A novel slurry sampling analysis of lead in different water samples by electrothermal atomic absorption spectrometry after coprecipitated with cobalt/pyrrolidine dithiocarbamate complex

A preconcentration/separation technique based on the coprecipitation of lead with cobalt/pyrrolidine dithiocarbamate complex (Co(PDC)(2)) and subsequently its direct slurry sampling determination by electrothermal atomic absorption spectrometry (AAS) was described. For this purpose, at first, lead was coprecipitated with cobalt/pyrrolidine dithiocarbamate complex formed using ammonium pyrrolidine dithiocarbamate (APDC) as a chelating agent and cobalt as a carrier element. The supernatant was then separated and the slurry of the precipitate prepared in Triton X-100 was directly analyzed by electrothermal atomic absorption spectrometry with respect to lead concentration. The effects of experimental conditions on coprecipitation of lead with gathering precipitate as well as homogeneity and stability of the slurry were investigated. After the optimization of experimental parameters, a 100-fold enrichment of the analyte with quantitative recovery (>90%) and high precision (<10% R.S.D.) were obtained. By using the proposed technique, the lead concentrations in heavy matrices of Certified Sea-water and wastewater samples could be practically and rapidly determined in the range of 95% confidence level. The detection limit of the described method for lead using sample-matching blanks was 1.5ng/L (3sigma, N=10).     

Cloud point extraction for the determination of copper, nickel and cobalt ions in environmental samples by flame atomic absorption spectrometry

A cloud point extraction procedure was presented for the preconcentration of copper, nickel and cobalt ions in various samples. After complexation with methyl-2-pyridylketone oxime (MPKO) in basic medium, analyte ions are quantitatively extracted to the phase rich in Triton X-114 following centrifugation. 1.0 mol L⁻¹ HNO₃ nitric acid in methanol was added to the surfactant-rich phase prior to its analysis by flame atomic absorption spectrometry (FAAS). The adopted concentrations for MPKO, Triton X-114 and HNO₃, bath temperature, centrifuge rate and time were optimized. Detection limits (3 SDb/m) of 1.6, 2.1 and 1.9 ng mL⁻¹ for Cu²⁺, Co²⁺ and Ni²⁺ along with preconcentration factors of 30 and for these ions and enrichment factor of 65, 58 and 67 for Cu²⁺, Ni²⁺ and Co²⁺, respectively. The high efficiency of cloud point extraction to carry out the determination of analytes in complex matrices was demonstrated. The proposed procedure was applied to the analysis of biological, natural and wastewater, soil and blood samples.     

On-line separation and preconcentration of lead(II) by solid-phase extraction using activated carbon loaded with xylenol orange and its determination by flame atomic absorption spectrometry

Activated carbon loaded with xylenol orange in a mini-column was used for the highly selective separation and preconcentration of Pb(II) ions. An on-line system for enrichment and the determination of Pb(II) was carried out on flame atomic absorption spectrometry. The conditions of preconcentration and quantitative recovery of Pb(II) from diluted solution, such as pH of aqueous phase, amount of the sorbent, volume of the solutions and flow variables were studied as well as effect of potential interfering ions. Under the optimum conditions, Pb(II) in an aqueous sample was concentrated about 200-fold and the detection limit was 0.4 ng mL⁻¹ Pb(II). The adsorption capacity of the solid phase was 0.20 mg of lead per one gram of the modified activated carbon. The modified activated carbon is stable for several treatments of sample solutions without the need for using any chemical reagent. The recovery of lead(II) from river water, waste water, tap water, and in the following reference materials: SRM 2711 Montana soil and GBW-07605 tea were obtained in the range of 97–104% by the proposed method.     

Sorbent extraction of rubeanic acid-metal chelates on a new adsorbent: Sepabeads SP70

A sorbent extraction procedure for lead, iron, cadmium and manganese ions on Sepabeads SP70 adsorption resin has been presented prior to their flame atomic absorption spectrometric determinations. By the passage of aqueous samples including analyte ions-rubeanic acid chelates through Sepabeads SP70 column, metal chelates adsorb quantitatively and almost all matrix elements will pass through the column to drain. The influence of potential interfering ions was also studied. The validation of the method was made though the analysis of LGC 6010 Hard drinking water, SRM 1577b Bovine liver and GBW 07603 Bush branches and leaves standard reference materials (SRM). The method was applied to the determination of analyte ions from various water, wastewater, cow meat and milk, red wine, and tobacco samples with successfully results.     

Slurry analysis of cadmium and copper collected on 11-mercaptoundecanoic acid modified TiO2 core-Au shell nanoparticles by flame atomic absorption spectrometry

Separation/preconcentration of copper and cadmium using TiO(2) core-Au shell nanoparticles modified with 11-mercaptoundecanoic acid and their slurry analysis by flame atomic absorption spectrometry were described. For this purpose, at first, titanium dioxide nanoparticles were coated with gold shell by reducing the chloroauric acid with sodium borohydride and then modified with 11-mercaptoundecanoic acid. The characterization of modified nanoparticles was performed using ultra-violet spectroscopy and dynamic light scattering. Copper and cadmium were then collected on the prepared sorbent by batch method. The solid phase loaded with the analytes was separated by centrifugation and the supernatant was removed. Finally, the precipitate was slurried and directly aspirated into the flame for the determination of analytes. Thus, elution step and its all drawbacks were eliminated. The effects of pH, amount of sorbent, slurry volume, sample volume and diverse ions on the recovery were investigated. After optimization of experimental parameters, the analytes in different certified reference materials and spiked water samples were quantitatively recovered with 5% RSD. The analytes were enriched up to 20-fold. Limits of detection (N=10, 3σ) for copper and cadmium were 0.28 and 0.15 ng mL(-1), respectively.     

Gadolinium hydroxide coprecipitation system for the separation-preconcentration of some heavy metals

A simple and new procedure for the determination of trace amounts of lead(II), cobalt(II), manganese(II) and copper(II) is described, that combines atomic absorption spectrometry-gadolinium hydroxide coprecipitation. One milliliter of 1% gadolinium(III) solution was added to each sample; the pH was then adjusted to 11 in order to collect trace heavy metals on gadolinium(III) hydroxide. The precipitate was separated by centrifugation and dissolved in 1 mL of 1 mol L(-1) HNO3. The influences of analytical parameters including amount of gadolinium(III), sample volume, etc. were investigated on the recoveries of analyte ions. The effects of concomitant ions were also examined. The recoveries of the analyte ions were greater than 95. The detection limits for the analyte elements based on 3 sigma (n=20) were in the range of 0.52-12.0 microg L(-1). The method was applied to the determination of analytes in real samples and good results were obtained (relative standard deviations <10%, recoveries >95%).     

Study on solid phase extraction and graphite furnace atomic absorption spectrometry for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent

A solid phase extraction and graphite furnace atomic absorption spectrometry (GFAAS) for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent was studied. Trace amounts of chromium, nickel, silver, cobalt, copper, cadmium and lead were reacted with 2-(2-quinolinil-azo)-4-methyl-1,3-dihydroxidobenzene (QAMDHB) followed by adsorption onto MCI GEL CHP 20Y solid phase extraction column, and 1.0molL(-1) HNO(3) was used as eluent. The metal ions in 300mL solution can be concentrated to 1.0mL, representing an enrichment factor of 300 was achieved. The recoveries of analytes at pH 8.0 with 1.0g of resin were greater than 95% without interference from alkaline, earth alkaline and some metal ions. When detected with graphite furnace atomic absorption spectrometry, the detection limits in the original samples were 1.4ngL(-1) for Cr(III), 1.0ngL(-1) for Ni(II), 0.85ngL(-1) for Ag(I), 1.2ngL(-1) for Co(II), 1.0ngL(-1) for Cu(II), 1.2ngL(-1) for Cd(II) and 1.3ngL(-1) for Pb(II). The validation of the procedure was performed by the analysis of the certified standard reference materials, and the presented procedure was applied to the determination of analytes in biological, water and soil samples with good results (recoveries range from 89 to 104%, and R.S.D.% lower than 3.2%. The results agreed with the standard value or reference method).     

Determination of trace metals by atomic absorption spectrometry after coprecipitation with europium hydroxide

A procedure for the determination of trace amounts of chromium(III), iron(III), lead(II) and manganese(II) is described, that combines atomic absorption spectrometry-europium hydroxide coprecipitation. The influences of analytical parameters including amount of europium(III), amount of ammonia, sample volume, etc. were investigated on the recoveries of analyte ions. The effects of concomitant ions were also examined. The recoveries of the analyte ions were in the range of 95-104%. The detection limits (3 s) were in the range of 1.7-17.1 microg/L. The validation of the presented coprecipitation procedure was performed by the analysis of Bovine Liver 1577-b and BCR-144R Sewage Sludge (domestic origin) standard reference materials. The method was applied to the determination of analytes in real samples including natural waters and some food, soil and fertilizer samples, etc. and good results were obtained (relative standard deviations < 10%, recoveries > 95%).     

Speciation determination of chromium(III) and (VI) using preconcentration cloud point extraction with flame atomic absorption spectrometry (FAAS)

bis-[2-Hydroxy-1-naphthaldehyde] thiourea was synthesized and preconcentration cloud point extraction (CPE) for speciation determination of chromium(III) and (VI) in various environmental samples with flame atomic absorption spectrometry (FAAS) has been developed. Chromium(III) complexes with bis-[2-hydroxynaphthaldehyde] thiourea is subsequently entrapped in the surfactant micelles. After complexation of chromium(III) with reagent, the analyte was quantitatively extracted to the surfactant-rich phase in the non-ionic surfactant Triton X-100 after centrifugation. The effect of pH, concentration of chelating agent, surfactant, equilibration temperature and time on CPE was studied. The relative standard deviation was 2.13% and the limits of detection were around 0.18 μg L⁻¹.     

On-line preconcentration and determination of mercury in biological and environmental samples by cold vapor-atomic absorption spectrometry

An on-line procedure for the determination of traces of total mercury in environmental and biological samples is described. The present methodology combines cold vapor generation associated to atomic absorption spectrometry (CV-AAS) with preconcentration of the analyte on a minicolumn packed with activated carbon. The retained analyte was quantitatively eluted from the minicolumn with nitric acid. After that, volatile specie of mercury was generated by merging the acidified sample and sodium tetrahydroborate(III) in a continuous flow system. The gaseous analyte was subsequently introduced via a stream of Ar carrier into the atomizer device. Optimizations of both, preconcentration and mercury volatile specie generation variables were carried out using two level full factorial design (2(3)) with 3 replicates of the central point. Considering a sample consumption of 25mL, an enrichment factor of 13-fold was obtained. The detection limit (3sigma) was 10ngL(-1) and the precision (relative standard deviation) was 3.1% (n=10) at the 5microgL(-1) level. The calibration curve using the preconcentration system for mercury was linear with a correlation coefficient of 0.9995 at levels near the detection limit up to at least 1000microgL(-1). Satisfactory results were obtained for the analysis of mercury in tap water and hair samples.     

Hollow fiber-protected liquid-phase microextraction of triazine herbicides

A new microextraction technique termed hollow fiber-protected liquid-phase microextraction (LPME) was developed. Triazines were employed as model compounds to assess the extraction procedure and were determined by gas chromatography/mass spectrometry. Toluene functioned as both the extraction solvent and the impregnation solvent. Some important extraction parameters, such as effect of salt, agitation, pH, and exposure time were optimized. The new method provided good average enrichment factors of > 150 for eight analytes, good repeatability (RSDs <3.50%, n = 7), and good linearity (r2 > or = 0.9995) for spiked deionized water samples. The limits of detection (LODs) were in the range of 0.007-0.063 microg/L (S/N = 3) under selected ion monitoring mode. In addition to enrichment, hollow fiber-protected LPME also served as a technique for sample cleanup because of the selectivity of the membrane, which prevented large molecules and extraneous materials, such as humic acids in solution, from being extracted. The utilization of this procedure in the extraction of a slurry sample (mixture of soil and water) also gave good precision (RSDs <5.00%, n = 3) and LODs (0.04-0.18 microg/L, S/N = 3). Finally, the comparison of the new method with the static solvent drop LPME and solid-phase microextraction was performed. The results demonstrated that hollow fiber-protected LPME was a fast, accurate, and stable sample pretreatment method that gave very good enrichment factors for the extraction of triazine herbicides from aqueous or slurry samples.     

Electrochemical deposition and oxidation of CuFe2 alloy: a new method to deposit CuFe2O4 thin films at room temperature

The objective of this research work is to develop an electrochemical process to deposit polycrystalline copper iron oxide (CuFe₂O₄) films on different conducting substrates at room temperature (27°C). Cathodic Electrodeposition of CuFe₂ was carried out on various conducting substrates in galvanostatic mode. The composition of alloy was determined using atomic absorption spectroscopy (AAS) technique. The electrodeposited CuFe₂ alloy films were electrochemically oxidized (anodized) in aqueous KOH electrolyte at room temperature. The structural studies of oxide films were carried out using X-ray diffraction and IR absorption techniques. For surface morphological studies, optical microscopy and scanning electron microscopy (SEM) techniques were used.     

Dysprosium(III) hydroxide coprecipitation system for the separation and preconcentration of heavy metal contents of table salts and natural waters

A procedure for the determination of trace amounts of Pb(II), Cu(II), Ni(II), Co(II), Cd(II) and Mn(II) is described, that combines atomic absorption spectrometry-dysprosium hydroxide coprecipitation. The influences of analytical parameters including amount of dysprosium(III), centrifugation time, sample volume, etc. were investigated on the recoveries of analyte ions. The effects of concomitant ions were also examined. The recoveries of the analyte ions were in the range of 95.00-104.00%. The detection limits corresponding to three times the standard deviation of the blank for the analytes were in the range of 14.1-25.3 microg/L. The method was applied to the determination of lead, copper, nickel, cobalt, cadmium and manganese ions in natural waters and table salts good results were obtained (relative standard deviations <10%, recoveries >95%).     

Quantum chemical modelling of point defects in KNbO3 perovskite crystals

We present results of semi-empirical quantum chemical calculations for several perovskite KNb_xTa_1−xO₃ (KTN) solid solutions, as well as point intrinsic defects – F centers and hole polarons bound to K vacancy – in KNbO₃. Method of the intermediate neglect of the differential overlap (INDO) was combined with typically 320-atom supercells and atomic geometry optimization. Analysis of the optimized atomic and electronic structure has clearly demonstrated that several nearest Nb atoms substituting for Ta in KTaO₃ – unlike Ta impurities in KNbO₃ – reveal the self-ordering effect, which probably triggers the ferroelectricity observed in KTN. We predict co-existence of one-site (atomic) and two-site (molecular) polarons with close absorption energies (≈1 eV). When available, the INDO results are compared with ab initio calculations. The relevant experimental data are discussed.     

一种新型含Al低Cr合金钢在模拟油田采出液环境下的CO2腐蚀行为

以自行设计开发的新型3Cr2Al低合金钢为研究对象,采用高温高压磁力驱动反应釜进行饱和CO₂模拟油田采出液环境下的腐蚀模拟实验,通过失重法获取腐蚀速率评价其耐蚀性能,并结合扫描电子显微镜、能谱分析、电化学测试等表征手段,研究腐蚀产物膜结构及成分特征,探讨耐蚀机理。相比3Cr钢,3Cr2Al钢中少量Al的添加提高了材料的抗CO₂腐蚀性能,在短周期(20 h)和长周期(144 h)条件下,其腐蚀速率分别下降15%和69%,这种耐蚀性能的提升主要是由于3Cr2Al钢表面产物膜中不仅有Cr的富集,同时还有Al的富集,提高了产物膜对基体的保护性。溶液中的氯离子对产物膜中Al的富集存在一定影响,在低氯溶液环境中,3Cr2Al钢表面腐蚀产物膜中Al/Fe原子比明显高于其Cr/Fe原子比,Al的富集更明显;当提高溶液氯离子浓度,腐蚀产物膜中Al/Fe原子比相比低氯溶液明显降低,Al的富集程度减弱,阳极极化曲线半钝化现象消失。     

Mid-infrared chemical sensors utilizing plasma-deposited fluorocarbon membranes

In this study, plasma-polymerized films are evaluated as enrichment membranes deposited at the surface of mid-infrared transparent waveguides for liquid-phase chemical sensing utilizing evanescent field absorption spectroscopy. Fluorocarbon films were deposited onto zinc selenide (ZnSe) waveguides from plasma-polymerized pentafluoroethane (CF(3)CHF(2)) vapor. Excellent optical transmission of ZnSe waveguides after plasma deposition confirms compatibility of the infrared transparent substrate with this low-temperature, solvent-free film deposition process. The liquid-phase enrichment characteristics for plasma membranes were investigated via evanescent field absorption spectroscopy of a model analyte (tetrachloroethylene); the limits of detection were below 300 ppb (v/v) in water. Plasma-polymerized films are known for their excellent mechanical and chemical stability, while offering tunable chemical and physical characteristics during the deposition process. Future application of this coating strategy for depositing robust enrichment membranes with tunable batch production capability imparts an attractive route toward application-oriented development of next-generation mid-infrared chemical sensors applicable in harsh environments.     

Determination of lead and nickel in environmental samples by flame atomic absorption spectrometry after column solid-phase extraction on Ambersorb-572 with EDTA

Lead and nickel were preconcentrated as their ethylenediaminetetraacedic acid (EDTA) complexes from aqueous sample solutions using a column containing Ambersorb-572 and determined by flame atomic absorption spectrometry (FAAS). pH values, amount of solid phase, elution solution and flow rate of sample solution have been optimized in order to obtain quantitative recovery of the analytes. The effect of interfering ions on the recovery of the analytes has also been investigated. The recoveries of Pb and Ni under the optimum conditions were 99 +/- 2 and 97 +/- 3%, respectively, at 95% confidence level. Seventy-five-fold (using 750 mL of sample solution and 10 mL of eluent) and 50-fold (using 500 mL of sample solution and 10 mL of eluent) preconcentration was obtained for Pb and Ni, respectively. Time of analysis is about 4.5 h (for obtaining enrichment factor of 75). By applying these enrichment factors, the analytical detection limits of Pb and Ni were found as 3.65 and 1.42 ng mL(-1), respectively. The capacity of the sorbent was found as 0.17 and 0.21 mmol g(-1) for Pb and Ni, respectively. The interferences of some cations, such as Mn2+, Co2+, Fe3+, Al3+, Zn2+, Cd2+, Ca2+, Mg2+, K+ and Na+ usually present in water samples were also studied. This procedure was applied to the determination of lead and nickel in parsley, green onion, sea water and waste water samples. The accuracy of the procedure was checked by determining Pb and Ni in standard reference tea leaves sample (GBW-07605). The results demonstrated good agreement with the certified values.     

An ion-imprinted functionalized silica gel sorbent prepared by a surface imprinting technique combined with a sol-gel process for selective solid-phase extraction of cadmium(II)

A new ion-imprinted thiol-functionalized silica gel sorbent was synthesized by a surface imprinting technique in combination with a sol-gel process for selective on-line, solid-phase extraction of Cd(II). The Cd(II)-imprinted thiol-functionalized silica sorbent was characterized by FT-IR, the static adsorption-desorption experiment, and the dynamic adsorption-desorption method. The maximum static adsorption capacity of the ion-imprinted functionalized sorbent was 284 micromol g(-1). The largest selectivity coefficient for Cd(II) in the presence of Pb(II) was over 220. The static uptake capacity and selectivity coefficient of the ion-imprinted functionalized sorbent are higher than those of the nonimprinted sorbent. The breakthrough capacity and dynamic capacity of the imprinted functionalized silica gel sorbent for 4 mg L(-1) of Cd(II) at 5.2 mL min(-1) of sample flow rate were 11.7 and 64.3 micromol g(-1), respectively. No remarkable effect of sample flow rate on the dynamic capacity was observed as the sample flow rate increased from 1.7 to 6.8 mL min(-1). The imprinted functionalized silica gel sorbent offered a fast kinetics for the adsorption and desorption of Cd(II). The prepared ion-imprinted functionalized sorbent was shown to be promising for on-line, solid-phase extraction coupled with flame atomic absorption spectrometry for the determination of trace cadmium in environmental and biological samples. All competitive ions studied did not interfere with the determination of Cd(II). With a sample loading flow rate of 8.8 mL min(-1) for 45-s preconcentration, an enhancement factor of 56, and a detection limit (3sigma) of 0.07 microg L(-1) were achieved at a sampling frequency of 55 h(-1). The precision (RSD) for 11 replicate on-line sorbent extractions of 8 mug L(-1) Cd(II) was 0.9%. The sorbent also offered good linearity (r = 0.9997) for on-line, solid-phase extraction of trace Cd(II).     

浆料固相含量对数字光处理成形Si3N4陶瓷性能的影响

随着科技的不断发展, Si₃N₄陶瓷在航空、机械、生物医疗等高新领域发挥着越来越重要的作用。本工作采用包覆助烧剂Al₂O₃-Y₂O₃后的Si₃N₄粉体为原材料, 利用数字光处理(Digital light processing, DLP)技术成功制备出Si₃N₄陶瓷, 并系统研究了浆料固相含量对Si₃N₄陶瓷浆料、DLP成形Si₃N₄陶瓷素坯和陶瓷性能的影响。研究表明, 浆料固相含量低于40.0% (体积分数)时, 浆料在30 s^-1剪切速率下的粘度均小于2 Pa·s, 可用于DLP成形。在这种情况下, 浆料的单层固化深度随浆料固相含量的增加而减小。随着浆料固相含量的增大, DLP成形Si₃N₄陶瓷的相对密度和抗弯强度先升高后降低。固相含量为37.5% (体积分数)的样品获得最大的相对密度和抗弯强度, 分别为89.8%和162.5 MPa, 较固相含量为32.5% (体积分数)的样品分别提升了10%和16%。本研究通过对陶瓷浆料性能的优化, 提升了DLP成形Si₃N₄陶瓷的性能, 为Si₃N₄等非氧化物陶瓷光固化成形奠定了实验基础。     

高稳定性(EDA)(FA)2[Pb3I10]层状钙钛矿薄膜的制备与表征

为了提高钙钛矿太阳能电池在潮湿环境中的稳定性, 采用一步法, 通过在DMF中混合(EDA)I₂、(FA)I和PbI₂, 将乙二胺离子引入钙钛矿晶格, 成功制备了一种具有较高稳定性的二维片层状的钙钛矿结构薄膜。通过原位掠入射X射线衍射(GIXRD)、X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见吸收光谱(UV-Vis)和原子力显微镜(AFM)等方法检测分析(EDA)(FA)₂[Pb₃I₁₀]在低湿度及高湿度环境下的结构、形貌以及光学性能变化。结果表明: 制备的 (EDA)(FA)₂[Pb₃I₁₀]薄膜在相同湿度环境下比当前广泛应用于钙钛矿太阳能电池的甲胺铅碘薄膜(CH₃NH₃PbI₃)稳定性更高; 薄膜的光学带隙约为1.67 eV, 与太阳能电池最佳带隙比较接近。另外, (EDA)(FA)₂[Pb₃I₁₀]薄膜在可见光范围吸光性能较好; 薄膜的粗糙度很小, 适合制备太阳能电池, 而且, 成本较硅基太阳能电池低廉, 在分子水平较CH₃NH₃PbI₃的可调谐性更大, 使钙钛矿太阳能电池在未来大面积应用成为可能。