Tissue engineering scaffolds of mesoporous magnesium silicate and poly(ε-caprolactone)–poly(ethylene glycol)–poly(ε-caprolactone) composite

Mesoporous magnesium silicate (m-MS) and poly(ε-caprolactone)–poly(ethylene glycol)–poly(ε-caprolactone) (PCL–PEG–PCL) composite scaffolds were fabricated by solvent-casting and particulate leaching method. The results suggested that the incorporation of m-MS into PCL–PEG–PCL could significantly improve the water adsorption of the m-MS/PCL–PEG–PCL composite (m-MPC) scaffolds. The in vitro degradation behavior of m-MPC scaffolds were determined by testing weight loss of the scaffolds after soaking into phosphate buffered saline (PBS), and the result showed that the degradation of m-MPC scaffolds was obviously enhanced by addition of m-MS into PCL–PEG–PCL after soaking for 10 weeks. Proliferation of MG63 cells on m-MPC was significantly higher than MPC scaffolds at 4 and 7 days. ALP activity on the m-MPC was obviously higher than MPC scaffolds at 7 days, revealing that m-MPC could promote cell differentiation. Histological evaluation showed that the introduction of m-MS into PCL–PEG–PCL enhanced the efficiency of new bone formation when the m-MPC scaffolds implanted into bone defect of rabbits. The results suggested that the inorganic/organic composite of m-MS and PCL–PEG–PCL scaffolds exhibited good biocompatibility, degradability and osteogenesis.     

Poly(acrylonitrile-co-itaconic acid)–poly(3,4-ethylenedioxythiophene) and poly(3-methoxythiophene) nanoparticles and nanofibres

This work aimed to produce poly(acrylonitrile-co-itaconic acid) (P(AN-co-IA)) nanocomposites with poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3-methoxythiophene) (PMOT). An anionic surfactant sodium dodecyl benzene sulphonate was used in emulsion polymerization for nanocomposite production. Incorporations of PEDOT and PMOT on the nanoparticles were characterized by scanning electron microscopy (SEM), atomic force microscopy, Fourier transform infrared-attenuated total reflectance spectroscopy and ultra-violet spectroscopy. These nanoparticles were blended with PAN and the blends were electrospun to produce P(AN-co-IA)–polythiophene-derivative-based nanofibres, and the obtained nanofibres were characterized by SEM and energy dispersive spectroscopy. In addition, electrochemical impedance studies conducted on nanofibres showed that PEDOT and PMOT in matrix polymer P(AN-co-IA) exhibited capacitive behaviour comparable to that of ITO–PET. Their capacitive behaviour changed with the amount of electroactive polymer.     

Mechanical studies on poly(vinyl chloride)–poly(methyl methacrylate)-based polymer electrolytes

The aim of the present work is to study the mechanical properties of poly(vinyl chloride) (PVC)/poly(methyl methacrylate) (PMMA) blends based polymer electrolytes for lithium ion batteries. The introduction of PVC into PMMA is found to increase the Young’s modulus value from 5.19 MPa (in pure PMMA) to 6.05 MPa (in PVC:PMMA = 70:30). The different Young’s modulus values in PVC blends is due to the difference in the cross-linking density provided by PVC with different weight fraction values. The stress–strain analysis reveals that the mechanical strength of the polymer electrolyte system deteriorated with the incorporation of LiCF₃SO₃. The results show that the introduction of salt decreases the Young’s modulus and stress at peak values along with higher elongation at peak value. The addition of low molecular weight plasticizers to PVC–PMMA–LiCF₃SO₃ decreases the modulus and stress at peak of the complexes. To be applicable in practical applications, the mechanical strength of the plasticized films is found to improve with the addition of silica as nanocomposite filler.     

Non-conventional injection molding of poly(lactide) and poly(ε-caprolactone) intended for orthopedic applications

Biodegradable polymers such as poly(lactide) (PLA) and poly(epsilon-caprolactone) (PCL) are increasingly used in biomedical applications as temporary implants. However, melt processing of these materials in particular of PLA is difficult due to the temperature sensitivity. Within this study, PLA and PCL were injection molded conventionally and by using the process shear controled orientation in injection molding (SCORIM) in order to investigate the effect of processing parameters on the physical properties of the moldings. Therefore, flexural testing, differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), molecular weight (MW) and orientation measurements were performed. PLA showed high sensitivity to melt temperature. In the case of amorphous poly(DL-lactide), the molecular weight and subsequently the ductility is substantially reduced by processing at higher melt temperatures. In the case of crystallizable poly(L-lactide), higher melt temperatures and shear induced by the SCORIM process resulted in enhanced crystallinity, which compromised the mechanical properties. Generally, SCORIM processing improved the mechanical properties, in particular the ductility, by orientating the molecular structure. PCL was shown to be less sensitive to shear and temperature than PLA. Stress at yield and stiffness are more improved by SCORIM processing. However, the processing temperature in combination with the grade used proved to be influential for the mechanical properties of resulting moldings.     

Microencapsulation of cytarabine using poly(ethylene glycol)–poly(ε-caprolactone) diblock copolymers as surfactant agents

Background: The high water solubility and the low molecular weight of cytarabine (Ara-C) are major obstacles against its particulate formulation as a result of its low affinity to the commonly used hydrophobic polymers. Methods: Biodegradable cytarabine loaded-microparticles (Ara-C MPs) were elaborated using poly(?-caprolactone) (PCL) and monomethoxy polyethylene glycol (mPEG)–PCL diblock copolymer in order to increase the hydrophilicity of the polymeric matrix. For this purpose, a series of mPEG–PCL diblock copolymers with different PCL block lengths were synthesized. Compositions and molecular weights of obtained copolymers were characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance, size exclusion chromatography, and size exclusion chromatography–multi-angle laser light scattering. Ara-C MPs were prepared by double emulsion-solvent evaporation method. The effects of varying PCL block lengths on microparticle encapsulation efficiency, size, and zeta potential were evaluated. Results: Increasing the PCL block lengths of copolymers substantially increased the Ara-C encapsulation efficiency and the microparticle size but it decreased their zeta potential. Microparticles were spherical in shape, with a smooth surface and composed of homogenously distributed Ara-C-containing aqueous domains in the polymer matrix. The in vitro drug release kinetics of the optimized microparticles showed a hyperbolic profile with an initial burst release. Conclusion: These results showed the important role of the amphiphilic diblock copolymers as stabilizing agent in the encapsulation of Ara-C in PCL microparticles, suggesting their potential use for the microparticulate formulations of other small hydrophilic bioactive molecules.     

Structure,swelling, and drug release of thermoresponsive poly(amidoamine) dendrimer–poly(N-isopropylacrylamide) hydrogels

Functional drug delivery systems are important for improved pharmacotherapy. The aim of this work was to describe how the introduction of varying amounts of the dendrimer polyamidoamine (PAMAM) into a chemically cross-linked thermoresponsive poly(N-isopropylacrylamide) (PNIPAAM) gel affects the structure, swelling properties, and drug release characteristics. The structure of the gel system was characterized by small-angle X-ray scattering (SAXS), while the drug delivery system was characterized by measuring the swelling, loading, and release of the model drug. The SAXS results suggest that the PNIPAAM gel is heterogeneous on a local length scale, whereas more homogeneous gels are formed in the presence of PAMAM. Increased swelling and loading capacity were observed for higher fractions of PAMAM dendrimer. This was explained by the enhanced hydrophilicity obtained by inclusion of the dendrimers. The swelling process was observed to be very slow taking place over several days, indicating other mechanisms than diffusion to be the rate-limiting step. The temperature-induced deswelling was more pronounced for the dendrimer-containing formulations. This process was observed to be very fast and complete within a couple of hours. Similarly the release rate was quite fast without being affected by inclusion of the dendrimer. Retention of a significant portion of the loaded drug at specific conditions was shown to be due to the hydrogen bonding ability of PNIPAAM. Improved conditions for drug delivery were achieved in several respects by incorporation of PAMAM dendrimer molecules in the PNIPAAM hydrogel. Our results indicate that the PAMAM entities expand the PNIPAAM gel and that the gel becomes more homogeneous.     

Preparation and properties of polyrotaxane from α-cyclodextrin and poly(ethylene glycol) with poly(vinyl alcohol)

α–Cyclodextrin (α-CD) was found to form inclusion complexes with poly(ethylene glycol) (PEG) having a crystalline state in high yields, which have been investigated extensively in the past. Formation of an inclusion complex depends strongly on structure, molecular weight and geometry of the polymer. Development of a dicomponent inclusion complex (DIC) of PEG and α-CD in the presence of poly(vinyl alcohol) (PVA) and initiation of hexagonal crystals upon sonication have exhibited various microstructures. Formation of the new inclusion complex in PVA heavily depends on the concentration of PVA, temperature and sonication time. The complexes produced are characterized by FTIR, HNMR spectra and powder X-ray. ¹HNMR of the complexes demonstrate that their stoichiometric ratio is 2:1 (two ethylene glycol units and one α-CD). X-ray patterns of PEG–α-CD complex indicate that the α-CD forms channels whereas PEG/α-CD/PVA creates cage-type structures.     

Self-assembly of graft polyurethanes having both crystallizable poly(ε-caprolactone) blocks and soft poly(n-butyl acrylate) segments

We report the self-assembly behavior of graft polyurethanes combining in its structure soft lateral poly(n-butyl acrylate) (PnBuA) chains with rigid and crystallizable polycaprolactone (PCL) segments. Segmented polyurethanes microphase separated into high-glass transition temperature PCL hard and low-glass transition temperature PnBuA soft domains. The variation of the microstructure as a function of the hard segment content (ratio hard to soft segments) within the structure has been studied by using atomic force microscopy. Additionally, the crystallization mechanism appeared to be directly related to the properties of the substrates forming parallel lamellar structures on hydrophilic substrates and perpendicular lamellae with hydrophobic substrates.     

Composition-dependent physical properties of poly[(vinylidene fluoride)-co-trifluoroethylene]–poly(ethylene oxide) blends

Polymer blends based on poly(vinylidene fluoride-co-trifluoroethylene) copolymers, P(VDF-TrFE), and poly(ethylene oxide), PEO, with varying compositions have been prepared by solvent casting. In this way, P(VDF-TrFE) crystallizes from the solution while solvent evaporates, while PEO crystallizes from the melt during cooling to room temperature. The surface morphology of the polymer blends indicates the transition from the fibrillar microstructure typical of PVDF-TrFE to the spherulite structure characteristic of PEO. The vibration mode characteristics of P(VDF-TrFE) are not influenced by the presence of PEO in the polymer blend. Confinement of PEO in the P(VDF-TrFE) phase change the conformation of PEO from trans to helix, increasing this transformation for increasing P(VDF-TrFE) content in the polymer blends. Sequential crystallization of the two polymers produce separated amorphous phases whose independent cooperative conformational motions are revealed by two main dynamic-mechanical relaxations. No chemical interaction seems to exist between the polymers within the blend.     

Tailoring impact toughness of poly(L-lactide)/poly(ε-caprolactone) (PLLA/PCL) blends by controlling crystallization of PLLA matrix

Melt blending poly(L-lactide) (PLLA) with various biodegradable polymers has been thought to be the most economic and effective route to toughen PLLA without compromising its biodegradability. Unfortunately, only very limited improvement in notched impact toughness can be achieved, although most of these blends show significant enhancement in tensile toughness. In this work, biodegradable poly(ε-caprolactone) (PCL) was used as an impact modifier to toughen PLLA and a nucleating agent was utilized to tailor the crystallization of PLLA matrix. Depending on the nucleating agent concentrations in the matrix and mold temperatures in injection molding, PLLA/PCL blends with a wide range of matrix crystallinity (10-50%) were prepared by practical injection molding. The results show that there is a linear relationship between PLLA matrix crystallinity and impact toughness. With the increase in PLLA crystalline content, toughening becomes much easier to achieve. PLLA crystals are believed to provide a path for the propagation of shear yielding needed for effective impact energy absorption, and then, excellent toughening effect can be obtained when these crystals percolate through the whole matrix. This investigation provides not only a new route to prepare sustainable PLLA products with good impact toughness but also a fresh insight into the importance of matrix crystallization in the toughening of semicrystalline polymers with a flexible polymer.     

Fabrication of flexible conductive films derived from poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) on the nonwoven fabrics substrate

In this research, conducting poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) aqueous dispersion was synthesized at first via chemical oxidative polymerization and followed by mixing it with poly(styrene-r-butyl acrylate) P(St-BA) aqueous latex, creating a conductive material with outstanding stretchability. The elastic conductive composite were then film formed on the glass and poly(ethylene terephthalate) (PET) nonwoven fabric substrate by spin coating and dip coating, respectively. Composite films with various contents of PEDOT:PSS polymer (10–100 wt.%) had been prepared. From the conductivity measurements, the conductivity was still kept as high as 88 S cm⁻¹ even the PEDOT:PSS content was lowered to 10 wt.%. Furthermore, the elasticity of conductive films on the PET-nonwoven fabric substrate was evaluated by the 180° bending test repeating 100 times. With introducing soft P(St-BA) material in the PEDOT:PSS phase, the surface resistance increased merely 3–6 times after bending 100 times, while the surface resistance for pure PEDOT:PSS film could reach 18–20 times.     

Preparation and characterization of poly(3,4-ethylenedioxythiophene)–poly(styrene sulfonate) composite thin films highly loaded with platinum nanoparticles

In this work, we propose a simple and efficient, low-temperature (∼120 °C) process to prepare transparent thin films of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonate) (PEDOT:PSS) loaded with high concentration (up to 22.5 wt%) of platinum (Pt) nanoparticles. Firstly, an improved polyol method was modified to synthesize nano-sized (∼5 nm) and mono-dispersed Pt particles. These nanoparticles were incorporated into the matrix of PEDOT:PSS thin films via a spin coating/drying procedure. The electrochemical activities of the PEDOT:PSS thin film modified electrodes with respect to the I⁻/I₃⁻ redox reactions were investigated. It was found that the modified electrode of PEDOT:PSS thin film containing 22.5 wt% Pt exhibited the electrochemical activity comparable to the conventional Pt thin film electrode, suggesting that this electrode has good potential to serve as a counter electrode in dye-sensitized solar cells.     

Morphology of solution-grown poly(β-propiolactone) single crystals

Single crystals of poly(-propiolactone) (PPL) with different molecular weights (M _w = 70000 and M _w = 2300) were grown from four kinds of solvents under isothermal crystallization condition. The morphologies and crystal structures of PPL single crystals were investigated by means of transmission electron microscopy and atomic force microscopy. The single crystals of high-molecular-weight PPL (HMW-PPL) grown from cyclohexanone appeared elongated with dimensions of around 0.2–0.8 m along the short and 5–10 m along the long axes. Single crystals of low-molecular-weight PPL grown from cyclohexanone showed three to five elliptical-shaped lamellae, from central nucleus like petals. The long axes of both single crystals corresponded to the crystallographic b axis. The reciprocal lattice parameters: a* = 2.045 nm^–1, b* = 1.420 nm^–1 and * = 90° could be determined from electron diffractograms. Decoration of the crystals with polyethylene suqqested that the single crystals of HMW-PPL have regular chain-folding along their long axis in the [010] direction with consecutive folds in the [110] and [1 0] directions. Accordingly, it is deduced that HMW-PPL has the anti-parallel chain-packing structure.     

Ionic conductivity and diffusion coefficient of barium-chloride-based polymer electrolyte with poly(vinyl alcohol)–poly(4-styrenesulphonic acid) polymer complex

A composite polymer electrolyte comprising poly(vinyl alcohol)–poly(4-styrenesulphonic acid) with barium chloride dihydrate (\(\hbox {BaCl}_{2}{\cdot } 2\hbox {H}_{2}\hbox {O}\)) salt complex has been synthesized following the usual solution casting. The ionic conductivity of polymer electrolyte was analysed by impedance spectroscopy. The highest room temperature (at 30\({^{\circ }}\)C) conductivity evaluated was 9.38 \(\times \) 10\(^{-6}\) S cm\(^{-1}\) for 20 wt% loading of \(\hbox {BaCl}_{2}\) in the polymer electrolyte. This has been referred to as the optimum conducting composition. The temperature-dependent ionic conductivity of the polymer electrolyte exhibits the Arrhenius relationship, which represents the hopping of ions in polymer composites. Cation and anion diffusion coefficients are evaluated using the Trukhan model. The transference number and enhanced conductivity imply that the charge transportation is due to ions. Therefore this polymer electrolyte can be further studied for the development of electrochemical device applications.     

Osteogenic differentiation of rat bone mesenchymal stem cells cultured on poly (hydroxybutyrate-co-hydroxyvalerate), poly (ε-caprolactone) scaffolds

Journal of Materials Science: Materials in Medicine - A thin endocrown restoration was often applied in endodontically treated teeth with vertical bite height loss or inadequate clinical crown...     

pH-stimuli-responsive near-infrared optical imaging nanoprobe based on poly(γ-glutamic acid)/poly(β-amino ester) nanoparticles

pH-stimuli-responsive near-infrared optical imaging nanoprobes are designed and synthesized in this study in a facile one-step synthesis process based on the use of the biocompatible and biodegradable polymer poly(γ-glutamic acid) (γ-PGA)/poly(β-amino ester) (PBAE). PBAE has good transfection efficiency and promotes degradation properties under acidic conditions. This pH-responsive degradability can be used for the effective release of encapsulating materials after cellular uptake. As an optical imaging probe, indocyanine green (ICG) is an FDA-approved near-infrared fluorescent dye with a quenching property at a high concentration. In this regard, we focus here on the rapid degradation of PBAE in an acidic environment, in which the nanoparticles are disassembled. This allows the ICG dyes to show enhanced fluorescence signals after being releasing from the particles. We demonstrated this principle in cellular uptake experiments. We expect that the developed pH-stimuli-responsive smart nanoprobes can be applied in intracellular delivery signaling applications.     

Crystalline thin films of β-phase poly(9,9-dioctylfluorene)

The detailed structure of crystalline β-phase poly(9,9-dioctylfluorene) (PFO) films was studied by polarized optical measurements, transmission electron microscopy, and grazing-incidence X-ray diffraction. Crystalline β-phase PFO thin films were fabricated by a friction transfer technique and subsequent vapor treatment. Compared to the α-phase, the lattice parameters of the β-phase crystals shrank along the a-axis (film thickness direction) and elongated along the b-axis (side-chain direction), but the period along the c-axis (main-chain direction) remained nearly equal. These changes in molecular packing were consistent with a planar conformational change from the α-phase to the β-phase of PFO.     

Scaffolds of poly (ε-caprolactone) with whiskers of hydroxyapatite

Scaffolds of Poly (ε-caprolactone)/hydroxyapatite were produced and studied for tissue engineering applications. The materials were selected due to its biodegradability (PCL) and bioactivity (HA), and above all their biocompatibility toward the human tissue. The composites produced were characterized by SEM, XRD, and EDS. By analyzing these characterizations it was possible to obtain further information about the composition and morphology aspects of all portions of the composite scaffold.