The resistance degradation of (Ba0.5Sr0.5)TiO3 thin films

Abstract

The leakage current and dielectric properties of (Ba_0.5Sr_0.5)TiO₃(BST) thin films prepared by pulsed laser deposition (PLD) were investigated. It was found that leakage currents for positive bias voltage were higher than that for negative bias voltage, which was attributed to the lattice mismatch between bottom Pt electrode and BST thin film. The time-dependent breakdown process under positive voltage was observed, which was interpreted as the increase of the internal electric field in the film near the bottom electrode. However, the internal electric field can be decreased and eventually recovered by applying negative bias voltage. It was found that internal electric field near the interface can influence the capacitance of the BST thin film capacitor. An explanation for the thickness effect of BST thin films was given.     

Microwave Tunable Properties of Ni-Doped (Ba0.5Sr0.5)TiO3 Thin Films Grown by Pulsed Laser Deposition

(Ba_0.5Sr_0.5)TiO₃ (BST) thin films were deposited by pulsed laser deposition (PLD) and investigated as a function of Ni dopant concentration in low and high frequency regions. In low frequency region (<10 MHz), the Ni-dopant concentration in BST films has a strong influence on the material properties including dielectric and tunable properties. Ni-doped (≤3 mol%) BST films showed denser, smoother morphologies and smaller grain sizes than those with 6 and 12 mol% Ni. Dielectric constant and loss of 3 mol% Ni-doped BST films were about 980 and 0.3%, respectively. In addition, tunability and figure of merit of 3 mol% doped BST films showed maximum values of approximately 39% and 108, respectively. In high frequency region (>1 GHz), the frequency tunability range at center frequency of undoped BST and 3 mol% Ni-doped BST coplanar waveguide (CPW) resonators showed 102 and 152 MHz, respectively at 30 V dc bias. The Ni-doped BST thin films are possible in applications of microwave tunable capacitors.     

Dielectric Properties of Ba0.5Sr0.5TiO3 Thin Films from DC to Ka Band

Much of the interest in Ba_0.5Sr_0.5TiO₃ (BST) thin films has focused on DRAM applications. For this application, the most studied characteristics have been the dielectric constant and the leakage current, both of which are usually measured either at DC or at low frequencies. A few studies have made use of impedance measurements in the 100 Hz to 100 MHz range. Unfortunately, all these measurements fall far short of current DRAM speeds, which are quickly approaching 1 GHz. Other technologies, such as digital computing and wireless communications are already well into the microwave range. The importance of microwave characterization of BST films is therefore clear. Such a characterization technique is described and results from DC to Ka band are presented.     

Low dielectric dissipation and enhanced tunability of Ba0.6Sr0.4TiO3 thin films by the modified composition and multilayer structure

Ba_0.6Sr_0.4Ti_1+yO₃ (BST, y?=?0.1, 0.15, 0.2, 0.25, 0.3) thin films were fabricated on Pt-coated silicon substrates by modified sol-gel techniques. It was found that the tunability of BST thin films and dissipation factor decreased with the increase of Ti content. The multilayer structure of Ba_0.6Sr_0.4Ti_1+yO₃(200 nm)/Ba_0.6Sr_0.4TiO₃(100 nm)/Ba_0.6Sr_0.4Ti_1+yO₃ (200 nm; y?=?0.1, 0.2, 0.25) was designed to enhance the tunability. Our results indicated that the modified composition and multilayer structure were beneficial to lowering the dielectric dissipation and enhancing the tunability simultaneously. The tunability of 26.7% and dielectric dissipation of 0.013 were achieved for modified BST thin films.     

Structure and dielectric properties of Ca-doped (Ba0.7Sr0.3) TiO3 thin films fabricated by sol–gel method

A wide range of Ca-doped (Ba_0.7Sr_0.3)TiO₃ (BST) thin films (from 0 to 20 mol%) have been prepared on Pt/Ti/SiO₂/Si (100) substrates by sol–gel technique. The structural and dielectric properties of BST thin films were investigated as a function of Ca dopant concentration. The results showed that the microstructure and dielectric properties of the BST films were strongly dependent on the Ca contents. With the Ca dopant concentration increasing, the grain size, dielectric constant and dielectric loss of the BST thin films decreased. As the content of Ca dopant reaches 10 mol%, the dielectric constant, dielectric loss, tunability, the value of FOM and the leakage current density are 281, 0.0136, 16.7%, 12.3 and 5.5?×?10^?6 A/cm², respectively.     

The Effect of Stress on the Microwave Dielectric Properties of Ba0.5Sr0.5TiO3 Thin Films

Single phase, (1 0 0) epitaxial Ba_0.5Sr_0.5TiO₃ (BST) films have been deposited onto (1 0 0) LaAlO₃ and MgO substrates by pulsed laser deposition (PLD). The capacitance and dielectric losses of as-deposited and annealed films have been measured from 1–20 GHz as a function of electric field (0–80 kV/cm) at room temperature. The dielectric properties are strongly affected by the substrate type, post-deposition annealing time (6 h) and temperature (1200°C). For epitaxial BST films deposited onto MgO, it is observed that, after a post-deposition anneal the dielectric constant and the dielectric loss decreases. For epitaxial BST films deposited onto LAO, a post-deposition anneal (1000°C) results in an increase in the dielectric constant and an increase in the dielectric loss. The dc electric field induced change in the dielectric constant tends to increase with the dielectric constant and is largest for as-deposited films on MgO and post-deposited annealed films on LAO. In general, for epitaxial BST films, a large electric field effect is observed in films that have a large dielectric loss and a small electric field effect in films that have a low dielectric loss. High resolution X-ray diffraction measurements indicate that deposited film exhibit a significant tetragonal distortion which is strongly affected by a by a post deposition anneal. The observed differences in dielectric properties of the epitaxial BST films on MgO and LAO are attributed to the differences in film stress which arise as a consequence of the lattice mismatch between the film and the substrate and the differences in the thermal coefficient of expansion between the film and the substrate. A thin amorphous buffer layer of BST has been used to relieve stress induced by the lattice mismatch between the film and the substrate. Unlike epitaxial films, stress relieved films do not show an inverse relationship between dielectric tuning and Q (1/tan) and may be superior materials for tunable microwave devices.     

Magnetron sputter-deposited multilayer (BaxSr1x)Ti1+yO3+z thin films for passive and active devices

Abstract

High permittivity (Ba_xSr_1?x)Ti_1+yO_3+z(BST) thin films are being investigated for integration into charge storage dielectrics and electric-field tunable elements for high frequency devices. For the latter application, it is desirable to have BST capacitors with high tunability and low losses. Therefore, we investigated the use of multilayer BST thin films consisting of very low dielectric loss BST/electrode interfacial layers ((Ba+Sr)/Ti = 0.73) sandwiching a high tunability, high permittivity primary BST layer ((Ba+Sr)/Ti = 0.9). BST capacitors with multiple layers of controlled composition can be effectively produced insitu by magnetron sputter deposition, using a single stoichiometric target and controlling the layer composition by changing the total process gas (Ar+O<₂) pressure. The layered BST film capacitors exhibit simultaneous low loss (tan Δ = 0.005), high tunability (76%), high charge storage energy density (34 J/cm³), low leakage, and high dielectric breakdown (>2.8 MV/cm).     

Characterization of Ni/Ce Co-Doped BST Thin Film Grown on LSCO/Pt Electrodes Prepared by Pulsed Laser Deposition

Perovskite (Ba_0.6Sr_0.4)TiO₃ (BST) thin films doped with Ni, Ce and Ni/Ce codopants were prepared on LSCO/Pt/SiO₂/Si substrates by pulsed laser deposition method. In this study, La_0.5Sr_0.5CoO₃ (LSCO) bottom electrodes were used to improve the crystallinity and dielectric properties of BST films. Single ion doped(1 mol%Ni doped,1 mol%Ce doped) BST films showed more improved crystallinity, smoother surface, and smaller grain size than that with 1 mol%Ni/1 mol%Ce. The dielectric constant and loss of Ni/Ce co-doped BST films were about 298 and 1.8%, respectively. In addition, tunability and figure of merit of co-doped BST films showed minimum values of approximately 9.3% and 5, respectively. With 1% Ni-doped BST thin films, results gave a tunability of 54.2% and a loss tangent of 1.8% while a figure of merit was 30. Correlation of the material properties with dielectric and tunable properties suggests the 1 mol%Ni-doped BST films are effective potential candidate for tunable device applications.     

The electrical properties of Ba1-x SrxTiO3 thin films grown by sputter deposition

Abstract

Ba_1-x Sr_xTiO₃ (BST) thin films were deposited by reactive rf-magnetron sputtering onto Si substrates. The influence of the deposition parameters such as temperature and oxygen ambient on the dielectric constant of the films is presented. BST films deposited at 450°C and optimum conditions exhibited a dielectric constant of approximately 200 at frequencies as high as 1GHz. In addition, the films were found to have leakage current densities of <0.1μAmp/cm² at fields of 5×10⁵V/cm. An extrapolated lifetime greater than 10 years was obtained from stress tests at elevated temperatures and fields. These films compared favorably with published data.     

STRESS CONTROLLED FERROELECTRIC (BA0.5Sr0.5)TiO3 THIN FILMS PREPARED ON GD2O3/SRTiO3(001) BY A PULSED LASER DEPOSITION

ABSTRACT

Stress controlled epitaxial ferroelectric Ba_0.5Sr_0.5TiO₃ (BST) films have been deposited on Gd₂O₃/SrTiO₃ by pulsed laser deposition with oxygen background pressure of 200 mTorr at the deposition temperature of 750°C. In order to control the stress in BST films, oxygen pressures for Gd₂O₃ buffer layers have been varied from 0.1 to 100 mTorr, while that of BST films have been fixed at 200 mTorr. It has been found that the lattice parameters of the BST films deposited on Gd₂O₃ were changed. Furthermore, microwave properties of co-planar waveguide (CPW) fabricated on BST films were investigated by a HP 8510C vector network analyzer from 1–20 GHz. Large dielectric tunabilities were observed from the CPW's fabricated on BST films deposited on Gd₂O₃ layers deposited at low and high oxygen pressures, 0.1 and 100 mTorr, respectively.     

Thickness dependent performance of Na0.5K0.5NbO3/sapphire thin film varactors

Abstract

Perfect c-axis oriented Na_0.5K_0.5NbO₃ (NKN) films have been pulsed laser deposited on Al₂O₃(0112) single crystals (r-cut sapphire) for voltage tunable microwave device applications. Thickness dependence of dielectric performance of the NKN/sapphire interdigital capacitors (IDCs) has been studied. 40 V bias tunability and dielectric loss tan δ of 4 μm slot IDCs have been found to be 24.6 % and 2.86 % for 1.2 μm thick NKN film, and 6.1 % and 0.83 % for 0.14 μm thick NKN film, respectively. Low leakage currents and high breakdown voltages are observed in these structures.     

Microwave Characterization of BST Thin Films on LAO Interdigital Capacitor

The dielectric properties of (Ba_0.5Sr_0.5)TiO₃ (BST) thin films on LaAlO₃ (LAO) single crystals were studied over a wide frequency range. The samples with interdigital electrodes were prepared by microelectronic processing. The dielectric characterizations were carried out in the following steps: 1) the standard calibration of the instrument, 2) the removal of parasitic capacitance and the extraction of the capacitance of the interdigital capacitor (IDC) and 3) the extraction of the dielectric permittivity (?) of BST. It was found that ? of BST has a constant value (about 400) from 50 MHz to 2 GHz; at higher frequencies, ? gradually decreases. The BST interdigital capacitors exhibited good dielectric tunability.     

Effect of seed layers on dielectric properties of Ba(Zr0.3Ti0.7)O3 thin films

The Barium zirconium titanate Ba(Zr_0.3Ti_0.7)O₃ thin films were prepared on Pt/Ti/SiO₂/Si substrates with seed layers at the BZT/Pt interface by sol–gel process. Microstructure and structure of thin films were examined. Dielectric properties of thin films with various seed layers thicknesses were investigated as a function of frequency and direct current electric field. The tunability and dielectric constant of BZT thin films increased with increasing seed layer thickness from 0 to 20 nm, while it decreased with a further increase in thickness above 20 nm, meanwhile, the leakage current showed the similar tendency at applied electric field of 250 kV/cm. The optimized seed layer thickness for BZT thin films plays an important role in maintaining the high tunability and low leakage current, which are suitable for microwave device applications.     

Thickness dependent ferroelectric properties of BSTO thin films deposited by RF magnetron sputtering

The thickness dependence of ferroelectric permittivity of (Ba, Sr)TiO₃ has been investigated. The BST films could be obtained to have a simple cubic perovskite structure, space group Pm3m, and practically c-axis epitaxial structure deposited at 800^∘C. Through post-annealing process, we have improved the dielectric properties; dielectric permittivity, dielectric loss, and tunability. The change in dielectric properties before and after annealing is attributed to the change in film strain and the contraction in film lattice. As the thickness of BST films increases from 55 nm to 350 nm, the dielectric constant of BST films increases from about 100 to above 670 due to the reduction of interfacial dead layers with low dielectric constant between films and top electrodes. The dielectric loss of BST thin films decreased as the thickness increases. The existence of interfacial dead layers in a thinner film had a larger effect on the effective dielectric constant than tensile strain between the BST films and MgO substrate.     

Calculation of the intrinsic dead layers thicknesses from Au/Ba0.5Sr0.5TiO3/Pt thin film capacitors

Ferroelectric Ba_0.5Sr_0.5TiO₃ (BST) films were prepared on Pt/Ti/SiO₂/Si substrates by the sol-gel process. The films were spin-coated at 2000 rpm for 30 secs and then pyrolysed for 5 mins at the temperature of 350^∘C. This coating procedure was repeated for 3, 4, 5 and 6 times to obtain BST films with different thicknesses. After coating the films with the desired repetition times, the films were finally annealed in a conventional furnace at temperatures ranging from 600^∘C to 800^∘C with a 50^∘C interval in between. The films obtained with an annealing procedure of 750^∘C were polycrystalline with the presence of an impurity BaCO₃ phase. The capacitance and leakage current were measured and used to extract information on the metal-BST interface. With the series capacitance model and modified Schottky emission equation, the thickness of the dead layers for Au/BST and Pt/BST interfaces were calculated to be less than 6 nm and 5 nm, respectively.     

Influence of Y and Mn alternately doped order on the microstructures and dielectric properties of Ba0.6Sr0.4TiO3 films

ABSTRACT

The influences of Y and Mn alternately doped order on the microstructures and dielectric properties of the Ba_0.6Sr_0.4TiO₃ (BST) films were reported in this paper. The Y and Mn alternately doped BST films were designed as YBST/MnBST/… and MnBST/YBST…multilayer films orderly expressed as (Y/Mn)_M and (Mn/Y)_M for short, and prepared on Pt/Ti/SiO₂/Si wafers by an improved sol-gel method, where Y and Mn represent yttrium doped BST layer and manganese doped BST layer, and M is cycle unit, respectively. The microstructures of the alternately doped BST films were observed by SEM and the capacitance-voltage curves at 100 kHz or 1 MHz were measured by a HP4284A LCR meter and the dielectric properties in the range of 1GHz were measured by an E4991A impedance analyzer. Compared to Y or Mn doped multilayer BST film, (Y/Mn)_M and (Mn/Y)_M show higher dielectric tunability and lower dielectric loss with higher dielectric constant. Moreover, (Y/Mn)_M show better dielectric properties than (Mn/Y)_M because (Y/Mn)_M show granular microstructures independent of M, while the (Mn/Y)_M show granular microstructures when M is 2 and add to a surface layer of columnar microstructures on the granular microstructures when M is 4. The related mechanisms were obtained in terms of the XRD phase structures, the cross-sectional SEM microstructures and the AFM morphologies.     

Iridium thin film as a bottom electrode for high dielectric (Ba,Sr)TiO3 capacitors

Abstract

We propose Ir thin films as new electrode materials for high dielectric BST capacitors. Ir was found to be superior to Pt in a number of aspects such as resistivity, adhesion and surface roughness. The Pt/BST/Ir/SiO₂/Si capacitors showed leakage currents as low as Pt/BST/Pt/SiO₂/Si ones, but higher capacitance resulted. For endurance properties with +5V unipolar pulse trains, the dielectric constant of BST films on Ir decreased by only 10% below its initial value after switching of 10⁹ cycles while that on Pt degraded by 30% after 10⁸ cycles. Ir bottom electrode effects on BST film properties were well explained by the formation of IrO₂ phases on the surface of Ir electrodes.     

Dielectric tunability and microwave properties of Ba0.5Sr0.5TiO3-BaMg6Ti6O19 composite ceramics for tunable microwave device applications

Ba_0.5Sr_0.5TiO₃-BaMg₆Ti₆O₁₉ microwave composite ceramics with low dielectric constant and relatively high tunability were fabricated via the solid-state reaction method. The microstructures and microwave dielectric properties of the composite ceramics have been investigated. BaMg₆Ti₆O₁₉ and Ba_0.5Sr_0.5TiO₃ can be friendly coexistent in the composite material system without obvious chemical reactions. With increasing content of BaMg₆Ti₆O₁₉ from 10 wt.% to 60 wt.%, the dielectric anomalous peaks of ferroelectric-paraelectric phase transition for the composite ceramics are suppressed and broadened. The dielectric constant can be effectively tailored from 2035 to 129. For composite ceramics with 60 wt.% content of BaMg₆Ti₆O₁₉, the dielectric loss still keeps around 0.002 and the tunability is 13.4% measured at a dc-applied electric field of 30 kV/cm. The Q value of composite ceramics with 20 wt.% content BaMg₆Ti₆O₁₉ is 367 and the dielectric constant is cut down to 665 at the microwave band of 1.579 GHz.     

PREPARATION AND PROPERTIES OF LITHIUM-DOPED K0.5Na0.5NbO3 THIN FILMS BY CHEMICAL SOLUTION DEPOSITION

ABSTRACT

Lithium-doped K_0.5Na_0.5NbO₃ (KLNN) films were fabricated by chemical solution deposition on Pt/TiO₂/SiO₂/Si substrates. Homogeneous and stable precursor solutions were prepared by controlling the reaction of starting metal alkoxides. Perovskite KLNN single-phase thin films were successfully synthesized on Pt/TiO _x /SiO₂/Si substrates. The 0.75-μ m-thick KLNN film annealed at 650°C exhibited ferroelectric polarization hysteresis loops at ?250°C. The loop at room temperature was round, indicating the film contained leakage components. The dielectric constant under zero bias was 490 at room temperature. A typical upside-down butterfly DC bias-capacitance curve was obtained in the KLNN film capacitors at room temperature, indicating that polarization reversal occurred in the obtained KLNN films.     

Epitaxial Ba0.5Sr0.5TiO3 thin films for microwave phase shifters

Abstract

A tunable phase shifter was fabricated with epitaxial Ba_0.5Sr_0.5TiO₃ (BST) thin film and gold coplanar waveguide. BST thin film of the thickness ～0.5 μm was deposited by laser ablation on the MgO(OOl) single crystalline substrate. Gold electrode of the thickness ～2 μm was prepared by the sequence of thermal evaporation, electroplating, and wet etching. Epitaxial quality of the BST thin film was confirmed by X-ray diffraction. The microwave performance of phase shifter was measured at room temperature in the frequency range of 8–12 GHz, and with applied bias voltage of up to 30 V. Effect of Mn dopant in the epitaxial films was also considered.