Flexible electrochromic device based on poly (3,4-(2,2-dimethylpropylenedioxy)thiophene)

In this study, the design, fabrication and characterization of a flexible electrochromic device based on indium tin oxide (ITO) coated polyethylene terephthalate (PET) plastic is discussed. The working electrochromic material film was poly (3,4-(2,2-dimethylpropylenedioxy)thiophene) (PProDOT-Me₂), while the counter layer of the device was vanadium oxide titanium oxide (V₂O₅/TiO₂) composite film, which serves as an ion storage layer. A solution type electrolyte was used as the ionic transport layer and was sandwiched between the working and counter layers. The device exhibited tuneable light transmittance between transparent and deep blue color, with a maximum contrast ratio at 580 nm wavelength. Other important properties, such as switching speed, life time, and coloration efficiency have been improved.     

Matched‐dual‐polymer electrochromic lenses,using new cathodically coloring conducting polymers,with exceptional performance and incorporated into automated sunglasses

Reported are syntheses of several new monomer precursors of cathodically coloring conducting polymers (CPs), based on a propylene dioxythiophene skeleton. These are shown to yield CPs—both as homopolymers and as copolymers—that are nearly “perfectly” matched electrochemically and electrochromically with a set of anodically coloring poly(aromatic amines), for use in dual‐polymer electrochromic lenses. Resulting dual‐polymer electrochromic lenses display very high light/dark contrast (typically up to 70/7% or 50/0.5% Transmission (integrated over visible spectrum, vs. air reference), Haze < 2%, very high cyclability (> 10 K cycles), multiyear shelf life, appealing transparent to dark‐blue‐black transition, and excellent optical memory. Dramatic lowering of switching time, from 8 to < 1 s, is demonstrated using unique applied‐potential algorithm resident on inexpensive Microcontroller chip. Working, practical dual‐polymer electrochromic spectacles are demonstrated with electrochromic lenses retrofitted to spectacles meeting ANSI Z87.1, GL‐PD 10–12 (U.S. military) specifications. These incorporate photosensor, rechargeable Li battery, Microcontroller, allow for automated operation. Ab‐initio‐design spectacles, also conforming to above specifications, are also demonstrated, with components seamlessly hidden within frame. To the best of our knowledge, the electrochromic lenses and sunglasses reported herein represent the best visible‐region electrochromic performance for dual‐polymer CP electrochromic systems to date and the first practical implementation in working sunglasses. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41043.     

Synthesis and characterization of light‐absorbing cyclopentadithiophene‐based donor–acceptor copolymers

Cyclopentadithiophene and benzothiadiazole based donor–acceptor polymers are fast emerging as the most promising class of materials for organic solar cells. Here we report on a series of Cyclopentadithiophene and benzothiadiazole based conjugated polymers, namely poly[4,7‐bis(4,4‐dioctyl‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene‐2‐yl)benzo[1,2,5]thiadiazole] (P1), poly[4,7‐bis(4,4‐dioctyl‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene‐2‐yl)benzo[1,2,5]thiadiazole‐alt‐9‐(heptadecan‐9‐yl)‐2,7‐bis(4,4,5,5‐tetramethyl)‐1,3,2‐dioxaborolan‐2‐yl)‐9H‐carbazole] (P2) and poly[4,7‐bis(4,4‐dioctyl‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene‐2‐yl)benzo[1,2,5]thiadiazole‐alt‐5,11‐bis(2‐hexyldecyl)‐3,9‐bis(4,4,5,5‐tetramethyl)‐1,3,2‐dioxaborolan‐2‐yl)‐5,11‐dihydroindolo[3,2‐b]carbazole] (P3), with alternating donor and acceptor units and discuss their photophysical and electrochemical properties. Stille coupling of 2‐tributylstannyl‐4,4‐dioctylcyclopenta[2,1‐b:3,4‐b′]dithiophene with 4,7‐dibromobenzo[1,2,5]thiadiazole generated the alternating donor–acceptor monomer 4,7‐bis(4,4‐dioctyl‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene‐2‐yl)benzo[1,2,5]thiadiazole (CPDT‐BT‐CPDT). Homopolymer P1 of CPDT‐BT‐CPDT was synthesized by oxidative polymerization using FeCl₃. Copolymers P2 and P3 were synthesized by palladium‐catalysed Suzuki polycondensation. The synthesized polymers showed good solubility in common organic solvents, and UV‐visible measurements showed that the absorption maxima of the polymers lie in the range 624 to 670 nm. The energy gaps of these polymers were found to lie in the range 1.29 to 1.50 eV. Gel permeation chromatography measurements against polystyrene standards showed the number‐average molecular weight to be in the range (2.2–6.0) × 10⁴ g mol^?1. Thermogravimetric analysis showed the polymers to possess high thermal stability. A preliminary study of photodiode devices prepared using polymers P1, P2 and P3 when blended with the PC₇₁BM electron acceptor found that P2 is the optimum chemical structure for pursuing further device optimization.© 2015 Society of Chemical Industry     

Synthesis and nonlinear optical properties of a novel polyurethane containing cyanovinylthiophene with enhanced thermal stability of dipole alignment for electro‐optic applications

Stabilization of electrically induced dipole alignment is one of the important criteria in the development of nonlinear optical (NLO) polymers for electro‐optic device applications. Polyurethanes for NLO applications have attracted attention because of their high thermal stability due to hydrogen bonding. In the work reported here, we designed and synthesized a new type of NLO polyurethane, in which the pendant NLO chromophores are part of the polymer backbone. This mid‐type NLO polymer is expected to have the merits of both main‐chain and side‐chain NLO polymers, namely stable dipole alignment and good solubility. 1‐[3,4‐Di‐(2‐hydroxyethoxy)phenyl]‐2‐(2‐thienyl)ethene was prepared and condensed with 3,3′‐dimethoxy‐4,4′‐biphenylenediisocyanate to yield a polyurethane. This polyurethane was reacted with tetracyanoethylene to give a novel Y‐type polyurethane (7) containing 1‐(3,4‐dioxyphenyl)‐2‐[5‐(1,2,2‐tricyanovinyl)‐2‐thienyl]ethenes as NLO chromophores, which constitute part of the polymer backbone. Polyurethane 7 is soluble in common organic solvents such as N,N‐dimethylformamide and dimethylsulfoxide. It shows a thermal stability up to 280 °C from thermogravimetric analysis with a glass transition temperature obtained from differential scanning calorimetry of ca 162 °C. The second harmonic generation (SHG) coefficient (d₃₃) of a poled polymer film of he polyurethane at 1560 nm fundamental wavelength is ca 1.11 × 10^?18 C. Polymer 7 exhibits an enhanced thermal stability and no significant SHG decay is observed below 150 °C, which is acceptable for NLO device applications. Copyright © 2009 Society of Chemical Industry     

Electroluminescence and photovoltaic properties of poly(p‐phenylene vinylene) derivatives with dendritic pendants

A copolymer of dendronized poly(p‐phenylene vinylene) (PPV), poly{2‐[3′,5′‐bis (2′‐ethylhexyloxy) bnenzyloxy]‐1,4‐phenylene vinylene}‐co‐poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene] (BE‐co‐MEH–PPV), was synthesized with the Gilch route to improve the electroluminescence and photovoltaic properties of the dendronized PPV homopolymer. The polymer was characterized by ultraviolet–visible absorption spectroscopy, photoluminescence spectroscopy, and electrochemical cyclic voltammetry and compared with the homopolymers poly{2‐[3′, 5′‐bis(2‐ethylhexyloxy) benzyloxy‐1,4‐phenylene vinylene} (BE–PPV) and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH–PPV). Polymer light‐emitting diodes based on the polymers with the configuration of indium tin oxide (ITO)/poly(3,4‐ethylene dioxythiophene) : poly(styrene sulfonate) (PEDOT : PSS)/polymer/Ca/Al were fabricated. The electroluminescence efficiency of BE‐co‐MEH–PPV reached 1.64 cd/A, which was much higher than that of BE–PPV (0.68 cd/A) and a little higher than that of MEH–PPV (1.59 cd/A). Photovoltaic properties of the polymer were studied with the device configuration of ITO/PEDOT : PSS/polymer : [6,6J‐phenyl‐C₆₁‐butyric acid methyl ester] (PCBM)/Mg/Al. The power conversion efficiency of the device based on the blend of BE‐co‐MEH–PPV and PCBM with a weight ratio of 1 : 3 reached 1.41% under the illumination of air mass 1.5 (AM1.5) (80 mW/cm²), and this was an improvement in comparison with 0.24% for BE–PPV and 1.32% for MEH–PPV under the same experimental conditions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Efficient white polymer-light-emitting-diodes based on polyfluorene end-capped with yellowish-green fluorescent dye and blended with a red phosphorescent iridium complex

A novel series of blue and yellowish-green light-emitting single polymers were prepared by end-capping of low contents of 4-bromo-7H-benzo [de]naphtha[2′,3′:4,5]imidazo[2,1-a]isoquinolin-7-one (M1) into polyfluorene. Electroluminescence (EL) spectra of these polymers exhibit blue emission (λ_max = 430/460 nm) from the fluorene segments and yellowish-green emission (λ_max = 510/530 nm) from the M1 units. For the polymer (PFNAP-0.06) with the M1 unit content of 0.06 mol-%, its EL spectrum shows balanced intensities of blue emission and yellowish-green emission with Commission Internationale de l'Eclairage (CIE) coordinates of (0.25, 0.34). The maximum brightness of the device prepared from the polymer (PFNAP-0.06) is 6704 cd/m² at 10 V with a structure of indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid) [PEDOT:PSS]/PVK/emission layer/Ca/Ag. A new white polymer-light-emitting-diode (WPLED) can be developed from the single polymer (PFNAP-0.06) system blended with a red phosphorescent iridium complex [Bis(2-[2′-benzothienyl)-pyridinato-N,C^3′] iridium (acetylacetonate) (BtpIr)]. We were able to obtain a white-light-emission device by adjusting the molar ratio of BtpIr to PFNAP-0.06 with a structure of indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid) [PEDOT:PSS]/PVK/emission layer/Ca/Ag. The brightness in such a device configuration is 4030 cd/m² at 9 V with CIE coordinates of (0.32, 0.34).     

Synthesis and characterization of novel polyphenol species derived from bis(4‐aminophenyl)ether: Substituent effects on thermal behavior,electrical conductivity,solubility, and optical band gap

In this study, four different Schiff bases namely 4,4′‐oxybis[N‐(2‐hydroxybenzilidene)aniline] (2‐HBA), 4,4′‐oxybis[N‐(4‐hydroxybenzilidene)aniline] (4‐HBA), 4,4′‐oxybis[N‐(3,4‐dihydroxybenzilidene)aniline] (3,4‐HBA), and 4,4′‐oxybis[N‐(4‐hydroxy‐3‐methoxybenzilidene)aniline] (HMBA) were synthesized. These Schiff bases were converted to their polymers that have generate names of poly‐4,4′‐oxybis[N‐(2‐hydroxybenzilidene)aniline] (P‐2‐HBA), poly‐4,4′‐oxybis[N‐(4‐hydroxybenzilidene)aniline] (P‐4‐HBA), poly‐4,4′‐oxybis[N‐(3,4‐dihydroxybenzilidene)aniline] (P‐3,4‐HBA), and poly‐4,4′‐oxybis[N‐(4‐hydroxy‐3‐methoxybenzilidene)aniline] (PHMBA) via oxidative polycondensation reaction by using NaOCl as the oxidant. Four different metal complexes were also synthesized from 2‐HBA and P‐2‐HBA. The structures of the compounds were confirmed by FTIR, UV‐vis, ¹H and ¹³C NMR analyses. According to ¹H NMR spectra, the polymerization of the 2‐HBA and 4‐HBA largely maintained with C? O? C coupling, whereas the polymerization of the 3,4‐HBA and HMBA largely maintained with C? C coupling. The characterization was made by TG‐DTA, size exclusion chromatography and solubility tests. Also, electrical conductivity of the polymers and the metal complex compounds were measured, showing that the synthesized polymers are semiconductors and their conductivities can be increased highly via doping with iodine ions (except PHMBA). According to UV–vis measurements, the optical band gaps (E_g) were found to be 3.15, 2.06, 3.23, 3.02, 2.61, 2.47, 2.64, 2.42, 2.83, 2.77, 2.78, and 2.78 for 2‐HBA, P‐2‐HBA, 4‐HBA, P‐4‐HBA, 3,4‐HBA, P‐3,4‐HBA, HMBA, PHMBA, 2‐HBA‐Cu, 2‐HBA‐Co, P‐2‐HBA‐Cu, and P‐2‐HBA‐Co, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Electropolymerization kinetic study of 3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine and its optical optimization for electrochromic window applications

Poly (3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine), PProDOT-Me₂, is one of the most promising conducting polymers in the alkylenedioxythiophene based family for electrochromic window applications. In the electropolymerization kinetic study of 3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine (ProDOT-Me₂), microgravimetry and chronoamperometry were used to determine the reaction orders with respect to the electrolyte and monomer, and the corresponding general kinetic equation of electropolymerization. This study presents that monomer concentration has a strong impact on electropolymerization mechanism. The relationship between film thickness and polymerization time was analyzed indicating that saturation of polymerization reduced the increase rate of film thickness with polymerization time. Also, the electropolymerization conditions were optimized to reach high contrast (Δ%T > 70%) with the minimum of transmittance (%T_min < 1) for electrochromic window applications.     

Electrochemical and optical properties of dicyclohexylmethyl substituted poly(3,4‐propylenedioxythiophene) analogue

An analogue of disubstituted 3,4‐propylenedioxythiophenes, namely 3,3‐bis(cyclohexylmethyl)‐3,4‐dihydro‐2H‐thieno[3,4‐b][1,4]dioxepin (ProDOT‐CycHex₂), was synthesized and its electrochemical polymerization was carried out successfully in an electrolyte solution of 0.1 M tetrabutylammonium hexafluorophosphate dissolved in a mixture of acetonitrile and dichloromethane (3/1: v/v). The corresponding polymer called PProDOT‐CycHex₂ has a reduced band gap of 1.85 eV and an electrochromic property: blue/violet when neutralized and highly transparent when oxidized. Also, PProDOT‐CycHex₂ film exhibited faster response time (0.7 s) and higher coloration efficiency (769 cm²/C) during oxidation when compared to its benzyl substituted analogue. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46214.     

Faradaic charge corrected colouration efficiency measurements for electrochromic devices

We report a new technique for measuring colouration efficiency (CE) for electrochromic polymers and devices. Faradaic charge associated with redox activity leading to chromic change was extracted from the total charge flow during a device switch. Typically, Faradaic charge is extracted from the total charge by first measuring a blank device (i.e. no polymer deposited). This is used as the baseline and subtracted from subsequent measurements with the polymer deposited into the device. The method is open to inaccuracies if the surface area before and after polymer deposition is different or if the inherent capacitance of the device is altered by the addition of the polymer(s). The new technique does not suffer from this drawback as it dispenses with the need to measure blank devices. To investigate the utility of this method a poly(3,4-ethylenedioxthiophene) (PEDOT) and polyaniline (PANI) electrochromic cell was tested. CE measurements at an optical density change of 95% (λ = 555 nm) were recorded for the following three conditions: uncorrected, CE_UC = 388 cm²/C; background corrected, CE_BC = 391 cm²/C and; Faradaic corrected, CE_FC = 2173 cm²/C. The result highlights the fact that the CE value of chromic polymers or devices may be higher than what is currently being reported.     

Influence of side chains on electrochromic properties of green donor–acceptor–donor polymers

Three solution processable cathodically coloring green electrochromic polymers, based on 2,3-diphenyl-5,7-di(thiophen-2-yl)thieno[3,4-b]pyrazine, have been synthesized by oxidative FeCl₃ polymerization. The polymers were designed with solubilizing alkyl and oligoethylene oxide side chains to achieve solubility and processability. All three polymers have a small electrochemical bandgap (1.8–1.9 eV) and low oxidation potentials. Spectroelectrochemical studies of polymer films on ITO reveal that the alkyl side chains in head-to-head position on the polymer backbone promote a defined high-energy absorption peak and suppress tailing of charge-carrier absorption into the visible region. Kinetic studies, based on transmission measurements applying a square-wave potential between reduced and oxidized states, show that the polymer with exclusively oligoethylene oxide side chains (P3) had the fastest response times, monitored at the low-energy absorption maxima. The best performing polymer (P1) showed a good optical contrast in the visible region with a ΔT of 26% at 700 nm. An initial test of the electrochemical stability showed that the oligoethylene oxide containing polymers had superior stability over 500 full switches.     

Preparation and electro‐optic properties of novel Y‐type polyimides with highly enhanced thermal stability of second harmonic generation

BACKGROUND: In the development of nonlinear optical (NLO) polymers for electro‐optic device applications, stabilization of electrically induced dipole alignment is one of the important criteria. Polyimides for NLO applications have attracted attention because of their high T_g values and high thermal stability. In this work we designed and synthesized a new type of NLO polyimide, in which the pendant NLO chromophores are parts of the polymer backbone. These mid‐type NLO polymers are expected to have the merits of both main‐chain and side‐chain NLO polymers: stabilization of dipole alignment and good solubility. RESULTS: 3,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐4′‐nitrostilbene dianhydride was prepared and reacted with the corresponding aromatic diamine to yield unprecedented Y‐type polyimides containing 3,4‐dioxynitrostilbenyl groups as NLO chromophores, which constituted parts of the polymer backbones. The resulting polyimides are soluble in polar solvents such as dimethylformamide and dimethylsulfoxide. These polymers showed a thermal stability up to 320 °C in thermogravimetric thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 143–164 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm^?1 fundamental wavelength were around 9.45 × 10^?18 C. CONCLUSION: The dipole alignment exhibited exceptionally high thermal stability even at 30 °C higher than T_g. There was no SHG decay below 180–190 °C because of the partial main‐chain character of the polymer structure, which is acceptable for NLO device applications. Copyright © 2007 Society of Chemical Industry     

Specroelectrochemical,switching kinetics,and chronoamperometric studies of dibenzyl derivative of poly(3,4‐propylenedioxythiophene) thin‐film‐based electrochromic device

The dibenzyl derivative of poly(3,4‐propylenedioxythiophene) (PProDOT‐Bz₂) thin film is deposited onto ITO‐coated glass substrate by electropolymerization technique. The electropolymerization of ProDOT‐Bz₂ is carried out by a three‐electrode electrochemical cell. The cyclic voltammogram shows the redox properties of electrochemically prepared films deposited at different scan rates. The thin films prepared were characterized for its morphological properties to study the homogeniety. Classic six‐layer structure of PProDOT‐Bz₂ electrochromic device using this material was fabricated and reported for the first and its characterizations such as spectroelectrochemical, switching kinetics, and chronoamperometric studies are performed. The color contrast of the thin film and the device achieved are 64 and 40%, respectively, at λ_max (628 nm). The switching time is recorded and the observed values are 5 s from the coloring state to the bleaching state and vice versa. The chronoamperometry shows that the device performed up to 400 cycles, and it is capable of working up to 35 cycles without any degradation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40717.     

Donor copolymer with benzo[1,2‐b:4,5‐b′]dithiophene and quinoxaline derivative segments for photovoltaic applications

A donor copolymer Poly{2,6‐4,8‐bis(2‐ethylhexyl)benzo[1,2‐b:3,4‐b′]dithiophene‐5,8‐2,3‐bis(5‐octylthiophen‐2‐yl)quinoxaline} (PBDTThQx) with benzo[1,2‐b:4,5‐b′]dithiophene and quinoxaline derivatives was synthesized and characterized with NMR, ultraviolet–visible spectroscopy, thermogravimetric analyses, and cyclic voltammetry. Photovoltaic devices with the configuration indium tin oxide–poly(3,4‐ethylenedioxythiophene)–poly(styrene sulfonate)–PBDTThQx–[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM)–LiF–Al were fabricated, in which PBDTThQx performed as the electron donor and PC₆₁BM was the electron acceptor in the active layer. The device presented reasonable photovoltaic properties when the weight ratio of PBDTThQx:PC₆₁BM reached 1:3. The open‐circuit voltage, fill factor, and power conversion efficiency were gauged to be 0.75 V, 0.59, and 0.74%, respectively. The experimental data implied that PBDTThQx would be a promising donor candidate in the application of polymer solar cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40279.     

D-A type hybrid polymers based on EDOT and various benzodiazoles for electrochromic materials

Two donor units (D)-acceptor units (A) type monomers were synthesized by Stille coupling reaction, and then three D-A type hybrid polymers based on 3,4-ethylenedioxythiophene and various benzodiazoles were synthesized by electrochemical polymerization. Spectroelectrochemical and kinetic studies of these polymers showed that all polymer films exhibited excellent electrochromic behavior, obvious optical contrast, and excellent stability. Among them, the response time of P3 film was the shortest (t_c = 1.6 s, t_b = 2.2 s), the coloring efficiency of P2 film was the highest (CE = 333 cm²·C⁻¹), and the stability of P1 was the best (the ΔT loss of P1 after 1000 s cycles is only 2.3%). Therefore, these data prove that these new polymers have great potential in applications as electrochromic materials.     

A tungsten-trioxide/prussian blue complementary electrochromic cell with a polymer electrolyte

Optically variable windows (smart windows), which control the transmission of light into buildings and vehicles, are of interest both for the control of solar heat load and for privacy applications. Such windows are likely to utilize electrochromic technology to achieve optical control. An electrochromic device consisting of a cathodically colouring tungsten trioxide (WO₃) film, an anodically colouring Prussian blue (PB) film, and a polymer electrolyte was made. The polymer electrolyte was prepared from polyvinyl alcohol doped with H₃PO₄ and KH₂PO₄ to accommodate the conduction of both H⁺ and K⁺ ions. The electrochromic WO₃ and PB films functioned in a complementary way such that the device was coloured or bleached by the application of –0.5 V or +0.5 V (WO₃ films vs PB film), respectively. The spectral characteristics of the coloured device confirmed the complementary colouration of WO₃ and PB in the device.     

Light‐emitting polymers containing 2,3,4,5‐tetraphenylthiophenyl moiety and different pendent groups

By appropriate chemical reaction, different substituents can be selectively attached to the four phenyl rings present in 2,3,4,5‐tetraphenylthiophene (TP) to prepare monomers, namely 2,5‐bis(4‐bromophenyl)‐3,4‐diphenylthiophene (BTP), 2,5‐bis(4‐bromophenyl)‐3,4‐bis[4‐(nonan‐1‐one)phenyl] thiophene (BTP‐N2) and 2,5‐bis(4‐bromophenyl)‐3,4‐bis[4‐(2‐heptyl‐4‐phenylquinoline)phenyl]thiophene (BTP‐Qu2). Three light‐emitting polymers, PTP, PTP‐N2 and PTP‐Qu2, with the common TP backbone were prepared by zero‐valent nickel‐catalyzed polymerization of BTP, BTP‐N2 and BTP‐Qu2 monomers, respectively. The substituent on the 3,4‐phenyl rings of the TP framework has a profound effect on the polymer properties. Without any 3,4‐substituent, the rigid PTP polymer has low solubility in organic solvents. With the flexible nonanoyl substituent, the corresponding polymer, PTP‐N2, has improved solubility but low quantum efficiency (Φ_F) due to the carbonyl group which enhances intersystem crossing. With both flexible chain and bulky 4‐phenylquinoline (PQ) ring substituents, PTP‐Qu2 has good solubility and an enhanced Φ_F since the introduction of both flexible chain and bulky PQ ring substituents prevents close chain packing. All three polymers exhibit similar emission spectra despite the distinct difference in the absorption pattern of PTP‐Qu2 compared with those of PTP and PTP‐N2. In the case of PTP‐Qu2, there is energy transfer from the PQ pendent ring to the TP backbone and results in emission similar to PTP and PTP‐N2. The TP backbone common in all the three polymers is responsible for the emission from the corresponding excited states. The electrochemical properties of PTP‐Qu2 were also investigated. Copyright © 2005 Society of Chemical Industry     

Nanocomposite polymer electrolytes by in situ polymerization of methyl methacrylate: For electrochemical applications

Hybrid materials, which combine properties of organic–inorganic materials, are of profound interest owing to their unexpected synergistically derived properties and are considered as innovative advanced materials promising new applications in many fields such as optics, electronics, ionics and mechanics. Inorganic fillers are added to polymers in order to increase some of the properties of the compounds. These hybrid polymeric materials are replacing the pristine polymers due to their higher strength and stiffness. In the present work, studies concerning the preparation of poly (methylmethacrylate) [PMMA] and the nanocomposites PMMA/SiO₂, PMMA/TiO₂ are reported. These nanocomposite polymers were synthesized by means of free radical polymerization of methylmethacrylate, further “sol–gel” transformation‐based hydrolysis and condensation of corresponding alkoxide was used to prepare the inorganic phase during the polymerization process of MMA. Electrolytes were synthesized based on these nanocomposite polymers and have shown superior properties as compared to conventional polymer electrolytes. The nanocomposites and the nanocomposite polymer electrolytes (NPEs) with different lithium salts were investigated through an array of techniques including FTIR and calorimetry along with the electrochemical and rheological techniques. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and electro‐optical properties of novel Y‐type polyurethanes containing dioxynitrostilbene

3,4‐Di‐(2′‐hydroxyethoxy)‐4′‐nitrostilbene (2) was prepared by the reaction of 2‐iodoethanol with 3,4‐dihydroxy‐4′‐nitrostilbene. Diol 2 was condensed with 2,4‐toluenediisocyanate, 3,3′‐dimethoxy‐4,4′‐biphenylenediisocyanate and 1,6‐hexamethylenediisocyanate to yield novel Y‐type polyurethanes 3–5 containing dioxynitrostilbene as a non‐linear optical (NLO)‐chromophore. Polymers 3–5 were soluble in common organic solvents, such as acetone and DMF. These polymers showed thermal stability up to 280 °C in TGA thermograms with T_g values in the range of 100–143 °C in DSC thermograms. The approximate lengths of aligned NLO‐chromophores of the polymers estimated from AFM images were around 2 nm. The SHG coefficients (d₃₃) of poled polymer films were around 4.5 × 10^?8 esu. Poled polymer films had improved temporal and long‐term thermal stability owing to the hydrogen bonding of urethane linkage and the main‐chain character of the polymer structure, which are acceptable for NLO device applications. Copyright © 2004 Society of Chemical Industry     

Organic multiviologen electrochromic cells for a color electronic display application

The electrochromic (EC) and optical properties of three new viologen compounds containing 1,1′‐di‐n‐heptyl‐4,4′‐bipyridinum dibromide (DHBPDB; C₂₄H₃₈Br₂N₂), 1‐heptyl‐4‐(4‐pyridyl)pyridinium bromide (HPPB; C₁₇H₂₃BrN₂), and 1,1′‐dis(p‐cyanophenyl)‐4,4′‐bipyridinium chloride (DCBPC; C₁₂H₈N₂OBr₂) for potential use in electrochromism applications were investigated. The repetitive stability of all of the EC cells could be improved through the addition of ferrocene as an electron donor (a counter redox material) to the electrolyte solution under several redox cycles. The experimental results demonstrate that the EC cell showed a reversible color change from clear (tintless) to three different colors with the application of electrochemical stimuli at specific potentials. The color of the EC cells turned red, green, or blue upon electrochemical reduction for DHBPDB, HPPB, and DCBPC in indium tin oxide sandwich‐type cells. Because of the different viologen molecules competing to capture electrons and affecting the EC efficiency and life of the multiviologen cells, they could be improved by the optimization of the working voltage in the multiviologen cells from the modification of an operative potential based on the cyclic voltammetry measurements. In this article, we propose a prototype device of multicolor electrochromic display, which provides potential application for multicolor electronic displays or EC paper. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40485.