Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

Cu-Ce-O/γ-Al_2O_3的CO氧化性能

采用柠檬酸络合法制备一系列不同铜铈比的Cu-Ce-O/γ-Al_2O_3催化剂,用XRD、H2-TPR对其进行表征,采用连续固定床微反装置对Cu-Ce-O/γ-Al_2O_3催化剂CO催化氧化活性进行评价。结果表明,Cu-Ce-O/γ-Al_2O_3催化剂的XRD图谱中除归属于γ-Al_2O_3的晶相峰外,还出现CuO和CeO_2的晶相峰。高温水热引起活性组分CeO_2的晶粒聚集、长大和尖晶石结构CuAl2O4物质的生成;CuO-CeO_2之间的共生共存与相互作用,使得Cu-Ce-O/γ-Al_2O_3催化剂中具有非完整结构的[Cu2+1-xCu+x][O1-12x12x]增多,Cu+离子和氧空位增多,有利于其H2-TPR还原峰温度向低温区偏移,有利于提高其CO的催化氧化活性,使得Cu-Ce-O/γ-Al_2O_3催化剂的TCO50和TCO90降低。Cu与Ce物质的量比为5∶5制备的Cu-Ce-O/γ-Al_2O_3-55催化剂的TCO50和TCO90分别降至最低的162℃和199℃,表明此时的Cu-Ce-O协同效应最佳;CuO-CeO_2二相的共生共存与相互作用有利于减少高温水热环境下活性组分的聚集和晶粒长大,有利于Cu-Ce-O/γ-Al_2O_3催化剂能够保持较高的CO催化氧化活性。     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

M/γ-Al2O3催化剂对煤油水重整制氢的影响

以γ-Al₂O₃为载体,采用等体积分步浸渍法制备了以Ni为活性组分,La、Ce、Fe、Cr、Co为助剂的催化剂M/γ-Al₂O₃,在固定床管式反应器中研究了M/γ-Al₂O₃催化剂的性能,考察了反应温度、水碳比和空速对氢产率的影响,并对催化剂进行XRD、SEM和BET表征。结果表明,NiLaCeFeCrCo/γ-Al₂O₃催化剂具有较好的催化性能,在反应温度700 ℃、水碳物质的量比10和空速6 min^-1的条件下,氢产率达到27.335 mol·mol^-1,并在300 min内表现出较好的活性,平均氢产率为21.966 mol·mol^-1。     

Fe掺杂对Pt-Sn-K/γ-Al_2O_3异丁烷脱氢催化剂性能的影响

采用共沉淀法制备不同Fe含量的Fe(x)-γ-Al_2O_3复合氧化物载体,并采用真空浸渍法制备了Pt-Sn-K/Fe(x)-γ-Al_2O_3催化剂。对制备的催化剂进行XRD、N_2物理吸附-脱附和NH_3-TPD表征,研究Fe的掺杂对Pt-Sn-K/Fe(x)-γ-Al_2O_3催化剂的结构及其催化异丁烷脱氢反应性能的影响。结果表明,Fe的引入可以改变催化剂的反应活性和产物选择性,当Fe_2O_3掺杂质量分数为4%时,催化剂具有最高的异丁烯收率,50 h的平均收率达到42.9%。     

K2CO3/γ-A12O3催化剂在棉籽油制备生物柴油中的应用

利用等体积浸渍法制备K₂CO₃/γ-A1₂O₃负载型固体碱催化剂,应用于棉籽油和甲醇酯交换反应制备生物柴油。对催化剂使用前的保存条件、水分、重复使用性能、游离脂肪酸影响以及失活和再生进行了分析。结果表明,固体催化剂K₂CO₃/γ-Al₂O₃具有较好的抗水性,酸度对催化剂影响明显,重复使用4次未经活化的催化剂,催化活性明显降低,催化剂应密封保存。K₂CO₃/γ-A1₂O₃负载型固体碱催化剂经济实惠且催化效果良好。     

Ce改性Pd基整体式催化剂的结构特征及其甲烷催化燃烧性能

分别以拟薄水铝石和添加Ce的拟薄水铝石制备铝溶胶,经过堇青石（Cord）表面涂覆和Pd溶液浸渍,得到浸渍法和溶胶法Ce改性的Pd/γ-Al₂O₃/Cord整体式催化剂。采用XRD、SEM和XPS等对催化剂进行表征,评价其甲烷催化燃烧反应性能,并考察Ce的不同添加方式对催化剂结构和反应性能的影响。结果表明,适量Ce的添加可提高Pd基整体式催化剂的甲烷催化燃烧性能,溶胶法优于浸渍法。随着Ce添加量的增加,浸渍法改性的Pd基催化剂催化性能有所降低,溶胶法则呈现先升高后降低的趋势。溶胶法中Ce的添加物与γ-Al₂O₃涂层充分融合,提高了涂层的热稳定性和活性组分的分散度,0.5Pd/γ-Al₂O₃(3.0Ce)/Cord催化剂催化性能最优。     

CO oxidation at low temperature over Pd supported on CeO2-TiO2 composite oxide

Low temperature CO oxidation was carried out over CeO₂-TiO₂ composite oxide and thereon supported Pd catalysts. The effects of Ce/Ti ratio and pre-treatments of calcination and reduction on the catalytic behaviour were investigated. The CO oxidation starts at about 220 °C over CeO₂-TiO₂ and the pre-reduction treatment has little influence on the catalytic activity. Pd supported on CeO₂-TiO₂ (Pd/CeO₂-TiO₂) exhibits high activity for CO oxidation and a complete conversion of CO to CO₂ can be achieved even at ambient temperature, which suggests a synergistic effect between Pd and CeO₂-TiO₂. The activity and stability of Pd/CeO₂-TiO₂ can be further improved by the pre-reduction treatment. Ce/Ti ratio influences the catalytic behaviour significantly; the catalyst Pd/CeO₂-TiO₂ with a Ce/Ti mole ratio of 0.20 (Pd/Ce20Ti) owns the highest activity and stability, which suggests an optimization of the Pd-Ce-Ti interaction in Pd/Ce20Ti. The calcined Pd/CeO₂-TiO₂ with a Ce/Ti mole ratio higher than 0.10 shows a distorted light-off profile with the temperature, which implies an alternation of the reaction mechanism with increasing temperature.     

η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Ethylene dimerization over NiSO4 supported on Fe2O3-promoted ZrO2 catalyst

The NiSO₄ supported on Fe₂O₃-promoted ZrO₂ catalysts were prepared by the impregnation method. Fe₂O₃-promoted ZrO₂ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt.%, indicating good dispersion of nickel sulfate on the surface of Fe₂O₃–ZrO₂. The addition of nickel sulfate (or Fe₂O₃) to ZrO₂ shifted the phase transition of ZrO₂ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or Fe₂O₃) and ZrO₂. 15-NiSO₄/5-Fe₂O₃–ZrO₂ containing 15 wt.% NiSO₄ and 5 mol% Fe₂O₃, and calcined at 500 °C exhibited a maximum catalytic activity for ethylene dimerization. NiSO₄/Fe₂O₃–ZrO₂ catalysts was very effective for ethylene dimerization even at room temperature, but Fe₂O₃–ZrO₂ without NiSO₄ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of Fe₂O₃ up to 5 mol% enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between Fe₂O₃ and ZrO₂ and due to consequent formation of Fe–O–Zr bond.     

Deactivation studies over NiO/γ-Al2O3 catalysts for partial oxidation of methane to syngas

Two types of NiO/γ-Al₂O₃ catalysts prepared by the impregnation and the sol–gel method were used for the partial oxidation of methane to syngas at 850°C (GHSV1.8×10⁵ lkg⁻¹ h⁻¹). The effects of the carbon deposition, the loss and sintering of nickel and the phase transformation of γ-Al₂O₃ support on the catalytic performance during 80 h POM reaction were investigated with a series of characterization such as XRD, BET, AAS, TG, and XPS. The results indicated that the carbon deposition and the loss and sintering of nickel could not cause the serious decrease of catalytic performance over NiO/γ-Al₂O₃ catalyst during the short-time reaction. However, the slow process of the support γ-Al₂O₃ phase transforming into -Al₂O₃ could slowly decrease the performance of NiO/γ-Al₂O₃ catalysts. Aimed at the reasons of the deactivation, an improved catalyst was obtained by the complexing agent-assisted sol–gel method.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Thermal evolution of Fe2O3-TiO2 sol-gel thin films

Fe₂O₃-TiO₂ thin films were deposited on silica glass slides using three sol-gel solutions containing Ti-butoxide and different iron oxide precursors. The thermal evolution of the coatings was followed by DTA-TGA and XRD from 200 to 1000°C. All the iron-containing samples were amorphous up to 700°C, when a phase separation between iron and titanium oxides was evidenced by the presence of crystalline Fe₂O₃. Above that temperature a titanate compound (pseudobrookite) formed according to the equilibrium phase diagram. The use of different precursors did not affect the thermal evolution and all the different samples exhibited the same trend.     

CO气相偶联合成草酸二甲酯Pd/α-Al2O3催化剂失活与再利用

作为合成气制乙二醇关键步骤之一,CO与亚硝酸甲酯合成草酸二甲酯备受关注。综述了近年来CO气相偶联合成草酸二甲酯Pd/α-Al₂O₃催化剂失活与再利用研究进展,探讨催化剂再利用工艺存在的问题,指出应根据在工业应用中出现的问题对Pd/α-Al₂O₃催化剂进行失活研究,在此基础上开发针对性的再生工艺;钯催化剂回收方面萃取法和吸附法逐渐成为研究重点,高效、低耗、短流程绿色工艺的开发是失活钯催化剂再利用的发展方向。     

WO_3负载量对V_2O_5/WO_3-TiO_2催化剂脱硝性能的影响

采用V_2O_5/WO_3-TiO_2作为脱硝催化剂,考察活性组分V_2O_5和助剂WO_3负载量对催化剂脱硝活性和抗硫抗水性能的影响。结果表明,3%V_2O_5/x WO_3-TiO_2催化剂(x=3%、4%、5%、6%、7%、8%、9%、10%)上NOx转化率随着WO_3负载量增加而升高,催化剂反应温度窗口不断拓宽。单独通水蒸汽及同时通SO2和水蒸汽对催化剂的毒害作用均较强,表明H2O和NH3的竞争吸附是催化剂抗硫抗水性能较差的重要原因。SO_2与H_2O和NH_3反应生成亚硫酸铵盐和硫酸铵盐,导致催化剂孔隙堵塞,催化活性降低。     

ZrOCl_2-H_2SO_4/γ-Al_2O_3催化剂的制备及对1-丁烯齐聚反应的催化性能

以γ-Al_2O_3为载体,负载Zr OCl_2和H_2SO_4制备Zr OCl_2-H_2SO_4/γ-Al_2O_3催化剂,并用于1-丁烯齐聚反应。采用气相色谱在线分析,确定产物组成,考察制备条件对催化剂催化活性的影响,通过1-丁烯转化率和主产物选择性确定适宜的反应条件。结果表明,在Zr OCl_2和H_2SO_4负载质量分数为4.5%和焙烧温度500℃条件下制备的催化剂,在反应温度140℃、1-丁烯液时空速2 h-1和N2分压1.4 MPa条件下,表现出较好的催化活性,1-丁烯转化率96.77%,产物以二聚体(C8)为主,选择性85.99%。该催化剂失活后容易再生,且催化活性良好,1-丁烯转化率92.73%,C8选择性86.73%。     

柠檬醛在La2O3/γ-Al2O3催化剂上的等温吸附

对柠檬醛-乙酸乙酯溶液中柠檬醛在La₂O₃/γ-Al₂O₃催化剂上等温吸附行为进行了研究。结果表明,30 ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的吸附动力学符合准二阶吸附动力学模型,吸附动力学方程为：1/q_t=2.350/t+0.063 3(R²=0.998 5)。（30~65） ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的等温吸附符合Langmuir方程,温度升高使柠檬醛的饱和吸附量增加,吸附热为32.19 kJ·mol^-1。     

Effect of La on the thermal stability of Pd/γ-Al2O3 catalytic membranes

Lanthanum-doped Pd/γ-Al₂O₃ and Pd/γ-Al₂O₃ membranes were prepared by sol-gel methods. The thermal stability of the unsupported Pd/γ-Al₂O₃ and La/Pd/γ-Al₂O₃ membranes was investigated with BET (including average pore size, pore volume and BET surface area), XRD, and DTA techniques. The average pore size of the Pd/γ-Al₂O₃ membranes increased sharply after sintering at temperatures higher than 1000°C. Addition of 3 mol% lanthanum can raise the temperature of the γ-Al₂O₃ to-Al₂O₃ phase transformation significantly. This improves the thermal stability of the Pd/γ-Al₂O₃ catalytic membranes.     

Co-Cu-Ce-Fe/γ-Al_2O_3催化剂催化分解N_2O的性能

以等体积浸渍法制备γ-Al_2O_3负载的Co、Cu、Ce和Fe氧化物催化剂,利用正交试验设计实验条件,采用XRD、BET和H_2-TPR等对催化剂进行表征,并考察活性组分对催化剂催化分解N_2O活性的影响。结果表明,催化剂具有尖晶石结构,其BET比表面积随着金属氧化物负载量增加而降低。催化剂中铜的氧化物可以降低还原峰温度,进而明显提高催化活性,Co和Fe的加入对活性有一定的提高,Ce对催化活性没有明显影响。