Isothermal kinetics of (E)‐4‐(4‐metoxyphenyl)‐4‐oxo‐2‐butenoic acid release from a poly(acrylic acid‐co‐methacrylic acid) hydrogel

A kinetic study of the release of the drug (E)‐4‐(4‐metoxyphenyl)‐4‐oxo‐2‐butenoic acid (MEPBA) from a poly(acrylic acid‐co‐methacrylic acid) (PAA‐co‐MA) hydrogel was performed. The isothermal kinetic curves of MEPBA release from the PAA‐co‐MA hydrogel in bidistilled water at different temperatures ranging from 20 to 40°C were determined. The reaction rate constants of the investigated process were determined with the initial rate, the saturation rate, and Peppas's semiempirical equation. Also, a model‐fitting method for the determination of the kinetics model of drug release was applied. The influence of α at the values of the kinetic parameters and the presence of a compensation effect was established. A procedure for the determination of the distribution function of the activation energies was developed. This procedure was based on the experimentally determined relationship between the activation energy and α. The mechanism of active compound release is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The Alkylquinolone Repertoire of Pseudomonas aeruginosa is Linked to Structural Flexibility of the FabH‐like 2‐Heptyl‐3‐hydroxy‐4(1H)‐quinolone (PQS) Biosynthesis Enzyme PqsBC

Pseudomonas aeruginosa is a bacterial pathogen that causes life‐threatening infections in immunocompromised patients. It produces a large armory of saturated and mono‐unsaturated 2‐alkyl‐4(1H)‐quinolones (AQs) and AQ N‐oxides (AQNOs) that serve as signaling molecules to control the production of virulence factors and that are involved in membrane vesicle formation and iron chelation; furthermore, they also have, for example, antibiotic properties. It has been shown that the β‐ketoacyl‐acyl‐carrier protein synthase III (FabH)‐like heterodimeric enzyme PqsBC catalyzes the last step in the biosynthesis of the most abundant AQ congener, 2‐heptyl‐4(1H)‐quinolone (HHQ), by condensing octanoyl‐coenzyme A (CoA) with 2‐aminobenzoylacetate (2‐ABA), but the basis for the large number of other AQs/AQNOs produced by P. aeruginosa is not known. Here, we demonstrate that PqsBC uses different medium‐chain acyl‐CoAs to produce various saturated AQs/AQNOs and that it also biosynthesizes mono‐unsaturated congeners. Further, we determined the structures of PqsBC in four different crystal forms at 1.5 to 2.7 Å resolution. Together with a previous report, the data reveal that PqsBC adopts open, intermediate, and closed conformations that alter the shape of the acyl‐binding cavity and explain the promiscuity of PqsBC. The different conformations also allow us to propose a model for structural transitions that accompany the catalytic cycle of PqsBC that might have broader implications for other FabH‐enzymes, for which such structural transitions have been postulated but have never been observed.     

Direct synthesis of poly(4′‐oxy‐4‐biphenylcarbonyl) and poly(2‐oxy‐6‐naphthoyl) under nonstoichiometric conditions

Direct synthesis of poly(4′‐oxy‐4‐biphenylcarbonyl) (POBP) and poly(2‐oxy‐6‐naphthoyl) (PON) was examined by polycondensation of 4′‐hydroxy‐4‐biphenylcarboxylic acid (HBPA) and 2‐hydroxy‐6‐naphthoic acid (HNA) in the presence of 4‐ethoxybenzoic anhydride or 2‐naphthoic anhydride as condensation reagents. Polymerizations were carried out at 320 °C in aromatic solvents and liquid paraffin. POBP, having a number‐average degree of polymerization (DPn) of 38, was obtained as plate‐like crystals at the molar ratio of HBPA and anhydride of 50 mol%. PON was also obtained as plate‐like crystals but the DPn was only 13. HBPA and HNA were first converted to reactive acyloxyaromatic acid intermediates. Then the DPn was increased by means of reaction‐induced crystallization of oligomers and subsequent solid‐state polymerization via an acid–ester exchange under nonstoichiometric conditions caused by the monocarboxylic acid by‐product. Even though the DPn of PON was not as high, direct polycondensation of HBPA and HNA proceeded successfully with aromatic anhydrides. Copyright © 2004 Society of Chemical Industry     

Synthesis,Crystal Structure,and Thermal Behavior of 3‐(4‐Aminofurazan‐3‐yl)‐4‐(4‐nitrofurazan‐3‐yl)furazan (ANTF)

The energetic material 3‐(4‐aminofurazan‐3‐yl)‐4‐(4‐nitrofurazan‐3‐yl)furazan (ANTF) with low melting‐point was synthesized by means of an improved oxidation reaction from 3,4‐bis(4′‐aminofurazano‐3′‐yl)furazan. The structure of ANTF was confirmed by ¹³C NMR spectroscopy, mass spectrometry, and the crystal structure was determined by X‐ray diffraction. ANTF crystallized in monoclinic system P2₁/c, with a crystal density of 1.785 g cm⁻³ and crystal parameters a=6.6226(9) Å, b=26.294(2) Å, c=6.5394(8) Å, β=119.545(17)°, V=0.9907(2) nm³, Z=4, μ=0.157 mm⁻¹, F(000)=536. The thermal stability and non‐isothermal kinetics of ANTF were studied by differential scanning calorimetry (DSC) with heating rates of 2.5, 5, 10, and 20 K min⁻¹. The apparent activation energy (E_a) of ANTF calculated by Kissinger's equation and Ozawa's equation were 115.9 kJ mol⁻¹ and 112.6 kJ mol⁻¹, respectively, with the pre‐exponential factor lnA=21.7 s⁻¹. ANTF is a potential candidate for the melt‐cast explosive with good thermal stability and detonation performance.     

Synthesis and characterization of new cardo poly(bisbenzothiazole)s from 1,1‐bis(4‐amino‐3‐mercaptophenyl)‐4‐tert‐butylcyclohexane dihydrochloride

A new monomer 1,1‐bis(4‐amino‐3‐mercaptophenyl)‐4‐tert‐butylcyclohexane dihydrochloride, bearing the bulky pendant 4‐tert‐butylcyclohexylidene group, was synthesized from 4‐tert‐butylcyclohexanone in three steps. Its chemical structure was characterized by ¹H NMR, ¹³C NMR, MS, FTIR, and EA. Aromatic poly(bisbenzothiazole)s (PBTs V) were prepared from the new monomer and five aromatic dicarboxylic acids by direct polycondensation. The inherent viscosities were in the range of 0.63–2.17 dL/g. These polymers exhibited good solubility and thermal stability. Most of the prepared PBTs V were soluble in various polar solvents. Thermogravimetric analysis showed the decomposition temperatures at 10% weight loss that were in the range of 495–534°C in nitrogen. All the PBTs V, characterized by X‐ray diffraction, were amorphous. The UV absorption spectra of PBTs V showed a range of λ_max from 334 to 394 nm. All the PBTs V prepared had evident fluorescence emission peaks, ranging from 423 to 475 nm with different intensity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2000–2008, 2006     

Optically Active 4‐Substituted (S)‐2‐Phenyl‐2‐oxazolines

(R)‐4‐Hydroxymethyl‐2‐phenyl‐2‐oxazoline (R)‐ 1 ) was prepared from (L)‐serine. The respective tosylate ((S)‐ 2 ) was converted into sulfides (S)‐ 4 and (S)‐ 5 , and sulfone (S)‐ 6 , useful starting materials for the elaboration of additional chiral centers. A previously reported [ α]_D ²⁵ value for (R)‐ 4 is corrected.     

Synthesis and characterization of novel aromatic poly(amide‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl or 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic diamines

New aromatic diimide‐dicarboxylic acids having kinked and cranked structures, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b), were synthesized by the reaction of trimellitic anhydride with 2,2′‐bis(4‐aminophenoxy)biphenyl (1a) and 2,2′‐bis(4‐aminophenoxy)‐1,1′‐binaphthyl (1b), respectively. Compounds 2a and 2b were characterized by FT‐IR and NMR spectroscopy and elemental analyses. Then, a series of novel aromatic poly(amide‐imide)s were prepared by the phosphorylation polycondensation of the synthesized monomers with various aromatic diamines. Owing to structural similarity, and a comparison of the characterization data, a model compound was synthesized by the reaction of 2b with aniline. The resulting polymers with inherent viscosities of 0.58–0.97 dl g^?1 were obtained in high yield. The polymers were fully characterized by FT‐IR and NMR spectroscopy. The ultraviolet λ_max values of the poly(amide‐imide)s were also determined. The polymers were readily soluble in polar aprotic solvents. They exhibited excellent thermal stabilities and had 10% weight loss at temperatures above 500 °C under a nitrogen atmosphere. Copyright © 2003 Society of Chemical Industry     

Synthesis and properties of polyamides derived from 4,6‐bis(4‐chloroformylphenylthio)pyrimidine and 3,6‐bis(4‐chloroformylphenylthio)pyridazine

Two kinds of monomers containing thioether units 4,6‐bis(4‐chloroformylphenylthio)pyrimidine (BPPM‐DC) and 3,6‐bis(4‐chloroformylphenylthio)pyridazine (BPPD‐DC) were synthesized by two steps and were reacted with diamine‐containing thioether (?S–) and sulfone units to prepare a kind of polyamide containing heterocycles and high contents of thioether groups. These polyamides had good optical properties, including an optical transmittance of the aromatic polyamide film at 450 nm that was higher than 87%. Additionally, the pyridazine, pyrimidine and the large quantity of thioether units provided the polymers with high refractive indices of 1.722–1.732 and low birefringences of 0.004–0.006. These polyamides were also found to have good thermal properties. They showed improved solubility in polar aprotic solvents and could form tough films with a tensile strength of 79.2–112.3 MPa and a storage modulus of 1.4–2.4 GPa (at 200 °C).© 2013 Society of Chemical Industry     

Thermal and Combustion Properties of 3,4‐Bis(3‐nitrofurazan‐4‐yl)furoxan (DNTF)

Thermal decomposition of melted 3,4‐bis(3‐nitrofurazan‐4‐yl)furoxan (DNTF) in isothermal conditions was studied. The burning rates of DNTF were measured in the pressure interval of 0.1–15 MPa. The thermal stability of DNTF was found to be close to the stability of HMX, while the burning rate of DNTF was close to the burning rate of CL‐20. The thermocouple measurements in the combustion wave of DNTF showed that combustion of DNTF was controlled by the gas‐phase mechanism. The DNTF vapor pressure was determined from thermocouple measurements and agreed well with data obtained at low temperatures under isothermal conditions.     

Kinetic analysis of the swelling behavior of poly(n‐butylacrylate‐1,6‐hexanedioldiacrylate) networks in 4‐cyano‐4′‐n‐pentyl‐biphenyl (5CB)

The dynamic swelling behavior of chemically crosslinked poly(n‐butylacrylate/1,6‐hexanedioldiacrylate) [poly(Abu‐HDDA)] networks, immersed in an nematogenic and two isotropic solvents, was experimentally analyzed. These networks were elaborated by ultraviolet (UV)–visible light‐induced radical polymerization/crosslinking reactions of Abu/HDDA mixtures, to yield poly(Abu/0.5 wt % HDDA) and poly(Abu/5 wt % HDDA) networks corresponding to weakly and strongly crosslinked systems, respectively. The swelling behavior of these poly(Abu‐HDDA) networks was investigated by immersion in excess solvent, followed by subsequent measurements of the variation of the sample size by means of optical microscopy, depending on temperature and immersion time. Methanol and toluene were employed as isotropic solvents and the nematic liquid crystal molecule 4‐cyano‐4 ′ ‐n‐pentyl‐biphenyl, was considered as anisotropic medium. Swelling ratios were calculated by taking into account diameter sizes as function of immersion time compared to the dry state. Experimental data were analyzed using the Komori–Sakamoto approach and the results of this model were found to be in good agreement with the obtained data. The plateau values of the swelling curves at equilibrium were used to establish phase diagrams as function of temperature and solvent concentration. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45452.     

Photopolymer: synthesis and characterization of poly(4‐methacryloyloxyphenyl‐4′‐chlorostyryl ketone)

Methacrylate monomer containing a photodimerizable α,β‐unsaturated ketone moiety was prepared and polymerized in ethyl methyl ketone at 70 °C using benzoyl peroxide as an initiator. The polymer was characterized by UV, IR, ¹H NMR and ¹³C NMR spectra. The molecular weights (M _w and M _n) of the polymer were determined by gel permeation chromotography. The thermal stability of the polymer was measured by thermogravimetric analysis in air and nitrogen. The glass transition temperature of the polymer was determined by differential scanning calorimetry. The photo reactivity of the polymer was investigated as thin film and in solution. © 2000 Society of Chemical Industry     

Platinum(II) as Bifunctional Linker in Antibody–Drug Conjugate Formation: Coupling of a 4‐Nitrobenzo‐2‐oxa‐1,3‐diazole Fluorophore to Trastuzumab as a Model

The potential of platinum(II) as a bifunctional linker in the coordination of small molecules, such as imaging agents or (cytotoxic) drugs, to monoclonal antibodies (mAbs) was investigated with a 4‐nitrobenzo‐2‐oxa‐1,3‐diazole (NBD) fluorophore and trastuzumab (Herceptin?) as a model antibody. The effect of ligand and reaction conditions on conjugation efficiency was explored for [Pt(en)(L‐NBD)Cl](NO₃) (en=ethylenediamine), with L=N‐heteroaromatic, N‐alkyl amine, or thioether. Conjugation proceeded most efficiently at pH 8.0 in the presence of NaClO₄ or Na₂SO₄ in tricine or HEPES buffer. Reaction of N‐coordinated complexes (20 equiv) with trastuzumab at 37 °C for 2 h, followed by removal of weakly bound complexes with excess thiourea, afforded conjugates with an NBD/mAb ratio of 1.5–2.9 that were stable in phosphate‐buffered saline at room temperature for at least 48 h. In contrast, thioether‐coordinated complexes afforded unstable conjugates. Finally, surface plasmon resonance analysis showed no loss in binding affinity of trastuzumab after conjugation.     

Synthesis and characterization of poly(hydroxyether). I. Poly(hydroxyether) based on 2,2‐bis(4‐hydroxyphenyl)hexafluoropropane and 2,2‐bis(4‐hydroxyphenyl)propane

Linear poly(hydroxyethers) (PHEs) were prepared by the base‐induced condensation of bisphenols with epichlorohydrin in a polar mixed solvent. The bisphenols used were 2,2‐bis(4‐hydroxyphenyl)propane (bisphenol A) and 2,2‐bis(4‐hydroxyphenyl)‐hexafluoropropane (bisphenol AF). Bisphenol A–based homo‐PHE (HPHE‐A), bisphenol AF–based homo‐PHE (HPHE‐AF), and copoly(hydroxyethers) (CPHEs) based on both the bisphenols with various compositions were characterized in terms of chemical structure, thermal property, solubility, and contact angle. The incorporation of bisphenol AF unit into HPHE‐A brought about the increases in the glass‐transition temperature, the solubility in organic solvents, and the hydrophobicity. The sequence of the repeating unit in the copolymer was analyzed by ¹H–NMR and the result agreed well with the one calculated as a random copolymer. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1687–1696, 2001     

Synthesis and Biological Characterization of (3R,4R)‐4‐(2‐(Benzhydryloxy)ethyl)‐1‐((R)‐2‐hydroxy‐2‐phenylethyl)‐piperidin‐3‐ol and Its Stereoisomers for Activity toward Monoamine Transporters

A novel series of optically active molecules based on a 4‐(2‐(benzhydryloxy)ethyl)‐1‐((R)‐2‐hydroxy‐2‐phenylethyl)‐piperidin‐3‐ol template were developed. Depending on stereochemistry, the compounds exhibit various degrees of affinity for three dopamine, serotonin, and norepinephrine transporters. These molecules have the potential for treating several neurological disorders such as drug abuse, depression, and attention deficit hyperactivity disorder.

     

Influence of the comonomers (styrene and methyl acrylate) on the rate of photocrosslinking of 4‐{[‐3‐(4‐hydroxybenzylidene)‐2‐oxocyclohexylidene]methyl}‐ phenyl acrylate

[2,6‐Bis(4‐hydroxybenzylidene)cyclohexanone] (HBC) was prepared by reacting cyclohexanone and p‐hydroxybenzaldehyde in the presence of acid catalyst. Acrylated derivative of HBC, 4‐{[‐3‐(4‐hydroxybenzylidene)‐2‐oxocyclohexylidene]methyl}phenyl acrylate (HBA), was prepared by reacting HBC with acryloyl chloride in the presence of triethylamine. Copolymers of HBA with styrene (S) and methyl acrylate (MA) of different feed compositions were carried out by solution polymerization technique by using benzoyl peroxide (BPO) under nitrogen atmosphere. All monomers and polymers were characterized by using IR and NMR techniques. Reactivity ratios of the monomers present in the polymer chain were evolved by using Finnman–Ross (FR), Kelen–Tudos (KT), and extended Kelen–Tudos (ex‐KT) methods. Average values of reactivity were achieved by the following three methods: r₁ (S) = 2.36 ± 0.45 and r₂ (HBA) = 0.8 ± 0.31 for poly(S‐co‐HBA); r₁ = 1.62 ± 0.06 (MA); and r₂ = 0.12 ± 0.07 (HBA) for poly(MA‐co‐HBA). The photocrosslinking property of the polymers was done by using UV absorption spectroscopic technique. The rate of photocrosslinking was enhanced compared to that of the homopolymers, when the HBA was copolymerized with S and MA. Thermal stability and molecular weights (M_w and M_n) were determined for the polymer samples. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2494–2503, 2004     

Acceleration of the Rate‐Limiting Step of Thioredoxin Folding by Replacement of its Conserved cis‐Proline with (4 S)‐Fluoroproline

The incorporation of the non‐natural amino acids (4R)‐ and (4S)‐fluoroproline (Flp) has been successfully used to improve protein stability, but little is known about their effect on protein folding kinetics. Here we analyzed the influence of (4R)‐ and (4S)‐Flp on the rate‐limiting trans‐to‐cis isomerization of the Ile75–Pro76 peptide bond in the folding of Escherichia coli thioredoxin (Trx). While (4R)‐Flp at position 76 had essentially no effect on the isomerization rate in the context of the intact tertiary structure, (4S)‐Flp accelerated the folding reaction ninefold. Similarly, tenfold faster trans‐to‐cis isomerization of Ile75–(4S)‐Flp76 relative to Ile75–Pro76 was observed in the unfolded state of Trx. Our results show that the replacement of cis prolines by non‐natural proline analogues can be used for modulating the folding rates of proteins with cis prolyl‐peptide bonds in the native state.     

High‐resolution thermogravimetry of poly(4‐methyl‐1‐pentene)

Thermal degradation and kinetics of poly(4‐methyl‐1‐pentene) were investigated by nonisothermal high‐resolution thermogravimetry at a variable heating rate. Thermal degradation temperatures are higher, but the maximum degradation rates are lower in nitrogen than in air. The degradation process in nitrogen is quite different from that in air. The average activation energy and frequency factor of the first stage of thermal degradation for the poly(4‐methyl‐1‐pentene) are 2.4 and 2.8 times greater in air than those in nitrogen, respectively. Poly(4‐methyl‐1‐pentene) exhibits almost the same decomposition order of 2.0 and char yield of 14.3–14.5 wt % above 500°C in nitrogen and air. The isothermal lifetime was estimated based on the kinetic parameters of nonisothermal degradation and compared with the isothermal lifetime observed experimentally. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2201–2207, 1999