Crystallization characteristics of intercalated poly(L‐lactide)/organo‐modified montmorillonite hybrids

The crystallization behavior of intercalated Poly(L ‐lactide) (PLLA)/organo‐modified montmorillonite hybrids has been investigated in term of growth of spherulites and bulk crystallization. The PLLA hybrids were prepared via melt‐compounding between PLLA and montmorillonite organo‐modified (organoclay) with two different types of ammonium salts: trimethyl octadecyl‐ or bis(4‐hydroxy butyl) methyl octadecyl ammonium salts. The nucleation rate of PLLA crystallites is slightly enhanced by natural clay, while reduced by organoclay due to the shielding effect and/or miscibility between surfactants of clays and PLLA chains. The incorporation of small amount of organoclay in PLLA matrix shows a tendency to reduce slightly the growth rate and the overall crystallization rate of PLLA crystallites. The secondary nucleation theory was utilized to discuss the crystallization behavior of these hybrids. POLYM. ENG. SCI., 46:39–46, 2006. © 2005 Society of Plastics Engineers     

Effect of zinc phenylphosphonate on the crystallization behavior of poly(l‐lactide)

The effect of zinc phenylphosphonate (PPZn) on the crystallization behavior of poly(l ‐lactide) (PLLA) was investigated using differential scanning calorimetry (DSC) and Polarized Optical Microscopy (POM) measurements. The non‐isothermal cold crystallization results showed that the addition of PPZn obviously decreased the cold crystallization temperature of PLLA and increased the degree of crystallinity of PLLA. The isothermal crystallization kinetics results showed that the crystallization rate of PLLA with small amount of PPZn was much higher than that of neat PLLA, and the half‐time (t_1/2) of PLLA/PPZn sample is far less than that of neat PLLA. As an effective nucleating agent, PPZn particles had also some influence on nucleation mechanism and crystal growth of PLLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2744–2752, 2013     

Crystallization kinetics of poly(L‐lactide)/carbonated hydroxyapatite nanocomposite microspheres

Microspheres consisting of carbonated hydroxyapatite (CHAp) nanoparticles and poly(L ‐lactide) (PLLA) have been fabricated for use in the construction of osetoconductive bone tissue engineering scaffolds by selective laser sintering (SLS). In SLS, PLLA polymer melts and crystallizes. It is therefore necessary to study the crystallization kinetics of PLLA/CHAp nanocomposites. The effects of 10 wt% CHAp nanoparticles on the isothermal and nonisothermal crystallization behavior of PLLA matrix were studied, using neat PLLA for comparisons. The Avrami equation was successfully applied for the analysis of isothermal crystallization kinetics. Using the Lauritzen‐Hoffman theory, the transition temperature from crystallization Regime II to Regime III was found to be around 120°C for both neat PLLA and PLLA/CHAp nanocomposite. The combined Avrami‐Ozawa equation was used to analyze the nonisothermal crystallization process, and it was found that the Ozawa exponent was equal to the Avrami exponent for neat PLLA and PLLA/CHAp nanocomposite, respectively. The effective activation energy as a function of the relative crystallinity and temperature for neat PLLA and PLLA/CHAp nanocomposite under the nonisothermal crystallization condition was obtained by using the Friedman differential isoconversion method. The Lauritzen‐Hoffman parameters were also determined from the nonisothermal crystallization data by using the Vyazovkin‐Sbirrazzuoli equation. CHAp nanoparticles in the composite acted as an efficient nucleating agent, enhancing the nucleation rate but at the same time reducing the spherulite growth rate. This investigation has provided significant insights into the crystallization behavior of PLLA/CHAp nanocomposites, and the results obtained are very useful for making good quality PLLA/CHAp scaffolds through SLS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Non‐isothermal crystallization of poly(ethylene oxide)/silver nanoplate composites

The non‐isothermal crystallization of poly(ethylene oxide) (PEO)/silver nanoplate composites was studied using differential scanning calorimetry. The non‐isothermal crystallization was analyzed by combining the Avrami and Ozawa equations. It was found that the Avrami exponent for neat PEO ranges from 2.51 to 2.53, whereas it ranges from 2.54 to 3.16 for its composites, indicating that the spherical crystal morphology does not change with the addition of nanoplates. However, the rate determination of crystal growth transfers from diffusion to nucleation. The crystallization half‐time showed an increase with the addition of silver nanoplates in PEO, indicating that the overall crystallization rate of PEO decreases with the addition of nanoplates. However, the nucleation activity is larger than unity in the composites and the value increases with an increase in the nanoplate content. This behavior implies that the nanoplates act as anti‐nucleating agents to hinder nucleation. Copyright © 2011 Society of Chemical Industry     

Preparation and characteristics of a novel nano‐sized calcium carbonate (nano‐CaCo3)‐supported nucleating agent of poly(L‐lactide)

Nano‐sized calcium carbonate (nano‐CaCO₃)‐supported nucleating agent for poly(L ‐lactide) (PLLA) was prepared by supporting calcium phenylphosphonate (PPCa) on nano‐CaCO₃ surface. The thermal properties of phenylphosphonic acid (PPOA) and nano‐CaCO₃‐supported nucleating agent and its dispersion in PLLA matrix were investigated by differential scanning calorimetry and field emission scanning electron microscopy. The results indicated that the formation of nucleating agent supported on nano‐CaCO₃ was attributed to the chemical reaction between nano‐CaCO₃ and PPOA. The nano‐CaCO₃‐supported nucleating agents were dispersed evenly in the PLLA matrix even with 5 wt% loading. The supported nucleating agent was added to PLLA to examine its nucleating ability for PLLA. The results of the investigation showed that the nano‐CaCO₃‐supported nucleating agent exhibited higher nucleation ability compared to PPCa nucleating agent. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/clay nanocomposites

The preparation and properties of nanocomposites, consisting of a poly(3‐Hydroxybutyrate‐co‐3‐hydroxyvalerate) and an organophilic clay are described. The effect of organophilic clay on the crystallization behavior of (PHBV) was studied. A differential scanning calorimeter (DSC) was used to monitor the energy of the crystallization process from the melt. During the crystallization process from the melt, the organophilic clay led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of organophilic clay caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation, and growth of the PHBV crystals and the increase caused by a small quantity of clay is move effective than that large one. The equilibrium melting temperature of PHBV was determined as 186°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. The mechanical test shows that the tensile strength of hybrid increased to 35.6 MPa, which is about 32% higher than that of the original PHBV with the incorporation of 3 wt % clay, and the tensile modulus was also increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 655–661, 2004     

Enhancing crystallization rate and melt strength of PLLA with four‐arm PLLA grafted silica: The effect of molecular weight of the grafting PLLA chains

To improve the crystallization rate and melt strength of polylactide (PLLA), nano‐size amino silica grafted by four‐arm PLLA (4A‐PLLA) with different molecular weight was synthesized. ¹H nuclear magnetic resonance proved that 4A‐PLLA had been grafted onto the surface of SiO₂ successfully, and the grafting ratios and the degradation behaviors of the grafted SiO₂ nanoparticles (g‐SiO₂) were studied. When the grafted silica was introduced into PLLA matrix, the crystallization rate and melt strength of composites were found to be improved and the length of grafted chain played an important role. The extension rheology indicated that long grafted 4A‐PLLA on the surface of SiO₂ was more efficient in enhancing the elongational viscosity of PLLA, owing to the stronger interactions between the grafted chains and the matrix. The crystallization behavior of ungrafted silica filled composite was similar to that of neat PLA, while g‐SiO₂ played a role of nucleating agent. The crystallinities and the crystallization rates of the composites depended on the content of g‐SiO₂ and the grafted chain length of 4A‐PLLA, especially the latter. Longer grafted chain acted as nucleation site in the matrix and significantly improved the crystallization behaviors of PLLA. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45675.     

Nonisothermal crystallization behavior and crystals morphology of poly(trimethylene terephthalate)/nano‐calcium carbonate composites

Nonisothermal crystallization behavior and crystal morphology of poly(trimethylene terephthalate) (PTT) composites filled with modified nano‐calcium carbonate (CaCO₃) had been investigated by using differential scanning calorimetry and polarized optical microscopy. The modified Avrami equation and Ozawa theory were used to investigate the nonisothermal crystallization, respectively. The particles of nano‐CaCO₃, acting as a nucleation agent in composites, accelerated the crystallization rate by decreasing the half‐time of crystallization or increasing the parameters of Z_c and K(T). Moreover, the nano‐composite with 2 wt% nano‐CaCO₃ exhibited the highest crystallization rate. The Avrami and the Ozawa exponents, n and m of the nano‐composites, were higher than those of neat PTT, suggesting more complicated interaction between molecular chains and the nanoparticles that cause the changes of the nucleation mode and the crystal growth dimension. The effective activation energy calculated from the Friedman formula was reduced as nano‐CaCO₃ content increased, suggesting that the nano‐CaCO₃ made the molecular chains of PTT easier to crystallize during the nonisothermal crystallization process. The optical micrographs showed that much smaller or less perfect crystals were formed in composites because of the presence of the nano‐CaCO₃ particles. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Crystallization of poly(3‐hydroxybutyrate) with stereocomplexed polylactide as biodegradable nucleation agent

Crystallization kinetics behavior and morphology of poly(3‐hydroxybutyrate) (PHB) blended with of 2–10 wt% loadings of poly(L ‐ and D ‐lactic acid) (PLLA and PDLA) stereocomplex crystallites, as biodegradable nucleating agents, were studied using differential scanning calorimetry, polarizing‐light optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). Blending PLLA with PDLA at 1:1 weight ratio led to formation of stereocomplexed PLA (sc‐PLA), which was incorporated as small crystalline nuclei into PHB for investigating melt‐crystallization kinetics. The Avrami equation was used to analyze the isothermal crystallization of PHB. The stereocomplexed crystallites acted as nucleation sites in blends and accelerated the crystallization rates of PHB by increasing the crystallization rate constant k and decreasing the half‐time (t_1/2). The PHB crystallization was nucleated most effectively with 10 wt% stereocomplexed crystallites, as evidenced byPOM results. The sc‐PLA complexes (nucleated PHB crystals) exhibit much small spherulite sizes but possess the same crystal cell morphology as that of neat PHB based on the WAXD result. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Influence of clay content on the melting behavior and crystal structure of nonisothermal crystallized poly(L‐lactic acid)/nanocomposites

To study the effect of organophilic clay concentration on nonisothermal crystallization, poly(L ‐lactic acid) (PLLA)/montmorillonite (MMT) nanocomposites were prepared by mixing various amounts of commercial MMT (Cloisite^® 30B) and PLLA. The effect of MMT content on melting behavior and crystal structure of nonisothermal crystallized PLLA/MMT nanocomposites was investigated by differential scanning calorimetry (DSC), small‐angle X‐ray scattering, and wide‐angle X‐ray diffraction (XRD) analyses. The study was focused on the effect of the filler concentration on thermal and structural properties of the nonisothermally crystallized nanocomposite PLLA/MMT. The results obtained have shown that at filler loadings higher than 3 wt %, intercalation of the clay is observed. At lower clay concentrations (1–3 wt %), exfoliation predominates. DSC and XRD analysis data show that the crystallinity of PLLA/MMT composites increases drastically at high clay loadings (5–9 wt %). In these nanocomposites, PLLA crystallizes nonisothermally in an orthorhombic crystal structure, assigned to the α form of PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Cold‐crystallization behavior of poly(L‐lactide)/ACR blend films investigated by in situ FTIR spectroscopy

The cold crystallization behavior of poly (L ‐lactide) (PLLA) blend films modified by small amount of acrylic rubber particles (ACR) have been investigated by in situ Fourier‐transform infrared (FTIR) spectroscopy. During the isothermal cold crystallization, the crystallization rate of PLLA is greatly improved with addition of only 1 wt % ACR. However, for PLLA with 8 wt % ACR, the crystallization rate is slower than that of neat PLLA. The relative crystallinity of PLLA with the addition of 1–5 wt % ACR is obviously higher than that of the neat PLLA. For the PLLA blend film with 3 % ACR, the relative crystallinity reaches a maximum. It was found that the addition of ACR particles below 5% accelerated the cold crystallization nucleation process and made the cold‐crystallization rate of PLLA/ACR be quicker than that of neat PLLA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization behavior and isothermal crystallization kinetics of PLLA blended with ionic liquid, 1‐butyl‐3‐methylimidazolium dibutylphosphate

The crystallization behavior and isothermal crystallization kinetics of neat poly(l ‐lactic acid) (PLLA) and PLLA blended with ionic liquid (IL), 1‐butyl‐3‐methylimidazolium dibutylphosphate, were researched by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WXRD). Similar to the non‐isothermal crystallization behavior of neat PLLA, when PLLA melt was cooled from 200 to 20°C at a cooling rate of 10°C min^?1, no crystallization peak was detected yet with the incorporation of IL. However, the glass transition temperature and cold crystallization temperature of PLLA gradually decreased with the increase of IL content. It can be attributed to the significant plasticizing effect of IL, which improved the chain mobility and cold crystallization ability of PLLA. Isothermal crystallization kinetics was also analyzed by DSC and described by Avrami equation. For neat PLLA and IL/PLLA blends, the Avrami exponent n was almost in the range of 2.5–3.0. It is found that t_1/2 reduced largely, and the crystallization rate constant k increased exponentially with the incorporation of IL. These results show that the IL could accelerate the overall crystallization rate of PLLA due to its plasticizing effect. In addition, the dependences of crystallization rate on crystallization temperature and IL content were discussed in detail according to the results obtained by DSC and POM measurements. It was verified by WXRD that the addition of IL could not change the crystal structure of PLLA matrix. All samples isothermally crystallized at 100°C formed the α‐form crystal. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41308.     

Crystallization behavior and nucleation analysis of poly(l‐lactic acid) with a multiamide nucleating agent

To accelerate the crystallization of poly(L ‐lactic acid) (PLLA) and enhance its crystallization ability, a multiamide nucleator (TMC) was introduced into the PLLA matrix. The thermal characteristics, isothermal and nonisothermal crystallization behavior of pure PLLA and TMC‐nucleated PLLA were investigated by differential scanning calorimetry. The determination of thermal characteristics shows that the addition of TMC can significantly decrease the onset temperature of cold crystallization and meanwhile elevate the total crystallinity of PLLA. For the isothermal crystallization process, it is found that the overall crystallization rate is much faster in TMC‐nucleated PLLA than in pure PLLA and increases as the TMC content is increased, however, the crystal growth form and crystalline structure are not influenced much despite the presence of TMC. In the case of nonisothermal crystallization, the nucleation efficiency and nucleation activity were estimated and the results indicate that excellent nucleation‐promoting effect could be achieved when the weight percentage of TMC is chosen between 0.25% and 0.5%. Polarized optical microscopy observation reveals that the nuclei number of PLLA increases and the spherulite size reduces greatly with the addition of TMC. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Nonisothermal crystallization kinetics of polyamide 6 and ethylene‐co‐butyl acrylate blends

The nonisothermal melt‐crystallization behavior of PA6 and EBA blends at varying EBA content was investigated using differential scanning calorimetry at different scanning rates. Several macrokinetic models such as Avrami, Jeziorny, Ozawa, Liu, Ziabicki, and Tobin were applied to analyze the crystallization behavior thoroughly under nonisothermal conditions. The Avrami and Tobin model predicted that, for pure PA6 and PA6/EBA blends, simultaneous growth of all forms of crystal structures such as fibrillar, disc‐like, and spherulitic proceeds at an increasing nucleation rate. However, when applied to blends for isothermal crystallization, the Avrami model predicted that the crystallization process is diffusion‐controlled for pure PA6 and PA6/EBA blend containing higher content of EBA (50 phr), where the nylon‐6 chains were able to diffuse freely to crystallize under isothermal conditions. Liu model predicted that, at unit crystallization time, a higher cooling rate should be used to obtain a higher degree of crystallinity for both PA6 and PA6/EBA blends. The kinetic crystallizability of PA6 in the blends calculated using Ziabicki's approach varies depending upon the nucleation density and PA6‐rich regions present in the blend compositions. Nucleation activity of the blends estimated by Dobreva and Gutzowa method reveals that the EBA particles are inert at lower concentrations of EBA and do not act as nucleating agent for PA6 molecules in the blends. The activation energy of nonisothermal crystallization, calculated using Augis–Bennett, Kissinger, and Takhor methods indicated that the activation energy is slightly lower for the blends when compared to the neat PA6. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The relationship between solubility and nucleating effect of organic nucleating agent in poly(L-lactic acid)

N,N′-bis(benzoyl) hexanedioic acid dihydrazide (BHAD), and N,N′-bis(benzoyl) terephthalic acid dihydrazide (BTAD) were synthesized as the organic nucleating agents for poly(L-lactic acid) (PLLA). These two organic compounds exhibited different nucleating effect to PLLA. When the concentration was very low, BTAD was able to nucleate PLLA, while BHAD was not. When the concentration was adequate, BHAD showed better nucleating effect than BTAD. The experiments showed that, BHAD had the ability of dissolving into PLLA melt matrix, while BTAD was insoluble in PLLA. The optical microscope images revealed the quite different PLLA crystal morphologies nucleated by BHAD and BTAD. As BTAD could not dissolve in PLLA melt, it only induced a mass of small grain crystals of PLLA, the morphology of which is the same as neat PLLA. BHAD had relatively different nucleation and crystallization behaviors. Upon heating, BHAD could partially or totally dissolve in PLLA melt, which depended on the final heating temperature and its concentration. Upon cooling, BHAD separated from PLLA matrix and formed needle like or dendritic structures. Moreover, totally dissolved BHAD could finally exhibit dendritic structures, which had an excellent nucleation effect to PLLA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46851.     

Nonisothermal crystallization behavior of melt‐intercalated polyethylene‐clay nanocomposites

The influence of nanoclay particles on the nonisothermal crystallization behavior of intercalated polyethylene (PE) prepared by melt‐compounding was investigated. It is observed that the crystallization peak temperature (T_p) of PE/clay nanocomposites is slightly but consistently higher than the neat PE at various cooling rates. The half‐time (t_0.5) for crystallization decreased with increase in clay content, implying the nucleating role of nanoclay particles. The nonisothermal crystallization data are analyzed using the approach of Avrami (Polymer 1971, 12, 150), Ozawa (Polym Eng Sci 1997, 37, 443), and Mo and coworkers (J Res Natl Bur Stand 1956, 57, 217), and the validity of the different kinetic models to the nonisothermal crystallization process of PE/clay nanocomposites is discussed. The approach developed by Mo and coworkers successfully explains the nonisothermal crystallization behavior of PE and PE/clay nanocomposites. The activation energy for nonisothermal crystallization of neat PE and PE/clay nanocomposites is determined using the Kissinger (J Res Natl Bur Stand 1956, 57, 217) method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3809–3818, 2006     

Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Enhanced nonisothermal and isothermal cold crystallization kinetics of biodegradable poly(l‐lactide) by trisilanolisobutyl‐polyhedral oligomeric silsesquioxanes in their nanocomposites

In this work, the nonisothermal and isothermal cold crystallization behaviors of poly(l ‐lactide) (PLLA)/trisilanolisobutyl‐polyhedral oligomeric silsesquioxanes (tsib‐POSS) nanocomposites with low tsib‐POSS contents were fully investigated. For all the samples, the variations of heating rate and the tsib‐POSS loading may influence the nonisothermal cold crystallization of PLLA. During the nonisothermal crystallization kinetics study, the Ozawa equation failed to fit the nonisothermal crystallization process of PLLA, while the Tobin equation could fit it well. For the isothermal crystallization kinetics study, the crystallization rates of all the samples increased with increasing crystallization temperature. The cold crystallization activation energy of PLLA was increased with 1 wt % tsib‐POSS. Moreover, the addition of tsib‐POSS and the increment of tsib‐POSS loading could increase the crystallization rate of PLLA, indicating the nucleating agent effect of tsib‐POSS. However, the crystallization mechanism and crystal structure of PLLA remained unchanged in the nanocomposites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43896.     

Poly(L‐lactide)/Poly(D‐lactide)/clay nanocomposites: Enhanced dispersion,crystallization, mechanical properties,and hydrolytic degradation

Poly(L ‐lactide) (PLLA)/poly(D ‐lactide) (PDLA)/clay nanocomposites are prepared via simple melt blending method at PDLA loadings from 5 to 20 wt%. Formation of the stereocomplex crystals in the nanocomposites is confirmed by differential scanning calorimetry and wide‐angle X‐ray diffraction (WAXD). The internal structure of the nanocomposites has been established by using WAXD and transmission electron microscope analyses. The dispersion of clay in the PLLA/PDLA/clay nanocomposites can be improved as a result of increased intensity of shear during melt blending. The overall crystallization rates are faster in the PLLA/PDLA/clay nanocomposites than in PLLA/clay nanocomposite and increase with an increase in the PDLA loading up to 10 wt%; however, the crystallization mechanism and crystal structure of these nanocomposites remain unchanged despite the presence of PDLA. The storage modulus has been apparently improved in the PLLA/PDLA/clay nanocomposites with respect to PLLA/clay nanocomposite. Moreover, it is found that the hydrolytic degradation rates have been enhanced obviously in the PLLA/PDLA/clay nanocomposites than in PLLA/clay nanocomposite. POLYM. ENG. SCI., 54:914–924, 2014. © 2013 Society of Plastics Engineers     

Poly(l‐lactic acid) with the organic nucleating agent N,N,N′‐tris(1H‐benzotriazole) trimesinic acid acethydrazide: Crystallization and melting behavior

N,N,N′‐Tris(1H‐benzotriazole) trimesinic acid acethydrazide (BD) was synthesized from 1H‐benzotriazole acetohydrazide and trischloride to serve as an organic nucleating agent for the crystallization of poly(l ‐lactic acid) (PLLA). First, the thermogravimetric analysis of BD exhibited a high thermal decomposition temperature; this indicated that BD maybe used as a heterogeneous nucleating agent of PLLA. Then, the effect of BD on the crystallization and melting behavior of PLLA was investigated through differential scanning calorimetry, depolarized light intensity measurements, and wide‐angle X‐ray diffraction. The appearance of a nonisothermal crystallization peak and increases in the glass‐transition temperature and the intensity of the diffraction peak suggested that the presence of BD accelerated the overall PLLA crystallization. Upon cooling at a rate of 1°C/min, the addition of just 0.5 wt % BD to PLLA increased the onset crystallization temperature from 101.4 to 111.3°C, and the nonisothermal crystallization enthalpy increased from 0.1 to 38.6 J/g. The isothermal crystallization behavior showed that the crystallization half‐time of PLLA with 0.5 wt % BD (PLLA/0.5% BD) decreased from 49.9 to 1.1 min at 105°C. However, the equilibrium melting point of PLLA/0.5% BD was lower than that of the pristine PLLA; this resulted from the increasing nucleating density of PLLA. The melting behavior of PLLA/0.5% BD further confirmed that BD improved the crystallization of PLLA, and the double‐melting peaks of PLLA/0.5% BD were assigned to melting–recrystallization. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42402.