Microstructure and mechanical properties of gas pressure sintered Al2O3/TiCN composite

Al₂O₃–30 wt.%TiCN composites have been fabricated successfully by a two-stage gas pressure sintering schedule. The gas pressure sintered Al₂O₃–30 wt.%TiCN composite achieved a relative density of 99.5%, a bending strength of 772 MPa, a hardness of 19.6 GPa, and a fracture toughness of 5.82 MPa m^1/2. The fabrication procedure involves solid state sintering of two phases without solubility to prepare Al₂O₃–TiCN composite. Little grain growth occurred for TiCN during sintering while Al₂O₃ grains grew about three times to an average size of 3–5 μm. The interface microstress arising during cooling from the processing temperature because of the thermal and/or mechanical properties mismatch between the Al₂O₃ and TiCN phase is about 50 MPa. Such a compressive microstress is not high enough to cause grain boundary cracking that may weaken the composite but it can introduce dislocations within grains, which is very good to enhance the composite properties.     

Gas pressure sintering of Al2O3/TiCN composite

Al₂O₃/TiCN composites have been fabricated by gas pressure sintering, which overcomes the limitations of hot pressing. The densification behavior and mechanical properties of the Al₂O₃ gas pressure sintered with 30 wt.% TiCN at different temperatures have been investigated. The gas pressure sintered Al₂O₃–30 wt.%TiCN composite achieved a relative density of 99.5%, a bending strength of 772 MPa, a hardness of 19.6 GPa, and a fracture toughness of 5.82 MPa·M^1/2.     

MoSi2–Al2O3 electroconductive ceramic composites

Al₂O₃–MoSi₂ composites with MoSi₂ volume fractions between 16 and 40% were fabricated from commercial ceramic Al₂O₃ and intermetallic MoSi₂ powders by granulation, cold isostatic pressing and vacuum-sintering. The addition of MoSi₂ had only a slight influence on the densification of the composites, with sintered densities of 98% for samples with 16 vol.% MoSi₂ and 94% for samples with 40 vol.% MoSi₂. Composites with MoSi₂ contents of 20 vol.% and higher were electroconductive due to the formation of a three-dimensional percolating network of the conductive MoSi₂ phase.     

Polysilazane derived micro/nano Si3N4/SiC composites

The pyrolised polysilazanes poly(hydridomethyl)silazane NCP 200 and poly(urea)silazane CERASET derived Si–C–N amorphous powders were used for preparation of micro/nano Si₃N₄/SiC composites by hot pressing. Y₂O₃–Al₂O₃ and Y₂O₃–Yb₂O₃ were used, as sintering aids. The resulting ceramic composites of all compositions were dense and polycrystalline with fine microstructure of average grain size <1 μm of both Si₃N₄ and SiC phases. The fine SiC nano-inclusions were identified within the Si₃N₄ micrograins. Phase composition of both composites consist of , β modifications of Si₃N₄ and SiC. High weight loss was observed during the hot pressing cycle, 12 and 19 wt.% for NCP 200 and CERASET precursors, respectively. The fracture toughness of both nanocomposites (NCP 2000 and CERASET derived) was not different. Indentation method measured values are from 5 to 6 MPa m^1/2, with respect to the sintering additive system. Fracture toughness is slightly sensitive to the SiC content of the nanocomposite. Hardness increases with the content of SiC in the nanocomposite. The highest hardness was achieved for pyrolysed CERASET precursor with 2 wt.% Y₂O₃ and 6 wt.% Yb₂O₃, HV 23 GPa. This is a consequence of the highest SiC content as well as the chemical composition of additives.     

In-situ growth of needlelike LaAl11O18 for reinforcement of alumina composites

In situ growth of needlelike LaAl₁₁O₁₈ grains reinforcing Al₂O₃ composites can be fabricated by a coprecipitation method using La(NO₃)₃√6H₂O and Al(NO₃)₃√9H₂O as starting materials. The new two-step process involved firstly preparing needlelike LaAl₁₁O₁₈ grains distributed homogeneously in Al₂O₃ powder and then pressureless sintering the composite powders. The Al₂O₃/25 vol.%LaAl₁₁O₁₈ samples pressureless sintered at 1550°C for 4 h achieve relative density up to 96.5% and exhibit a bending strength of 420±30 MPa and a fracture toughness of 4.3±0.4 MPa m^1/2.     

Tailoring of alumina surfaces as supports for NiMo sulfide catalysts in the ultra deep hydrodesulfurization of gas oil: case study of TiO2-coated alumina prepared by chemical vapor deposition technique

The present paper gives a detailed review of the different studies under investigation in our laboratory concerning the use of TiO₂ and TiO₂–Al₂O₃ composites prepared by chemical vapor deposition (CVD) as support for sulfide catalysts in the HDS of dibenzothiophene (DBT) derivatives. The supports investigated here are: TiO₂ (from Degussa, 50 m²/g), Al₂O₃ (Nikki, 186 m²/g) and TiO₂–Al₂O₃ supports prepared by CVD of TiCl₄ on alumina. Using several characterization techniques, we have demonstrated that the support composite presents a high dispersion of TiO₂ over γ-Al₂O₃ without forming precipitates up to ca. 11 wt.% loading. Moreover, the textural properties of the support composite are comparable to those of alumina. XPS investigations of Mo and NiMo catalysts supported on the different carriers show that Mo-oxide species exhibit a higher degree of sulfidation on the surface of TiO₂ and TiO₂–Al₂O₃ than on alumina. The HDS tests of 4,6-DMDBT under mild operating conditions (573 K, 3 MPa) show that sulfide catalysts supported on the composite support (ca. 11 wt.%) are more active than those supported on to TiO₂ or Al₂O₃. This higher HDS catalytic activity is attributed to the promotion of the hydrodesulfurization pathway, whereby the pre-hydrogenation of one of the aromatic rings adjacent to the thiophenic one may reduce the steric hindrance caused by the two methyl groups adjacent to the sulfur atom during the C–S bond cleavage.     

Thermodynamics of the Al–C–O system and properties of SiC–AlN–Al2OC composites

Based on a recent thermodynamic evaluation of the Al–C–O system, the standard Gibbs free energies of formation of both aluminium oxycarbides Al₄O₄C and Al₂OC are given, and a classical stability diagram is shown at 2100 K. Because Al₂OC is unstable below 1715 °C, the stable würtzite compound 2AlN.Al₂OC has been preferred, and formed in-situ as the second phase in SiC-based composites. Starting with commercial powders of -SiC, AlN, Al₂O₃ and Al₄C₃, dense materials are obtained by pressureless sintering (up to 2020 °C) or hot-pressing (up to 1950 °C), owing to the liquid phase from the Al₂O₃–Al₄C₃ system. The existence of a miscibility gap is shown, and the microstructures are fine grained and equiaxed. Compared with SiC–Al₂OC alloys, the hot-pressed materials with 90 wt% SiC exhibit slightly higher mechanical properties and a good retention nearly up to 1500 °C.     

Design of 7 wt.% Y2O3–ZrO2/mullite plasma-sprayed composite coatings for increased creep resistance

Plasma-sprayed stand-alone coatings of 7 wt.% Y₂O₃–ZrO₂ (YSZ), nominally 74 wt.% Al₂O₃–26 wt.% SiO₂ mullite, and a 46:54 volume ratio composite of YSZ to mullite were examined using X-ray diffraction, dilatometry, and compression creep. X-ray diffraction and dilatometer results showed that the as-sprayed predominantly amorphous mullite crystallized at 970 °C. Creep tests were conducted on all three coating types in the as-sprayed condition at stresses from 40 to 80 MPa and temperatures of 1000–1200 °C. The primary deformation mechanism in coatings made from all three materials was stress-assisted densification of the porous coating. While the creep behavior of YSZ/mullite composite specimens was between that of pure YSZ and pure mullite specimens for all combinations of temperature and stress tested, the creep response of the composite was more similar to that of pure mullite for all cases tested, consistent with mullite being the continuous phase in the composite.     

Effect of sintering additives on microstructures and mechanical properties of short-carbon-fiber-reinforced SiC composites prepared by precursor pyrolysis–hot pressing

Short-carbon-fiber-reinforced SiC composites were prepared by precursor pyrolysis–hot pressing with MgO–Al₂O₃–Y₂O₃ as sintering additives. The effects of the amount of sintering additives on microstructure and mechanical properties of the composites were investigated. The results showed that the composites could be densified at a relatively low temperature of 1800 °C via the liquid-phase sintering mechanism and the composite density and mechanical properties improved with the amount of additives. The amorphous interphase in the composites with more additive content, not only avoided the direct contact of the fibers with matrix, but also improved the fiber–matrix bonding. It proved that the fiber–matrix interphase characteristics played a key role in controlling mechanical properties of the composites.     

Phase diagram of the Al2O3–ZrO2–Nd2O3 system

The phase diagram of the Al₂O₃–ZrO₂–Nd₂O₃ system was constructed in the temperature range 1250–2800 °C. The liquidus surface of the phase diagram reflects the preferentially eutectic interaction in the system. Two new ternary and one new binary eutectics were found. The minimum melting temperature is 1675 °C and it corresponds to the ternary eutectic Nd₂O₃·11Al₂O₃ + F-ZrO₂ + NdAlO₃. The solidus surface projection and the schematic of the alloy crystallization path confirm the preferentially congruent character of phase interaction in the ternary system. The polythermal sections present the complete phase diagram of the Al₂O₃–ZrO₂–Nd₂O₃ system. No ternary compounds or regions of remarkable solid solution were found in the components or binaries in this ternary system.     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

Phase diagram of the system: Al2O3–ZrO2

The system Al₂O₃–ZrO₂ was studied by differential thermal analysis in inert atmosphere and in vacuum. The eutectic was located at 1866°C and 40% mass of ZrO₂. Zirconia solid solution at the eutectic temperature is up to 1.1±0.3% mass of Al₂O₃. Enthalpy of melting of this eutectic is 1080±90 J/g. Pure ZrO₂ transforms from monoclinic to tetragonal at 1162±7°C, but the saturated solid solution of ZrO₂, with 0.7±0.2% mass Al₂O₃ at this temperature, transforms at 1085±5°C. Inverse transitions occur with hysteresis correspondingly at 1055±5 and 995±5°C. Enthalpy of transformation of pure ZrO₂ from monoclinic to tetragonal phase is 42±5 J/g (5.2±0.6 J/mol) but only 30±5 J/g for a ZrO₂ saturated solid solution.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Processing of hot pressed Al2O3–Cr2O3/Cr-carbide nanocomposite prepared by MOCVD in fluidized bed

Nanosized particles dispersed uniformly on Al₂O₃ particles were prepared from the decomposition of precursor Cr(CO)₆ by metal organic chemical vapor deposition (MOCVD) in a fluidized chamber. These nanosized particles consisted of Cr₂O₃, CrC_1−x, and C. A solid solution of Al₂O₃–Cr₂O₃ and an Al₂O₃–Cr₂O₃/Cr₃C₂ nanocomposite were formed when these fluidized powders were pre-sintered at 1000 and 1150 °C before hot-pressing at 1400 °C, respectively. In addition, an Al₂O₃–Cr₂O₃/Cr-carbide (Cr₃C₂ and Cr₇C₃) nanocomposite was formed when the particles were directly hot pressed at 1400 °C. The interface between Cr₃C₂ and Al₂O₃ is non-coherent, while the interface between Cr₇C₃ and Al₂O₃ is semi-coherent.     

Piezoelectric properties of Pb(Mn1/3Nb2/3)O3–PbZrO3–PbTiO3 ceramics with sintering aid of 2CaO–Fe2O3 compound

Since the electromechanical devices move towards enhanced power density, high mechanical quality factor (Q_m) and electromechanical coupling factor (k_p) are commonly needed for the high powered piezoelectric transformer with Q_m≥2000 and k_p=0.60. Although Pb(Mn_1/3Nb_2/3)O₃–PbZrO₃–PbTiO₃ (PMnN–PZ–PT) ceramic system has potential for piezoelectric transformer application, further improvements of Q_m and k_p are needed. Addition of 2CaO–Fe₂O₃ has been proved to have many beneficial effects on Pb(Zr,Ti)O₃ ceramics. Therefore, 2CaO–Fe₂O₃ is used as additive in order to improve the piezoelectric properties in this study. The piezoelectric properties, density and microstructures of 0.07Pb(Mn_1/3Nb_2/3)O₃–0.468PbZrO₃–0.462PbTiO₃ (PMnN–PZ–PT) piezoelectric ceramics with 2CaO–Fe₂O₃ additive sintered at 1100 and 1250 °C have been studied. When sintering temperature is 1250 °C, Q_m has the maximum 2150 with 0.3 wt.% 2CaO–Fe₂O₃ addition. The k_p more than 0.6 is observed for samples sintered at 1100 °C. The addition of 2CaO–Fe₂O₃ can significantly enhance the densification of PMnN–PZ–PT ceramics when the sintering temperature is 1250 °C. The grain growth occurred with the amount of 2CaO–Fe₂O₃ at both sintering temperatures.     

Sinterability, crystallization and properties of glass–ceramic tiles belonging to CaF2–CaO–MgO–Al2O3–SiO2 system

The effect of CaO substitution by different amounts of MgO on crystallization and various properties of CaF₂–CaO–Al₂O₃–SiO₂ glass system were investigated. It was shown that the properties of obtained glass–ceramics are greatly influenced by MgO contents. The Avrami exponent and activation energy for crystallization of the most promising and the MgO-free specimens were determined. Results suggested that surface crystallization was the main precipitation mechanism of both samples and while the activation energy for crystallization of MgO containing sample was less than MgO-free one, its ability to crystallize was diminished. SEM results confirm occurrence of surface crystallization of samples and depicts the phenomenon of microstructure coarsening by increasing MgO content and also reduced densification of specimen with magnesium oxide more than 9 wt.%.     

Ethylene dimerization over NiSO4 supported on Fe2O3-promoted ZrO2 catalyst

The NiSO₄ supported on Fe₂O₃-promoted ZrO₂ catalysts were prepared by the impregnation method. Fe₂O₃-promoted ZrO₂ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt.%, indicating good dispersion of nickel sulfate on the surface of Fe₂O₃–ZrO₂. The addition of nickel sulfate (or Fe₂O₃) to ZrO₂ shifted the phase transition of ZrO₂ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or Fe₂O₃) and ZrO₂. 15-NiSO₄/5-Fe₂O₃–ZrO₂ containing 15 wt.% NiSO₄ and 5 mol% Fe₂O₃, and calcined at 500 °C exhibited a maximum catalytic activity for ethylene dimerization. NiSO₄/Fe₂O₃–ZrO₂ catalysts was very effective for ethylene dimerization even at room temperature, but Fe₂O₃–ZrO₂ without NiSO₄ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of Fe₂O₃ up to 5 mol% enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between Fe₂O₃ and ZrO₂ and due to consequent formation of Fe–O–Zr bond.     

Damage resistance and R-curve behavior of multilayer Al2O3/SiC ceramics

Damage resistance and R-curve behavior of multilayer Al₂O₃/SiC ceramics were evaluated in bending by the indentation-strength and the single-edge-notched-beam methods. Due to the crack deflection at the Al₂O₃/SiC interfaces, a plateau indentation strength response was achieved, suggesting an exceptional resistance to contact-induced damage. Moreover, fracture toughness was observed to increase from 8.0 to 15.5 MPa m^1/2 with increasing notch depth from 0.5 to 2.0 mm, indicative of a strong R-curve behavior.     

Low-temperature sintering of 0.85CaWO4–0.15LaNbO4 ceramics

Microwave dielectric properties of 0.85CaWO₄–0.15LaNbO₄ (CWLN) ceramics were investigated as a function of H₃BO₃, Li₂CO₃ content and sintering temperature. With the co-addition of 3.0 wt.% H₃BO₃–1.0 wt.% Li₂CO₃, the sintering temperature could be effectively reduced from 1150 °C for pure CWLN ceramics to 900 °C without any degradation of dielectric properties. These results are due to the enhancement of the sinterability of CWLN by liquid phase sintering. For the specimens with H₃BO₃–Li₂CO₃ sintered at 900 °C for 3 h, the dielectric constant (K) did not changed remarkably. However, the quality factor (Qf) and the temperature coefficient of resonant frequency (TCF) increased up to y = 1.0 of 3.0 wt.% H₃BO₃–y wt.% Li₂CO₃, and then decreased due to the formation of the secondary phases. Typically, K of 11.8, Qf of 45,200 GHz and TCF of −23.1 ppm/°C were obtained for the specimens of CWLN with 3.0 wt.% H₃BO₃–1.0 wt.% Li₂CO₃ sintered at 900 °C for 3 h.     

Microstructure and properties of (SiC, TiB2)/B4C composites by reaction hot pressing

(SiC, TiB₂)/B₄C composites were fabricated by reactive hot-pressing B₄C, Si₃N₄, -SiC and TiC powders, with (Al₂O₃ + Y₂O₃) as sintering additives. According to the thermodynamics principles, the possible reaction equations and the reaction products for the system were determined. By means of XRD, SEM of surface thermally etched and TEM the phase composition was determined. It was shown that the phase composition of sintered body was B₄C, -SiC, BN and TiB₂, and the matrix was B₄C and -SiC. The typical values of hardness, bending strength, fracture toughness and the relative density of the composites can reach HRA 88.6, 554 MPa, 5.6 MPa m^1/2 and 95.6%, respectively. Furthermore, the microstructures of the composites were analyzed by TEM, SEM and energy spectrum methods. The results show the presence of laminated structure and a clubbed frame dispersion phase and bunchy dispersion phase among the matrix. Some intragranular structures were also found in the B₄C grains. Microstructural analysis indicates that the new formed phase, uniform and fine grains, and the layered and clubbed structure play an important role in improving the properties of the composites. Fractography and crack propagation suggest that crack deflection and crack bridging are the possible toughening mechanisms.