BATCH DRYING OF SHELLED CORN IN TWO-DIMENSIONAL SPOUTED BEDS WITH DRAFT PLATES

ABSTRACT

Geometrically similar spouted beds with draft plates were used to obtain the drying characteristics of freshly harvested shelled corn with 0.28 to 0.31 kg/kg initial moisture content at different air inlet temperatures and bed heights. Thermal equilibrium between air and grains was achieved at minimum spouting conditions. The drying kinetics of shelled corn in a drafted two-dimensional spouted bed was found to be of the "thin layer" type. Expressions for the model parameters in Page's equation accounting for the bed geometry, grain moisture content, and drying conditions were developed.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

CONVECTIVE HEAT TRANSFER DURING COATING OF PARTICLES IN TWO-DIMENSIONAL SPOUTED BEDS

ABSTRACT

This work deals with the evaluation of gas-to-particle convective heat transfer in a process of coating of particles in two-dimensional spouted beds. A detailed calculus routine is presented and two correlations of heat transfer coefficient, for the spout and annular regions are derived. The study is performed with two, two-dimensional spouted beds with different sizes and with two different particles, placebo and soybean.     

PREDICTION OF MINIMUM SPOUTING VELOCITY IN TWO-DIMENSIONAL FLAT BOTTOM SPOUTED BEDS

Spouted beds have been used in industry for operations such as drying, catalytic reactions, and granulation. Conventional cylindrical spouted beds suffer from the disadvantage of scaleup. Two-dimensional beds have been proposed by other authors as a solution for this problem. Minimum spouting velocity has been studied for such two-dimensional beds. A force balance model has been developed to predict the minimum spouting velocity and the maximum pressure drop. Effect of porosity on minimum spouting velocity and maximum pressure drop has been studied using the model. The predictions are in good agreement with the experiments as well as with the experimental results of other investigators.     

SPOUTED AND SPOUT-FLUIDIZED BEDS FOR GRAM DRYING

The objectives of this work are to analyze the drying performance of conical-cylindrical spouted bed (CSB) dryers for three different grains (rice, corn and wheat), and to compare the drying efficiency of CSB dryers with that of spout-fluid bed (SFB) dryers. A PC-program was developed for: (I) -optimization of the CSB dryer dimensions; (2) -simulation of drying grains in the optimized CSB dryer (including start-up period); and, (3) -analysis of the drying performance in a similar SFB dryer.

The liquid diffusion model is used to describe the falling rate drying period. Semi-empirical correlations available in the literature as well as information obtained in the authors' laboratory for spouted and spout-fluidized beds of grains are used to describe the aerodynamic parameters.

The results are presented in terms of the size of the dryer, energy consumption, air handling requirement, drying characteristics etc for different drying conditions. The drying effeciency in a CSB is compared with that in a similar SFB for different grain feed rates and drying temperatures.     

SPOUTED AND SPOUT-FLUIDIZED BEDS FOR GRAM DRYING

The objectives of this work are to analyze the drying performance of conical-cylindrical spouted bed (CSB) dryers for three different grains (rice, corn and wheat), and to compare the drying efficiency of CSB dryers with that of spout-fluid bed (SFB) dryers. A PC-program was developed for: (I) -optimization of the CSB dryer dimensions; (2) -simulation of drying grains in the optimized CSB dryer (including start-up period); and, (3) -analysis of the drying performance in a similar SFB dryer.

The liquid diffusion model is used to describe the falling rate drying period. Semi-empirical correlations available in the literature as well as information obtained in the authors' laboratory for spouted and spout-fluidized beds of grains are used to describe the aerodynamic parameters.

The results are presented in terms of the size of the dryer, energy consumption, air handling requirement, drying characteristics etc for different drying conditions. The drying effeciency in a CSB is compared with that in a similar SFB for different grain feed rates and drying temperatures.     

导向管充气喷动床流体力学性能

在内径92mm的有机玻璃床内,对导向管充气喷动床的操作相图、床层压降、最小喷动速度及最大弃气速度进行了研究.实验采用4种颗粒为实验物料并采用空气为 喷动和弃气气体,通过对实验数据的回归得到用于计算或判别导向管弃气喷动床最小喷动速度和最大充气速度的计算式,以便为其设计和操作提供依据.     

THE INFLUENCE OF POLARIZATION ON THE MICROWAVE DRYING PROCESS OF SHELLED CORN

In this paper the effect of electromagnetic polarization of the microwave field on drying of shelled corn was analyzed. The drying process was investigated in a microwave field of 2.45 GHz. A number of corn kernels with the same orientation were stocked on plastic plates and these plates with corn kernels on their surfaces were fixed to each other, creating the corn matrixes. Plastic plates and glue used to the experiments were inert, related to the applied microwave power. By rotating test materials the influence of different polarization angles of electromagnetic field could be registered. Furthermore, setting test material in different positions the effect of distance between the antenna and the corn matrix were observed

The experiments carried out showed that in moist crops placed in microwave field ion polarization is dominant and the drying rate depends on relationship between the electric field strength vector and the overall moisture gradient in the kernel.     

THE INFLUENCE OF POLARIZATION ON THE MICROWAVE DRYING PROCESS OF SHELLED CORN

ABSTRACT

In this paper the effect of electromagnetic polarization of the microwave field on drying of shelled corn was analyzed. The drying process was investigated in a microwave field of 2.45 GHz. A number of corn kernels with the same orientation were stocked on plastic plates and these plates with corn kernels on their surfaces were fixed to each other, creating the corn matrixes. Plastic plates and glue used to the experiments were inert, related to the applied microwave power. By rotating test materials the influence of different polarization angles of electromagnetic field could be registered. Furthermore, setting test material in different positions the effect of distance between the antenna and the corn matrix were observed

The experiments carried out showed that in moist crops placed in microwave field ion polarization is dominant and the drying rate depends on relationship between the electric field strength vector and the overall moisture gradient in the kernel.     

超细粉在导向管喷动床中的固体循环速率

Ultra-fine powders are difficult to be fluidized due to the strong particle to particle cohesiveness.However, the authors‘ experiments showed that the ultra-fine powder CaCO3 could be stably fluidized in a spouted bed with a draft tube. The effects of geometric and operating parameters on solid circulation rate of ultra-fine powder CaCO3 were investigated in a 120 mm diameter transparent semicircular spouted bed with a draft tube. Three draft tubes with different sizes were used in this study. It was found that the solids circulation rate was mainly dependent on the drawing rate of the gas jet from the nozzle, then on the gas transport capacity in the draft tube. With increasing gas feed rate, distance between the nozzle and the draft tube inlet and draft tube diameter, the solids circulation rate could be increased. Based on the jet theory, a quantitative correlation was proposed for predicting the solid circulation rate of ultra-fine powders in a spouted bed with a draft tube by taking into account the gas transport capacity in the draft tube.     

SOLIDS CIRCULATION IN SPOUTED AND SPOUT-FLUID BEDS WITH DRAFT-TUBES

A 20 cm semi-cylindrical spout-fluid bed with a draft-tube has been used to investigate the effect of various physical parameters on the solids circulation rate, A new method has been developed by which these data can be easily and accurately collected. Equations are presented which can be used to predict the maximum attainable solids circulation rate and the spouting velocity required to achieve this maximum for the unit operating in spouting mode. The circulation trends are shown to be a direct result of the phenomena of entrainment and jetting occurring in the entrainment zone investigated visually with a video camera. Preliminary gas bypassing experiments were also performed which show the ability to almost eliminate spout gas bypassing to the annulus with appropriate auxiliary gas addition.     

HEAT TRANSFER IN SPOUTED BEDS

Experiments were carried out in order to analyse the wall-to-bed and fluid-to-particle heat transfer coefficients in spouted Beds. wall-to-bed heat transfer coefficients were determined in cylindrical-conical and conical spouted beds for various gas flow rates, particle sizes and bed heights for spouted beds with and without draft tubes.

A new definition for wall-to-bed transfer coefficient was proposed baaed on experimental observations.

The heat tranefer area was also studied to ensure that a physically significant fluid-to-particle heat transfer coefficient was achieved.     

DRYING SIMULATION OF CORN WITH TEMPERING

This work presents a dirTusion model and experimental investigation or com drying with tempering. The model solves numerically the dirTusion equation for a hygroscopic porous solid consisting of two concentric spheres (starchy endosperm and pericarp) with different shell thickness and relative resistances to moisture flow. Multipass drying was simulated to evaluate the effect of tempering on drying process. Predicted moisture profiles within the kernel were used to evaluate the actual time for complete tempering or tempering index. The effect of the initial moisture for tempering and the number of drying passes on the net drying time were analyzed. A mathematical expression was formulated to estimate the tempering index under different tempering conditions.     

DRYING SIMULATION OF CORN WITH TEMPERING

Abstract

This work presents a dirTusion model and experimental investigation or com drying with tempering. The model solves numerically the dirTusion equation for a hygroscopic porous solid consisting of two concentric spheres (starchy endosperm and pericarp) with different shell thickness and relative resistances to moisture flow. Multipass drying was simulated to evaluate the effect of tempering on drying process. Predicted moisture profiles within the kernel were used to evaluate the actual time for complete tempering or tempering index. The effect of the initial moisture for tempering and the number of drying passes on the net drying time were analyzed. A mathematical expression was formulated to estimate the tempering index under different tempering conditions.     

喷动床内气固两相流体动力行为的数值模拟

引　言喷动床被广泛应用于不同工业领域中 ,如石油裂解反应 -再生器、煤和农业废弃物气化和燃烧 ,喷动床还被应用于粮食和药品的干燥等[1] .因此 ,喷动床设计应满足不同应用的要求 .喷动床内气相反应物的反应时间和停留时间依赖于床体几何结构和运行参数 .尽管已有许多的实验对喷动床内气固两相流动进行了研究 ,得到了喷射区、环形区和喷泉区内的气固两相流动流体动力特性 ,然而由于喷动床内气固两相流动的复杂性 ,人们对床体几何结构和运行参数对喷动床动力学的影响至今并不清楚 .因此 ,床体几何结构和运行参数等对喷动床动力学的影响成为…