Effect of humidity of reactants on the cell performance of PEM fuel cells with parallel and interdigitated flow field designs

This study investigates the effects of the relative humidity (RH) of the reactants on the cell performance and local transport phenomena in proton exchange membrane fuel cells with parallel and interdigitated flow fields. A three-dimensional model was developed taking into account the effect of the liquid water formation on the reactant transport. The results indicate that the reactant RH and the flow field design all significantly affect cell performance. For the same operating conditions and reactant RH, the interdigitated design has better cell performance than the parallel design. With a constant anode RH = 100%, for lower operating voltages, a lower cathode RH reduces cathode flooding and improves cell performance, while for higher operating voltages, a higher cathode RH maintains the membrane hydration to give better cell performance. With a constant cathode RH = 100%, for lower operating voltages, a lower anode RH not only provides more hydrogen to the catalyst layer to participate in the electrochemical reaction, but also increases the difference in the water concentrations between the anode and cathode, which enhances back-diffusion of water from the cathode to the anode, thus reducing cathode flooding to give better performance. However, for higher operating voltages, the cell performance is not dependent on the anode RH.     

Parameter sensitivity examination for a complete three-dimensional,two-phase,non-isothermal model of polymer electrolyte membrane fuel cell

Parameter sensitivity analysis is carried out for a complete three-dimensional, two-phase, non-isothermal model of polymer electrolyte membrane (PEM) fuel cell with a parallel flow field design. The model couples the two-phase flow of the multi-component reactants and liquid water, species transport, electrochemical reactions, proton and electron transport, and the electro-osmosis transport, back diffusion of water in the membrane, and energy transport. Twenty nine parameters, which are classified into the structural or transport parameters of porous layers (tortuosity, porosity, permeability, proton conductivity, electron conductivity, and thermal conductivity) as well as the electrochemical parameters (anodic and cathodic exchange current densities, anodic and cathodic transfer coefficients for anode and cathode reactions), are used to implement individual parameter investigation. The results show the parameters can be divided in to strongly sensitive, conditional sensitive and weak sensitive parameters according to its effect on the cell polarization curve. The optimization of parameters of cathode gas diffusion layer (GDL) and catalyst layer (CL) is more important to improve cell performance than that of anode GDL and CL because liquid water transport and removal affect significantly membrane hydration and reactant transport. Electrochemical parameters determine the activation potential and the slope of ohmic polarization hence these parameters can be used to fit experimental polarization curve more effectively than the other parameters.     

Treatment of two-phase flow in cathode gas channel for an improved one-dimensional proton exchange membrane fuel cell model

It has been reported recently that water flooding in the cathode gas channel has significant effects on the characteristics of a proton exchange membrane fuel cell. A better understanding of this phenomenon with the aid of an accurate model is necessary for improving the water management and performance of fuel cell. However, this phenomenon is often not considered in the previous one-dimensional models where zero or a constant liquid water saturation level is assumed at the interface between gas diffusion layer and gas channel. In view of this, a one-dimensional fuel cell model that includes the effects of two-phase flow in the gas channel is proposed. The liquid water saturation along the cathode gas channel is estimated by adopting Darcy’s law to describe the convective flow of liquid water under various inlet conditions, i.e. air pressure, relative humidity and air stoichiometry. The averaged capillary pressure of gas channel calculated from the liquid water saturation is used as the boundary value at the interface to couple the cathode gas channel model to the membrane electrode assembly model. Through the coupling of the two modeling domains, the water distribution inside the membrane electrode assembly is associated with the inlet conditions. The simulation results, which are verified against experimental data and simulation results from a published computational fluid dynamics model, indicate that the effects of relative humidity and stoichiometry of inlet air are crucial to the overall fuel cell performance. The proposed model gives a more accurate treatment of the water transport in the cathode region, which enables an improved water management through an understanding of the effects of inlet conditions on the fuel cell performance.     

Water management in alkaline anion exchange membrane fuel cell anode

Water management is an important issue for alkaline anion exchange membrane fuel cell (AAEMFC) due to its significant role in the energy conversion processes. In this study, a numerical model is developed to investigate the water transport in AAEMFC anode. The gas and liquid transport characteristics in the gas diffusion layer (GDL) and catalyst layer (CL) with different designs and under various operating conditions are discussed. The results show that the current density affects the liquid water distribution in anode most significantly, and the temperature is the second considerable factor. The stoichiometry ratio of the supplied reactant has insignificant effect on the liquid water transport in anode. The change of liquid water amount in anode with cathode relative humidity follows a similar trend with anode inlet relative humidity. Some numerical results are also explained with published experimental and modeling data with reasonable agreement.     

质子交换膜燃料电池内部传热传质三维模拟

针对常规流场质子交换膜燃料电池提出了三维非等温数学模型。模型考虑了电化学反应动力学以及反应气体在流道和多孔介质内的流动和传递过程,详细研究了水在质子膜内的电渗和扩散作用。计算结果表明,反应气体传质的限制和质子膜内的水含量直接决定了电极局部电流密度的分布和电池输出性能;在电流密度大于0.3~0.4A/cm2时开始出现水从阳极到阴极侧的净迁移;高电流密度时膜厚度方向存在很大的温度梯度,这对膜内传递过程有较大影响。     

Humidity of reactant fuel on the cell performance of PEM fuel cell with baffle-blocked flow field designs

The objective of this work is to examine the effects of humidity of reactant fuel at the inlet on the detailed gas transport and cell performance of the PEM fuel cell with baffle-blocked flow field designs. It is expected that, due to the water management problem, the effects of inlet humidity of reactant fuel gases on both anode and cathode sides on the cell performance are considerable. In addition, the effects of baffle numbers on the detailed transport phenomena of the PEM fuel cell with baffle-blocked flow field are examined. Due to the blockage effects in the presence of the baffles, more fuel gas in the flow channel can be forced into the gas diffuser layer (GDL) and catalyst layer (CL) to enhance the chemical reactions and then augment the performance of the PEMFC systems. Effect of liquid water formation on the reactant gas transport is taken into account in the numerical modeling. Predictions show that the local transport of the reactant gas, the local current density generation and the cell performance can be enhanced by the presence of the baffles. Physical interpretation for the difference in the inlet relative humidity (RH) effects at high and low operating voltages is presented. Results reveal that, at low voltage conditions, the liquid water effect is especially significant and should be considered in the modeling. The cell performance can be enhanced at a higher inlet relative humidity, by which the occurrence of the mass transport loss can be delayed with the limiting current density raised considerably.     

质子交换膜燃料电池建模及水热传输特性分析

针对质子交换膜燃料电池(PEMFC)水管理开展了研究,建立了一维非等温两相流解析模型,研究了不同电流密度、微孔层接触角和不同加湿方案对电池内部水分布和温度分布的影响,提出了更好的进气加湿方案。结果表明:电流密度增大会导致阳极拖干、阴极水淹加剧,导致电池各部分温度上升。因各层材料亲水性不同,在交界面处能观察到液态水阶跃现象。增大微孔层接触角促进阴极液态水反扩散到阳极,一定程度上缓解阳极变干,但过大的接触角可能导致阴极水淹加剧。通过采取"阳极充分加湿、阴极低加湿"的进气加湿方案可以有效提高电池性能,并且能在一定程度改善电池内部受热,提高电池使用寿命。     

Water distribution measurement for a PEMFC through neutron radiography

Neutron radiography has been used for in situ and non-destructive visualization and measurement technique for liquid water in a working proton exchange membrane fuel cell (PEMFC). In an attempt to differentiate water distribution in the anode side from that in the cathode side, a specially designed cell was machined and used for the experiment. The major difference between our design and traditional flow field design is the fact the anode channels and cathode channels were shifted by a channel width, so that the anode and cathode channels do not overlap in the majority of the active areas.

The neutron radiography experiments were performed at selected relative humidities, and stoichiometry values of cathode inlet. At each operating condition, the water distribution in anode/cathode gas diffusion layers (GDLs) was obtained. Image processing with four different spatial masks was applied to those images to differentiate liquid water in four different types of areas. Results indicate that the reactant gas relative humidity and stoichiometry significantly influence current density distribution and water distribution.     

Voltage instability in a simulated fuel cell stack correlated to cathode water accumulation

Single fuel cells running independently are often used for fundamental studies of water transport. It is also necessary to assess the dynamic behavior of fuel cell stacks comprised of multiple cells arranged in series, thus providing many paths for flow of reactant hydrogen on the anode and air (or pure oxygen) on the cathode. In the current work, the flow behavior of a fuel cell stack is simulated by using a single-cell test fixture coupled with a bypass flow loop for the cathode flow. This bypass simulates the presence of additional cells in a stack and provides an alternate path for airflow, thus avoiding forced convective purging of cathode flow channels. Liquid water accumulation in the cathode is shown to occur in two modes; initially nearly all the product water is retained in the gas diffusion layer until a critical saturation fraction is reached and then water accumulation in the flow channels begins. Flow redistribution and fuel cell performance loss result from channel slug formation. The application of in-situ neutron radiography affords a transient correlation of performance loss to liquid water accumulation. The current results identify a mechanism whereby depleted cathode flow on a single cell leads to performance loss, which can ultimately cause an operating proton exchange membrane fuel cell stack to fail.     

Along‐channel flooding prediction of polymer electrolyte membrane fuel cells

Non‐uniform current distribution in polymer electrolyte membrane (PEM) fuel cells results in local over‐heating, accelerated ageing, and lower power output than expected. This issue is quite critical when a fuel cell experiences water flooding. In this study, the performance of a PEM fuel cell is investigated under cathode flooding conditions. A two‐dimensional approach is proposed for a single PEM fuel cell based on conservation laws and electrochemical equations to provide useful insight into water transport mechanisms and their effect on the cell performance. The model results show that inlet stoichiometry and humidification, and cell operating pressure are important factors affecting cell performance and two‐phase transport characteristics. Numerical simulations have revealed that the liquid saturation in the cathode gas distribution layer (GDL) could be as high as 20%. The presence of liquid water in the GDL decreases oxygen transport and surface coverage of active catalyst, which in turn degrades the cell performance. The thermodynamic quality in the cathode flow channel is found to be greater than 99.7%, indicating that liquid water in the cathode gas channel exists in very small amounts and does not interfere with the gas phase transport. A detailed analysis of the operating conditions shows that cell performance should be optimized based on the maximum average current density achieved and the magnitude of its dispersion from its mean value. Copyright © 2010 John Wiley & Sons, Ltd.     

Analysis of liquid water transport in cathode catalyst layer of PEM fuel cells

The performance of a polymer electrolyte membrane (PEM) fuel cell is significantly affected by liquid water generated at the cathode catalyst layer (CCL) potentially causing water flooding of cathode; while the ionic conductivity of PEM is directly proportional to its water content. Therefore, it is essential to maintain a delicate water balance, which requires a good understanding of the liquid water transport in the PEM fuel cells. In this study, a one-dimensional analytical solution of liquid water transport across the CCL is derived from the fundamental transport equations to investigate the water transport in the CCL of a PEM fuel cell. The effect of CCL wettability on liquid water transport and the effect of excessive liquid water, which is also known as “flooding”, on reactant transport and cell performance have also been investigated. It has been observed that the wetting characteristic of a CCL plays significant role on the liquid water transport and cell performance. Further, the liquid water saturation in a hydrophilic CCL can be significantly reduced by increasing the surface wettability or lowering the contact angle. Based on a dimensionless time constant analysis, it has been shown that the liquid water production from the phase change process is negligible compared to the production from the electrochemical process.     

Anode water removal and cathode gas diffusion layer flooding in a proton exchange membrane fuel cell

Anode water removal (AWR) is studied as a diagnostic tool to assess cathode gas diffusion layer (GDL) flooding in PEM fuel cells. This method uses a dry hydrogen stream to remove product water from the cathode, showing ideal fuel cell performance in the absence of GDL mass transfer limitations related to water. When cathode GDL flooding is limiting, the cell voltage increases as the hydrogen stoichiometry is increased. Several cathode GDLs were studied to determine the effect of microporous layer (MPL) and PTFE coating. The largest voltage gains occur with the use of cathode GDLs without an MPL since these GDLs are prone to higher liquid water saturation. Multiple GDLs are studied on the cathode side to exacerbate GDL flooding conditions to further confirm the mechanism of the AWR process. Increased temperature and lower cathode RH allow for greater overall water removal so the voltage improvement occurs faster, though this leads to quicker membrane dehydration.     

Numerical study of cell performance and local transport phenomena in PEM fuel cells with various flow channel area ratios

Three-dimensional models of proton exchange membrane fuel cells (PEMFCs) with parallel and interdigitated flow channel designs were developed including the effects of liquid water formation on the reactant gas transport. The models were used to investigate the effects of the flow channel area ratio and the cathode flow rate on the cell performance and local transport characteristics. The results reveal that at high operating voltages, the cell performance is independent of the flow channel designs and operating parameters, while at low operating voltages, both significantly affect cell performance. For the parallel flow channel design, as the flow channel area ratio increases the cell performance improves because fuel is transported into the diffusion layer and the catalyst layer mainly by diffusion. A larger flow channel area ratio increases the contact area between the fuel and the diffusion layer, which allows more fuel to directly diffuse into the porous layers to participate in the electrochemical reaction which enhances the reaction rates. For the interdigitated flow channel design, the baffle forces more fuel to enter the cell and participate in the electrochemical reaction, so the flow channel area ratio has less effect. Forced convection not only increases the fuel transport rates but also enhances the liquid water removal, thus interdigitated flow channel design has higher performance than the parallel flow channel design. The optimal performance for the interdigitated flow channel design occurs for a flow channel area ratio of 0.4. The cell performance also improves as the cathode flow rate increases. The effects of the flow channel area ratio and the cathode flow rate on cell performance are analyzed based on the local current densities, oxygen flow rates and liquid water concentrations inside the cell.     

Three-dimensional multiphase modeling of alkaline anion exchange membrane fuel cell

Alkaline anion exchange membrane (AAEM) fuel cell is becoming more attractive because of its outstanding merits, such as fast electrochemical kinetics and low dependence on non-precious catalyst. In this study, a three-dimensional multiphase non-isothermal AAEM fuel cell model is developed. The modeling results show that the performance is improved with more anode humidification, but the improvement becomes less significant at higher humidification levels. The humidification level of anode can change the water removal mechanisms: at partial humidification, water is removed as vapor; and for full humidification, water is removed as liquid. Cathode humidification is even more critical than anode. Liquid water supply in cathode has a positive effect on performance, especially at high current densities. With more liquid water supply in cathode, liquid water starts moving from channel to CL, rather than being removed from CL. Liquid water supply in cathode is needed to balance the water amounts in anode and cathode. Decreasing the membrane thickness generally improves the cell performance, and the improvement is even enhanced with thinner membranes, due to the faster water diffusion between anode and cathode, which reduces the mass transport losses.     

Novel in situ measurements of relative humidity in a polymer electrolyte membrane fuel cell

Miniature temperature/humidity sensors are incorporated into the graphite flowplates of a single cell polymer electrolyte membrane fuel cell (PEMFC) in order to measure the humidity profile along the serpentine channels of both anode and cathode in real time. The sensors show robust performance and importantly are able to recover after saturation. The key observation is a significant increase in relative humidity along the anode gas channel due to back diffusion of water from cathode to anode. Such measurements may be used to determine the water balance in the cell under a range of operating conditions to facilitate model validation and system optimisation.     

Assisted water management in a PEMFC with a modified flow field and its effect on performance

This work designed and tested innovative flow channels in order to improve water management in a polymer electrolyte membrane fuel cell (PEMFC). The design employed slanted channels with an angle of 20° in a flow plate to collect the liquid water that permeated from the gas diffusion layers. The effects of orientations of the slanted channels in up-slanted and down-slanted directions and relative humidity levels on the cell performance were investigated. The experimental results showed that modifying the anode flow field using down-slanted channels provided higher cell performance. Water concentration at the gas diffusion layer is reduced resulting in more back diffusion of water from the cathode to anode, thus inducing membrane hydration and improving the conductivity. Promotion of water removal by applying down-slanted channels in the cathode side did not improve the performance. This work has demonstrated that channel cross-section design alone could improve the PEM fuel cell performance. The anode down-slanted cell indeed improved the performances at extremely wet condition and the power was equally good as that without modified flow channel at less wet condition.     

Three-dimensional two-phase flow model of proton exchange membrane fuel cell with parallel gas distributors

A non-isothermal, steady-state, three-dimensional (3D), two-phase, multicomponent transport model is developed for proton exchange membrane (PEM) fuel cell with parallel gas distributors. A key feature of this work is that a detailed membrane model is developed for the liquid water transport with a two-mode water transfer condition, accounting for the non-equilibrium humidification of membrane with the replacement of an equilibrium assumption. Another key feature is that water transport processes inside electrodes are coupled and the balance of water flux is insured between anode and cathode during the modeling. The model is validated by the comparison of predicted cell polarization curve with experimental data. The simulation is performed for water vapor concentration field of reactant gases, water content distribution in the membrane, liquid water velocity field and liquid water saturation distribution inside the cathode. The net water flux and net water transport coefficient values are obtained at different current densities in this work, which are seldom discussed in other modeling works. The temperature distribution inside the cell is also simulated by this model.     

An approach for determining the liquid water distribution in a liquid-feed direct methanol fuel cell

In determining the liquid water distribution in the anode (or the cathode) diffusion medium of a liquid-feed direct methanol fuel cell (DMFC) with a conventional two-phase mass transport model, a current-independent liquid saturation boundary condition at the interface between the anode flow channel and diffusion layer (DL) (or at the interface between the cathode flow channel and cathode DL) needs to be assumed. The numerical results resulting from such a boundary condition cannot realistically reveal the liquid distribution in the porous region, as the liquid saturation at the interface between the flow channel and DL varies with current density. In this work, we propose a simple theoretical approach that is combined with the in situ measured water-crossover flux in the DMFC to determine the liquid saturation in the anode catalyst layer (CL) and in the cathode CL. The determined liquid saturation in the anode CL (or in the cathode CL) can then be used as a known boundary condition to determine the water distribution in the anode DL (or in the cathode DL) with a two-phase mass transport model. The numerical results show that the water distribution becomes much more realistic than those predicted with the assumed boundary condition at the interface between the flow channel and DL.     

Numerical analysis of gas cross-over through the membrane in a proton exchange membrane fuel cell

Mass transport phenomena through the membrane have the major role in performance of a proton exchange membrane (PEM) fuel cell. Water is transported through the membrane due to diffusion, convection and electro-osmotic drag. Normally it is assumed that the membrane is impermeable against gases. Strictly speaking there are some amount of solute gases in liquid water which move within the membrane and reach to the other side. For example, oxygen dissolves into the water at cathode catalyst. Most of this oxygen reacts with proton and produces electricity. But some oxygen molecules diffuse toward anode side and react directly with hydrogen at anode catalyst. This process leads to waste of energy since direct reaction releases energy in form of heat. In this paper these processes have been studied. We have developed a two-dimensional numerical model using full Navier-Stokes equations and species transport equations of hydrogen, oxygen and water. It was found that cross-over of reactant gases has a considerable effect on cell energy efficiency in some common cases.     

Characteristics of water transport through the membrane in direct methanol fuel cells operating with neat methanol

The water required for the methanol oxidation reaction in a direct methanol fuel cell (DMFC) operating with neat methanol can be supplied by diffusion from the cathode to the anode through the membrane. In this work, we present a method that allows the water transport rate through the membrane to be in-situ determined. With this method, the effects of the design parameters of the membrane electrode assembly (MEA) and operating conditions on the water transport through the membrane are investigated. The experimental data show that the water flux by diffusion from the cathode to the anode is higher than the opposite flow flux of water due to electro-osmotic drag (EOD) at a given current density, resulting in a net water transport from the cathode to the anode. The results also show that thinning the anode gas diffusion layer (GDL) and the membrane as well as thickening the cathode GDL can enhance the water transport flux from the cathode to the anode. However, a too thin anode GDL or a too thick cathode GDL will lower the cell performance due to the increases in the water concentration loss at the anode catalyst layer (CL) and the oxygen concentration loss at the cathode CL, respectively.