Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation catalyst) and from a vehicle fueled with low-sulfur diesel fuel (equipped with DPF) were lower than from the low-sulfur diesel fueled vehicle equipped with OC. All vehicle configurations had generally lower emissions of toxics than an uncontrolled diesel engine. Tunnel backgrounds (measurements without the vehicle running) were measured throughout this study and were helpful in determining the incremental increase in pollutant emissions. Also, the on-site determination of VOCs, especially 1,3-butadiene, helped minimize measurement losses due to sample degradation after collection.     

Characteristics of SME biodiesel-fueled diesel particle emissions and the kinetics of oxidation

Biodiesel is one of the most promising alternative diesel fuels. As diesel emission regulations have become more stringent, the diesel particulate filter (DPF) has become an essential part of the aftertreatment system. Knowledge of kinetics of exhaust particle oxidation for alternative diesel fuels is useful in estimating the change in regeneration behavior of a DPF with such fuels. This study examines the characteristics of diesel particulate emissions as well as kinetics of particle oxidation using a 1996 John Deere T04045TF250 off-highway engine and 100% soy methyl ester (SME) biodiesel (B100) as fuel. Compared to standard D2 fuel, this B100 reduced particle size, number, and volume in the accumulation mode where most of the particle mass is found. At 75% load, number decreased by 38%, DGN decreased from 80 to 62 nm, and volume decreased by 82%. Part of this decrease is likely associated with the fact that the particles were more easily oxidized. Arrhenius parameters for the biodiesel fuel showed a 2-3times greater frequency factor and approximately 6 times higher oxidation rate compared to regular diesel fuel in the range of 700-825 degrees C. The faster oxidation kinetics should facilitate regeneration when used with a DPF.     

Comparative analysis on the effects of diesel particulate filter and selective catalytic reduction systems on a wide spectrum of chemical species emissions

Two methods, diesel particulate filter (DPF) and selective catalytic reduction (SCR) systems,for controlling diesel emissions have become widely used, either independently or together, for meeting increasingly stringent emissions regulations worldwide. Each of these systems is designed for the reduction of primary pollutant emissions including particulate matter (PM) for DPF and nitrogen oxides (NOx) for SCR. However, there have been growing concerns regarding the secondary reactions that these aftertreatment systems may promote, involving unregulated species emissions. This study was performed to gain an understanding of the effects that these aftertreatment systems may have on the emission levels of a wide spectrum of chemical species found in diesel engine exhaust. Samples were extracted using a source dilution sampling system designed to collect exhaust samples representative of real-world emissions. Testing was conducted on a heavy-duty diesel engine with no aftertreatment devices to establish a baseline measurement and also on the same engine equipped first with a DPF system and then a SCR system. Each of the samples was analyzed for a wide variety of chemical species, including elemental and organic carbon, metals, ions, n-alkanes, aldehydes, and polycyclic aromatic hydrocarbons, in addition to the primary pollutants, due to the potential risks they pose to the environment and public health. The results show that the DPF and SCR systems were capable of substantially reducing PM and NOx emissions, respectively. Further, each of the systems significantly reduced the emission levels of the unregulated chemical species, while the notable formation of new chemical species was not observed. It is expected that a combination of the two systems in some future engine applications would reduce both primary and secondary emissions significantly.     

The effects of the catalytic converter and fuel sulfur level on motor vehicle particulate matter emissions: gasoline vehicles

Scanning mobility and electrical low-pressure impactor particle size measurements conducted during chassis dynamometer testing reveal that neither the catalytic converter nor the fuel sulfur content has a significant effect on gasoline vehicle tailpipe particulate matter (PM) emissions. For current technology, port fuel injection, gasoline engines, particle number emissions are < or = 2 times higher from vehicles equipped with blank monoliths as compared to active catalysts, insignificant in contrast to the 90+% removal of hydrocarbons. PM mass emission rates derived from the size distributions are equal within the experimental uncertainty of 50-100%. Gravimetric measurements exhibit a 3-10-fold PM mass increase when the active catalyst is omitted, which is attributed to gaseous hydrocarbons adsorbing onto the filter medium. Both particle number and gravimetric measurements show that gasoline vehicle tailpipe PM emissions are independent (within 2 mg/mi) of fuel sulfur content over the 30-990 ppm concentration range. Nuclei mode sulfate aerosol is not observed in either test cell measurements or during wind tunnel testing. For three-way catalyst equipped vehicles, the principal sulfur emission is SO2; however a sulfur balance is not obtained over the drive cycle. Instead, sulfur is stored on the catalyst during moderate driving and then partially removed during high speed/load operation.     

Time-resolved characterization of diesel particulate emissions. 2. Instruments for elemental and organic carbon measurements

The measurement of elemental carbon (EC) and organic carbon (OC) mass for particles emitted by diesel vehicles is currently accomplished using particle collection on filters, followed by analysis using the thermal/optical reflectance carbon analysis method (TOR) or one of its variations. Such filter methods limit time resolution to a minimum of several minutes, making it impossible to study emissions during transient operating conditions. Testing of five different measurement methods has demonstrated that fast response measurement of diesel exhaust particulate EC and OC concentrations, consistent with TOR filter measurements, is feasible using existing technology. EC mass concentrations are best measured through determination of particulate light absorption with a photoacoustic instrument or determination of light extinction with a smoke meter. The photoacoustic instrument has the better dynamic range and sensitivity, whereas the smoke meter is a simpler instrument. Fast response OC measurements cannot be made with any single instrument tested. However, a combination of real time weighing as implemented in the tapered element oscillating microbalance with the photoacoustic instrument has been shown to be capable of determining OC concentrations with good time response. The addition of a nephelometer to the OC measurement could potentially improve time resolution, freedom from interferences, and sensitivity.     

Ultrafine PM emissions from natural gas,oxidation-catalyst diesel,and particle-trap diesel heavy-duty transit buses

This paper addresses how current technologies effective for reducing PM emissions of heavy-duty engines may affect the physical characteristics of the particles emitted. Three in-use transit bus configurations were compared in terms of submicron particle size distributions using simultaneous SMPS measurements under two dilution conditions, a minidiluter and the legislated constant volume sampler (CVS). The compressed natural gas (CNG)-fueled and diesel particulate filter (DPF)-equipped diesel configurations are two "green" alternatives to conventional diesel engines. The CNG bus in this study did not have an oxidation catalyst whereas the diesel configurations (with and without particulate filter) employed catalysts. The DPF was a continuously regenerating trap (CRT). Particle size distributions were collected between 6 and 237 nm using 2-minute SMPS scans during idle and 55 mph steady-state cruise operation. Average particle size distributions collected during idle operation of the diesel baseline bus operating on ultralow sulfur fuel showed evidence for nanoparticle growth under CVS dilution conditions relative to the minidiluter. The CRT effectively reduced both accumulation and nuclei mode concentrations by factors of 10-100 except under CVS dilution conditions where nuclei mode concentrations were measured during 55 mph steady-state cruise that exceeded baseline diesel concentrations. The CVS data suggest some variability in trap performance. The CNG bus had accumulation mode concentrations 10-100x lower than the diesel baseline but often displayed large nuclei modes, especially under CVS dilution conditions. Partly this may be explained by the lack of an oxidation catalyst on the CNG, but differences between the minidiluter and CVS size distributions suggest that dilution ratio, temperature-related wall interactions, and differences in tunnel background between the diluters contributed to creating nanoparticle concentrations that sometimes exceeded diesel baseline concentrations when driving under load. The results do not support use of CVS dilution methodology for ultrafine particle sampling, and, despite attention to collection of tunnel blanks in this study, results indicate that a protocol needs to be determined and prescribed for taking into account tunnel blank "emissions" to obtain meaningful comparisons between different technologies. Of critical importance is determining how temperature differences between tunnel blank and test cycle sampling compare in terms of background particle numbers. Total particle number concentrations for the minidiluter sampling point were not significantly different for the two alternative technologies when considering all the steady-cycle data collected. Concentrations ranged from 0.8 to 3 x 10(6) for the baseline bus operating on ultralow sulfur fuel, from 0.5 to 9 x 10(4) for the diesel bus equipped with the CRT filter, and from 1 to 8 x 10(4) particles/cc for the CNG bus.     

Uncertainty in particle number modal analysis during transient operation of compressed natural gas, diesel, and trap-equipped diesel transit buses

The relationships between transient vehicle operation and ultrafine particle emissions are not well-known, especially for low-emission alternative bus technologies such as compressed natural gas (CNG) and diesel buses equipped with particulate filters/traps (TRAP). In this study, real-time particle number concentrations measured on a nominal 5 s average basis using an electrical low pressure impactor (ELPI) for these two bus technologies are compared to that of a baseline catalyst-equipped diesel bus operated on ultralow sulfur fuel (BASE) using dynamometer testing. Particle emissions were consistently 2 orders of magnitude lower for the CNG and TRAP compared to BASE on all driving cycles. Time-resolved total particle numbers were examined in terms of sampling factors identified as affecting the ability of ELPI to quantify the particulate matter number emissions for low-emitting vehicles such as CNG and TRAP as a function of vehicle driving mode. Key factors were instrument sensitivity and dilution ratio, alignment of particle and vehicle operating data, sampling train background particles, and cycle-to-cycle variability due to vehicle, engine, after-treatment, or driver behavior. In-cycle variability on the central business district (CBD) cycle was highest for the TRAP configuration, but this could not be attributed to the ELPI sensitivity issues observed for TRAP-IDLE measurements. Elevated TRAP emissions coincided with low exhaust temperature, suggesting on-road real-world particulate filter performance can be evaluated by monitoring exhaust temperature. Nonunique particle emission maps indicate that measures other than vehicle speed and acceleration are necessary to model disaggregated real-time particle emissions. Further testing on a wide variety of test cycles is needed to evaluate the relative importance of the time history of vehicle operation and the hysteresis of the sampling train/dilution tunnel on ultrafine particle emissions. Future studies should monitor particle emissions with high-resolution real-time instruments and account for the operating regime of the vehicle using time-series analysis to develop predictive number emissions models.     

Comparison of mass-based and non-mass-based particle measurement systems for ultra-low emissions from automotive sources

Drastic reduction in particle emissions of diesel-powered vehicles and new findings on the health impact of particles raise the question of a more sensitive measurement procedure. In this paper, 16 different particle mass measurement systems are compared on a diesel heavy-duty engine equipped with a particle filter to investigate their feasibility for particle characterization for future ultra-low concentration levels. The group of instruments comprises mass-related methods (filter methods, laser-induced incandescence, photoacoustic detection, photoelectric charging, combined inertial and mobility sizing, opacity) as well as non-mass-related methods (CPC, diffusion battery, diffusion charger, ELPI, light scattering). The instruments are compared on the basis of repeatability, limit of detection, sensitivity, time resolution and correlation with the regulated gravimetric filter method, and elemental carbon fraction (EC). Several time-resolved methods show good performance and give reliable results. Opacimeters and light scattering, however, reveal shortcomings at these low concentrations. For all time-resolved advanced methods, poor correlation with the regulated filter method is observed, but most of them show good correlation with the EC fraction of the particles. This outcome demonstrates the crucial role of the sampling conditions for measurement methods that do not exclude volatile material from detection. A clear improvement in sensitivity is observed when non-mass-based instruments are applied (e.g., number or surface-related methods). The results reveal that reliable measurement methods exist for future measurement procedures. However, a change in the measurement method will lead to a discontinuity in the inventories, making it difficult to compare the particle emissions from future and past vehicle generations.     

Diesel particle filter and fuel effects on heavy-duty diesel engine emissions

The impacts of biodiesel and a continuously regenerated (catalyzed) diesel particle filter (DPF) on the emissions of volatile unburned hydrocarbons, carbonyls, and particle associated polycyclic aromatic hydrocarbons (PAH) and nitro-PAH, were investigated. Experiments were conducted on a 5.9 L Cummins ISB, heavy-duty diesel engine using certification ultra-low-sulfur diesel (ULSD, S ≤ 15 ppm), soy biodiesel (B100), and a 20% blend thereof (B20). Against the ULSD baseline, B20 and B100 reduced engine-out emissions of measured unburned volatile hydrocarbons and PM associated PAH and nitro-PAH by significant percentages (40% or more for B20 and higher percentage for B100). However, emissions of benzene were unaffected by the presence of biodiesel and emissions of naphthalene actually increased for B100. This suggests that the unsaturated FAME in soy-biodiesel can react to form aromatic rings in the diesel combustion environment. Methyl acrylate and methyl 3-butanoate were observed as significant species in the exhaust for B20 and B100 and may serve as markers of the presence of biodiesel in the fuel. The DPF was highly effective at converting gaseous hydrocarbons and PM associated PAH and total nitro-PAH. However, conversion of 1-nitropyrene by the DPF was less than 50% for all fuels. Blending of biodiesel caused a slight reduction in engine-out emissions of acrolein, but otherwise had little effect on carbonyl emissions. The DPF was highly effective for conversion of carbonyls, with the exception of formaldehyde. Formaldehyde emissions were increased by the DPF for ULSD and B20.     

Reduction of particulate matter emissions from diesel backup generators equipped with four different exhaust aftertreatment devices

Diesel particulate matter (PM) reduction efficiencies for backup generators (BUGs) (> 300 kW) equipped with a diesel oxidation catalyst (DOC), DOC+fuel-borne catalyst additive combination (DOC+FBC), passive diesel particulate filter (DPF), and an active DPF were measured. Overall, the DOC and DOC+FBC technologies were found to be effective in reducing mainly organic carbon (OC) emissions (56-77%) while both DPFs showed excellent performance in reducing both elemental carbon (EC) and OC emissions (> 90%). These findings demonstrate the potential for applying DOCs to older engines where PM is dominated by the OC fraction. In most modern engine applications, where the PM consists of mainly EC, the DOC will be largely ineffective. Alternatively, passive and active DPFs are expected to be efficient for most engine technologies. Measurements of particle size distributions provided evidence of the high temperature formation of sulfate nanoparticles across the control technologies despite the use of ultralow sulfur diesel. Changes in the particle size distribution and the organic fraction of PM indicate that the OC component of PM is primarily found in the smaller sized particles.     

Apportionment of motor vehicle emissions from fast changes in number concentration and chemical composition of ultrafine particles near a roadway intersection

High frequency spikes in ultrafine number concentration near a roadway intersection arise from motor vehicles that accelerate after a red light turns green. The present work describes a method to determine the contribution of motor vehicles to the total ambient ultrafine particle mass by correlating these number concentration spikes with fast changes in ultrafine particle chemical composition measured with the nano aerosol mass spectrometer, NAMS. Measurements were performed at an urban air quality monitoring site in Wilmington, Delaware during the summer and winter of 2009. Motor vehicles were found to contribute 48% of the ultrafine particle mass in the winter measurement period, but only 16% of the ultrafine particle mass in the summer period. Chemical composition profiles and contributions to the ultrafine particle mass of spark vs diesel vehicles were estimated by correlating still camera images, chemical composition and spike contribution at each time interval.. The spark and diesel contributions were roughly equal, but the uncertainty in the split was large. The distribution of emissions from individual vehicles was determined by correlating camera images with the spike contribution to particle number concentration at each time interval. A small percentage of motor vehicles were found to emit a disproportionally large concentration of ultrafine particles, and these high emitters included both spark ignition and diesel vehicles.     

Comparison of methods for online measurement of diesel particulate matter

Gravimetric analysis is the regulatory method for diesel particulate mass measurement. Because of issues such as adsorption/volatilization artifacts, it faces obstacles in measuring ultra low level emissions from modern diesel engines. Alternative methods of suspended particle mass measurement have been developed that show improvements in time resolution, sensitivity, and accuracy. Three size-resolved methods were considered here. Two methods rely on converting number size distributions obtained using a scanning mobility particle sizer (SMPS). Conversion techniques were based on effective density measurements and the Lall-Friedlander aggregate model. The third method employs the Universal Nanoparticle Analyzer (UNPA) to measure the aggregate size distribution from which mass is calculated. Results were compared with mass concentrations obtained using gravimetric analysis. The effective density conversion resulted in mass concentrations that were highly correlated (R(2) >0.99) with filter mass. The ratios to filter mass concentration were found to be 0.99 ± 0.04, 0.45 ± 0.03, and 0.45 ± 0.19 for the effective density conversion, the Lall-Friedlander conversion, and the UNPA, respectively, for a wide range of engine operating conditions. In addition, the diesel aerosol mass distributions measured by the online techniques are in agreement to within 15-20% with respect to the mass median diameter, while discrepancies were observed in the mass concentration.     

Influence of real-world engine load conditions on nanoparticle emissions from a DPF and SCR equipped heavy-duty diesel engine

The experiments aimed at investigating the effect of real-world engine load conditions on nanoparticle emissions from a Diesel Particulate Filter and Selective Catalytic Reduction after-treatment system (DPF-SCR) equipped heavy-duty diesel engine. The results showed the emission of nucleation mode particles in the size range of 6-15 nm at conditions with high exhaust temperatures. A direct result of higher exhaust temperatures (over 380 °C) contributing to higher concentration of nucleation mode nanoparticles is presented in this study. The action of an SCR catalyst with urea injection was found to increase the particle number count by over an order of magnitude in comparison to DPF out particle concentrations. Engine operations resulting in exhaust temperatures below 380 °C did not contribute to significant nucleation mode nanoparticle concentrations. The study further suggests the fact that SCR-equipped engines operating within the Not-To-Exceed (NTE) zone over a critical exhaust temperature and under favorable ambient dilution conditions could contribute to high nanoparticle concentrations to the environment. Also, some of the high temperature modes resulted in DPF out accumulation mode (between 50 and 200 nm) particle concentrations an order of magnitude greater than typical background PM concentrations. This leads to the conclusion that sustained NTE operation could trigger high temperature passive regeneration which in turn would result in lower filtration efficiencies of the DPF that further contributes to the increased solid fraction of the PM number count.     

Measurements of particle number and mass concentrations and size distributions in a tunnel environment

Particulate matter emissions were measured in two bores of the Caldecott Tunnel in Northern California during August and September 2004. One bore (Bore 1) is open to both heavy- and light-duty vehicles while heavy-duty vehicles are prohibited from entering the second bore (Bore 2). Particulate matter number and mass size distributions, chemical composition, and gaseous copollutants were recorded for four consecutive days near the entrance and exit of each bore. Size-resolved emission factors were determined for particle number, particle mass, elemental carbon, organic carbon (OC), sulfate, nitrate, and selected elements. The size distributions in both the bores showed a single large mode at roughly 15-20 nm in mobility diameter, with occasional smaller modes around 100 nm. The PM10 mass emission factor for heavy-duty vehicles was 14.5 times higher than that of light-duty vehicles. The particles derived from diesel are more abundant in elemental carbon, 70.9% of PM10 emissions, as compared to the light-duty vehicles. Conversely, a greater percentage of OC was found in light-duty emissions than heavy-duty emissions. In comparison to previous studies at the Caldecott Tunnel, less particle mass but more particle numbers are emitted by vehicles than was the case 7 years ago.     

Effects of dilution on fine particle mass and partitioning of semivolatile organics in diesel exhaust and wood smoke

Experiments were conducted to examine the effects of dilution on fine particle mass emissions from a diesel engine and wood stove. Filter measurements were made simultaneously using three dilution sampling systems operating at dilution ratios ranging from 20:1 to 510:1. Denuders and backup filters were used to quantify organic sampling artifacts. For the diesel engine operating at low load and wood combustion, large decreases in fine particle mass emissions were observed with increases in dilution. For example, the PM2.5 mass emission rate from a diesel engine operating at low load decreased by 50% when the dilution ratio was increased from 20:1 to 350:1. Measurements of organic and elemental carbon indicate that the changes in fine particle mass with dilution are caused by changes in partitioning of semivolatile organic compounds. At low levels of dilution semivolatile species largely occur in the particle phase, but increasing dilution reduces the concentration of semivolatile species, shifting this material to the gas phase in order to maintain phase equilibrium. Emissions of elemental carbon do not vary with dilution. Organic sampling artifacts are shown to vary with dilution because of the combination of changes in partitioning coupled with adsorption of gas-phase organics by quartz filters. The fine particle mass emissions from the diesel engine operating at medium load did not vary with dilution because of the lower emissions of semivolatile material and higher emissions of elemental carbon. To measure partitioning of semivolatile materials under atmospheric conditions, partitioning theory indicates that dilution samplers need to be operated such that the diluted exhaust achieves atmospheric levels of dilution. Too little dilution can potentially overestimate the fine particle mass emissions, and too much dilution (with clean air) can underestimate them.     

Evaluation of the Impacts of Biodiesel and Second Generation Biofuels on NO(x) Emissions for CARB Diesel Fuels

The impact of biodiesel and second generation biofuels on nitrogen oxides (NO(x)) emissions from heavy-duty engines was investigated using a California Air Resources Board (CARB) certified diesel fuel. Two heavy-duty engines, a 2006 engine with no exhaust aftertreatment, and a 2007 engine with a diesel particle filter (DPF), were tested on an engine dynamometer over four different test cycles. Emissions from soy- and animal-based biodiesels, a hydrotreated renewable diesel, and a gas to liquid (GTL) fuel were evaluated at blend levels from 5 to 100%. NO(x) emissions consistently increased with increasing biodiesel blend level, while increasing renewable diesel and GTL blends showed NO(x) emissions reductions with blend level. NO(x) increases ranged from 1.5% to 6.9% for B20, 6.4% to 18.2% for B50, and 14.1% to 47.1% for B100. The soy-biodiesel showed higher NO(x) emissions increases compared to the animal-biodiesel. NO(x) emissions neutrality with the CARB diesel was achieved by blending GTL or renewable diesel fuels with various levels of biodiesel or by using di-tert-butyl peroxide (DTBP). It appears that the impact of biodiesel on NO(x) emissions might be a more important consideration when blended with CARB diesel or similar fuels, and that some form of NO(x) mitigation might be needed for biodiesel blends with such fuels.     

Effect of diesel oxidation catalysts on the diesel particulate filter regeneration process

A Diesel Particulate Filter (DPF) regeneration process was investigated during aftertreatment exhaust of a simulated diesel engine under the influence of a Diesel Oxidation Catalyst (DOC). Aerosol mass spectrometry analysis showed that the presence of the DOC decreases the Organic Carbon (OC) fraction adsorbed to soot particles. The activation energy values determined for soot nanoparticles oxidation were 97 ± 5 and 101 ± 8 kJ mol(-1) with and without the DOC, respectively; suggesting that the DOC does not facilitate elementary carbon oxidation. The minimum temperature necessary for DPF regeneration was strongly affected by the presence of the DOC in the aftertreatment. The conversion of NO to NO(2) inside the DOC induced the DPF regeneration process at a lower temperature than O(2) (ΔT = 30 K). Also, it was verified that the OC fraction, which decreases in the presence of the DOC, plays an important role to ignite soot combustion.     

Time resolved characterization of diesel particulate emissions. 1. Instruments for particle mass measurements

The measurement of diesel vehicle exhaust particulate mass is currently accomplished using filter collection methods according to the Code of Federal Regulations (CFR). Such filter methods limit time resolution to a minimum of several minutes, making it impossible to study emissions during transient operating conditions. Extensive testing of five different measurement methods has demonstrated that fast response measurements of diesel exhaust particulate mass concentrations, consistent with CFR filter measurements, are feasible using existing technology. The measurement principles of choice are the real time weighing of exhaust samples as implemented in the tapered element oscillating microbalance (TEOM) and the measurement of light scattering from exhaust particles as implemented in the DustTrak nephelometer. Each of these two instruments has distinctive strengths. The TEOM excels in the area of constant calibration, independent of vehicle. For the DustTrak, this calibration varies by vehicle. On the other hand, the DustTrak has an excellent signal-to-noise ratio, freedom from interference due to other exhaust sample properties, good time resolution, and simplicity. The strengths of the two measurement methods are complimentary, so an obvious suggestion is to integrate them. The nephelometer would obtain a fast response signal, with near real time calibration provided by the microbalance.     

Effect of water/fuel emulsions and a cerium-based combustion improver additive on HD and LD diesel exhaust emissions

One of the major technological challenges for the transport sector is to cut emissions of particulate matter (PM) and nitrogen oxides (NOx) simultaneously from diesel vehicles to meet future emission standards and to reduce their contribution to the pollution of ambient air. Installation of particle filters in all existing diesel vehicles (for new vehicles, the feasibility is proven) is an efficient but expensive and complicated solution; thus other short-term alternatives have been proposed. It is well known that water/diesel (W/ D) emulsions with up to 20% water can reduce PM and NOx emissions in heavy-duty (HD) engines. The amount of water that can be used in emulsions for the technically more susceptible light-duty (LD) vehicles is much lower, due to risks of impairing engine performance and durability. The present study investigates the potential emission reductions of an experimental 6% W/D emulsion with EURO-3 LD diesel vehicles in comparison to a commercial 12% W/D emulsion with a EURO-3 HD engine and to a Cerium-based combustion improver additive. For PM, the emulsions reduced the emissions with -32% for LD vehicles (mass/km) and -59% for the HD engine (mass/ kWh). However, NOx emissions remained unchanged, and emissions of other pollutants were actually increased forthe LD vehicles with +26% for hydrocarbons (HC), +18% for CO, and +25% for PM-associated benzo[a]pyrene toxicity equivalents (TEQ). In contrast, CO (-32%), TEQ (-14%), and NOx (-6%) were reduced by the emulsion for the HD engine, and only hydrocarbons were slightly increased (+16%). Whereas the Cerium-based additive was inefficient in the HD engine for all emissions except for TEQ (-39%), it markedly reduced all emissions for the LD vehicles (PM -13%, CO -18%, HC -26%, TEQ -25%) except for NOx, which remained unchanged. The presented data indicate a strong potential for reductions in PM emissions from current diesel engines by optimizing the fuel composition.     

Effect of advanced aftertreatment for PM and NOx reduction on heavy-duty diesel engine ultrafine particle emissions

Four heavy-duty and medium-duty diesel vehicles were tested in six different aftertreament configurations using a chassis dynamometer to characterize the occurrence of nucleation (the conversion of exhaust gases to particles upon dilution). The aftertreatment included four different diesel particulate filters and two selective catalytic reduction (SCR) devices. All DPFs reduced the emissions of solid particles by several orders of magnitude, but in certain cases the occurrence of a volatile nucleation mode could increase total particle number emissions. The occurrence of a nucleation mode could be predicted based on the level of catalyst in the aftertreatment, the prevailing temperature in the aftertreatment, and the age of the aftertreatment. The particles measured during nucleation had a high fraction of sulfate, up to 62% of reconstructed mass. Additionally the catalyst reduced the toxicity measured in chemical and cellular assays suggesting a pathway for an inverse correlation between particle number and toxicity. The results have implications for exposure to and toxicity of diesel PM.