首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
The melting behavior of poly(butylene succinate) (PBSU) in miscible blends with poly(ethylene oxide) (PEO), which is a newly found polymer blends of two crystalline polymers by our group, has been investigated by conventional differential scanning calorimetry (DSC). It was found that PBSU showed double melting behavior after isothermal crystallization from the melt under certain crystallization conditions, which was explained by the model of melting, recrystallization and remelting. The influence of the blend composition, crystallization temperature and scanning rate on the melting behavior of PBSU has been studied extensively. With increasing any of the PEO composition, crystallization temperature and scanning rate, the recrystallization of PBSU was inhibited. Furthermore, temperature modulated differential scanning calorimetry (TMDSC) was also employed in this work to investigate the melting behavior of PBSU in PBSU/PEO blends due to its advantage in the separation of exotherms (including crystallization and recrystallization) from reversible meltings (including the melting of the crystals originally existed prior to the DSC scan and the melting of the crystals formed through the recrystallization during the DSC scan). The TMDSC experiments gave a direct evidence of this melting, recrystallization and remelting model to explain the multiple melting behavior of PBSU in PBSU/PEO blends.  相似文献   

2.
Four blends of poly(hydroxybutyrate) (PHB) and poly(butylene succinate) (PBSU), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHB/PBSU ranging from 80/20 to 20/80 by co-dissolving the two polyesters in N,N-dimethylformamide and casting the mixture. Differential scanning calorimetry (DSC) and optical microscopy (OM) were used to probe the miscibility of PHB/PBSU blends. Experimental results indicated that PHB showed some limited miscibility with PBSU for PHB/PBSU 20/80 blend as evidenced by the small change in the glass transition temperature and the depression of the equilibrium melting point temperature of the high melting point component PHB. However, PHB showed immiscibility with PBSU for the other three blends as shown by the existence of unchanged composition independent glass transition temperature and the biphasic melt. Nonisothermal crystallization of PHB/PBSU blends was investigated by DSC using various cooling rates from 2.5 to 10 °C/min. During the nonisothermal crystallization, despite the cooling rates used two crystallization peak temperatures were found for PHB/PBSU 40/60 and 60/40 blends, corresponding to the crystallization of PHB and PBSU, respectively, whereas only one crystallization peak temperature was observed for PHB/PBSU 80/20 and 20/80 blends. However, it was found that after the nonisothermal crystallization the crystals of PHB and PBSU actually co-existed in PHB/PBSU 80/20 and 20/80 blends from the two melting endotherms observed in the subsequent DSC melting traces, corresponding to the melting of PHB and PBSU crystals, respectively. The subsequent melting behavior was also studied after the nonisothermal crystallization. In some cases, double melting behavior was found for both PHB and PBSU, which was influenced by the cooling rates used and the blend composition.  相似文献   

3.
The melting and crystallization behavior and phase morphology of poly(3-hydroxybutyrate) (PHB) and poly(DL-lactide)-co-poly(ethylene glycol) (PELA) blends were studied by DSC, SEM, and polarizing optical microscopy. The melting temperatures of PHB in the blends showed a slight shift, and the melting enthalpy of the blends decreased linearly with the increase of PELA content. The glass transition temperatures of PHB/PELA (60/40), (40/60), and (20/80) blends were found at about 30°C, close to that of the pure PELA component, during DSC heating runs for the original samples and samples after cooling from the melt at a rate of 20°C/min. After a DSC cooling run at a rate of 100°C/min, the blends showed glass transitions in the range of 10–30°C. Uniform distribution of two phases in the blends was observed by SEM. The crystallization of PHB in the blends from both the melt and the glassy state was affected by the PELA component. When crystallized from the melt during the DSC nonisothermal crystallization run at a rate of 20°C/min, the temperatures of crystallization decreased with the increase of PELA content. Compared with pure PHB, the cold crystallization peaks of PHB in the blends shifted to higher temperatures. Well-defined spherulites of PHB were found in both pure PHB and the blends with PHB content of 80 or 60%. The growth of spherulites of PHB in the blends was affected significantly by 60% PELA content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1849–1856, 1997  相似文献   

4.
Poly(ethylene succinate) (PES), poly(butylene succinate) (PBS), and PES‐rich copolyesters were synthesized using an effective catalyst, titanium tetraisopropoxide. PES was blended with minor amounts of PBS for the comparison. The compositions of the copolyesters and the blends were determined from NMR spectra. Their thermal properties were studied using a differential scanning calorimeter (DSC), a temperature modulated DSC (TMDSC), and a thermogravimetric analyzer. No significant difference exists among the thermal stabilities of these polyesters and blends. For the blends, the reversible curves of TMDSC showed a distinct glass‐rubber transition temperature (Tg), however, the variation of the Tg values with the blend compositions was small. Isothermal crystallization kinetics and the melting behavior after crystallization were examined using DSC. Wide‐angle X‐ray diffractograms (WAXD) were obtained for the isothermally crystallized specimens. The results of DSC and WAXD indicate that the blends have a higher degree of crystallinity and a higher melting temperature than those of the corresponding copolymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010  相似文献   

5.
Akira Kaito 《Polymer》2006,47(10):3548-3556
The oriented crystallization of poly[(R)-3-hydroxybutyrate] (PHB) in the miscible blends with poly(vinylidene fluoride) (PVDF) was investigated with various compositions. The PVDF/PHB blend films were prepared by solution casting and subsequent melt-quenching in ice water. Oriented films of the blends were prepared by uniaxially stretching the melt-quenched film at 0 °C in ice water using a hand-operated stretching apparatus. The oriented blend films were heat-treated at a fixed length in order to crystallize PHB in the oriented state. The crystal orientation and the lamellar textures of the obtained samples were studied with wide-angle X-ray diffraction (WAXD), and small-angle X-ray scattering (SAXS), respectively. The SAXS measurements showed that a considerable amount of molecular chains of PHB are excluded from the lamellar stacks of PVDF and exist in the interfibrillar regions in the oriented films of the blends. The cold crystallization of PHB in the interfibrillar region results in the orientation of PHB crystals, and the type of crystal orientation depends upon the composition of the blends. For the PVDF/PHB=4/6-7/3 blends, the crystal a-axis of PHB is highly oriented parallel to the drawing direction and the crystal c-axis (molecular chain axis) in PHB crystals is perpendicular to the drawing direction, i.e. orthogonal to the chain axis of the crystals of PVDF. It is considered that the a-axis orientation is induced by the confinement of crystal growth in the interfibrillar nano-domains. For the PVDF/PHB=2/8-3/7 blends, however, the crystal c-axis of PHB is primarily oriented in the drawing direction, suggesting that the stressed molecular chains of PHB are crystallized with the molecular orientation retained.  相似文献   

6.
Multiple melting behavior was observed in the differential scanning calorimetry (DSC) scans for the isothermally crystallized poly(iminosebacoyl iminodecamethylene) (PA1010) samples. Coexistence of crystal populations with different lamellar thickness in PA1010 was discussed by means of DSC, wide‐angle X‐ray diffraction (WAXD), and small‐angle X‐ray scattering techniques. During crystallization of the polymer, a major lamellar crystal population developed first, which possessed a higher melting temperature. However, a small fraction of the polymer formed minor crystal population with thinner lamellae, which was metastable and, upon post‐annealing, could grow into more stable and thicker lamellae through melting and recrystallization process. Lamellae insertion or stacks would develop during the post‐annealing at a lower temperature for the isothermally crystallized samples; thus, multiple crystal populations with different thickness could be produced. It is the multiple distribution of lamella thickness that gives rise to multiple melting behavior of crystalline polymers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 993–1002, 2000  相似文献   

7.
Blends of two biodegradable semicrystalline polymers, poly(p‐dioxanone) (PPDO) and poly(vinyl alcohol) (PVA) were prepared with different compositions. The thermal stability, phase morphology and thermal behavior of the blends were studied by using thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). From the TGA data, it can be seen that the addition of PVA improves the thermal stability of PPDO. DSC analysis showed that the glass transition temperature (Tg) and the melting temperature (Tm) of PPDO in the blends were nearly constant and equal to the values for neat PPDO, thus suggesting that PPDO and PVA are immiscible. It was found from the SEM images that the blends were phase‐separated, which was consistent with the DSC results. Additionally, non‐isothermal crystallization under controlled cooling rates was explored, and the Ozawa theory was employed to describe the non‐isothermal crystallization kinetics. Copyright © 2006 Society of Chemical Industry  相似文献   

8.
Nanofibers and films of poly(3‐hydroxybutyrate) (PHB)/nylon 3 [poly(β‐alanine) (N3)], PHB/poly(α‐methyl‐β‐alanine) (2mN3), and PHB/poly(β‐methyl‐β‐alanine) (3mN3) blends were prepared by electrospinning and film‐casting techniques, respectively. The miscibility of the blends was studied by Fourier transform infrared spectrometry, differential scanning calorimetry, thermogravimetric analysis, and X‐ray diffraction (XRD). The electrospinnability of the blends was studied by scanning electron microscopy. Some characteristic IR absorption bands of the components in the blends shifted gradually with changes in the compositions. The melting temperature and decomposition temperature of PHB decreased gradually with increasing fractions of N3, 2mN3, and 3mN3. The XRD spectra of all of the blends exhibited peaks with lower intensities compared to those of the neat species. The suppression of PHB crystallinity in the blends after blending was attributed to the disruption of its crystal lattice and the prevention of recrystallization of each component by means of other components and segmental interactions between the components in the amorphous phase. Thermal, spectroscopic, and optical analyses of the polymer blends revealed that the polymers were miscible with good compatibility, and this could have improved the scaffold properties of PHB. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40484.  相似文献   

9.
The miscibility and effect of physical aging on the crystallization behavior of poly(l ‐lactic acid) (PLLA)/poly(3‐hydroxybutyrate) (PHB) blends with a small amount of PHB (≤10 wt%) have been investigated using differential scanning calorimetry and Fourier transform infrared spectroscopy. It is found that the miscibility of PLLA/PHB blends with a very small percentage of PHB can be modulated by varying the molecular weight of the PHB. That is, a PLLA/PHB blend with low‐molecular‐weight PHB is miscible, whereas that with high‐molecular‐weight PHB is immiscible. It is found that physical aging at temperatures far below the glass transition temperature can promote the cold crystallization kinetics of PLLA in PLLA/PHB blends with high‐molecular‐weight PHB rather than in those with low‐molecular‐weight PHB. These findings suggest that the effect of physical aging on the crystallization behavior of the main component in a crystalline/crystalline blend with a small percentage of the second component is strongly dependent on the miscibility of the blend system. Enhanced chain mobility of PLLA in the interface region of PLLA matrix and PHB micro‐domains is proposed to explain the physical aging‐enhanced crystallization rate in immiscible PLLA/PHB blends with high‐molecular‐weight PHB. © 2013 Society of Chemical Industry  相似文献   

10.
Poly(ethylene‐octene) (POE), maleic anhydride grafted poly(ethylene‐octene) (mPOE), and a mixture of POE and mPOE were added to poly(butylene terephthalate) (PBT) to prepare PBT/POE, PBT/mPOE, and PBT/mPOE/POE blends by a twin‐screw extruder. Observation by scanning electron microscopy revealed improved compatibility between PBT and POE in the presence of maleic anhydride groups. The melting behavior and isothermal crystallization kinetics of the blends were studied by wide‐angle X‐ray diffraction and differential scanning calorimeter; the kinetics data was delineated by kinetic models. The addition of POE or mPOE did not affect the melting behavior of PBT in samples quenched in water after blending in an extrude. Subsequent DSC scans of isothermally crystallized PBT and PBT blends exhibited two melting endotherms (TmI and TmII). TmI was the fusion of the crystals grown by normal primary crystallization and TmII was the melting peak of the most perfect crystals after reorganization. The dispersed second phase hindered the crystallization; on the other hand, the well dispersed phases with smaller size enhanced crystallization because of higher nucleation density. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008  相似文献   

11.
The crystallization and melting behavior of poly(ether ether ketone) (PEEK) in blends with poly(aryl ether sulfone) (PES) prepared by melt mixing are investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray scattering (WAXS). The presence of PES is found to have a notable influence on the crystallization behavior of PEEK, especially when present in low concentrations in the PEEK/PES blends. The PEEK crystallization kinetics is retarded in the presence of PES from the melt and in the rubbery state. An analysis of the melt crystallization exotherm shows a slower rate of nucleation and a wider crystallite size distribution of PEEK in the presence of PES, except at low concentrations of PES, where, because of higher miscibility and the tendency of PES to form ordered structures under suitable conditions, a significantly opposite result is observed. The cold crystallization temperature of the blends at low PES concentration is higher then that of pure PEEK, whereas at a higher PES concentration little change is observed. In addition, the decrease in heat of cold crystallization and melting, which is more prevalent in PEEK‐rich compositions than in pure PEEK, shows the reduction in the degree of crystallinity because of the dilution effect of PES. Isothermal cold crystallization studies show that the cold crystallization from the amorphous glass occurs in two stages, corresponding to the mobilization of the PEEK‐rich and PES‐rich phases. The slower rate of crystallization of the PEEK‐rich phase, even in compositions where a pure PEEK phase is observed, indicates that the presence of the immobile PES‐rich phase has a constraining influence on the crystallization of the PEEK‐rich phase, possibly because of the distribution of individual PEEK chains across the two phases. The various crystallization parameters obtained from WAXS analysis show that the basic crystal structure of PEEK remains unaffected in the blend. Further, the slight melting point depression of PEEK at low concentrations of PES, apart from several other morphological reasons, may be due to some specific interactions between the component homopolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2906–2918, 2003  相似文献   

12.
The melting, isothermal and nonisothermal crystallization behaviors of poly(3‐hydroxybutyrate) (PHB) have been studied by means of temperature modulated differential scanning calorimetry (TMDSC) and conventional DSC. Various experimental conditions including isothermal/annealing temperatures (80, 90, 100, 105, 110, 120, 130, and 140°C), cooling rates (2, 5, 10, 20, and 50°C/min) and heating rates (5, 10, 20, 30, 40, and 50°C/min) have been investigated. The lower endothermic peak (Tm1) representing the original crystals prior to DSC scan, while the higher one (Tm2) is attributed to the melting of the crystals formed by recrystallization. Thermomechanical analysis (TMA) was used to evaluate the original melting temperature (Tmelt) and glass transition temperature (Tg) as comparison to DSC analysis. The multiple melting phenomenon was ascribed to the melting‐recrystallization‐remelting mechanism of the crystallites with lower thermal stability showing at Tm1. Different models (Avrami, Jeziorny‐modified‐Avrami, Liu and Mo, and Ozawa model) were utilized to describe the crystallization kinetics. It was found that Liu and Mo's analysis and Jeziorny‐modified‐Avrami model were successful to explain the nonisothermal crystallization kinetic of PHB. The activation energies were estimated in both isothermal and nonisothermal crystallization process, which were 102 and 116 kJ/mol in respective condition. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42412.  相似文献   

13.
The miscibility, thermal behaviour, morphology and mechanical properties of poly[(R)‐3‐hydroxybutyrate] (PHB) with poly(γ‐benzyl‐L ‐glutamate) (PBLG) are investigated by means of differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and tensile tests. The DSC results show that PHB and PBLG are immiscible in the melt state. Such immiscibility also exists in the amorphous state due to a clear two‐phase separated structure observed by SEM measurements. The blend samples with different thermal history, namely as original and melt samples separately, display differences in thermal behaviour such as the DSC scan profile, the crystallinity and the melting temperature of PHB. The crystallization of PHB both from the molten state and the amorphous state is retarded on addition of the second component. The SEM measurements reveal that a phase inversion occurs between the PHB/PBLG (60/40) and PHB/PBLG (40/60) blends. Except for the PHB/PBLG (40/60) blend, a microphase separated structure is observed for all blend compositions. The mechanical properties vary considerably with blend composition. Compared with pure components, the PHB/PBLG (20/80) blend shows a certain improvement in mechanical properties. © 2001 Society of Chemical Industry  相似文献   

14.
The subsequent melting behaviour of poly(butylene succinate) (PBSU) and poly(ethylene succinate) (PES) was investigated using DSC and temperature modulated DSC (TMDSC) after they finished nonisothermal crystallization from the melt. PBSU exhibited two melting endotherms in the DSC traces upon heating to the melt, which was ascribed to the melting and recrystallization mechanism. However, one melting endotherm with one shoulder and one crystallization exotherm just prior to the melting endotherm were found for PES. The crystallization exotherm was ascribed to the recrystallization of the melt of the crystallites with low thermal stability, and the shoulder was considered to be the melting endotherm of the crystallites with high thermal stability. The final melting endotherm was ascribed to the melting of the crystallites formed through the reorganization of the crystallites with high thermal stability during the DSC heating process. TMDSC experiments gave the direct evidences to support the proposed models to explain the melting behaviour of PBSU and PES crystallized nonisothermally from the melt.  相似文献   

15.
The crystal structure and morphology of poly(ether ether ketone) (PEEK) was investigated using standard differential scanning calorimetry (DSC), flash DSC, optical microscopy, atomic force microscopy, and small angle X-ray scattering tools. The flash DSC results suggested that the double melting peaks phenomenon observed in conventional DSC work originated from the reorganization of PEEK crystals, which was due to the much faster recrystallization rate of PEEK than the DSC heating and cooling rate. A refined crystallization model to describe PEEK crystal structure formation was proposed. The refined crystallization model could help reconcile the discrepancy found between the bulk crystallinity measured by DSC and the linear crystallinity obtained from SAXS experiments by taking into account possible variation in crystal perfection within the lamellar structure. Simplified molecular dynamic modeling was carried out to support this model. Implications of the above findings to the fundamental understanding of structure–property relationships in PEEK were discussed.  相似文献   

16.
The crystallization and melting behavior of a series of poly(1,1-dimethysilacyclobutane) (PDMSB) samples accessible via living anionic polymerization protocols with different molar masses were studied by differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS) and X-ray diffraction (XRD). It has been found that in the cooling process only one crystallization exotherm was observed by using DSC, but in subsequent heating two clear endotherms appeared. DSC measurements additionally revealed that there will be two melting peaks when the isothermal crystallization temperature, Tc, is low enough, but only one melting peak could be obtained when Tc is high. The value of the lower melting peak Tm1 increased with Tc, showing the increase of lamella thickness due to increase of Tc, which was also evidenced by using SAXS measurements. However, the value of the higher melting peak Tm2 stayed almost constant with Tc. XRD analysis showed that there is only one crystal form independent of Tc. While SAXS results revealed only one long range order, indicating this multiple endotherms phenomenon was caused by the recrystallization process during heating, but not isothermal thickening and thinning process as observed for e.g. poly(ethylene oxide)s (PEOs) with low molar masses. Heating rate dependent DSC experiments showed that there are two recrystallization processes with different time scales. The recrystallization at low temperature always showed up independent of heating rate while the recrystallization at high temperature showed up only when the heating rate was very low. This interesting phenomenon was explained by the different energy barrier for the recrystallization process at low and high temperature as shown by in situ SAXS measurements during heating.  相似文献   

17.
Yun Hu  Jianming Zhang  Isao Noda 《Polymer》2008,49(19):4204-4210
The miscibility, crystallization and subsequent melting behavior in binary biodegradable polymer blends of poly(l-lactic acid) (PLLA) and low molecular weight poly(3-hydroxybutyrate) (PHB) have been investigated by differential scanning calorimetry (DSC), Fourier-transform infrared (FTIR) spectroscopy, and wide-angle X-ray diffraction (WAXD). DSC analysis results indicted that PLLA showed no miscibility with high molecular weight PHB (Mw = 650,000 g mol−1) in the 80/20, 60/40, 40/60, 20/80 composition range of the PHB/PLLA blends. On the other hand, it showed some limited miscibility with low molecular weight PHB (Mw = 5000 g mol−1) when the PHB content was below 25%, as evidenced by small changes in the glass transition temperature of PLLA. The partial miscibility was further supported by changes of cold-crystallization behavior of PLLA in the blends. During the nonisothermal crystallization, it was found that the addition of a small amount of PHB up to 30% made the cold-crystallization of PLLA occur in the lower temperature. Meanwhile, the crystallization of PHB and PLLA was observed in the heating process by monitoring characteristic IR bands of each component for the low molecular weight PHB/PLLA 20/80 and 30/70 blends. The temperature-dependent IR and WAXD results also revealed that for PLLA component crystallization, the disorder (α′) phase of PLLA was produced, and that the α′ phase changed to the order (α) phase just prior to the melting point.  相似文献   

18.
The miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) (PEO/PVA) blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarizing optical microscopy. Because the glass‐transition temperature of PVA was near the melting point of PEO crystalline, an uncommon DSC procedure was used to determine the glass‐transition temperature of the PVA‐rich phase. From the DSC and DMA results, two glass‐transition temperatures, which corresponded to the PEO‐rich phase and the PVA‐rich phase, were observed. It was an important criterion to indicate that a blend was immiscible. It was also found that the preparation method of samples influenced the morphology and crystallization behaviors of PEO/PVA blends. The domain size of the disperse phase (PVA‐rich) for the solution‐cast blends was much larger than that for the coprecipitated blends. The crystallinity, spherulitic morphology, and isothermal crystallization behavior of PEO in the solution‐cast blends were similar to those of the neat PEO. On the contrary, these properties in the coprecipitated blends were different from those of the neat PEO. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1562–1568, 2004  相似文献   

19.
Binary blends of poly(lactic acid) (PLA) and poly(propylene carbonate) (PPC) were found to display a peculiar crystallization kinetics. The two biodegradable polymers were blended by melt mixing, to obtain binary blends at various compositions. Temperature‐modulated calorimetry and dynamic‐mechanical analysis indicated that the blend components are partially miscible, and display two separate glass transitions, at temperatures intermediate to those of the plain polymers. Electron microscopy analysis disclosed the morphology of PLA/PPC blends, made of PPC‐rich particles finely dispersed within the PLA‐rich matrix. The possible establishment of interactions between the functional groups of the two polymers upon melt mixing has been hypothesized as the reason for partial miscibility and compatibility of the two biodegradable polymers. The PLA/PPC blends display good mechanical properties, with enhanced performance at rupture compared with plain PLA. Most importantly, the addition of PPC affects also the crystallization kinetics of PLA, since the more mobile PPC chains favor diffusion of the stiffer PLA chain segments towards the growing crystals, which fastens the spherulite growth rate of PLA. Such positive influence of an amorphous polymer on crystal growth rate has been demonstrated here for the first time in blends that display phase‐separation in the melt. POLYM. ENG. SCI., 55:2698–2705, 2015. © 2015 Society of Plastics Engineers  相似文献   

20.
Blending of microbial polyester poly(3‐hydroxybutyrate) (PHB) with various dendritic polyester oligomers or dendrimers was achieved by solution casting to improve the film forming ability of PHB. Films of the blends were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron micrograph (SEM), and Fourier transform infrared spectroscopy (FTIR). It was revealed that there were mainly two types of interactions in the blending system: the plasticizing or lubricating effect of the low melting spherical dendrimers molecules improved the polymer chain mobility through the suppression of PHB crystallization in the blends; The dendrimers also functioned as crosslinking agents or antiplasticizing agents via weak hydrogen bonding to enhance the overall intermolecular interactions which decrease the chain mobility and thus cause the increase of glass transition temperature (Tg) of PHB. TGA results concluded that incorporating the dendrimers could retard the thermal decomposition of PHB and enhanced its thermal stability accordingly. With the above blend processes, the so‐obtained PHB possessed better film forming ability and even patterned surface structures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3782–3790, 2006  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号