Impedance and modulus analysis of the (Na0.6Ag0.4)2PbP2O7 compound

The electrical properties of the (Na_0.6Ag_0.4)₂PbP₂O₇ compound were studied using the complex impedance spectroscopy in the temperature range (502-667 K). Grain interior, grain boundary and electrode-material interface contributions to the electrical response are identified by the analysis of complex plan diagrams. The imaginary part of the modulus at several temperatures shows a double relaxation peaks, furthermore suggesting the presence of grains and grain boundaries in the sample. An analysis of the dielectric constants ?′, ?″ and loss tangent tan(δ) with frequency shows a distribution of relaxation times. The dc conductivity of the material is thermally activated with an activation energy about 0.8 eV which is in the vicinity of the that obtained from tan(δ) (E = 0.7 eV) and modulus (E_m = 0.68 eV) studies.     

High temperature thermoelectric properties and energy transfer devices of Ca3Co4−xAgxO9 and Ca1−ySmyMnO3

The high temperature oxide thermoelectric materials of p-type Ca₃Co_4−xAg_xO₉ (denoted as p-Co349/Ag_x) and n-type Ca_1−ySm_yMnO₃ (denoted as n-Mn113/Sm_y) were prepared by the self-ignition method combined with a sintering technique. The influence of doping Ag and Sm on the thermoelectric properties of the corresponding materials was evaluated. The figures of merit, ZT, for the p-Co349/Ag_0.2 and n-Mn113/Sm_0.02 materials reached maxima of 0.20 and 0.15 at 973 K, respectively. The performances of thermoelectric devices constructed with the p- and n-type pairs were evaluated in terms of the maximum output power (P_max) and manufacturing factor. The P_max and volume power density for the four-leg devices reached 36.8 mW and 81.9 mW cm⁻³ at ΔT of 523 K, respectively.     

High permittivity and low dielectric loss of the Ca1−xSrxCu3Ti4O12 ceramics

The Ca_1−xSr_xCu₃Ti₄O₁₂ (CSCTO) giant dielectric ceramics were prepared by conventional solid-state method. X-ray diffraction patterns revealed that a small amount of Sr²⁺ (x < 0.2) had no obvious effect on the phase structure of the CSCTO ceramics, while with increasing the Sr²⁺ content, a second phase of SrTiO₃ appeared. Electrical properties of CSCTO ceramics greatly depended on the Sr²⁺ content. The Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics exhibited a higher permittivity (71,153) and lower dielectric loss (0.022) when measured at 1 kHz at room temperature. The ceramics also performed good temperature stability in the temperature range from −50 °C to 100 °C at 1 kHz. By impedance spectroscopy analysis, all compounds were found to be electrically heterogeneous, showing semiconducting grains and insulating grain boundaries. The grain resistance was 1.28 Ω and the grain boundary resistance was 1.31 × 10⁵ Ω. All the results indicated that the Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics were very promising materials with higher permittivity for practical applications.     

Transport mechanism in a ceramic system: LiCo3/5Fe1/5Cu1/5VO4

The electrical impedance and modulus properties of a LiCo_3/5Fe_1/5Cu_1/5VO₄ ceramic system were measured by impedance spectroscopy method in the frequency range 10²-10⁶ Hz and temperature range 22-250 °C. X-ray diffraction study reveals formation of the compound in a cubic crystal system with lattice parameters a = 8.2756 (3) Å. Field emission scanning electron microscopy is used to investigate the grain morphology of the material. Nyquist plots confirm the existence of bulk and grain boundary effects at 22 °C ≤ T ≤ 200 °C, and bulk, grain boundary and polarization effects at T ≥ 225 °C. Electrical modulus study indicates a non-Debye behavior of the material. A detailed study of bulk conductivity shows electric conduction in the material as a thermally activated process.     

Effect of the sintering temperature on the properties of nanocrystalline Ca1−xSmxMnO3 (0 ≤ x ≤ 0.4) powders

Nanocrystalline Ca_1−xSm_xMnO₃ (0 ≤ x ≤ 0.4) manganites were prepared by a soft chemical method (Pechini method) followed by auto-combustion and sintering in air at 1073 or 1473 K. Single-phase powders with general composition Ca_1−xSm_xMnO₃ were obtained after 18 h annealing. The particle and grain sizes of the substituted Sm-manganites did not exhibit variation with samarium content, but increase with increasing the sintering temperature. All manganites show two active IR vibrational modes near 400 and 600 cm⁻¹ characteristic of the BO₆ octahedron vibrations.For the samples sintered at T_s = 1473 K, the partial substitution of calcium by samarium in the CaMnO₃ phase induces a marked decrease in the electrical resistivity, in the temperature range of 300-900 K, and at the same time a metal-to-insulator transition occurs; for T_s = 1073 K all the samples present semiconductor behaviour. With the increase of the annealing temperature the grain size increases and a metal-semiconductor transition appears. The results can be ascribed to the Mn⁴⁺/Mn³⁺ ratio and particle grain size. The effects of particle size on the electrical properties can be attributed to the domain status, changes in the Mn-O-Mn bond angle and Mn-O bond length.     

Origin of giant dielectric constant in Ba[(Fe1−xCox)1/2Nb1/2]O3

The X-ray diffraction Rietveld refinement of Ba[(Fe_1−xCo_x)_1/2Nb_1/2]O₃ with 0 ≤ X ≤ 1 shows cubic structure formation with space group P_m3_m. No distinct tilting of oxygen octahedron is observed. The dielectric measurement of such a cubic system exhibited giant values (?′ > 10⁴) in the temperature range of 298-483 K and frequency range of 10²-10⁵ Hz. An analysis of the permittivity, electric modulus, and electrical conductivity properties in these systems confirmed the presence of oxygen vacancies induced dipolar relaxation. Our investigations show that the observed extremely high dielectric constant values are predominantly the result of oxygen vacancies induced dipoles produced at the grain boundaries. Additional significant intrinsic contributions to the permittivity comes from the directly doped electrons at the unit cell, as indicated by the enhancement in the observed values of the permittivity on replacement of Fe³⁺ (3d⁵) by Co³⁺ (3d⁶). The contributions of the doped free charges and the oxygen vacancy induced dipoles are separated using the Jump Relaxation Model.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Study of structural, dielectric and electrical behavior of (1 − x)Ba(Fe0.5Nb0.5)O3-xSrTiO3 ceramics

Polycrystalline samples of BaFe_0.5Nb_0.5O₃ and (1 − x)Ba(Fe_0.5Nb_0.5)O₃-xSrTiO₃ [referred as BFN and BFN-ST respectively] (x = 0.00, 0.15 and 0.20) have been synthesized by a high-temperature solid-state reaction technique. The XRD patterns of the BFN and BFN-ST at room temperature show a monoclinic phase. The microstructure of the ceramics was examined by the scanning electron microscopy (SEM) and shows the polycrystalline nature of the samples with different grain sizes, which are inhomogeneously distributed through the sample surface. Detailed studies of dielectric and impedance properties of the materials in a wide range of frequency (100 Hz-5 MHz) and temperatures (30-270 °C) showed that properties are strongly temperature and frequency dependent. Complex Argand plane plot of ?″ against ?′, usually called Cole-Cole plots is used to check the polydispersive nature of relaxation phenomena in above mentioned compounds. Relaxation phenomena of non-Debye type have been observed in the BFN and BFN-ST ceramics, as confirmed by the Cole-Cole plots.     

Mo microalloying effect on the glass-forming ability, magnetic, mechanical and corrosion properties of (Fe0.76Si0.096B0.084P0.06)100-xMox bulk glassy alloys

The effect of Mo addition on the glass-forming ability (GFA), magnetic properties, mechanical properties and corrosion resistance of (Fe_0.76Si_0.096B_0.084P_0.06)_100−xMo_x (x = 0, 2, 4 and 6 at.%) bulk glassy alloys (BGAs) with high Fe contents was investigated. The 2 at.% Mo addition makes the alloy composition approach towards a eutectic point, which could result in an increase in the GFA. The BGA rod with diameters up to 3.5 mm was produced by copper mold casting. These BGAs exhibit a rather high saturation magnetization of 0.98-1.51 T and lower coercive force of 1.7-2.1 A/m. A significant improvement in corrosion resistance was observed with microalloying Mo element in 1 N H₂SO₄ solution. Furthermore, these Fe-based BGAs show super-high strength of ∼3.3 GPa and Young's modulus of 200 GPa.     

Photoluminescent properties of LiSrxBa1−xPO4:RE (RE = Sm, Eu) f-f transition phosphors

Rare-earth ions (Sm³⁺ or Eu³⁺) doped LiSr_xBa_1−xPO₄ (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) f-f transition phosphor powders were prepared by a high temperature solid-state reaction. The resulted phosphors were characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. The results of XRD indicate that the phase structure of the sample changes from LiBaPO₄ to LiSrPO₄ when x changes from 0 to 1.0. The excitation spectra indicate that only direct excitation of rare earth ions (Sm³⁺ or Eu³⁺) can be observed. The doped rare earth ions show their characteristic emission in LiSr_xBa_1−xPO₄, i.e., Eu³⁺⁵D₀-⁷F_J (J = 0, 1, 2, 3, 4), Sm³⁺⁴G_5/2 → ⁶H_J (J = 5/2, 7/2, 9/2, 11/2), respectively. The dependence of the emission intensities of the LiSr_xBa_1−xPO₄:Sm³⁺ and LiSr_xBa_1−xPO₄:Eu³⁺ phosphors on the x value and Ln³⁺ (Ln³⁺ = Sm³⁺, Eu³⁺) concentration is also investigated.     

Effect of Dy on the properties of Sm-doped ceria electrolyte for IT-SOFCs

Co-doped ceria-based electrolytes of Ce_0.8Sm_0.2−xDy_xO_2−δ (x = 0, 0.02, 0.06, 0.10, 0.14) were sintered from powders obtained by solid state reaction method. The phase identification, thermal expansion, ionic conductivities and microstructures of samples were studied by X-ray diffraction (XRD), dilatometry, AC impedance spectroscopy (IS) and scanning electron microscopy (SEM). The results showed that the addition of Dy led to higher ionic conductivity and lower activation energy in comparison with Sm singly doped ceria Ce_0.8Sm_0.2O_2−δ (SDC) in the temperature range of 300-800 °C. As the addition amount of Dy increased up to 2 mol% (Ce_0.8Sm_0.18Dy_0.02O_2−δ), the sample attained the highest ionic conductivity, about 50% higher than that of SDC at 500 °C. The effect of Dy on the grain boundary conductivity was more apparent than that of the bulk conductivity. XRD measurements indicated that all the samples were single phase. The thermal expansion was linear for all the samples. The addition of Dy did not change the thermal expansion coefficient (TEC) significantly.     

Preparation, structure and electrical conductivity of the pyrochlore-type phase Sm2Zr2O7 codoped with bivalent magnesium and trivalent dysprosium cations

The pyrochlore-type phases with the compositions of SmDy_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.20) have been prepared by pressureless-sintering method for the first time as possible solid electrolytes. The structure and electrical conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics have been studied by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance spectroscopy measurements. SmDy_1−xMg_xZr₂O_7−x/2 (x = 0, 0.05, 0.10) ceramics exhibit a single phase of pyrochlore-type structure, and SmDy_1−xMg_xZr₂O_7−x/2 (x = 0.15, 0.20) ceramics consist of pyrochlore phase and a small amount of the second phase magnesia. The total conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics obeys the Arrhenius relation, and the total conductivity of each composition increases with increasing temperature from 673 to 1173 K. SmDy_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest total conductivity value is about 8 × 10⁻³ S cm⁻¹ at 1173 K for SmDy_1−xMg_xZr₂O_7−x/2 ceramics.     

Fabrication and properties of Ba(Zr1−xCex)0.9Y0.1O2.95/NaCl composite electrolyte materials

Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95/NaCl (x = 0.1, 0.2 and 0.3) composite electrolyte materials were fabricated with ZnO as sintering aid. The effect of ZnO on the properties of Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 matrix were investigated. The phase composition and microstructure of samples were characterized by XRD and SEM, respectively. The electrochemical performances were studied by three-probe conductivity measurement and AC impedance spectroscopy. XRD results showed that Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 with 2 mol% of ZnO was perovskite structure. The relative density of this sample was above 95% when sintered at 1450 °C for 6 h. By adding 10 mol% of NaCl to Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 with 2 mol% of ZnO that was sintered at 1400 °C for 6 h, the conductivity was increased. The electrical conductivity of 1.26 × 10⁻² S/cm and activation energy of 0.23 eV were obtained when tested at 800 °C in wet hydrogen.     

High frequency response to the impedance complex properties of Nb-doped CaCu3Ti4O12 electroceramics

Impedance analyses was performed on undoped and Nb-doped CaCu₃Ti₄O₁₂ (CaCu₃Ti_4−xNb_xO_12+x/2; x = 0, 0.01, 0.03, 0.05, 0.1) to investigate their electrical properties. The pellet samples were prepared using the solid state reaction method. Silver electrode was deposited on both pellets’ surfaces for electrical measurement. The thermally etched samples showed tiny bumped domains within the grains. The existence of both domain and grain boundaries are believed to strongly influence the dielectric constant of CaCu₃Ti₄O₁₂ (CCTO). Undoped CCTO showed two arcs of impedance complex plane while Nb-doped samples have three arcs. Each arc represents the constituent elements of the CCTO. The highest frequency arc is evidence that CCTO consists of conductive domains which measure about 1 Ω and are insulated by two types of barriers, i.e. domain boundary and grain boundary.     

Microwave dielectric properties of (Zn1−xMgx)TiO3 (ZMT) ceramics for dielectric resonator antenna application

Present investigation provides experimental studies on cylindrical dielectric resonator antennas (CDRAs) fabricated from (Zn_1−xMg_x)TiO₃ (ZMT) ceramic material with different substitution of Mg in place of Zn (x = 0.1, 0.2, 0.3, 0.4 and 0.5) along with measurement of material permittivity in C-band of microwave frequencies. The dielectric properties of the ZMT ceramic materials with different x values (x = 0.1-0.5) have been measured at microwave frequencies using Hakki-Coleman method modified by Courtney. The value of dielectric constant and loss tangent decreases with the increase in Mg content. The dielectric constant is minimum for x = 0.3 and loss tangent is minimum for x = 0.5. The variations of return loss and input impedance versus frequency and radiation patterns of CDRAs at their respective resonant frequencies are studied experimentally. The measured results for resonant frequency and return loss bandwidth of the CDRAs are also compared with theoretical ones. The measured resonant frequencies of all the four CDRAs are nearly in agreement with respective theoretical values and the values of input resistance at respective resonant frequencies of the CDRAs match well with the coaxial feed impedance of 50 Ω. The designed CDRAs have broad beam, low side lobe and cross-polarized lobe levels.     

Electrical properties of binder-free thick film BaYxBi1−xO3 NTC thermistors

The microstructure and electrical properties of BaY_xBi_1−xO₃ thick film negative temperature coefficient thermistors, fabricated by screen printing, were investigated. The sintered thick films were the single-phase solid solutions of the BaY_xBi_1−xO₃ compounds with a monoclinic structure. The added Y₂O₃ led to a significant decrease in the grain size of the thermistors. The resistivity and coefficient of temperature sensitivity for the BaY_xBi_1−xO₃ (0 ≤ x ≤ 0.15) thick film NTC thermistors decreased first with increasing x in the range of x < 0.04 and then increased with further increase in x.     

Magnetomechanical properties of epoxy-bonded Sm1−xNdxFe1.55 (0 ≤ x ≤ 0.56) pseudo-1-3 magnetostrictive particulate composites

Pseudo-1-3 magnetostrictive particulate composites consisting of light rare earth (Sm and Nd)-based magnetostrictive Sm_1−xNd_xFe_1.55 particles with the Nd content x of 0-0.56 and randomly distributed sizes of 10-180 μm embedded and aligned in a passive epoxy matrix are fabricated using the particulate volume fraction of 0.5. The quasistatic magnetomechanical properties of the composites are investigated and the results are compared with their monolithic alloys for various x. The composites exhibit similar qualitative trends in properties with the alloys for all x. The Sm_0.92Nd_0.08Fe_1.55 composite shows a large unsaturated magnetostriction λ of −530 ppm at 500 kA/m and a high piezomagnetic coefficient d₃₃ of −2.0 nm/A at 100 kA/m as a result of the magnetocrystalline anisotropy compensation between Sm³⁺ and Nd³⁺ ions in the Sm_0.92Nd_0.08Fe_1.55 alloy.     

Effects of Mn substitution on ferro- and piezoelectric properties of Bi0.86Sm0.14FeO3 thin films

The Bi_0.86Sm_0.14FeO₃ (BSFO) and Bi_0.86Sm_0.14Fe_1 − xMn_xO₃ (BSFMO) (x = 0.01, 0.03, 0.05) thin films were deposited on indium tin oxide/glass substrates via a metal organic deposition method. 1 at.% Mn doping leads to an evident reduction of the leakage current in BSFO film. More importantly, the Bi_0.86Sm_0.14Fe_0.99Mn_0.01O₃ film exhibits the lowest coercive field (E_c = 272 kV/cm), the largest remanent polarization (P_r = 53.6 μc/cm²) and the remanent out-of-plane piezoelectric coefficient (d₃₃ = 146 pm/V). However, further increase of Mn doping content results in the deterioration of the charge retaining capability and the piezoelectric properties of the films. The negative influence of high Mn doping contents was discussed based on the structure change and the contribution of irreversible movement of non-180° domain walls in the aged films.     

Structural, elastic and electronic properties of Mg(Cu1−xZnx)2 alloys calculated by first-principles

The structural, elastic and electronic properties of Mg(Cu_1−xZn_x)₂ alloys (x = 0, 0.25, 0.5,and 0.75) were investigated by means of first-principle calculations within the framework of density functional theory (DFT). The calculation results demonstrated that the partial substitution of Cu with Zn in MgCu₂ leaded to an increase of lattice constants, and the optimized structural parameters were in very good agreement with the available experimental values. From energetic point of view, it was found that with increase of Zn content the structural stability of Mg(Cu_1−xZn_x)₂ alloys decreased apparently. The single-crystal elastic constants were obtained by computing total energy as a function of strain, and then the bulk modulus B, shear modulus G, Young's modulus Y and Poisson's ratio ν of polycrystalline aggregates were derived. The calculated results showed that among the Mg(Cu_1−xZn_x)₂ alloys, MgCuZn exhibited the largest stiffness, while Mg₂Cu₃Zn showed the best ductility. Finally, the electronic density of states (DOSs) and charge density distribution were further studied and discussed.