共查询到20条相似文献,搜索用时 140 毫秒
1.
方钢纵向磁化稳定状态的退磁场强度 总被引:2,自引:2,他引:0
根据方钢纵向磁化稳定状态下的磁荷分布规律(磁荷均布于各条棱线),给出了方钢内任意点退磁场强度的解析表达式和某些典型空间分布曲线,它们与磁化瞬间的对应曲线既有相似之处,也有不同特点,数值计算退磁场既有负值(传统意义的退磁场),也有正值(有效磁场大于磁化场)和零值(有效磁场与磁化场相等)。 相似文献
2.
3.
分析了浸液复合磁化探伤装置所产生的合成磁场,结论如下:它是个平面旋转磁场,故与受检工件侧面圆柱面同心的弧状裂纹用穿棒法是检查不出来的,而工件的退磁因子与复合磁化法中所用的磁化方式无关。 相似文献
4.
5.
6.
方钢纵向磁化的磁偶极子理论基础 总被引:10,自引:10,他引:0
本文从磁荷间的相互作用力和相互作用能出发,论证了长方体磁介质纵向磁化后磁荷将均匀地分布在所有各条棱线上,从而阐明了长方体纵向磁化后侧棱上出现非相关(杂乱)显示的原因。 相似文献
7.
方钢纵向磁化时各棱上的磁荷线密度 总被引:8,自引:8,他引:0
根据方钢纵向磁化原理(磁荷将均布于各条棱线上)和磁介质的磁化规律给出了方钢和带有矩形沟槽的方钢纵向磁化后各条棱线上的磁荷线密度近似解析表达式,并得出结论,工件表面沟槽深度与其引起漏磁场间的“直线律”关系仅是近似的。 相似文献
8.
9.
分析了浸液复合磁化探伤装置产生的合成磁场。结果表明,该合成磁场是个平面旋转磁场,故与受检工件侧面圆柱面同心的弧状裂纹无法用穿棒法检出,而工件的退磁因子与复合磁化法中所用的磁化方式无关。 相似文献
10.
11.
12.
Mitsuaki Katoh Noritaka Masumoto Kazumasa Nishio Tomiko Yamaguchi 《NDT & E International》2003,36(7):479-486
The yoke-magnetization is very popular in magnetic particle testing of welds. The detectability of a flaw by using this method largely depends on the magnetic flux density passing through a specimen to be examined or on the intensity of magnetic field acting in/on the specimen. In Japan inspectors have to check and confirm the appropriate magnetizing situation of the specimen by using an A-type standard test specimen specified in the standard JIS G 0565-1992. The development of indications by magnetic particles on the standard specimen is influenced by the air gap between the standard specimen and the specimen surface to be examined. Since the height and breadth of an artificial flaw in the standard specimen also influence the leakage of the magnetic flux density from the flaw, the information about the magnetizing situation is complex.In this paper we first identify influences of some factors on the magnetic leakage flux density from an artificial flaw in the standard specimen by using FEM modeling. Since the check with the standard specimen gives not a unique information to the magnetization state we investigate the technique, in which intensity of magnetic field acting on the specimen surface is used to characterize the magnetization. A finite element approach is applied to model the magnetization situation. The effectiveness of the modeling is confirmed by an experiment. 相似文献
13.
14.
15.
讨论了铁磁物质磁化的磁谱,得出了磁化的基本响应时间约为10^-8S。因此,磁粉探伤中,磁化的效果主要取决于励磁电流(50Hz)的峰值。 相似文献
16.
17.
根据穿棒法产生的磁场分布和磁介质的磁化规律,给出了圆盘边缘柱面上沟槽棱线上磁荷密度和漏磁场的解析表达式,计算了它们的数值并画出其空间分布图,理论分析与磁粉探伤的经典实验基础一致。 相似文献
18.
按照ASTME 1444标准进行荧光磁粉检验时,需要运用AS5282环验证磁粉检测系统性能,但标准中没有叙述如何调节电流,也未讨论AS5282环磁化后如何退磁。笔者通过长期实践,提出了用一根同样尺寸和材料的铜棒来预设磁化电流的方法。并在周向磁化AS5282环后再纵向磁化,然后再退磁的方法,解决AS5282环的剩磁问题。通过这两个步骤的实施,可以提高AS5282环对磁粉检测系统验证的可靠性,并进一步提高磁粉检测的有效性。 相似文献
19.
CJW-3000型专用磁粉探伤机出现了左右工位探伤灵敏度不一致的情况。经检查是由于一侧导电回路中的螺丝钢板间被渗入的磁悬液氧化,使电阻加大所致。据此提出了仔细保养设备、仔细观察磁化规范、设置磁化时间检测报警电路和放置灵敏度检测装置的四种解决方法,以提高探伤的可靠性。 相似文献
20.
磁粉探伤中的磁路分析 总被引:1,自引:1,他引:0
从磁路的角度分析了磁粉探伤中影响工作磁路的主要参数,结合便携式磁轭设备及复杂零件在旋转磁场中的磁化情况,具体讨论了影响试件磁化的因素及对这些因素的控制。 相似文献