Intermetallic compounds and adhesion strength between the Sn-9Zn-1.5Ag-0.5Bi lead-free solder and unfluxed Cu substrate

The intermetallic compounds (IMCs) formed at the interface between the Sn-9Zn-1.5Ag-0.5Bi lead-free solder alloy and unfluxed Cu substrate have been investigated by x-ray diffraction, optical microscopy, scanning electron microscopy (SEM), and energy-dispersive spectrometry (EDS). The melting point and melting range of the Sn-9Zn-1.5Ag-0.5Bi solder alloy are determined as 195.9°C and 10°C, respectively, by differential scanning calorimetry (DSC). Cu₆Sn₅ and Cu₅Zn₈ IMCs are formed between the Sn-9Zn-1.5Ag-0.5Bi/unfluxed Cu substrate wetted at 250°C for 10 sec. The interfacial adhesion strength changes from 10.27±0.68 MPa to 8.58±0.59 MPa when soldering time varies from 10 sec to 30 sec at 250°C.     

Reliability of adhesion strength of the Sn-9Zn-1.5Ag-0.5Bi/Cu during isothermal aging

The reliability of adhesion strength of the Sn-9Zn-1.5Ag-0.5Bi/Cu during isothermal aging has been investigated. Due to the growth and decomposition of the intermetallic compound (IMC), the adhesion strength varies with aging at 150°C from 100, 400, and 700–1,000 h as wetted at 250°C for 60 sec. The IMC layers are determined at the Sn-9Zn-1.5Ag-0.5Bi/Cu interface by an x-ray diffractometer (XRD), an optical microscope (OM), a scanning electron microscope (SEM), an energy-dispersive spectroscope (EDS), and a transmission electron microscope (TEM). The adhesion strength has been investigated by the pull-off test. The results show that the Cu₆Sn₅, Cu₅Zn₈, and Ag₃Sn IMCs are identified at the Sn-9Zn-1.5Ag-0.5Bi/Cu interface as aging. The adhesion strengths are 12.44±0.58, 8.57±0.43, 5.50±0.78, 4.32±0.78, and 3.32±0.43 MPa for aging times of 0 h, 100 h, 400 h, 700 h, and 1,000 h, respectively.     

Effect of thermal cycling on the adhesion strength of Sn-9Zn-xAg-Cu interface

The effect of thermal cycling on the adhesion strength of the Sn-9Zn-xAg-Cu interface has been investigated by using pull-off tester, X-ray diffractometer, scanning electron microscope and energy dispersive spectrometer. The Sn-9Zn-xAg lead-free solders offer a better thermal cyclic resistance than the 63Sn-37Pb and Sn-9Zn solder alloys. The adhesion strength of the Sn-9Zn-Cu interface increases from 4.4 /spl plusmn/ 0.4 MPa to 13.8 /spl plusmn/ 0.9 MPa with increasing the thermal cycles from zero to three times but it decreases to 8.5 /spl plusmn/ 0.8 MPa for five cycles. The Sn-9Zn-xAg solder alloys (x=0.5, 2.5, and 3.5 wt%) have a similar tendency and the maximum adhesion strength of 21.41 /spl plusmn/ 1.5 MPa for the Sn-9Zn-2.5Ag solder alloy has been obtained after three thermal cycles. The adhesion strength of the Sn-9Zn-1.5Ag-Cu interface increases from 7.8 /spl plusmn/ 0.6 to 16.6 /spl plusmn/ 0.9 MPa with increasing the thermal cycles from 0 to 5 times.     

Comparative study of interfacial reactions of Sn-Ag-Cu and Sn-Ag solders on Cu pads during reflow soldering

The interfacial reaction in soldering is a crucial subject for the solder-joint integrity and reliability in electronic packaging technology. However, electronic industries are moving toward lead-free alloys because of environmental concerns. This drive has highlighted the fact that the industry has not yet arrived at a decision for lead-free solders. Among the lead-free alloys, Sn-3.5Ag and Sn-3.5Ag-0.5Cu are the two potential candidates. Here, detailed microstructural studies were carried out to compare the interfacial reaction of Sn-3.5Ag and Sn-3.5Ag-0.5Cu solder with a ball grid array (BGA) Cu substrate for different reflow times. The Cu dissolution from the substrate was observed for different soldering temperatures ranging from 230°C to 250°C, and the dissolution was found to increase with time and temperature. Dissolution of Cu in the Sn-3.5Ag solder is so fast that, at 240°C, 12 μm of the Cu substrate is fully consumed within 5 min. Much less dissolution is observed for the Sn-3.5Ag-0.5Cu solder. In respect to such high dissolution, there is no significant difference observed in the intermetallic compound (IMC) thickness at the interface for both solder alloys. A simplistic theoretical approach is carried out to find out the amount of Cu₆Sn₅ IMCs in the bulk of the solder by the measurement of the Cu consumption from the substrate and the thickness of the IMCs that form on the interface.     

Effect of soldering and aging time on interfacial microstructure and growth of intermetallic compounds between Sn-3.5Ag solder alloy and Cu substrate

The formation and the growth of the intermetallic compound (IMC, hereafter) at the interface between the Sn-3.5Ag (numbers are all in wt.% unless otherwise specified) solder alloy and the Cu substrate were investigated. Solder joints were prepared by changing the soldering time at 250°C from 30 sec to 10 h and the morphological change of IMCs with soldering time was observed. It resulted from the competition between the growth of IMC and the dissolution of Cu from the substrate and IMCs. They were further aged at 130°C up to 800 h. During aging, the columnar morphology of IMCs changed to a more planar type while the scallop morphology remained unchanged. It was observed that the growth behavior of IMCs was closely related with the initial soldering condition.     

Interfacial reactions in the pb-free composite solders with indium layers

A Pb-free composite solder is prepared with a Pb-free solder substrate and a plated-indium layer. The indium layer melts during the soldering process, wets the substrates, and forms a sound solder joint. Since the melting temperature of indium is 156.6°C, lower than that of the eutectic Sn-Pb, which is at 183°C, the soldering process can be carried out at a temperature lower than that of the conventional soldering process. Composite solder joints with three different Pb-free solders, Sn, Sn-3.5 wt.% Ag, and Sn-3.5 wt.% Ag-0.5 wt.% Cu, and two substrates, Ni and Cu, are prepared. The interfaces between the indium layer, Pb-free solder, and Ni and Cu substrate are examined. A good solder joint is formed after a 2-min reflow at 170°C. A very thick reaction zone at the indium/Pb-free solder interface and a thin reaction layer at the indium/substrate interface are observed.     

Mechanical Properties and Electrochemical Corrosion Behavior of Al/Sn-9Zn-<Emphasis Type="Italic">x</Emphasis>Ag/Cu Joints

The effect of Ag content on the wetting behavior of Sn-9Zn-xAg on aluminum and copper substrates during soldering, as well as the mechanical properties and electrochemical corrosion behavior of Al/Sn-9Zn-xAg/Cu solder joints, were investigated in the present work. Tiny Zn and coarsened dendritic AgZn₃ regions were distributed in the Sn matrix in the bulk Sn-9Zn-xAg solders, and the amount of Zn decreased while that of AgZn₃ increased with increasing Ag content. The wettability of Sn-9Zn-1.5Ag solder on Cu substrate was better than those of the other Sn-9Zn-xAg solders but worse than that of Sn-9Zn solder. The wettability of Sn-9Zn-1.5Ag on the Al substrate was also better than those of the other Sn-9Zn-xAg solders, and even better than that of Sn-9Zn solder. The Al/Sn-9Zn/Cu joint had the highest shear strength, and the shear strength of the Al/Sn-9Zn-xAg/Cu (x = 0 wt.% to 3 wt.%) joints gradually decreased with increasing Ag content. The corrosion resistance of the Sn-9Zn-xAg solders in Al/Sn-9Zn-xAg/Cu joints in 5% NaCl solution was improved compared with that of Sn-9Zn. The corrosion potential of Sn-9Zn-xAg solders continuously increased with increasing Ag content from 0 wt.% to 2 wt.% but then decreased for Sn-9Zn-3Ag. The addition of Ag resulted in the formation of the AgZn₃ phase and in a reduction of the amount of the eutectic Zn phase in the solder matrix; therefore, the corrosion resistance of the Al/Sn-9Zn-xAg/Cu joints was improved.     

Reactions of lead-free solders with CuNi metallizations

We have done experimental research on the dissolution rate and intermetallic growth on Cu, Ni, and CuNi-alloy substrates as a function of time and Cu/Ni ratio of the substrate. Reactions that occur when CuNi metallizations are soldered with lead-free solders were investigated. The experiments were performed using Sn-3.5Ag and Sn-3.8Ag-0.7Cu solders and different CuNi alloys. To determine the rate of dissolution of the substrate material into the solder, CuNi foils of different concentrations were immersed in Sn-3.5Ag and Sn-3.8Ag-0.7Cu solder baths for soldering times ranging from 15 sec to 5 min at 250°C. In addition, reflows of solder balls were made on top of bulk substrates to study the reaction when there is a practically infinite amount of CuNi available compared to the amount of solder. Thin film experiments were also done, where Ni containing under bump metallizations (UBMs) were fabricated and reflowed with eutectic SnAg solder balls. The nickel slows down the dissolution of the UBM into the solder and the formation of intermetallics during reflow compared to Cu metallizations. The solder/UBM interfaces were analyzed with SEM to find out how Ni concentration affects the reaction, and how much Ni is needed to obtain a sufficiently slow reaction rate.     

Intermetallic reactions in Sn-8Zn-20In solder ball grid array packages with Au/Ni/Cu and Ag/Cu pads

During the reflow process of Sn-8Zn-20In solder joints in the ball grid array (BGA) packages with Au/Ni/Cu and Ag/Cu pads, the Au and Ag thin films react with liquid solder to form γ₃-AuZn₄/γ-Au₇Zn₁₈ and ε-AgZn₆ intermetallics, respectively. The γ₃/γ intermetallic layer is prone to floating away from the solder/Ni interface, and the appearance of any interfacial intermetallics cannot be observed in the Au/Ni surface finished Sn-8Zn-20In packages during further aging treatments at 75°C and 115°C. In contrast, ε-CuZn₅/γ-Cu₅Zn₈ intermetallics are formed at the aged Sn-8Zn-20In/Cu interface of the immersion Ag BGA packages. Bonding strengths of 3.8N and 4.0N are found in the reflowed Sn-8Zn-20In solder joints with Au/Ni/Cu and Ag/Cu pads, respectively. Aging at 75°C and 115°C gives slight increases of ball shear strength for both cases.     

The thermal property of lead-free Sn-8.55Zn-1Ag-XAl solder alloys and their wetting interaction with Cu

The wetting behaviors between the quaternary Sn-8.55Zn-1Ag-XAl solder alloys and Cu have been investigated with the wetting balance method. The Al contents, x, of the quaternary solder alloys investigated were 0.01–0.45 wt.%. The results of differential scanning calorimeter (DSC) analysis indicate that the solders exhibit a solid-liquid coexisting range of about 7–10°C. The solidus temperature of the quaternary Sn-8.55Zn-1Ag-XAl solder alloys is about 198.2°C, while the liquidus temperatures are 205–207°C. The experimental results showed that the wettability of the Sn-8.55Zn-1Ag-XAl solder alloys is improved by the addition of Al. The mean maximum wetting force of the solders with Cu is within 0.75–1.18 mN and the mean wetting time is around 1.0–1.1 sec, better than the ∼1.3 sec of eutectic Sn-9Zn and Sn-8.55Zn-1Ag solder alloys. The addition of Al also depresses the formation of ε-Ag-Zn compounds at the interface between Sn-8.55Zn-1Ag-XAl solders and copper.     

Early Interfacial Reaction and Formation of Intermetallic Compounds in the Sn-3.5Ag/Cu Soldering System

The early interfacial reaction in the Sn-3.5Ag/Cu soldering system and the system’s premelting behavior were found and characterized by differential scanning calorimetry incorporated into the reflow process. The results show that the early interfacial reaction occurs by way of melting and wetting of the solder layer adjacent to the Cu substrate at a temperature nearly 4°C below the actual melting point of Sn-3.5Ag solder due to solid-state diffusion of Cu atoms into the Sn-3.5Ag binary solder. Consequently, the early interfacial reaction brings about formation of Cu-Sn intermetallic compounds (IMCs) at a temperature below the melting point of Sn-3.5Ag, and a prolonged early interfacial reaction can lead to change of the Cu-Sn IMC morphology from planar-like to scallop-like and promote excessive growth of IMCs at the interface.     

Interfacial reaction and solder joint reliability of Pb-free solders in lead frame chip scale packages (LF-CSP)

Chip scale packages (CSP) have essential solder joint quality problems, and a board level reliability is a key issue in design and development of the CSP type packages. There has been an effort to eliminate Pb from solder due to its toxicology. To evaluate the various solder balls in CSP package applications, Pb-free Sn-Ag-X (X=In, Cu, Bi) and Sn-9Zn-1Bi-5In solder balls were characterized by melting behavior, phases, interfacial reaction, and solder joint reliability. For studying joint strength between solders and under bump metallurgy (UBM) systems, various UBMs were prepared by electroplating and electroless plating. After T/C (temperature cycle) test, Sn3.5Ag8.5In solder was partially corroded and its shape was distorted. This phenomenon was observed in a Sn3Ag10In 1Cu solder system, too. Their fractured surface, microstructure of solder joint interface, and of bulk solder ball were examined and analyzed by optical microscopy, SEM and EDX. To simulate the real surface mounting condition and evaluate the solder joint reliability on board level, Daisy chain test samples using LF-CSP packages were prepared with various Pb-free solders, then a temperature cycle test (−65∼ 150°C) was performed. All tested Pb-free solders showed better board level solder joint reliability than Sn-36Pb-2Ag. Sn-3.5Ag-0.7Cu and Sn-9Zn-1Bi-5In solders showed 35%, 100% superior solder joint reliability than Sn-36Pb-2Ag solder ball, respectively.     

Properties of quad flat package joints using Sn-Zn-Bi solder with varying lead-plating materials

The effects of plating materials (Sn-10Pb, Sn-3.5Ag, Sn-3Bi, Sn-0.7Cu, and Au/Pd/Ni) on Cu leads on quad flat package (QFP) joints using a Sn-8Zn-3Bi solder were investigated. The joints with Sn-3.5Ag plating and Sn-8Zn-3Bi solder had the slowest growth rate of interfacial reaction layers and the highest strength. The Ag dissolution into the interfacial reaction layers causes this increased strength. The Sn-Ag plating is the best plating material for Cu leads among the five kinds of plating using Sn-8Zn-3Bi solder.     

Mechanisms for interfacial reactions between liquid Sn-3.5Ag solders and cu substrates

Intermetallic compounds formed during the soldering reactions between Sn-3.5Ag and Cu at temperatures ranging from 250°C to 375°C are investigated. The results indicate that scallop-shaped η-Cu₆(Sn_0.933 Ag_0.007)₅ intermetallics grow from the Sn-3.5Ag/Cu interface toward the solder matrix accompanied by Cu dissolution. Following prolonged or higher temperature reactions, ɛ-Cu₃ (Sn_0.996 Ag_0.004) intermetallic layers appear behind the Cu₆(Sn_0.933 Ag_0.007)₅ scallops. The growth of these interfacial intermetallics is governed by a kinetic relation: ΔX=tⁿ, where the n values for η and ɛ intermetallics are 0.75 and 0.96, respectively. The mechanisms for such nonparabolic growth of interfacial intermetallics during the liquid/solid reactions between Sn-3.5Ag solders and Cu substrates are probed.     

Influence of Cu addition to interface microstructure between Sn-Ag solder and Au/Ni-6P plating

The formation and growth of intermetallics at the interface between Sn-Ag-(Cu) alloy balls and Au/Ni-6P plating were experimentally examined as a function of soldering period. Joint strengths were also evaluated by a ball pull test. For the joint with Sn-3.5Ag, the primary reaction product of Ni₃Sn₄ exhibits growth and shrinkage in thickness repeatedly with a passage of reaction time up to 30 min, while the Ni₃SnP reaction layer monotonously increases its thickness without fluctuation. In the cases of the joints with Cu bearing solder, Sn-3Ag-0.5Cu and Sn-3.5Ag-0.8Cu, a single η-(Cu,Ni)₆Sn₅ interface layer grows by fast Cu segregation from liquid solder to the interface layer on soldering. For all the soldered joints, a P-rich layer appears at the surface region of a Ni-6P plating layer by Ni depletion to form those intermetallic compounds at interfaces. The growth rate of a P-rich layer for Sn-3.5Ag is faster by about 4–8 times than those of the Sn-Ag-Cu. The presence of Cu in solder enhances the formation of the Cu₆Sn₅ intermetallic layer at the interface resulting in prevention of Ni diffusion to liquid solder. For all the soldered joints, coarsened reaction interfaces decrease the joint strengths.     

Effect of cooling rate on growth of the intermetallic compound and fracture mode of near-eutectic Sn-Ag-Cu/Cu pad: Before and after aging

Several near-eutectic solders of (1) Sn-3.5Ag, (2) Sn-3.0Ag-0.7Cu, (3) Sn-3.0Ag-1.5Cu, (4) Sn-3.7Ag-0.9Cu, and (5) Sn-6.0Ag-0.5Cu (in wt.% unless specified otherwise) were cooled at different rates after reflow soldering on the Cu pad above 250°C for 60 sec. Three different media of cooling were used to control cooling rates: fast water quenching, medium cooling on an aluminum block, and slow cooling in furnace. Both the solder composition and cooling rate after reflow have a significant effect on the intermetallic compound (IMC) thickness (mainly Cu₆Sn₅). Under fixed cooling condition, alloys (1), (3), and (5) revealed larger IMC thicknesses than that of alloys (2) and (4). Slow cooling produced an IMC buildup of thicker than 10 μm, while medium and fast cooling produced a thickness of thinner than 5 μm. The inverse relationship between IMC thickness and shear strength was confirmed. All the fast- and medium-cooled joints revealed a ductile mode (fracture surface was composed of the β-Sn phase), while the slow-cooled joints were fractured in a brittle mode (fracture surface was composed of Cu₆Sn₅ and Cu₃Sn phases). The effect of isothermal aging at 130°C on the growth of the IMC, shear strength, and fracture mode is also reported.     

Improved mechanical properties in new,Pb-free solder alloys

The mechanical properties of solders benefit from uniform dispersion of fine precipitates and small effective grain sizes. Metallurgical methods of attaining such a beneficial microstructure have been investigated in two new, near-eutectic, Pb-free solder alloys systems—Sn-Zn-In (m.p. ∼188°C) and Sn-Ag-Zn (m.p.∼217°C). It has been found that small alloying additions of Ag dramatically improve the mechanical properties of the ternary Sn-8Zn-5In alloy. The improvement is attributed to the elimination of the coarse and nonuniform distribution of plate-like dendrites and refining the effective grain size in the solidified microstructure. Also, small amounts of Cu dramatically improve the ductility in the ternary Sn-3.5Ag-lZn alloy. The quaternary Sn-3.5Ag-lZn-0.5Cu has better mechanical properties than the binary Sn-3.5Ag alloy because it has a uniform fine dispersion of precipitates and a small effective grain size. The combination of high mechanical strength and high ductility is likely to yield improved fatigue resistance properties in the interconnection of electronic components.     

Growth of intermetallic compounds in the Sn-9Zn/Cu joint

We have studied the microstructure of the Sn-9Zn/Cu joint in soldering at temperatures ranging from 230°C to 270°C to understand the growth of the mechanism of intermetallic compound (IMC) formation. At the interface between the Sn-9Zn solder and Cu, the results show a scallop-type ε-CuZn₄ and a layer-type γ-Cu₅Zn₈, which grow at the interface between the Sn-9Zn solder and Cu. The activation energy of scallop-type ε-CuZn₄ is 31 kJ/mol, and the growth is controlled by ripening. The activation energy of layer-type γ-Cu₅Zn₈ is 26 kJ/mol, and the growth is controlled by the diffusion of Cu and Zn. Furthermore, in the molten Sn-9Zn solder, the results show η-CuZn grains formed in the molten Sn-9Zn solder at 230°C. When the soldering temperature increases to 250°C and 270°C, the phase of IMCs is ε-CuZn₄.     

Contact angle measurements of Sn-Ag and Sn-Cu lead-free solders on copper substrates

In this study, the contact angles of four lead-free solders, namely, Sn-3.5Ag, Sn-3.5Ag-4.8Bi, Sn-3.8Ag-0.7Cu, and Sn-0.7Cu (wt.%), were measured on copper substrates at different temperatures. Measurements were performed using the sessile-drop method. Contact angles ranging from 30° to 40° after wetting under vacuum with no fluxes and between 10° and 30° with rosin mildly activated (RMA) and rosin activated (RA) fluxes were obtained. The Sn-3.5Ag-4.8Bi exhibited the lowest contact angles, indicating improved wettability with the addition of bismuth. For all soldering alloys, lower contact angles were observed using RMA flux. Intermetallics formed at the solder/Cu interface were identified as Cu₆Sn₅ adjacent to the solder and Cu₃Sn adjacent to the copper substrate. The Cu₃Sn intermetallic phase was generally not observed when RMA flux was used. The effect of temperature on contact angle was dependent on the type of flux used.     

Electrochemical Properties of Joints Formed Between Sn-9Zn-1.5Ag-1Bi Alloys and Cu Substrates in a 3.5 wt.% NaCl Solution

The electrochemical properties of the joints formed between Sn-9Zn-1.5Ag-1Bi alloys and Cu substrates in a 3.5 wt.% NaCl solution have been investigated by potentiodynamic polarization, X-ray diffraction, and scanning electron microscopy. For the Sn-9Zn-1.5Ag-1Bi/Cu joints in a 3.5 wt.% NaCl solution, corrosion current (I _corr), corrosion potential (E _corr) and corrosion resistance (R _p) are 2.46 × 10⁻⁶ A/cm², −1.18 V, and 7.54 × 10³ Ωcm², respectively. Cu₆Sn₅, Cu₅Zn₈, and Ag₃Sn are formed at the interface between the Sn-9Zn-1.5Ag-xBi solder alloy and Cu substrate. The corrosion products of ZnCl₂, SnCl₂ and ZnO are formed at the Sn-9Zn-1.5Ag-xBi/Cu joints after polarization in a 3.5 wt.% NaCl solution. Pits are also formed on the surface of the solder alloys.