Thermal efficiency of solid electrolyte fuel cells with mixed conduction

The effect of mixed anionic and n-type electronic conduction in solid electrolytes on the thermal efficiency of a fuel cell system was analyzed quantitatively. The mixed conduction observed when electrolytes based on ceria are used in H₂/air fuel cell applications lowers the maximum attainable cell thermal efficiency to below 40%. Neither the zirconia nor the ceria based solid oxide electrolytes studied to date can be used in a low temperature (700 °C) system that meets simultaneously the requirements of power density and thermal efficiency for electric utility power plants. The material properties required for an advanced fuel cell power plant solid electrolyte were derived in terms of the ionic conductivity and the Schmalzried parameters P⊕ and P? : σ_ion > 0.033 (ω-cm)^?1, P⊕ > 10³ atm., P? < 10^?23 atm. at 700 °C.     

Enhanced performance of solid oxide fuel cells with Ni/CeO2 modified La0.75Sr0.25Cr0.5Mn0.5O3−δ anodes

The optimization of electrodes for solid oxide fuel cells (SOFCs) has been achieved via a wet impregnation method. Pure La_0.75Sr_0.25Cr_0.5Mn_0.5O_3−δ (LSCrM) anodes are modified using Ni(NO₃)₂ and/or Ce(NO₃)₃/(Sm,Ce)(NO₃)_x solution. Several yttria-stabilized zirconia (YSZ) electrolyte-supported fuel cells are tested to clarify the contribution of Ni and/or CeO₂ to the cell performance. For the cell using pure-LSCrM anodes, the maximum power density (P_max) at 850 °C is 198 mW cm⁻² when dry H₂ and air are used as the fuel and oxidant, respectively. When H₂ is changed to CH₄, the value of P_max is 32 mW cm⁻². After 8.9 wt.% Ni and 5.8 wt.% CeO₂ are introduced into the LSCrM anode, the cell exhibits increased values of P_max 432, 681, 948 and 1135 mW cm⁻² at 700, 750, 800 and 850 °C, respectively, with dry H₂ as fuel and air as oxidant. When O₂ at 50 mL min⁻¹ is used as the oxidant, the value of P_max increases to 1450 mW cm⁻² at 850 °C. When dry CH₄ is used as fuel and air as oxidant, the values of P_max reach 95, 197, 421 and 645 mW cm⁻² at 750, 800, 850 and 900 °C, respectively. The introduction of Ni greatly improves the performance of the LSCrM anode but does not cause any carbon deposit.     

Characterization of the 75% Gd0.8Sr0.2CoO3−δ/25% Ce0.9Gd0.1O2−δ composite cathode system for use in intermediate temperature solid oxide fuel cells

The composite cathode system is examined for suitability on a Ce_0.9Gd_0.1O_2−δ electrolyte based solid oxide fuel cell at intermediate temperatures (500–700 °C). The cathode is characterized for electronic conductivity and area specific charge transfer resistance. This cathode system is chosen for its excellent thermal expansion match to the electrolyte, its relatively high conductivity (115 S cm⁻¹ at 700 °C), and its low activation energy for oxygen reduction (99 kJ mol⁻¹). It is found that the decrease of sintering temperature of the composite cathode system produces a significant decrease in charge transfer resistances to as low as 0.25 Ω cm². The conductivity of the cathode systems is between 40 and 88 S cm⁻¹ for open porosities of 30–40%.     

ZnO-doped BaZr0.85Y0.15O3−δ proton-conducting electrolytes: Characterization and fabrication of thin films

ZnO-doped BaZr_0.85Y_0.15O_3−δ perovskite oxide sintered at 1500 °C has bulk conductivity of the order of 10⁻² S cm⁻¹ above 650 °C, which makes it an attractive proton-conducting electrolyte for intermediate-temperature solid oxide fuel cells. The structure, morphology and electrical conductivity of the electrolyte vary with sintering temperature. Optimal electrochemical performance is achieved when the sintering temperature is about 1500 °C. Cathode-supported electrolyte assemblies were prepared using spin coating technique. Thin film electrolytes were shown to be dense using SEM and EDX analyses.     

La0.84Sr0.16MnO3−δ cathodes impregnated with Bi1.4Er0.6O3 for intermediate-temperature solid oxide fuel cells

La_0.84Sr_0.16MnO_3−δ–Bi_1.4Er_0.6O₃ (LSM–ESB) composite cathodes are fabricated by impregnating LSM electronic conducting matrix with the ion-conducting ESB for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The performance of LSM–ESB cathodes is investigated at temperatures below 750 °C by AC impedance spectroscopy. The ion-impregnation of ESB significantly enhances the electrocatalytic activity of the LSM electrodes for the oxygen reduction reactions, and the ion-impregnated LSM–ESB composite cathodes show excellent performance. At 750 °C, the value of the cathode polarization resistance (R_p) is only 0.11 Ω cm² for an ion-impregnated LSM–ESB cathode, which also shows high stability during a period of 200 h. For the performance testing of single cells, the maximum power density is 0.74 W cm⁻² at 700 °C for a cell with the LSM–ESB cathode. The results demonstrate the ion-impregnated LSM–ESB is one of the promising cathode materials for intermediate-temperature solid oxide fuel cells.     

Structural, thermal and electrochemical properties of layered perovskite SmBaCo2O5+d, a potential cathode material for intermediate-temperature solid oxide fuel cells

The synthesis, conductivity properties, area specific resistance (ASR) and thermal expansion behaviour of the layered perovskite SmBaCo₂O_5+d (SBCO) are investigated for use as a cathode material for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The SBCO is prepared and shows the expected orthorhombic pattern. The electrical conductivity of SBCO exhibits a metal–insulator transition at about 200 °C. The maximum conductivity is 570 S cm⁻¹ at 200 °C and its value is higher than 170 S cm⁻¹ over the whole temperature range investigated. Under variable oxygen partial pressure SBCO is found to be a p-type conductor. The ASR of a composite cathode (50 wt% SBCO and 50 wt% Ce_0.9Gd_0.1O_2−d, SBCO:50) on a Ce_0.9Gd_0.1O_2−d (CGO91) electrolyte is 0.05 Ω cm² at 700 °C. An abrupt increase in thermal expansion is observed in the vicinity of 320 °C and is ascribed to the generation of oxygen vacancies. The coefficients of thermal expansion (CTE) of SBCO is 19.7 and 20.0 × 10⁻⁶ K⁻¹ at 600 and 700 °C, respectively. By contrast, CTE values for SBCO:50 are 12.3, 12.5 and 12.7 × 10⁻⁶ K⁻¹ at 500, 600 and 700 °C, that is, very similar to the value of the CGO91 electrolyte.     

Novel cobalt-free cathode materials BaCexFe1−xO3−δ for proton-conducting solid oxide fuel cells

A series of cobalt-free and low cost BaCe_xFe_1−xO_3−δ (x = 0.15, 0.50, 0.85) materials are successful synthesized and used as the cathode materials for proton-conducting solid oxide fuel cells (SOFCs). The single cell, consisting of a BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7)-NiO anode substrate, a BZCY7 anode functional layer, a BZCY7 electrolyte membrane and a BaCe_xFe_1−xO_3−δ cathode layer, is assembled and tested from 600 to 700 °C with humidified hydrogen (3% H₂O) as the fuel and the static air as the oxidant. Within all the cathode materials above, the cathode BaCe_0.5Fe_0.5O_3−δ shows the highest cell performance which could obtain an open-circuit potential of 0.99 V and a maximum power density of 395 mW cm⁻² at 700 °C. The results indicate that the Fe-doped barium cerates can be promising cathodes for proton-conducting SOFCs.     

Co-free, iron perovskites as cathode materials for intermediate-temperature solid oxide fuel cells

We have developed a Co-free solid oxide fuel cell (SOFC) based upon Fe mixed oxides that gives an extraordinary performance in test-cells with H₂ as fuel. As cathode material, the perovskite Sr_0.9K_0.1FeO_3−δ (SKFO) has been selected since it has an excellent ionic and electronic conductivity and long-term stability under oxidizing conditions; the characterization of this material included X-ray diffraction (XRD), thermal analysis, scanning microscopy and conductivity measurements. The electrodes were supported on a 300-μm thick pellet of the electrolyte La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ (LSGM) with Sr₂MgMoO₆ as the anode and SKFO as the cathode. The test cells gave a maximum power density of 680 mW cm⁻² at 800°C and 850 mW cm⁻² at 850 °C, with pure H₂ as fuel. The electronic conductivity shows a change of regime at T ≈ 350 °C that could correspond to the phase transition from tetragonal to cubic symmetry. The high-temperature regime is characterized by a metallic-like behavior. At 800 °C the crystal structure contains 0.20(1) oxygen vacancies per formula unit randomly distributed over the oxygen sites (if a cubic symmetry is assumed). The presence of disordered vacancies could account, by itself, for the oxide-ion conductivity that is required for the mass transport across the cathode. The result is a competitive cathode material containing no cobalt that meets the target for the intermediate-temperature SOFC.     

Thermal cycle stability of BaO–B2O3–SiO2 sealing glass

Thermal cycle stability is very important for glass seals in planar solid oxide fuel cell (pSOFC) applications. In the present study, thermal cycle stability of a thermally stable sealing glass is investigated using a sealing fixture from 150 °C to 700 °C. SS410 alloy with the TEC (thermal expansion coefficient) of 12.2 × 10⁻⁶ K⁻¹ (room temperature to 700 °C) is used to evaluate the effect of TEC mismatch on the thermal cycle stability. The leak rates increase with thermal cycles and appear to be two different stages. Microstructure examinations are performed to investigate the degradation mechanism of the thermal cycle stability. It is found that the sealing glass interacts chemically with the SS410 alloy and the formation of BaCrO₄ new phase results in the rapid increase of the leak rates.     

Characterization of Pr1−xSrxCo0.8Fe0.2O3−δ (0.2 ≤ x ≤ 0.6) cathode materials for intermediate-temperature solid oxide fuel cells

Cathode materials consisting of Pr_1−xSr_xCo_0.8Fe_0.2O_3−δ (x = 0.2–0.6) were prepared by the sol–gel process for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The samples had an orthorhombic perovskite structure. The electrical conductivities were all higher than 279 S cm⁻¹. The highest conductivity, 1040 S cm⁻¹, was found at 300 °C for the composition x = 0.4. Symmetrical cathodes made of Pr_0.6Sr_0.4Co_0.8Fe_0.2O_3−δ (PSCF)–Ce_0.85Gd_0.15O_1.925 (50:50 by weight) composite powders were screen-printed on GDC electrolyte pellets. The area specific resistance value for the PSCF–GDC cathode was as low as 0.046 Ω cm² at 800 °C. The maximum power densities of a cell using the PSCF–GDC cathode were 520 mW cm⁻², 435 mW cm⁻² and 303 mW cm⁻² at 800 °C, 750 °C and 700 °C, respectively.     

High performance layered SmBa0.5Sr0.5Co2O5+δ cathode for intermediate-temperature solid oxide fuel cells

The layered SmBa_0.5Sr_0.5Co₂O_5+δ (SBSC) perovskite oxide is synthesized by the Pechini method and investigated as a novel cathode material for intermediate-temperature solid oxide fuel cells (IT-SOFCs). A laboratory-sized Sm_0.2Ce_0.8O_1.9 (SDC)-based tri-layer cell of NiO–SDC/SDC/SBSC is operated from 500 to 700 °C fed with humidified H₂ (3% H₂O) as a fuel and the static ambient air as oxidant. A maximum power density of 1147 mW cm⁻² is achieved at 700 °C. The interfacial polarization resistance is as low as 1.01, 0.38, 0.16, 0.06 and 0.03 Ω cm² at 500, 550, 600, 650 and 700 °C, respectively. The experimental results indicate that SBSC is a very promising cathode material for IT-SOFCs.     

A high performance intermediate temperature fuel cell based on a thick oxide–carbonate electrolyte

A high performance intermediate temperature fuel cell (ITFC) with composite electrolyte composed of co-doped ceria Ce_0.8Gd_0.05Y_0.15O_1.9 (GYDC) and a binary carbonate-based (52 mol% Li₂CO₃/48 mol% Na₂CO₃), 1.2 mm thick electrolyte layer has been developed. Co-doped Ce_0.8Gd_0.05Y_0.15O_1.9 was synthesized by a glycine–nitrate process and used as solid support matrix for the composite electrolyte. The conductivity of both composite electrolyte and GYDC supporting substrate were measured by AC impedance spectroscopy. It showed a sharp conductivity jump at about 500 °C when the carbonates melted. Single cells with thick electrolyte layer were fabricated by a dry-pressing technique using NiO as anode and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ or lithiated NiO as cathode. The cell was tested at 450–550 °C using hydrogen as the fuel and air as the oxidant. Excellent performance with high power density of 670 mW cm⁻² at 550 °C was achieved for a 1.2 mm thick composite electrolyte containing 40 wt% carbonates which is much higher than that of a cell based on pure GYDC with a 70 μm thick electrolyte layer.     

Layered GdBa0.5Sr0.5Co2O5+δ as a cathode for intermediate-temperature solid oxide fuel cells

The layered GdBa_0.5Sr_0.5Co₂O_5+δ (GBSC) perovskite oxides are synthesized by Pechini method and investigated as a novel cathode material for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The single cell of NiO–SDC (Sm_0.2Ce_0.8O_1.9)/SDC (20 μm)/GBSC (10 μm) is operated from 550 to 700 °C fed with humidified H₂ as fuel and the static air as oxidant. An open circuit voltage of 0.8 V and a maximum power density of 725 mW cm⁻² are achieved at 700 °C. The interfacial polarization resistance is as low as 0.88, 0.29, 0.13 and 0.05 Ω cm² at 550, 600, 650 and 700 °C, respectively. The ratio of polarization resistance to total cell resistance decreases with the increase in the operating temperature, from 60% at 550 °C to 21% at 700 °C, respectively. The experimental results indicate that GBSC is a promising cathode material for IT-SOFCs.     

Stable, easily sintered BaCe0.5Zr0.3Y0.16Zn0.04O3−δ electrolyte-based protonic ceramic membrane fuel cells with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

A stable, easily sintered perovskite oxide BaCe_0.5Zr_0.3Y_0.16Zn_0.04O_3−δ (BCZYZn) as an electrolyte for protonic ceramic membrane fuel cells (PCMFCs) with Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode was investigated. The BCZYZn perovskite electrolyte synthesized by a modified Pechini method exhibited higher sinterability and reached 97.4% relative density at 1200 °C for 5 h in air, which is about 200 °C lower than that without Zn dopant. By fabricating thin membrane BCZYZn electrolyte (about 30 μm in thickness) on NiO–BCZYZn anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.00 V, a maximum power density of 236 mW cm⁻², and a low polarization resistance of the electrodes of 0.17 Ω cm² were achieved at 700 °C. This investigation indicated that proton conducting electrolyte BCZYZn with BSZF perovskite cathode is a promising material system for the next generation solid oxide fuel cells.     

Synthesis and assessment of La0.8Sr0.2ScyMn1−yO3−δ as cathodes for solid-oxide fuel cells on scandium-stabilized zirconia electrolyte

Perovskite-type La_0.8Sr_0.2Sc_yMn_1−yO_3−δ oxides (LSSMy, y = 0.0–0.2) were synthesized and investigated as cathodes for solid-oxide fuel cells (SOFCs) containing a stabilized zirconia electrolyte. The introduction of Sc³⁺ into the B-site of La_0.8Sr_0.2MnO_3−δ (LSM) led to a decrease in the oxides’ thermal expansion coefficients and electrical conductivities. Among the various LSSMy oxides tested, LSSM0.05 possessed the smallest area-specific cathodic polarization resistance, as a result of the suppressive effect of Sc³⁺ on surface SrO segregation and the optimization of the concentration of surface oxygen vacancies. At 850 °C, it was only 0.094 Ω cm² after a current passage of 400 mA cm⁻² for 30 min, significantly lower than that of LSM (0.25 Ω cm²). An anode-supported cell with a LSSM0.05 cathode demonstrated a peak power density of 1300 mW cm⁻² at 850 °C. The corresponding value for the cell with LSM cathode was 450 mW cm⁻² under the same conditions. The LSSM0.05 oxide may potentially be a good cathode material for IT-SOFCs containing doped zirconia electrolytes.     

High performance solid oxide fuel cell operating on dry gasified coal

A fluidized coal bed-solid oxide fuel cell (FB-SOFC) arrangement is employed for efficient conversion of dry gasified coal into electricity at 850 °C. It consists of an anode-supported tubular solid oxide fuel cell of 24 cm² active area coupled to a Boudouard gasifier. A minimally fluidized bed of low sulfur (0.15 wt%) Alaska coal is gasified at 930 °C by flowing CO₂ to generate CO. The resulting CO fuel is oxidized at the Ni/YSZ cermet anode. The highest cell power density achieved is 0.45 W cm⁻² at 0.64 V with 35.7% electrical conversion efficiency based on CO utilization. This power density is the highest reported in the literature for such systems and corresponds to a total power generation of 10.8 W by this cell. Similarly, 48.4% is the highest conversion efficiency measured at a power density of 0.30 W cm⁻² and 0.7 V. The open circuit voltages are in good agreement with values expected based on thermodynamic data.     

Effect of electrolytes on the photovoltaic performance of a hybrid dye sensitized ZnO solar cell

The efficiency of dye sensitized solar cell depends on the number of factors such as impedance due to anions in the electrolytes, oxidation–reduction process of anions and size of cations of the electrolyte. This paper reports the effect of electrolytes on the photovoltaic performance of hybrid dye sensitized ZnO solar cells based on Eosin Y dye. The size of the cations has been varied by choosing different electrolytes such as LiBr+Br₂, LiI+I₂, tetrapropylammonium iodide +I₂ in mixed solvent of acetronitrile and ethylene carbonate. The impedance of anions has been determined by electrochemical impedance spectra. It is observed that Br⁻/Br₃⁻ offers high impedance as compared to I⁻/I₃⁻ couple. The oxidation–reduction reactions of electrolytes are measured by linear sweep voltammogram. It is found that Br⁻/Br₃⁻ is more suitable than an I⁻/I₃⁻ couple in dye sensitized solar cell (DSSC) in terms of higher open-circuit photovoltage production and higher overall energy conversion efficiency. This is attributed to more positive potential of the dye sensitizer than that of Br⁻/Br₃⁻. The gain in V_oc was due to the enlarged energy level difference between the redox potential of the electrolyte and the Fermi level (E_f) of ZnO and the suppressed charge recombination as well.     

A potential interconnect material for solid oxide fuel cells: Nd0.75Ca0.25Cr0.98O3−δ

Chromium-deficient Nd_0.75Ca_0.25Cr_1−xO_3−δ (0.02 ≤ x ≤ 0.06) oxides are synthesized and assessed as a novel ceramic interconnect for solid oxide fuel cells (SOFCs). At room temperature, all the samples present single perovskite phase after sintering at 1600 °C for 10 h in air. Cr-deficiency significantly improves the electrical conductivity of Nd_0.75Ca_0.25Cr_1−xO_3−δ oxides. No structural transformation occurs in the Nd_0.75Ca_0.25Cr_1−xO_3−δ oxides in the temperature range studied. Among all the samples, the Nd_0.75Ca_0.25Cr_0.98O_3−δ sample with a relative density of 96.3% exhibits the best electrical conductivity of 39.0 and 1.6 S cm⁻¹ at 850 °C in air and hydrogen, respectively. The thermal expansion coefficient of Nd_0.75Ca_0.25Cr_0.98O_3−δ sample is 9.29 × 10⁻⁶ K⁻¹ in the temperature range from 30 to 1000 °C in air, which is close to that of 8 mol% yttria stabilized zirconia electrolyte (10.3 × 10⁻⁶ K⁻¹) and other cell components. The results indicate that Nd_0.75Ca_0.25Cr_0.98O_3−δ is a potential interconnect material for SOFCs.     

High performance of proton-conducting solid oxide fuel cell with a layered PrBaCo2O5+δ cathode

A dense BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) electrolyte is fabricated on a porous anode by in situ drop-coating method which can lead to extremely thin electrolyte membrane (10 μm in thickness). The layered perovskite structure oxide PrBaCo₂O_5+δ (PBCO) is synthesized by auto ignition process and initially examined as a cathode for proton-conducting IT-SOFCs. The electrical conductivity of PrBaCo₂O_5+δ (PBCO) reaches the general required value for the electrical conductivity of cathode absolutely. The single cell, consisting of PrBaCo₂O_5+δ (PBCO)/BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY)/NiO-BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) structure, is assembled and tested from 600 to 700 °C with humidified hydrogen (3% H₂O) as the fuel and air as the oxidant. An open-circuit potential of 1.01 V and a maximum power density of 545 mW cm⁻² at 700 °C are obtained for the single cell, and a low polarization resistance of the electrodes of 0.15 Ω cm² is achieved at 700 °C.     

Ni-Sm2O3 cermet anodes for intermediate-temperature solid oxide fuel cells with stabilized zirconia electrolytes

Ni-LnO_x cermets (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd), in which LnO_x is not an oxygen ion conductor, have shown high performance as the anodes for low-temperature solid oxide fuel cells (SOFCs) with doped ceria electrolytes. In this work, Ni-Sm₂O₃ cermets are primarily investigated as the anodes for intermediate-temperature SOFCs with scandia stabilized zirconia (ScSZ) electrolytes. The electrochemical performances of the Ni-Sm₂O₃ anodes are characterized using single cells with ScSZ electrolytes and LSM-YSB composite cathodes. The Ni-Sm₂O₃ anodes exhibit relatively lower performance, compared with that reported Ni-SDC (samaria doped ceria) and Ni-YSZ (yttria stabilized zirconia) anodes, the state-of-the-art electrodes for SOFCs based on zirconia electrolytes. The relatively low performance is possibly due to the solid-state reaction between Sm₂O₃ and ScSZ in fuel cell fabrication processes. By depositing a thin interlayer between the Ni-Sm₂O₃ anode and the ScSZ electrolyte, the performance is substantially improved. Single cells with a Ni-SDC interlayer show stable open circuit voltage, generate peak power density of 410 mW cm⁻² at 700 °C, and the interfacial polarization is about 0.7 Ω cm².