difference of the trifluoromethyl (CF₃) group and ether group affecting the optical property of fluorinated polyimides (PIs), we prepared 4,4′-bis(4-amino-2-trifluoromethylphenoxy)diphenyl ether (4) with three ether groups and 2,2-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]hexafluoropropane (5) with four CF₃ groups with 2-chloro-5-nitrobenzotrifluoride and 4,4′-dihydroxydiphenyl ether or 2,2-bis(4-hydroxyphenol)hexafluoropropane. Two series of organosoluble and light-colored PIs (4a-4c, 5a-5c) were synthesized from 4 and 5 with various aromatic dianhydrides: 3,3,4,4-benzophenonetetracarboxylic dianhydride (BTDA) (a), 4,4-oxydiphthalic anhydride (ODPA) (b), and 4,4-hexafluoroisopropylidenediphthalic anhydride (6FDA) (c), prepared through a typical two-step polymerization method. These PIs were soluble in amide polar solvents and even in less polar solvents. The glass-transition temperatures (T_g) of 4a-5c were 221-249 °C and the 10% weight-loss temperatures were above 530 °C. Their films had cutoff wavelengths between 339 and 399 nm and yellowness index ranges from 1.95 to 42.60. The dielectric constants estimated from the average refractive indices are 2.59-2.93 (1 MHz). In a comparison of the PI series based on 4, 5, and 4,4′-bis(4-amino-2-trifluoromethylphenoxy)biphenyl (6), we found that the CF₃ group and ether group on the diamine had almost same effect in lowering the color, but the ether group had better thermal stability. The color intensity of the three PI series was lowered in the following order: 6 > 4 > 5. The PI 5c, synthesized from diamine 5 and dianhydride c, had six CF₃ groups in a repeated segment and ether group at the same time, so it exhibited the lightest color among the three series.     

Synthesis, characterization, and high gas permeability of poly(diarylacetylene)s having fluorenyl groups

Diarylacetylenes having fluorenyl groups and other substituents (trimethylsilyl, t-butyl, bromine, fluorine) (1a-1) were polymerized with TaCl₅-n-Bu₄Sn. Monomers 1a-l produced high molecular weight polymers 2a-l (M_w 5.1 × 10⁵-1.3 × 10⁶) in 12-59% yields. All of the polymers were soluble in common organic solvents, and gave tough free-standing membranes by the solution casting method. The onset temperatures of weight loss of polymers 2a-l in air were over 400 °C, indicating considerably high thermal stability. All the polymer membranes showed high gas permeability; e.g., the oxygen permeability coefficient (PO₂) of 2a was as large as 4800 barrers. Membrane 2d possessing two fluorine atoms at meta and para positions of the phenyl ring showed the highest oxygen permeability (PO₂ = 6600 barrers) among the present polymers.     

Second-order nonlinear optical (NLO) polymers containing perfluoroaromatic rings as isolation groups with Ar/Ar self-assembly effect: Enhanced NLO coefficient and stability

Four new polyaryleneethynylenes P1–P4, which contained different aromatic or perfluoroaromatic isolation groups, were successfully prepared, via the palladium-catalyzed Sonogashira coupling reaction. Among them, P2, due to the presence of the self-assembly effect between the perfluoroaromatic and chromophore moieties, demonstrated much larger NLO effect (d₃₃ value of 162.3 pm/V) and better stability with onset temperature for decay (111 °C). The research on the polymer conformation suggested that perfluorophenyl groups in different positions would result in different effects on the NLO coefficient, providing some useful information for the design of NLO polymers with better performance.     

Colorless and high organosoluble polyimides from 2,5-bis(3,4-dicarboxyphenoxy)-t-butylbenzene dianhydride and aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A series of polyimides III_a-h characterized by colorlessness, high transparency, high solubility, and good mechanical property, was synthesized from the aromatic dianhydride, 2,5-bis(3,4-dicarboxyphenoxy)-t-butylbenzene dianhydride (I), and various aromatic diamines (II_a-h) with pendent trifluoromethyl group via polyaddition, chemical imidization, and direct cast films. The III series showed more colorless than the polyimides (V and VI series) of 2,2-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) contained, the VI series was synthesized from the II with 6FDA. These films III had cut-off wavelengths between 371 and 376 nm, as well as b* value (a yellowness index) ranging from 3.0 to 4.7. In fact, it is so far the most colorless aromatic polyimide in our systematical researches. The III series had inherent viscosity ranging from 0.72 to 1.33 dL/g and showed excellent solubility in a variety of organic solvents. They were soluble in a concentration of 5-10% in the amide polar solvent, ether solvent, and chlorinated solvent. These films showed strength tensile of 97-123 MPa, dielectric constants of 2.78-3.28 (1 MHz), and moisture absorptions of 0.11-0.36 wt%. The glass transition temperature of the III series was recorded at 214-259 °C, the 10% weight loss temperature was over 468 °C, and the residue was more than 47% at 800 °C in nitrogen.     

New host copolymers containing pendant triphenylamine and carbazole for efficient green phosphorescent OLEDs

A series of vinyl copolymers (P1-P6) containing pendant hole-transporting triphenylamine (11-88 mol%) and carbazole chromophores were synthesized by radical copolymerization to investigate the influence of triphenylamine groups upon optoelectronic properties. The copolymers were readily soluble in common organic solvents and their weight-average molecular weights (M_ws) were between 1.41 × 10⁴ and 2.24 × 10⁴. They exhibited moderate thermal stability with T_d = 402-432 °C at 5% weight loss. The emission spectra (both PL and EL) of the blends [P1-P6 with 4 wt% Ir(ppy)₃] showed dominant green emission (517 nm) attributed to Ir(ppy)₃ due to efficient energy transfer from P1-P6 to Ir(ppy)₃. The HOMO levels of P1-P6, estimated from onset oxidation potentials in cyclic voltammeter, were −5.42 to −5.18 eV, which are much higher than −5.8 eV of conventional poly(9-vinylcarbazole) (PVK) host owing to high hole-affinity of the triphenylamine groups. The optoelectronic performances of phosphorescent EL devices, using P1-P6 as hosts and Ir(ppy)₃ as dopant (ITO/PEDOT:PSS/P1-P6:Ir(ppy)₃ (4 wt%):PBD (40 wt%)/BCP/Ca/Al), were greatly improved relative to that of PVK. The best performance was obtained with P4 device, in which the maximum luminance and luminance efficiency were 11?501 cd/m² and 10.6 cd/A, respectively.     

Synthesis and characterization of luminescent copolyethers with alternate stilbene derivatives and aromatic 1,3,4-oxadiazoles

New copoly(aryl ether)s containing alternate stilbene (P1), distyrylbenzene (P2), or distyrylstilbene (P3) chromophores and aromatic 1,3,4-oxadiazole were prepared by nucleophilic polycondensation. The copolyethers are basically amorphous materials with decomposition temperature greater than 250 °C. Introduction of side hexyloxy groups to distyrylbenzene chromophores in P2 significantly enhanced its solubility in common organic solvents such as toluene, THF, and chloroform. UV/visible and fluorescence spectrometers were employed to investigate their optical properties both in solution and in film state, whereas cyclic voltammograms were used to estimate their band diagrams. Photoluminescence maxima of P1, P2 and P3 are 442, 540 and 528 nm, respectively. Oxadiazole chromophores in backbone enhance electron affinity, whereas pendant hexyloxy groups decrease ionization potential. The threshold voltage and luminance of ITO/P2 (100 nm)/Al single layer device are 17 V and 950 cd/m², respectively.     

Synthesis of poly(1-β-naphthyl-2-phenylacetylene) membranes through desilylation and their properties

The polymerization of 1-β-naphthyl-2-[(p-trimethylsilyl)phenyl]acetylene (8a) with TaCl₅-n-Bu₄Sn in cyclohexane provided a high molecular weight polymer (9a) (M_w=3.4×10⁶). The corresponding monomers having p-dimethyl-t-butylsilyl and p-dimethyl(10-pinanyl)silyl groups in place of p-trimethylsilyl group in 8a also polymerized in a similar way to give high molecular weight polymers (9b, 9c, respectively; M_w>1×10⁶). All these polymers were soluble in many common solvents such as toluene and chloroform, and provided free-standing membranes by casting from toluene solution. The oxygen permeability coefficients (P_O2) of 9a at 25 °C was as high as 3500 barrers. The membrane of poly(1-β-naphthyl-2-phenylacetylene) (10a) was prepared by desilylation of the membrane of 9a with trifluoroacetic acid. Polymer 10a was insoluble in any solvents, and showed high thermal stability (the onset temperature of weight loss in air ∼470 °C). The P_O2 value of 10a reached 4300 barrers. Not only the membrane of 9c but also its desilylation product 10c exhibited large optical rotations ([α]_D=+2924 and +9800°, respectively) and strong CD signals. This indicates that the membrane of 10c maintains the helical main chain conformation of 9c with a large excess one-handed helix sense.     

Synthesis and properties of novel soluble polyimides having a spirobisindane-linked dianhydride unit

A new synthetic procedure was elaborated allowing the preparation of semiaromatic dianhydride. N-Methyl protected 4-chlorophthalic anhydride was nitrated with HNO₃ to produce N-methyl-4-chloro-5-nitrophthalimide (1). The aromatic nucleophilic substitution reaction between 5,5′,6,6′-tetrahydroxy-3,3,3′,3′-tetramethyl-1,1-spirobisindane and 1 afforded spirobisindane-linked bis(N-methylphthalimide) (2), which was hydrolyzed and subsequently dehydrated to give the corresponding dianhydride (3). The latter was polymerized with five different aromatic diamines to afford a series of aromatic polyimides. The properties of polyimides such as inherent viscosity, solubility, UV transparency and thermal stability were investigated to illustrate the contribution of the introduction of spirobisindane groups into the polyimide backbone. The resulting polyimides were readily soluble in polar solvents such as chloroform, THF and N-methyl-2-pyrrolidone. The glass-transition temperatures of these polyimides were in the range of 254-292 °C. The tensile strength, elongation at break, and Young's modulus of the polyimide film were 68.8-106.6 MPa, 5.9-9.8%, 1.7-2.0 GPa, respectively. The polymer films were colorless and transparent with the absorption cutoff wavelength at 286-308 nm.     

Synthesis and characterization of alternating fluorene-based copolymers containing diaryl- and non-substituted bithiophene units

A series of soluble alternating fluorene-based copolymers containing diaryl- and non-substituted bithiophene units are synthesized by palladium-catalyzed Suzuki coupling reaction. All polymers demonstrate green colors of photoluminescence (PL) in chloroform, good thermal stability (with decomposition temperatures above 436 °C), and high glass transition temperatures (in the range of 120-144 °C). Owing to the large steric hindrance of diaryl substituents on bithiophenes in the polymers (P2-P4), the aggregation of solids is reduced as well as the solubility is improved, so the performance of their PLED devices are superior to that of the non-substituted polymer (P1). Compared with P1, the introduction of substitutents at 3,3′-position of bithiophene in P2-P4 has significant effects on the photophysical properties of resulting polymers in solution and solid states. Though the PL quantum yield of P1 is much higher than those of diaryl-substituted polymers (P2-P4), the PLED device of P1 has the worst electroluminescence (EL) properties due to the poor solubility of P1. Consequently, among these polymers, the device made of P3 as an emitter has the highest luminance of 2590 cd/m² at 9.5 V. For optimum device performance, a device of P3 blended with PVK can be further enhanced to a brighter luminance of 4284 cd/m² at 18 V.     

Synthesis and properties of novel organosoluble polyimides derived from 1,4-bis[4-(3,4-dicarboxylphenoxy)]triptycene dianhydride and various aromatic diamines

A novel triptycene-based dianhydride, 1,4-bis[4-(3,4-dicarboxylphenoxy)]triptycene dianhydride, was prepared from 4-nitro-N-methylphthalimide and potassium phenolate of 1,4-dihydroxytriptycene (1). The aromatic nucleophilic substitution reaction between 4-nitro-N-methylphthalimide and 1 afforded triptycene-based bis(N-methylphthalimide) (2), which hydrolyzed and subsequently dehydrated to give the corresponding dianhydride (3). A series of new polyimides containing triptycene moieties were prepared from the dianhydride monomer (3) and various diamines in m-cresol via conventional one-step polycondensation method. Most of the resulting polyimides were soluble in common organic solvents, such as chloroform, THF, DMAc and DMSO. The polyimides exhibited excellent thermal and thermo-oxidative stabilities with the onset decomposition temperature and 10% weight loss temperature ranging from 448 to 486 °C and 526 to 565 °C in nitrogen atmosphere, respectively. The glass transition temperatures of the polyimides were in the range of 221-296 °C. The polyimide films were found to be transparent, flexible, and tough. The films had tensile strengths, elongations at break, and tensile moduli in the ranges 95-118 MPa, 5.3-16.2%, and 1.03-1.38 GPa, respectively. Wide-angle X-ray diffraction measurements revealed that these polyimides were amorphous.     

Synthesis and properties of organosoluble polyimides based on 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]cyclohexane

New aromatic diamine with cyclohexane cardo group substituted with trifluoromethyl group in the side chain, 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]cyclohexane (II), was prepared through the nucleophilic substitution reaction of 1,1-bis(4-hydroxyphenyl)cyclohexane and 2-chloro-5-nitrobenzotrifluoride in the presence of potassium carbonate, to yield the intermediate dinitro compound I, followed by catalytic reduction with hydrazine and Pd/C to afford the diamine II. Fluorinated polyimides (IVa-g) were prepared from the II with various aromatic dianhydrides via thermal or chemical imidization of poly(amic acid). These polyimides had inherent viscosity ranging from 0.72 to 1.16 dl/g and showed excellent solubility in a variety of organic solvents. They were soluble in a concentration of 10% in the amide polar solvent, and 1-5% in the other testing solvents. IV films showed good mechanical properties, excellent thermal stability. The 10% weight loss temperature was above 476 °C in nitrogen or air, and the glass transition temperature was recorded at 214-278 °C. In comparison of the IV series with the analogous nonfluorinated polyimides (V series) based on 1,1-bis[4-(4-aminophenoxy)phenyl]cyclohexane (II′), IV series revealed better solubility, lighter-colored and lower dielectric constants and moisture absorptions. Their films had cut-off wavelengths in the range of 364-414 nm, b^* value (a yellowness index) ranging from 3.3 to 66.3, dielectric constants of 3.02-3.55 (1 MHz), with moisture absorption of 0.16-0.36 wt%.     

Synthesis and characterization of chiral polythiophenes: Poly [(R)-(−) and (S)-(+)-2-(3′-thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate]

(R)-(−) (1) and (S)-(+)-2-(3′-Thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate (2) monomers were synthesized, characterized, and polymerized in chloroform using FeCl₃ as an oxidizing agent. Molecular weights of 2.6 × 10⁴ and 3.2 × 10⁴ for poly1 and poly2, respectively, were determined by SEC analysis. FTIR spectra of the polymers indicated the coupling of monomers through the α positions. UV-vis spectra showed absorption bands at λ_max = 226 and 423 nm for poly1 and poly2, ascribed to transitions of side groups and polythiophene backbone, respectively. Poly1 and poly2 remained stable up to 210 °C. At higher temperatures, a two step weight loss degradation process was observed for both polymers by TGA analysis. ¹H NMR, in the presence of Eu(tfc)₃, and optical rotation measurements indicate the chiral properties of the monomers 1 ([α]_D²⁸ = −76.2) and 2 ([α]_D²⁸ = +76.0), and the maintenance of chirality after polymerization (poly1 [α]_D²⁸ = −29.0 and poly2 [α]_D²⁸ = +28.4, c = 2.5 in THF). According to scanning electron microscopic analysis, the polymers are highly porous.     

A new class of high Tg and organosoluble polynaphthalimides

A new class of soluble six-membered ring polynaphthalimides (PNIs) was synthesized from asymmetrical fluorinated naphthalene-substituted monomers. All the resulting PNIs were easily soluble in many organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), dimethyl sulfoxide (DMSO), and chloroform. They also showed good thermal stability with glass transition temperature of 340-386 °C, 10% weight loss temperature in excess of 529 °C. Polyimide 3c could be solution-cast into tough and flexible film. The film had a tensile strength, elongation at break, and Young's modulus of about 117.6 MPa, 23.6%, and 1.77 GPa, respectively. The gas permeation property of the film of 3c was investigated with oxygen permeability coefficient (PO₂=3.99) and permeability selectivity coefficient of oxygen to nitrogen (PO₂/PN₂=5.27). Therefore, these materials are expected to be a good alternative to PIs based on five-membered rings with applications in gas separation membranes.     

Organo-soluble phosphinated polyimides from asymmetric diamines

Two new asymmetric diamines (1-2) were prepared via a facile, one-pot procedure. Based on diamine (1-2), a series of asymmetric polyimides (3-4) were prepared in NMP/xylene by high-temperature solution polymerization. The resulting polyimides are readily soluble in some organic solvents, and can be solution casted into flexible and creasable films. An intramolecular charge complex mechanism was proposed to the structure-optical transparency relationship. Polyimides 3-4 display high-Tg (319-401 °C), high moduli (2.40-7.20 GPa), moderate coefficient of thermal expansion (38-53 ppm/°C), and excellent flame retardancy. These results show that the introduction of the asymmetric structure is an effective way to improve organo-solubility while maintaining thermal properties. Because of these properties, polyimides 3-4 can be considered as excellent high-Tg and flame-retardant materials for microelectronic applications.