Friction and wear properties of bronze–graphite composite under water lubrication

Bronze–graphite composite was prepared using powder metallurgy. The friction and wear behaviors of the resulting composites in dry- and water-lubricated sliding against a stainless steel were comparatively investigated on an MM-200 friction and wear tester in a ring-on-block contact configuration. The wear mechanisms of the bronze–graphite composite were discussed based on examination of the worn surface morphologies of both the composite block and the stainless steel ring by means of scanning electron microscopy equipped with an energy dispersion spectrometry and on determination of some typical elements on the worn surfaces by means of X-ray photoelectron spectroscopy. It was found that the friction coefficient was higher under water lubrication than that under dry sliding and it showed margined change with increasing load under the both sliding conditions. A considerably decreased wear rate of the bronze–graphite composite was registered under water-lubricated sliding than under dry sliding, though it rose significantly at a relatively higher load. This was attributed to the hindered transfer of the composite onto the counterpart steel surface under water-lubricated sliding and the cooling effect of the water as a lubricant, while its stronger transfer onto the steel surface accounted for its higher wear rate under dry sliding. Thus, the bronze–graphite composite with much better wear-resistance under water-lubricated sliding than under dry sliding against the stainless steel could be a potential candidate as the tribo-material in aqueous environment.     

Tribological Property of Selective Laser Melting–Processed 316L Stainless Steel against Filled PEEK under Water Lubrication

Abstract

As a 3D printing technology, selective laser melting has remarkable advantages such as high processing flexibility, high material utilization, and short production cycle. The applications of selective laser melting technology in industry have become quite extensive. There are many tribological studies on selective laser melting materials, but few based on water lubrication (Zhu, et al., Journal of Zhejiang University-Science A, 19(2), pp 95–110). In this article, the tribological properties of 316L stainless steel processed by selective laser melting and traditional methods have been studied under water lubrication. Polyether ether ketone (PEEK) filled with carbon fiber (CF)/polytetrafluoroethylene (PTFE)/graphite was selected as the counterpart. 316L stainless steel and PEEK are a tribopair commonly used in water hydraulics. This study is of great significance to the application of selective laser melting material of tribopairs in water hydraulics. Friction and wear tests were carried out on a pin-on-disc contact test apparatus under different operating conditions. The friction coefficient, specific wear coefficient, scanning electron microscopy (SEM) of the worn surface, and energy-dispersive spectroscopy (EDS) of the surface adhesions of the three tribopairs were measured and compared. The results revealed that the friction coefficient of the selective laser melting (SLM) 316L stainless steel was significantly higher than that of traditionally processed (TP) 316L stainless steel, which might be caused by the pores on the surface of SLM 316L stainless steel. Adhesion and cutting on the surface of SLM 316L stainless steel were also more serious, resulting in a higher specific wear coefficient of its counterpart PEEK composite compared to PEEK composite against TP 316L stainless steel.     

Right Way of Using Graphene Oxide Additives for Water-Lubricated PEEK: Adding in Polymer or Water?

Water-lubricated polymer is attracting more and more interest from the industry. Adding nanoparticles is considered to be an effective way to improve the tribological performance. In this work, water-lubricated Polyetheretherketone (PEEK)-steel contacts were employed as the objects of study. A careful comparative study was made by investigating the effect of adding graphene oxide (GO) into water or into PEEK. Results show that adding GO into water can significantly reduce the wear and friction coefficient of pure PEEK, which is much more effective than adding GO into PEEK. Under the lubrication of GO aqueous dispersion, the wear of PEEK remains very low even under a harsh condition where the pressure reaches 50 MPa and the linear sliding speed is 0.7 m/s. Neat PEEK and GO/PEEK composites in pure water exhibit serious wear under this harsh condition. The excellent lubricating properties of GO aqueous dispersion are attributed to GO nanosheets entering into solid contacts, which can not only form a protective layer on steel counterpart repairing the worn surface, but also strongly adhere to the PEEK matrix resulting in an in situ-formed GO coating and prevent the scratch by steel counterpart.     

青铜-石墨热喷涂层在干摩擦和水润滑条件下的摩擦磨损性能

在MM-200摩擦磨损试验机上研究了青铜-石墨热喷涂层在干摩擦和水润滑条件下的摩擦磨损性能,采用扫描电镜(SEM)对磨损表面形貌进行了观测和采用X射线能谱分析(XPS)分析了涂层成分。结果表明,在水润滑条件下涂层摩擦因数和磨损率均低于干摩擦条件下;在水润滑条件下磨损机制为轻微磨粒磨损和犁削磨损,在干摩擦下主要是较为严重的粘着磨损和犁削。这是由于水润滑降低了摩擦副界面温度,提高了石墨润滑膜的韧性,改善了润滑效果,从而阻止了粘着磨损的发生,水还促进了钢偶件表面致密氧化膜的形成,从而减轻磨损。因此水润滑对涂层磨损性能有较大影响。     

Comparative investigation on the tribological behaviors of CF/PEEK composites under sea water lubrication

Carbon fiber (CF) reinforced polyetheretherketone (PEEK) composites were prepared and their tribological behaviors under sea water lubrication were comparatively investigated. The results showed that the incorporation of CF can greatly improve the wear resistance of PEEK under sea water lubrication, especially when the volume fraction of CF was about 10%, because exposed CF can effectively share the main load between the contact surfaces and consequently protect the matrix from severe wear. In addition, CF/PEEK had better friction and wear properties under sea water lubrication than under dry friction and pure water lubrication due to better lubricating effect of sea water.     

Friction and wear of polyphenylene sulfide composites filled with micro and nano CuO particles in water-lubricated sliding

The tribological behavior of polyphenylene sulfide (PPS) composites filled with micro and nano CuO particles in water-lubricated sliding condition were studied. Pin-on-disk sliding tests were performed against a steel counterface of surface roughness 0.09–0.11 μm. The lubrication regimes were established from friction data corresponding to various combinations of loads and sliding speeds. Later experiments were performed using the sliding speed of 0.5 m/s and contact pressure of 1.95 MPa, which corresponded to boundary lubrication regime. Micro CuO particles as the filler were effective in reducing the wear of PPS but nano CuO particles did not reduce wear. The steady state wear rate of PPS-30 vol.% micro CuO composite was about 10% of that of unfilled PPS and the coefficient of friction in this case was the lowest. The examination of the topography of worn pin surfaces of nano CuO-filled PPS by SEM revealed grooving features indicating three-body abrasion. The transfer films formed on the counterfaces during sliding were studied by optical microscopy and AFM. The wear behavior of the composites in water-lubricated sliding is explained using the characteristics of worn pin surfaces and transfer films on the counterface.     

Tribological Behaviors of Carbon Fiber–Reinforced PEEK Sliding on Ion-Nitrided 2Cr13 Steel Lubricated with Tap Water

Selecting the proper material and surface treatment methods for elements is one of the essential problems when designing water hydraulic components due to the corrosiveness and poor lubricity of water. Experimental investigation was performed to study the tribological properties of ion-nitrided 2Cr13, a kind of martensitic stainless steel, sliding on carbon fiber–reinforced polyetheretherketone (CFRPEEK). The influence of factors such as sliding velocity, load, and lubrication condition were studied through experiments mainly under tap water lubrication. It was found that the friction coefficients are influenced by both the pressure and the sliding velocity. In contrast, the friction coefficients between quenched 2Cr13 and CFRPEEK are much higher. Compared to water lubrication, both the wear rate and friction coefficients increase in the case of dry friction. Wear mainly occurred on the CFRPEEK. By examining the worn surfaces of the specimens, it was found that adhesion was the main form of wear of the PEEK composite.     

Friction and Wear Behaviors of Several Polymers Sliding Against GCr15 and 316 Steel Under the Lubrication of Sea Water

Ocean tribology, a new research field of tribology, is currently being established and developed. The tribological behaviors of polyether ether ketone (PEEK), poly(phenyl p-hydroxybenzoate) (PHBA), polyimide (PI), and perfluoroethylene propylene copolymer (FEP) sliding against GCr15 and 316 steel rings under the lubrication of sea water were studied and compared with that under the lubrication of pure water. The results show that the friction and wear behaviors of a polymer under the lubrication of aqueous medium are not only related to the properties of polymer itself, but also to the corrosive effect and lubricating effect of the medium. When a polymer slid against GCr15 steel under sea water lubrication, the friction coefficient and wear rate of polymer were much larger than that under pure water lubrication because of indirect corrosive wear. However, when sliding against corrosion-resistant 316 steel, polymers PEEK, FEP, and PI exhibited lower coefficients of friction and wear rates under sea water lubrication, this was attributed to better lubricating effect of sea water as a result of the deposition of CaCO₃ and Mg(OH)₂ on the counterface. On the contrary, the friction coefficient and wear rate of PHBA sliding against 316 steel under sea water lubrication were larger than that under pure water lubrication, which may be related to the properties of PHBA itself.     

Synergetic Effect of Lubricant Additive and Reinforcement Additive on the Tribological Behaviors of PEEK-Based Composites under Seawater Lubrication

Polyetheretherketone (PEEK)-based composites reinforced with lubricant additive (polytetrafluoroethylene, PTFE) and reinforcement additives including carbon fiber (CF), glass fiber (GF), and bronze powder were prepared using a hot-press molding technique. The synergetic effects of different additives on the tribological behaviors of PEEK-based composites sliding against 316 steel under seawater lubrication were investigated systematically using a ring-on-block test rig. The results showed that lubricant additive PTFE can decrease the friction coefficient and consequently improved the wear resistance of PEEK under seawater lubrication, especially when the volume fraction of PTFE was about 20%. It was also found that the incorporation of CF can further improve the wear resistance of PEEK blended with 20% PTFE, especially under high load and high sliding speed. This suggested that a synergistic effect on improving the wear resistance of PEEK existed between PTFE and CF, which originated from good lubrication of PTFE, good reinforcement of CF, and good interfacial combination between CF and PEEK-20%PTFE. However, two other reinforcement additives of GF and bronze powder had an antagonistic effect but not a synergetic effect with PTFE; that is, the incorporation of the two additives greatly deteriorated the wear resistance of PEEK blended with 20% PTFE.     

The Effect of Different Temperatures on Friction and Wear Properties of CFRPEEK against AISI 431 Steel under Water Lubrication

The tribological behavior of 30 vol% carbon fiber–reinforced polyetheretherketone (CFRPEEK) against AISI 431 steel under different temperatures of water lubrication was investigated. Friction and wear tests were carried out on a disc-on-disc contact test apparatus under different operating conditions. The results reveal that the lubricant temperature has a significant effect on the friction and wear properties of CFRPEEK sliding against AISI 431 steel. The average friction coefficient and wear rate of CFRPEEK increase with increasing lubricant temperature. However, the wear rate of AISI 431 steel did not have a positive correlation with the wear rate of CFRPEEK under different temperatures of water lubrication. Moreover, the original and worn surfaces of CFRPEEK and AISI 431 steel were imaged by environmental scanning electron microscopy and optical microscopy, respectively. The main tribological mechanisms of CFRPEEK sliding against AISI 431 steel were adhesive wear, and increasing the temperature of the lubricant could accelerate wear.     

水润滑下316L不锈钢与聚醚醚酮摩擦磨损性能研究

为了寻找适合于水液压泵/马达的摩擦副材料,以316 L不锈钢与纯聚醚醚酮树脂、30%玻璃纤维增强PEEK(PEEKGF30)、30%碳纤维增强PEEK(PEEKCA30),PTFE和石墨及碳纤维填充PEEK(PEEKHPV)组成的摩擦副为研究对象,利用MMW-1立式万能摩擦磨损试验机测量摩擦副在水润滑下接触表面的摩擦因数和温度以及试样的磨损量,并通过激光共聚焦显微镜对试件表面磨损形貌进行分析。结果表明:316 L-PEEKHPV摩擦副的摩擦因数、摩擦温升、磨损量均小于其余3组摩擦副,适合作为水液压泵/马达的关键摩擦副材料。316 L不锈钢与PEEKGF30配对时,摩擦机制为涂抹和擦伤,磨损较为严重;与PEEKCA30配对时,摩擦机制为擦伤;与PEEKHPV配对时摩擦机制主要为划伤,磨损较为轻微。     

模拟矿井环境下的PEEK/SiO2/CF-MoS2复合材料摩擦行为研究*

为改善聚醚醚酮（PEEK）在矿井工况下的摩擦性能,选用纳米二氧化硅（SiO2）、二硫化钼（MoS2）和短切碳纤维（CF）为增强填料制备PEEK/SiO2/CF-MoS2复合材料,并探究PEEK/SiO2/CF-MoS2复合材料在不同工况条件下的滑动与滚动摩擦学性能;通过模拟滚轮罐耳在矿井环境下的运行方式,分析其磨损形貌和磨损机制。结果表明：PEEK/SiO2/CF-MoS2复合材料在不同载荷条件下均具有良好的减摩和耐磨特性;滑动摩擦在水介质工况下及滚动摩擦在干摩擦工况下,复合材料的摩擦因数和磨损率最低,其磨损机制均以磨粒磨损为主。与矿井常用的聚氨酯材料的对比,PEEK/SiO2/CF-MoS2复合材料的摩擦学性能更为优异。     

纳米粒子及PTFE填充PEEK复合材料摩擦特性的载荷和时间依赖性

以热压成型法制备了纳米Al2O3和纳米TiO2分别与聚四氟乙烯(PTFE)填充PEEK复合材料,利用自制销-盘摩擦磨损试验机研究了干摩擦条件下复合材料的摩擦行为。结果表明：复合材料的摩擦因数依赖于材料中纳米粒子的种类和含量,并对载荷有明显的依赖性;当纳米Al2O3的质量分数为5％～7％时,PEEK复合材料的摩擦因数和比磨损率最低;随着外加载荷的变化,摩擦因数呈现一定的变化规律。     

UHMWPE基水润滑轴承摩擦及润滑特性的试验研究

针对纤维填料改性UHMWPE水润滑轴承的摩擦磨损性能进行研究。在平面摩擦磨损试验机上对玻璃纤维及碳纤维填料对UHMWPE复合材料摩擦性能进行试验,并分析GF-CF-UHMWPE材料与Thordon SXL材料在干摩擦、水润滑工况下的摩擦因数及磨损量。最后,采用径向水润滑轴承试验台对比研究了GF-CF-UHMWPE轴承和Thordon SXL轴承在不同载荷下摩擦因数随转速的变化规律。结果表明:纤维填料能显著增强UHMWPE的减摩性和耐磨性,GF-CF-UHMWPE材料具有更好的耐温性能,线性热膨胀系数也显著减小;GF-CF-UHMWPE轴承具有相同载荷下启动转速低,启动摩擦因数小的特性。     

Tribological behavior of PEEK-based materials under mixed and boundary lubrication conditions

In modern industries, more and more mechanical components are exposed to mixed and even boundary lubrication conditions, inducing fast wear and even scuffing of the motion systems. In order to enhance the lifetime and reliability of the motion systems, replacing metal–metal friction pairs by metal–polymer ones can be one of the most effective approaches. The present work focuses on tribological behavior of pure polyetheretherketone (PEEK) and a formulated PEEK composite lubricated with diesel and engine oil. It was demonstrated that in mixed and boundary lubrication regimes the structure of PEEK materials affect significantly the tribological performance. Formation of a tribofilm on the surface of metallic counterbody plays an important role on the tribological behavior of the PEEK-based materials.     

Sensitivity of μ of Friction Materials to Load and Speed under Dry Sliding and Water Lubricated Conditions

The tribological behavior of friction materials is complex under various operating conditions. The present article discusses the sensitivity of tribological behaviors of friction materials to load and speed under dry and water-lubricated conditions qualitatively and μ of values was also analyzed quantitatively based on regression analysis. The friction and wear behaviors of friction materials were evaluated on a ring-on-block-type test rig. It was observed that the material itself was the dominant factor in μ sensitivity of friction materials, followed by sliding speed. The influence of the interaction of load and speed was negligible under water-lubricated condition. The friction coefficient of the composite was less sensitive to operating parameters under water-lubricated condition.     

聚四氟乙烯碳纤维增强双马来酰亚胺复合材料的摩擦学性能

研究了不同含量PTFE碳纤维增强双马来酰亚胺复合材料的力学和摩擦学性能,并分析了在干摩擦和水润滑条件下的磨损表面形貌和磨损机制。结果表明:添加质量分数10%~15%PTFE的复合材料体系机械性能最佳,随PTFE含量的增加,复合材料的摩擦因数下降,而磨损率呈上升趋势。水润滑下,摩擦因数和磨损率比干摩擦下都有相应的降低。干摩擦下,材料的磨损主要以塑性变形、微观破裂及破碎为主;水润滑下,这一机制明显减弱,主要表现为微切削形态。     

The effect of stainless steel structure on the performance of rubber-graphite under conditions of water lubrication

A new sliding bearing material based on rubber filled with different graphites was assessed against stainless steels of various structures under conditions of water lubrication in an Amsler machine. The tribological characteristics of the rubber-graphite depend upon the fillers used. The wear of stainless steel journals depends upon the material structure and the chromium carbide present.     

Effect of UHMWPE Microparticles on the Tribological Performances of High-Strength Glass Fabric/Phenolic Laminate Composites Under Water Lubrication

The tribological behaviors of ultra-high molecular weight polyethylene (UHMWPE) microparticle-modified high-strength glass fabric/phenolic laminate composites sliding against stainless steel under water lubrication have been investigated. Results showed that the incorporation of UHMWPE microparticles, especially at the mass fraction of 5.0 %, improved the wear resistance of the laminate composite to a significant extent, because UHMWPE microparticle can effectively absorb and dissipate the friction energy through a plastic deformation during the formation of the regular ripple-like abrasion patterns on its worn surface. During the sliding process, after the phenolic resin was firstly worn off, UHMWPE microparticles with much better wear resistance were protruded from the worn surface of the laminate composite, leading to a fundamental change in the contact status of the matched surfaces from rigid resin and fibers/steel to flexible UHMWPE/steel. As a result, low and steady friction coefficient was obtained due to good adaptability of UHMWPE to water lubrication.     

Tribological behaviours of PA/UHMWPE blend under dry and lubricating condition

Dry-sliding and lubricated friction and wear behaviours of polyamide (PA) and ultra-high molecular weight polyethylene (UHMWPE) blend were studied using a pin-on-disc method (polymer pin sliding against a stainless steel disc) at room environment. The tribological performance of PA and UHMWPE were also investigated for the purpose of comparison. The worn surfaces were examined using a scanning electron microscope (SEM) and optical microscope. It was observed that PA specimen demonstrated highest friction coefficient, UHMWPE the lowest in both dry-sliding and lubricated sliding test. The friction of PA could be sufficiently decreased by blending with UHMWPE. Statistical analysis suggested the relationship between the wear volume loss and the sliding distance could be expressed by a linear model for dry-sliding, while a logarithmic model was determined for lubricated sliding. The difference in wear modes between both sliding series suggested that there was change in the mode of material removal process. The lower wear rate in lubricated sliding was attributed to the elastohydrodynamic or partial elastohydrodynamic lubrication through the development of a continuous lubricant film between the polymer and the counterface, while the high wear rate of the specimens, in dry-sliding test, was mainly caused by fatigue process due to the repeated action of tearing and crack-propagation.