新型氨氮复合分离流程及装备

开发了全填料结构的吸收，精馏、压缩冷凝新型复合分离流程及装备，用于精细化工氨氮废气（水）的处理，在获得高收率，高纯度的液氨产品同时，基本实现了气、液无污染排放。     

0.7～1.9MPa下Mellapak 350Y填料传质性能的测定

引　言最近十几年以来 ,规整填料已广泛应用于新建的蒸馏塔以及老塔的改造中 .在常、减压操作中 ,与板式塔相比 ,在相同的分离效率下填料塔具有压降更低和处理能力更大的优点 .但在高压蒸馏操作中 ,液体的喷淋密度非常大 ,其范围在 2 0～ 10 0ｍ3·ｍ- 2 ·ｈ- 1,单位塔截面积上液体负荷的增加使得填料对液体的自分布能力减弱 ,液体易产生偏流、沟流等不均匀流动 .随着压力增大 ,充了气的液相、高的汽液相密度比值、高的汽液相黏度比值等因素都会使填料床层的持液量加大 ,空隙率降低 ,其结果使规整填料处理能力受到制约 .在高压条件下 ,规整…     

规整填料精馏塔的设计计算

通过大量的文献调研，比较了规整填料精馏塔和板式塔的优缺点，对规整填料精馏塔内压降、传质及液泛时压降的计算公式进行了比较，总结出设计计算规整填料精馏塔的步骤与方法，为规整填料精馏塔的应用提供了基础。     

薄膜蒸发器的分离效率

The recovery of contaminants and useful substances from liquid wastes, the purification of production effluents and the separation of thermally instable mixtures are some of the multivarious applications of thin-film distillors in many processes of the chemical and allied industries and of the food industries. In a study carried out in pilot plants with distillation test systems there was found a good agreement between the experimental separation results and those obtained by computing with a theorectical model; the latter is based on the assumption of phase equilibrium between the vapour formed on an infinitely small element of area in a liquid film of any given concentric periphery of the vertically arranged evaporator. These tests were perfomed under various phase loads.     

Investigation of flow parameters and efficiency of mixture separation on a structured packing

Results of experimental study of the effect of initial maldistribution of structured packing irrigation on efficiency of binary mixture separation are presented in this article. The studies were carried out in the experimental distillation column with the diameter of 0.9 m using the R114 and R21 freon mixture. Experiments were performed on the structured Mellapak 350.Y packing of stainless steel 316L, containing 19 layers with the total height of 4.016 m at the ratio of mole liquid and vapor flow rates L/V = 1 and 1.7, respectively, and the pressure in the upper part of the column p_top = 3 bars. Nonuniformity at the packing inlet was generated via the blocking of some holes in the liquid distributor. Here, we present some results on efficiency of mixture separation, pressure drop on the packing, distribution of local liquid flow rate under the packing over the cross‐section and on the column wall within the range of vapor loading factor (0.69 < F_v < 1.61 Pa^0.5), as well as experimental data on distribution of local concentration of the low‐boiling component over the cross‐section and along the height of the structured packing. It is found out that significant maldistribution of mixture concentration and liquid flow rate over the cross‐section slightly changes along the height in the lower part of the column at a change in the degree of packing irrigation nonuniformity at the inlet. It is shown that efficiency of mixture separation depends considerably on the value of parameter L/V, vapor flow factor F_v, and size of the zone underirrigated by liquid at the inlet. In the studied range of liquid and vapor flow rates, the relative pressure drop on the packing does not depend on the ratio of liquid and vapor flow rates L/V and degree of irrigation maldistribution. © 2013 American Institute of Chemical Engineers AIChE J 60: 690–705, 2014     

高通量催化精馏规整填料的流体力学性能

介绍了一种可应用于催化精馏工艺的高通量催化精馏规整填料(HCCP),并对其流体力学性能进行了研究与讨论。以空气-水物系为介质在内径为400 mm的冷模精馏塔内进行实验,测量了该填料的干湿塔压降、持液量等流体力学性能。高通量催化精馏规整填料在结构方面进行了改进,使催化剂装填量可控,实验结果表明:填料在降低塔内压降、增加通量方面具有明显优势。最后对实验数据进行回归,获得经验关联式;实验测量值与公式计算结果吻合较好,这表明,数据回归获得的关联式可用于预测一定操作条件下填料的流体力学性能,用于工业实践及设备放大。     

高效规整填料塔技术在苯酐精制过程中的应用

介绍了国内苯酐精制新工艺和高效规整填料塔技术。实际应用结果表明新工艺比旧有技术和设备提高了产品质量和收率 ,处理能力也大幅提高 ,能耗明显下降。     

在高压下规整填料中的流动实验研究

Both distillation performance and hydrodynamic study for backmixing by tracer technique were carried out in a high-pressure packed column with 0.15 m inner diameter over a wide range of operating conditions. Isobutane and n-pentane are employed as test mixture in the distillation experiment and air/water is used for the hydrodynamic study. The column is installed with Mellapak 350Y structured packing and the total packing height is 2.0 m. With the increasing operating pressure, the separation efficiency increases slightly while the F-factor corresponding to the maximum efficiency at each pressure is descending. It is noted that, at all operating pressures, with the increase of F-factor, the packing efficiency is slightly higher up to the flooding point. The application of SRP model to high-pressure distillation gives much lower values of HTUOG than those obtained experimentally. An additional term, the height of mixing unit, is introduced to correct the SRP model and improve its accuracy at high pressure. From the tracer experiments, the height of mixing unit for gas phase was found to be larger than that for the liquid phase. From this viewpoint, it is believed that the gas phase backmixing gives more unfavorable influence on the separation efficiency in comparison with liquid phase.     

高通量催化精馏填料的停留时间分布研究

介绍了高通量催化精馏规整填料(HCCP),是一种模块化催化精馏规整填料。停留时间分布(RTD)是催化精馏填料的重要性能参数,同时影响着填料的分离效果和塔内化学反应的进行,着重研究了高通量催化精馏填料的RTD问题。实验在内径为400 mm的冷模塔内进行,常温常压下以空气-水为介质,氯化钠水溶液作为示踪剂,通过脉冲注入的扰动-响应技术获得RTD曲线。采用轴向扩散模型分析RTD曲线,可得出模型参数彼克列数PeL及填料的持液量、轴向扩散因子Dax。结果表明,该填料内的返混现象较轻微。分析计算的结果即可用于填料性能的评价,为填料的进一步改进提供理论基础;也可用于催化精馏塔的设计和优化。     

规整填料塔多元蒸馏过程混合型模型的模拟

填料塔精馏过程的模拟设计大多采用平衡级模型,但由于单一板效率值的难以确定,很多场合模拟很不成功;而新提出的非平衡级模型认为塔内传质传热均处于非平衡状态,由于方程数和经验性参数多,模型求解非常困难。文章针对规整填料的特点,建立了规整填料塔蒸馏过程的一种混合型模型,模型的主要特征是认为气液二相传质处于不平衡状态,而传热处于平衡状态。模型建立在实际填料基础上,既舍去传统的平衡级模型不确定性,又省略了非平衡级模型中复杂的经验性传热系数和液相传质系数的计算。模型计算值和实验值符合较好,也证实混合型模型既反映实际,又使模型求解变得相对容易。     

规整填料在双氧水生产分离过程中的应用

介绍规整填料用于过氧化氢生产中的油 水分离过程。用于萃取塔、干燥塔和碱分离器的改造 ,使分离效率和能力得到改进。     

泡沫碳化硅波纹规整填料内的液体流动特性

通过采用配备微距镜头的高速摄像仪记录单波纹片上的液体流动行为,发现了泡沫碳化硅波纹规整填料内同时存在液膜流动和准壁流两种液体流动模式。同时测定了组合波纹片之间的液体传递量,并将泡沫碳化硅波纹规整填料与金属丝网波纹填料和金属板波纹规整填料的测试结果进行比较,结果表明泡沫碳化硅波纹规整填料的单波纹片上的液体扩散程度较大,组合波纹片之间的液体传递量高于金属丝网波纹填料和金属板波纹规整填料。研究结果揭示了泡沫碳化硅波纹规整填料具有高效传质特性的根本原因在于其独特的三维空间网孔结构增强了液体在单波纹片上的横向扩散能力和在组合波纹片之间的径向传递能力,为新型高效规整填料的机理研究和进一步开发开拓了思路。     

溢流管直径对旋流器分离效率影响的数值模拟

在溢流管长度L0均分别设定为10mm、15mm、20mm条件下,应用Fluent软件对不同直径的直筒式水力旋流器进行了数值模拟,得到了不同入口速度下的压降和分离效率。结果表明,当溢流管直径为3mm时,旋流器的分离效率最大。旋流器主直径D一定时,使旋流器分离效率最高的直径也是一定的,一般溢流口直径选择经验值为D/(5~8.5)。     

Experimental validation of a flexible modeling approach for distillation columns with packings

The two main concepts for the modeling of distillation columns are the equilibrium‐stage (EQ) and the nonequilibrium‐stage (NEQ). A model is presented which combines decisive features of both conventional concepts. Based on the idea of a reduced nonequilibrium‐stage (RNEQ), this model can be used for the simulation of distillation columns with packings. In contrast to the conventional NEQ approach, this model neglects the influence of liquid side mass‐transfer coefficients, which ultimately allows to come up with only one empirical equation describing the overall mass transfer. Thus, a considerable reduction in model complexity is reached, which allows for an efficient consideration of new experimental distillation results. Fitted to experimental data, the model is able to predict, how different pressures and chemical systems might affect the separation efficiency. By comparing calculation results with experimentally determined separation efficiencies for three different packing types, these valuable RNEQ qualities are illustrated. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3833–3847, 2014     

Development of enhanced three-dimensional printed packings for scale-up of distillation columns: A successful case study

This publication presents a general approach for the enhancement of packings regarding scalability, separation efficiency, and fluid dynamic properties using three-dimensional (3D) printing. The methodology is used to develop miniaturized, scalable packings for process development, and scale-up applications. For this purpose, a 3D printable computer-aided design version of the Rombopak 9M industrial packing (RP9M-3D), which is known for its positive scalability properties, was created. An initial characterization by means of computational fluid dynamics simulations and mass transfer measurements reveals positive but also negative design properties. These findings are used to create a more advanced, miniaturized packing structure, the XW-Pak. The evolved structure is compared to the RP9M-3D. The simulation and experimental results show that the enhanced packing, which is still in the early stages of development, exhibits higher separation efficiencies with improved scalability properties at the same void fraction and surface area than the RP9M-3D.     

液相流动方式对波纹规整填料性能的影响

根据液相在波纹规整填料片上呈现渗流、膜状流等不同的流动方式,选择5种不同的波纹规整填料对其流体力学和传质性能进行研究,以探究液相在波纹片上的流动方式对波纹规整填料性能的影响.研究结果表明,液相呈渗流流动的泡沫碳化硅波纹规整填料(SCFP型)有利于液体横向扩散和液膜均匀分布,当液相喷淋密度和气相F因子均较小时,其压降最低,传质效率最高;液相主要呈渗流流动、兼有膜状流动的双层错孔丝网填料(DMⅢ型)有利于波纹片两侧液体交换,强化液体在流动过程中的扰动,其压降及传质性能略逊于SCFP型填料;液相主要呈膜状流动的BX型、DMⅠ型及DMⅡ型填料波纹片表面液膜较厚,横向扩散能力差,其传质效率低于SCFP型和DMⅢ型填料.研究揭示了依靠渗流作用的波纹规整填料具有较好的应用性能,为波纹规整填料的进一步发展开拓了新思路.