首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
设计了一种高性能采样/保持(S/H)电路,采用全差分电容翻转型的主体结构,有效减小了噪声和功耗.在电路设计中,采用栅压自举开关,极大地减小了非线性失真,同时,有效地抑制了输入信号的直流偏移.采样/保持放大器电路采用折叠共源共栅结构,由于深亚微米工艺中器件本征增益减小,S/H电路为达到更高增益,采用增益提升技术.设计的采样/保持电路采用0.18μm1P5M工艺实现,在1.8V电源电压、125 MHz采样速率下,输出差动摆幅达到2 V(VP-P),输入信号到奈奎斯特频率时仍能达到98 dB以上的无杂散动态范围(SFDR),其性能满足14位精度、125MHz转换速率的流水线ADC要求.  相似文献   

2.
设计了一种高性能的采样保持(S/H)电路,在1.8V的电源电压下,其性能满足12位精度、100MS/s转换速率的ADC的要求。设计中采用了一种新型的自举采样开关,提高了S/H电路的可靠性和线性度;对于高增益大带宽的运算跨导放大器OTA的带宽设计,在分析了主运放和辅助运放在带宽和相位裕度等方面的关系的基础上,提出了新的设计方法。仿真结果表明:S/H电路的差动输出摆幅达到了2V;对于输入为49MHz的正弦波,测得其信号噪声失真比达到了82dB,满足12位ADC的要求;整个电路的功耗约为20mW。  相似文献   

3.
陈俊龙  黄继伟  胡炜  吴嘉士  张荣晶  张千文 《微电子学》2015,45(5):564-567, 572
设计了一种应用于流水线型模数转换器的14位100 MHz采样保持电路,并在电路设计中,提出了一种改进型的栅压自举采样开关电路。在不增加电路复杂性的情况下,栅压自举采样开关电路可以有效地增加采样开关管的开启时间和关断时间,以及电路的可靠性。采样保持电路采用电容翻转式结构,以及采用增益提高的全差分折叠式共源共栅跨导放大器来实现。采用SMIC 1.8 V/3.3 V 0.18 μm 1P6M CMOS工艺对电路进行设计与仿真。仿真结果显示,在10.009765 MHz输入信号,100 MHz工作频率下,输出信号的无杂散动态范围(SFDR)为95.9 dB,与传统自举开关相比,提高了16.3 dB。  相似文献   

4.
尹文婧  叶凡  许俊  李联 《微电子学》2006,36(6):789-793
设计了一种可用于欠采样情况的高精度、低功耗采样/保持电路。在40 MHz时钟频率下,采样90 MHz输入信号时可达11位以上精度。采用电容翻转结构的采样/保持电路,以消除电容失配的影响;使用栅压自举开关,以提高线性度,实现欠采样输入;并设计了一种高增益、大带宽、低功耗的增益自举套筒式共源共栅(telescopic cascode)运算放大器。电路采用SMIC 0.35μmCMOS工艺实现,电源电压为3.3 V,功耗仅为7.6 mW。  相似文献   

5.
提出了一种两倍增益高线性、高速、高精度采样/保持电路。该采样/保持电路通过对输入信号实现两倍放大,改善了高频非线性失真;一种新型的消除衬底偏置效应的采样开关,有效地提高了采样的线性度;高增益和宽带宽的折叠共源共栅运算放大器保证了采样/保持电路的精度和速度。整个电路以0.35μm AMS Si CMOS模型库验证。模拟结果显示,在输入信号为49.21875MHz正弦波,采样频率为100 MHz时,增益误差为70.9μV,SFDR可达到84.5 dB。  相似文献   

6.
设计了一种用于流水线型A/D转换器的10位160 MS/s CMOS采样保持器.电路采用电容翻转式结构,以及运用增益提高技术(gain-boosting)的折叠式共源共栅放大器,以满足高速、高精度的要求;优化采样电容和运算放大器指标,以保证噪声容限和线性指标;优化辅助运放,从而保证运放的稳定性.HSPICE仿真结果表明,在78.83 MHz输入信号、160.34 MHz工作频率下,输出信号的无杂散动态范围为77.3 dB.  相似文献   

7.
提出了基于TSMC 0.35μm锗硅(SiGe)BiCMOS工艺的全差分跨导运算放大器(OTA),充分利用了异质结晶体管(HBT)共射共基结构的大跨导、小寄生效应、低噪声等特性.采用共源共栅以及增益倍增技术的负载管,在3.3V单电源下,开环增益为92.2dB,单位增益频率为1.26GHz,相位裕度为61.1o(负载为550fF时),差分输出摆幅为3V,以此OTA为核心的采样保持放大器(SHA)的最大采样频率为125MHz.  相似文献   

8.
一种用于流水线A/D转换器的低功耗采样/保持电路   总被引:1,自引:0,他引:1  
陈曦  何乐年 《微电子学》2005,35(5):545-548
文章介绍了一种适用于10位20MS/s流水线A/D转换器的采样/保持(S/H)电路。该电路为开关电容结构,以0.6μm DPDM CMOS工艺实现。采用差分信号输入结构,降低对共模噪声的敏感度,共模反馈电路的设计稳定了共模输出,以达到高精度。该S/H电路采用低功耗运算跨导放大器(OTA),在5V电源电压下,功耗仅为5mW。基于该S/H电路的流水线A/D转换器在20MHz采样率下,信噪比(SNR)为58dB,功耗为49mW。  相似文献   

9.
通过采样保持电路中运放的复用,提出了一种具有高线性度MOS采样开关的模数转换器前端采样保持电路结构。这种结构可以显著降低采样开关导通电阻变化引入的非线性,从而在不增加开关面积和功耗的情况下,实现了高性能的采样保持电路。基于0.13?m的标准CMOS工艺,对提出的采样保持电路进行了仿真。在采样时钟频率为100MHz,输入信号频率1MHz时,仿真结果显示,无杂散动态范围(SFDR)达到了116.6dB,总谐波失真(THD)达到了112.7dB,信号谐波噪声比(SNDR)达到103.7dB,可以满足14比特流水线ADC对采样保持电路的要求。  相似文献   

10.
一种57.6mW,10位,50MS/s流水线操作CMOS A/D转换器   总被引:6,自引:0,他引:6  
在1.8V,0.18μm CMOS工艺下,实现了10位,50MS/s流水线操作A/D转换器的设计和测试.通过优化采样电容和运算跨导放大器(OTA)电流,并采用动态比较器,从而降低功耗;采用复位结构的采样/保持和余量增益电路消除OTA失调电压的影响;优化OTA的次极点,保证其工作稳定.测试结果表明:ADC在整个量化范围内无失码,功耗为57.6mW,失调电压为0.8mV,微分非线性为-0.6~0.7LSB.对5.1MHz的输入信号量化,可获得44.9dB的信号与噪声及谐波失真比.电路面积为0.52mm2.  相似文献   

11.
DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.  相似文献   

12.
From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.  相似文献   

13.
The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.  相似文献   

14.
The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.  相似文献   

15.
Today, micro-system technology and the development of new MEMS (Micro-Electro-Mechanical Systems) are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.  相似文献   

16.
Waveguide multilayer optical card (WMOC) is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling & processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic (VB) language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.  相似文献   

17.
This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel's.  相似文献   

18.
The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.  相似文献   

19.
Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.  相似文献   

20.
An insert layer structure organic electroluminescent device(OLED) based on a new luminescent material (Zn(salen)) is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn(salen)/Liq/LiF/A1/CuPc/NPD/Zn(salen)/Liq/LiF/A1. Effective insert electrode layers comprising LiF(1nm)/Al(5 nm) are used as a single semitransparent mirror, and bilayer cathode LiF(1 nm)/A1(100 nm) is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号