首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 588 毫秒
1.
Dual-cure hybrid polymer networks were prepared by sequential thiol–ene photopolymerization followed by thermal ring-opening polymerization of benzoxazines with the aim of increasing the glass transition temperature range of thiol–ene based materials and improving the processibility of polybenzoxazines. The hybrid networks are derived from a multifunctional, dually-polymerizable monomer possessing both bis-“ene” and bis-benzoxazine moieties enabling the formation of two networks through a common constituent monomer when combined with a multifunctional thiol. The photopolymerization kinetics of the thiol–ene reaction were investigated by real-time infrared spectroscopy. Sequential thermal ring-opening polymerization of the benzoxazine moieties incorporated into the thiol–ene network was characterized by FTIR and differential scanning calorimetry. The glass transition of the hybrid material was observed at 150 °C; however, competing thiol–ene (radical-mediated) and thiol–benzoxazine (nucleophilic ring-opening) reactions during the UV cure yield a heterogeneous network structure.  相似文献   

2.
Photoinitiated thiol/ene polymerization was used to crosslink a triblock styrene/butadiene/styrene (SBS) polymer of low vinyl content (8%). The crosslinking process was followed by infrared spectroscopy (loss of unsaturation), insolubilization, swelling, and hardness measurements. The photogenerated thiyl radicals react with both the vinyl and the 2‐butene double bonds of the copolymer. Concentrations of less than 1 wt % in the trifunctional thiol crosslinker and in the acylphosphine oxide photoinitiator proved to be sufficient to create, within 0.5 s, a permanent chemical network in the elastomeric phase. This UV‐curing technology was successfully applied to crosslink rapidly commercial SBS–Kraton® thermoplastic elastomers. It proved also effective in the case of the much less reactive triblock styrene/isoprene/styrene (SIS) polymer which contains no vinyl double bonds. The thiol/ene polymerization was shown to be a much more efficient process to crosslink SBS and SIS thermoplastic elastomers than was the copolymerization of the rubber double bonds with a diacrylate monomer. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1902–1912, 2000  相似文献   

3.
Hybrid thiol‐ene/epoxy coatings were prepared by combining thiol‐ene photo‐curable formulations with epoxy monomers, through a dual UV–thermal curing process. An increase in glass transition temperature and in storage modulus was observed for the hybrid thiol‐ene/epoxy coatings when compared with the pristine thiol‐ene UV‐cured system. Also, the bisphenol A moieties introduced into the hybrid networks during the dual‐curing process induced an increase in thermal stability of the cured materials. It has been demonstrated that the addition of epoxy monomer to the thiol‐ene photo‐curable system is a good strategy to follow in order to improve the final properties of thiol‐ene‐based coatings leading to a wide range of possible applications for the hybrid materials. Copyright © 2010 Society of Chemical Industry  相似文献   

4.
To produce a photocurable thiol‐ene system, unsaturated polyester was prepared from the condensation reaction of ethylene glycol, diethylene glycol, and fumaric acid. Diallyl groups were introduced into the ends of the unsaturated polyester by a sequential condensation reaction. The coating formulation studied contained an equimolar ratio of thiol and vinyl groups of the prepared unsaturated polyester, including 1 wt % Irgacure 184. The curing behaviors of the unsaturated polyester with multifunctional thiols were investigated using real‐time FTIR spectroscopy. The rates of disappearance of thiol and vinyl groups of the unsaturated polyester were similar, demonstrating that there was little free‐radical homopolymerization of the internal fumaric group or the end‐capped vinyl ether group during the photocuring process and that the thiol‐ene reaction is the dominant process. The kinetics of the model compounds demonstrated that the reaction of the terminal allyl double bond with the thiyl radical is faster than that of the internal fumaric double bond in the UV curing of the unsaturated polyester. The storage stability of the thiol‐ene system based on unsaturated polyester was effectively increased by the addition of N‐PAL. The Raman spectra revealed that the presence of a multifunctional thiol (penta 3‐MP4) in the coating formulation increased the degree of surface curing due to the chain‐transfer ability of the thiyl radical. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 342–350, 2005  相似文献   

5.
The photocrosslinking of polyacrylonitrile‐block‐polybutadiene‐block‐polyacrylonitrile (ABA) was shown to proceed within seconds at ambient temperature upon UV exposure in the presence of an acylphosphine oxide photoinitiator. The curing process was followed by infrared spectroscopy, insolubilization, and hardness measurements. Complete insolubilization could not be achieved with the neat ABA rubber because of the poor reactivity of the 2‐butene double bond and the low vinyl content of the polybutadiene chain. The addition of multifunctional acrylate monomers (20 wt %) causes a substantial increase of both the reaction rate and the crosslink density of the polymer, which becomes completely insoluble in toluene in less than 1 s upon UV irradiation. An even greater effect was observed by using small amounts (1 wt %) of a trifunctional thiol crosslinker. Both the thiol and the photoinitiator concentrations were shown to affect the kinetics of the thiol–ene polymerization and the polymer network crosslink density. A direct relationship was found to exist between the swelling degree of the UV‐cured rubber and the interchain molecular weight of the network. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2204–2216, 2001  相似文献   

6.
Tri(ethylene glycol) divinyl ether and the spiro‐orthoester 2‐((allyloxy)methy)‐1,4,6‐trioxospiro[4.4]nonane can be formulated in different ratios and crosslinked by thiol‐ene reactions. The spiro‐orthoester is used as anti‐shrinkage additive, enabling shrinkage reduction of up to 39%. Addition of a radical photoinitiator for the thiol‐ene reaction and a cationic photoinitiator for the double ring‐opening of the spiro‐orthoester enables dual‐curing for application in 3D‐printing. The formulation free of the spiro‐orthoester shows gelation during the printing process and, correspondingly, low resolution. The formulations containing the spiro‐orthoester exhibit higher resolutions in the range of 50 µm. The resins containing mixtures of tri(ethylene glycol) divinyl ether and the spiro‐orthoester show permittivities as high as 104. The dielectric loss factor of the resins is in the range of 0.5–7.6, and the conductivity in the range of 1.3?10?11 to 2.0?10?11 S cm?1. These high‐κ materials can be 3D‐printed by digital light processing for the next generation of electronic materials.  相似文献   

7.
The thermal polymerization of a tetrafunctional thiol (PETMP) and divinyl ether (TEGDVE) was monitored by temperature‐ramping differential scanning calorimetry (DSC) and the effects of inhibitor type and concentration, oxygen inhibition and initiator type were studied. The incorporation of inhibitors was required to produce a stable system at room temperature. Butylated hydroxytoluene (BHT) inhibited polymerization at low temperatures, but was inefficient at high temperatures and polymerization rates, and hence BHT is an ideal stabilizer. In contrast, a nitroxide inhibitor (NO‐67) was a very effective inhibitor and no polymerization occurred until all of the nitroxide was depleted. The presence of oxygen retarded the onset of polymerization but did not change the final conversion significantly. Polymerization with initiators having higher half‐life temperatures shifted the DSC peak to higher temperature because the rate of initiator decomposition and thus initiation was slower. Rheological investigations of the cure at different temperatures revealed that the gel time decreased significantly with increasing cure temperature, and the calculated apparent activation energy for PETMP/TEGDVE was 54 kJ mol?1. Dynamical mechanical thermal analysis of the cured material was undertaken and frequency‐superposed results revealed that the glass transition region of PETMP/TEGDVE/azobisisobutyronitrile was much narrower than that of free‐radically cured dimethacrylate, but was similar to that of an epoxy resin cured with an aromatic diamine. This behaviour could be attributed to PETMP/TEGDVE network homogeneity, or to the less constrained crosslinks in the PETMP/TEGDVE network. Copyright © 2007 Society of Chemical Industry  相似文献   

8.
Photopolymerization kinetics of difunctional thiols with alkenes were studied. Two of the thiols, trans‐1,4‐bis(mercaptomethyl)cyclohexane (CHDMT) and 1,4‐bis(mercaptomethyl)benzene (BDMT) were synthesized. The CHDMT was synthesized via a two step process using potassium thioacetate and hydrochloric acid as reagents. The BDMT was synthesized by a one step process using 1,4‐benzenedimethanebromine with thiourea and potassium hydroxide as reagents. Three types of alkenes (divinyl ether, diallyl ether, and dimethacrylate) were reacted with CHDMT, BDMT or 1,8‐octanedithiol (ODT). The photopolymerization was investigated with and without a photoinitiator. The kinetics of the thiol‐ene photopolymerization was investigated by time‐resolved infrared spectroscopy. It was proposed that the steric hindrance of the cyclohexane (CHDMT) resulted in a lower rate of photopolymerization compared to BDMT and ODT. The vinyl ether (alkene) exhibited the highest activity compared to allyl ether and acrylate which was attributed to a high electron density of the alkene. Incorporation of photoinitiator increased the reaction rate and final conversion of the system, particularly in the ODT system.

  相似文献   


9.
Most thiol–ene systems exhibit shrinkage during cross‐linking, potentially resulting in micro‐cracks and delamination. Oligocyclic monomers like spiroorthoesters (SOEs), on the contrary, show expansion during the ring‐opening polymerization. In this communication, a photocurable thiol–ene system composed of a trifunctional thiol, a bisfunctional allyl‐bisphenol A compound, and an SOE compound bearing one olefin function shows expansion in the range from ?3.07 to +1.70 vol% if the SOE content is increased from 0–30 wt%. Network formation can be accomplished under visible light if a radical as well as a cationic photoinitiator (dual‐cure mechanism) and a sensitizer are used. The elasticity of the cured resin increases upon the addition of the SOE; correspondingly, the glass‐transition temperature shows a (minor) decrease from 16 to 3 °C. A tailor‐made combination of the allyl‐bisphenol A compound (90 wt%) and the SOE (10 wt%) yields networks that are volume‐neutral during curing.  相似文献   

10.
Multilayered thiol‐ene network films with two and three different components were fabricated by spin coating and photopolymerization. The distinctive glass transition temperatures of each layer component were observed at corresponding glass transition regions of each bulk sample. Sub‐Tg aging of 10‐, 21‐, and 32‐layered thiol‐ene films was investigated in terms of enthalpy relaxation. Enthalpy relaxation of each layer component occurred independently and presented the characteristic time and temperature dependency. Overlapped unsymmetrical bell‐shaped enthalpy relaxation distribution having peak maximum at Tg‐10°C of each layer component was observed, resulting in broad distribution of enthalpy relaxation over wide temperature range. In addition, enthalpy relaxation of each layer component in the multilayered thiol‐ene films was significantly accelerated comparing to that of bulk thiol‐ene samples. Dynamic mechanical thermal properties of multilayered thiol‐ene films also showed two and three separated glass transition temperature. However, for 32‐layered thiol‐ene film consisting of three different layer components, glass transition and damping region are overlapped and the width is extended more than 100°C. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013  相似文献   

11.
Thiol‐terminated polysulfides (PS) are cured by mixing with an oxidant, resulting in limited shelf‐ and/or pot‐life, depending on whether formulated as a one‐ or two‐component system. Mixtures of thiol‐ and alkene‐terminated polysulfides offer the potential for an on‐demand curing process through thiol–ene photopolymerization. Thiol end groups of commercial polysulfides, PS‐1 (1000 g/mol) and PS‐2 (3000 g/mol), were converted to alkene by reaction with (meth)allyl bromide. Photopolymerizations were performed by irradiating films of equimolar thiol:ene mixtures at 320–500 nm (30 mW/cm2) in the presence of 5 wt % 2,2‐dimethoxy‐2‐phenyl‐acetophenone (DMPA). Reaction kinetics were measured using real‐time FTIR by monitoring absorbances at 3075 cm?1 (alkene) or 2550 cm?1 (thiol). In the absence of any reactive diluent, mixtures of thiol and alkene polysulfides failed to gel notwithstanding high reaction conversion (>90%). Partial or total replacement of the thiol polysulfide component with pentaerythritol tetrakis(3‐mercaptopropionate) (PETMP) yielded solid elastomeric films and ultimate reaction conversions of 80–96% after 5 min irradiation. Crosshatch adhesion measured on glass, aluminum, and steel was very poor (0B) for (meth)allyl PS‐1/PETMP and poor (2B) for (meth)allyl PS‐2/PETMP without adhesion promoters. (3‐Mercaptopropyl)trimethoxysilane (1 wt %) significantly improved adhesion of (meth)allyl PS‐2/PETMP on all substrates (4B) but yielded no improvement for (meth)allyl‐terminated PS‐1/PETMP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45523.  相似文献   

12.
A study has been made of radiation-induced grafting of vinyl acetate (VAc) on to (tetrafluoroethylene–perfluorovinyl ether) copolymer (PFA). Effects of grafting conditions such as inhibitor and monomer concentrations and irradiation dose on the grafting yield were investigated. In this grafting system, ammonium ferrous sulphate (Mohr′s salt) was added to the monomer-solvent mixture to minimize the homopolymerization of VAc and the most suitable concentration was found to be 2.0 wt%. It was found that the dependence of the initial grafting rate on monomer concentration is of the order 1.5. The degree of grafting tends to level off at high irradiation doses due to the recombination of formed free radicals without initiating graft polymerization. Some properties of the prepared graft copolymer such as swelling behaviour, electrical conductivity, thermal and mechanical properties were also investigated. The electrical conductivity was improved by hydrolysis of poly(vinyl acetate) in the grafted chains to their respective vinyl alcohols. The tensile properties were improved by grafting; however, the elongation percent decreased. The DTA data showed thermal stability of such graft copolymers for temperatures up to 300°C, but stability decreased at higher temperatures.  相似文献   

13.
The continued interest in graft copolymer architectures arises from their unique solution properties and potential for a myriad of applications ranging from drug delivery to adhesives. Poly(vinyl pyrrolidone) (PVP) represents a popular amorphous, water‐soluble polymer used as a polymeric binder in binder jetting additive manufacturing, as fillers in cosmetic products, and for subcutaneous drug delivery systems. This report describes the synthesis of poly(2‐oxazoline) and PVP graft copolymers using a ‘grafting to’ methodology with an efficient thiol–ene ‘click’ reaction. Copolymerization of 2‐methyl‐2‐oxazoline and 2‐(3‐butenyl)‐2‐oxazoline introduced pendent vinyl grafting sites with a predictable absolute number‐average molecular weight. In parallel, reversible addition‐fragmentation chain‐transfer polymerization and subsequent aminolysis yielded well‐defined, oligomeric, thiol‐terminated PVP. Thiol–ene click chemistry enabled the formation of poly(2‐oxazoline)‐graft‐poly(vinyl pyrrolidone) (PMeOx‐g‐PVP) copolymers with varying mole percent grafting sites and PVP graft length. 1H NMR spectroscopy, aqueous SEC with multiangle light scattering (SEC‐MALS), and bromine titrations confirmed chemical structure, and DSC with TGA elucidated thermal transitions. Aqueous SEC‐MALS and 1H NMR spectroscopy also determined absolute number‐ and weight‐average molecular weights and average grafting levels, which revealed optimal reaction conditions. Zero‐shear viscosities of 5 and 10 wt% solutions in deionized water for each graft copolymer compared to their linear analogs demonstrated a significant (ca 31%) decrease in viscosity at the same number‐average molecular weight. This decrease in solution viscosity suggested PMeOx‐g‐PVP copolymers as exceptional alternatives to linear analogs for aqueous‐based, binder jetting additive manufacturing.  相似文献   

14.
Epoxy‐ended hyperbranched polymers (EHPs) have a wide range of applications due to their outstanding performances. Because their microstructures are not positively identified, it is very difficult to ascertain the reinforcing and toughening mechanisms of EHPs and their interface interaction with other matrixes. Controllable synthesis of EHPs with precise degree of branching (DB) remains to be a major challenge. Here, a method for preparing novel nitrogen‐phosphor skeleton epoxy‐ended hyperbranched polymers (NPEHP) with controllable DB by a thiol‐ene Michael addition between thiol‐ended hyperbranched polymers (NPHSH) and glycidyl methacrylate have been firstly reported. NPHSH is synthesized by an esterification between hydroxyl‐ended hyperbranched polymers (NPHOH) and 3‐mercaptopropionic acid. NPHOH is prepared by a thiol‐ene Michael addition between methacrylate group of a monomer and thiol group of linear monomer (AB) and/or branched monomer (AB2). The molar ratio between the AB and AB2 monomers controls the DB of the products. The 1H NMR spectra analysis of NPHOH shows that their experimentally determined DBs are very close to their theoretical values, indicating good controllability of their DBs. The narrow molecular weight distributions of NPHOH, NPHSH, and NPEHP suggest high efficiency of the thiol‐ene Michael addition. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44277.  相似文献   

15.
Differential scanning calorimetry was employed to monitor the thermal polymerization and the photopolymerization kinetics of divinyl ethers by temperature‐ramping and isothermal modes, respectively, with a diphenyl iodonium salt photoinitiator and a thioxanthenone photosensitizer. For thermal polymerization of triethylene glycol divinyl ether (TEGDVE), the peak temperature (i.e. the temperature at the maximum rate) decreased with increased photoinitiator concentration and reduced scanning rate, but the final conversions were all very high (>90%). The exotherm was extremely narrow, suggesting that the reaction was inhibited by a cation scavenger until it was all consumed. The activation energy, determined by the Ozawa method, was 108 ± 7 kJ mol?1. With isothermal photopolymerization of the flexible divinyl ether TEGDVE, the final conversion rose from 30 to 70% with an increase in temperature from 40 to 80 °C. A similar trend but with much lower conversions was observed for a more rigid divinyl ether (bis[4‐(vinyloxy)butyl] terephthalate, BVEBT). For TEGDVE, the activation energy determined from the maximum photocuring rate was 43 ± 4 kJ mol?1, but the activation energy measured at a fixed conversion increased as the conversion rose. A similar value for the activation energy was found for the photocuring of BVEBT. The changes in the dynamic rheology were measured for TEGDVE during its photocuring and the gel point identified. Dynamic mechanical thermal analysis of the cured TEGDVE polymer showed it was a highly crosslinked network with Tg of 23 °C. The vinyl ethers could also be thermally cured by free radicals, but the extent of conversion was less than 33%. Copyright © 2007 Society of Chemical Industry  相似文献   

16.
This report describes the preparation and swelling behaviour of novel hydrogels based on a water‐soluble dimethacrylate monomer (EBisEMA), which is characterized by a relatively high molar mass (Mn ~ 1700 g mol?1) and contains a high proportion of aliphatic ether bonds in its structure. This feature results in moderately crosslinked and flexible polymer networks. Significant differences were observed in degree of swelling, depending on the synthesis method employed to obtain the hydrogels. The equilibrium water sorption of EBisEMA photopolymerized in bulk was 68 wt% while that of EBisEMA photopolymerized in aqueous solution (0.5 g mL?1) was 104 wt%. Thiol–methacrylate hydrogels were prepared by visible light photopolymerization of EBisEMA with a tetrafunctional thiol (PETMP) at various EBisEMA‐to‐PETMP molar ratios. These hydrogels contained unreacted thiol groups because of a faster homopolymerization reaction of EBisEMA. Hydrogels were also prepared in bulk by propylamine‐catalysed Michael addition reaction. No significant differences in swelling were observed between EBisEMA homopolymer and photocured EBisEMA–PETMP copolymer. Conversely, a marked increase in water uptake (110 wt%) was observed in the EBisEMA–PETMP hydrogels prepared by the Michael addition reaction catalysed by propylamine. These trends are explained in terms of a balance between the mass fraction of hydrophilic groups and the crosslinking density of the network. EBisEMA–PETMP hydrogels formulated with thiol in excess showed a noticeable tendency to adhere to diverse substrates, including paper, metals, glass and skin. This feature makes them especially attractive in applications for which adhesion is particularly critical such as dermatological patches. © 2018 Society of Chemical Industry  相似文献   

17.
2‐Hydroxymethyl‐but‐1‐ene‐3‐one [α‐hydroxymethyl methyl vinyl ketone (HMVK)] was synthesized from methyl vinyl ketone using paraformaldehyde and a tertiary amine catalyst. Free‐radical polymerization of this monomer created transparent, tough polymers that were insoluble in organic solvents. HMVK was converted to trimethylsilyl, acetate, and chloride derivatives. When the hydroxyl group was thus protected or removed, all these monomers could be free radically polymerized in bulk to make soluble polymers. The chlorination reaction is complicated by the formation of 1,1‐bischloromethylacetone, which dehydrohalogenated unexpectedly to the desired α‐chloromethyl methyl vinyl ketone. HMVK will self‐condense to an ether dimer in the presence of a catalytic acid. This reagent is capable of crosslinking many alkene monomers through hydrolytically stable ether bonds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 509–516, 2000  相似文献   

18.
A dual‐crosslinked in situ gelling drug delivery scaffold based on dextran (DEX), thiolated serum albumin, and poly(ethylene glycol) (PEG) is presented. Dextran–vinyl sulfone conjugates with varied molecular weight and degrees of substitution are synthesized by controlling the reaction time and temperature with divinyl sulfone. Dextran–human serum albumin (sHSA) hydrogels are prepared using a thiol‐vinyl sulfone Michael addition reaction with thiolated albumin as the crosslinker. Poly(ethylene glycol) dithiol is added as a third component to the crosslinked dextran–human serum albumin hydrogel to facilitate additional crosslinking, and reduce gelation time, while modulating the physicochemical properties of the Dex–sHSA–PEG network. The onset of gelation of the modular three‐component dual‐crosslinked hydrogel network ranges from 45 min to 1.5 h depending on gel constituent concentrations and the gelation temperature (25 or 37 °C). All gels remain stable for over a 25 d period under physiological conditions. In vitro drug release assays show that dual‐crosslinked Dex–sHSA–PEG hydrogels can deliver doxorubicin in a sustained manner over 7 d. Finally, a Tetrazolium‐based assay shows the biocompatible nature of the Dex–sHSA–PEG hydrogels and capacity to deliver doxorubicin successfully to MCF‐7 breast cancer cells.  相似文献   

19.
Real-time FT-NIR spectroscopy was used to monitor the individual monomer photopolymerization kinetics within the hybrid methacrylate/vinyl ether system composed of 2-phenoxyethyl methacrylate and tri(ethylene glycol) methyl vinyl ether. Photopolymerization processing conditions, such as light intensity, photoinitiator type (both free radical and cationic) and initiator ratios and concentrations, that provide preferential direction of polymer formation based on individual monomer photopolymerization kinetics and overall conversion have been evaluated. Single source UV-light irradiation was employed to produce either single or dual-stage hybrid polymerization, validating the potential of one-step, one-pot methodology for initiating stage-curable polymerizations.  相似文献   

20.
Thiol–ene photopolymerization was employed in order to prepare a series of covalently crosslinked bis(phosphonium)‐containing poly(ionic liquid) (PIL) networks. While the counteranion was held constant (NTf2), the structure of the bis(phosphonium)‐containing ‘ene’ monomer was varied in order to explore the breadth of thermal, mechanical and conductive properties available for this system. Towards this end, it was determined that more flexible spacers within the cationic monomer led to PIL networks with lower Tg values and higher conductivities. Most notable was a two‐ to three‐orders‐of‐magnitude increase in ionic conductivity (from 10?9 to 10?6 S cm?1 at 30 °C, 30% relative humidity) when the R group on phosphonium was changed from phenyl to isopropyl. Changing the functional group ratio to off‐stoichiometry also led to a slight increase in conductivity. Although the thermal stability (Td5%) of the phosphonium ionic liquid monomers was found to be significantly higher (>400 °C) than that of analogous imidazolium monomers, this improvement was not observed to directly transfer over to the polymer where a two‐step decomposition pathway was observed. The first step is attributed to the thiol monomer backbone while the second step correlates well with decomposition of the phosphonium portion of the PIL. © 2019 Society of Chemical Industry  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号