A ZrB2–SiC/SiC oxidation protective dual-layer coating for carbon/carbon composites

In order to improve the oxidation resistance of C/C composites, a ZrB₂–SiC/SiC oxidation protective dual-layer coating was prepared by a pack cementation combined with the slurry paste method. The phase and microstructure of the coating were characterised by X-ray diffraction, scanning electron microscope and energy-dispersive spectrometer analyses. The anti-oxidation and thermal shock resistance of the coating were also investigated. It was found that the ZrB₂–SiC/SiC coating could effectively improve the oxidation resistance of the C/C composites. The weight loss of the coated samples was only 1.8% after oxidation at 1773?K for 18?h in air. The coating endured 20 thermal shock cycles between 1773?K and room temperature with only 4.6% weight loss.     

TaB2–SiC–Si multiphase oxidation protective coating for SiC-coated carbon/carbon composites

To improve the oxidation resistance of the carbon/carbon (C/C) composites, a TaB₂–SiC–Si multiphase oxidation protective ceramic coating was prepared on the surface of SiC coated C/C composites by pack cementation. Results showed that the outer multiphase coating was mainly composed of TaB₂, SiC and Si. The multilayer coating is about 200 μm in thickness, which has no penetration crack or big hole. The coating could protect C/C from oxidation for 300 h with only 0.26 × 10^?2 g²/cm² mass loss at 1773 K in air. The formed silicate glass layer containing SiO₂ and tantalum oxides can not only seal the defects in the coating, but also reduce oxygen diffusion rates, thus improving the oxidation resistance.     

A SiC–Si–ZrB2 multiphase oxidation protective ceramic coating for SiC-coated carbon/carbon composites

In order to improve the oxidation protective ability of SiC-coated carbon/carbon (C/C) composites, a SiC–Si–ZrB₂ multiphase ceramic coating was prepared on the surface of SiC-coated C/C composite by the process of pack cementation. The microstructures of the coating were characterized using X-ray diffraction and scanning electron microscopy. The coating was found to be composed of SiC, Si and ZrB₂. The oxidation resistance of the coated specimens was investigated at 1773 K. The results show that the SiC–Si–ZrB₂ can protect C/C against oxidation at 1773 K for more than 386 h. The excellent oxidation protective performance is attributed to the integrity and stability of SiO₂ glass improved by the formation of ZrSiO₄ phase during oxidation. The coated specimens were given thermal shocks between 1773 K and room temperature for 20 times. After thermal shocks, the residual flexural strength of the coated C/C composites was decreased by 16.3%.     

ZrB2–SiC gradient oxidation protective coating for carbon/carbon composites

To improve the oxidation protective ability of carbon/carbon composites, ZrB₂–SiC gradient coating was prepared on the surface of C/C composites by an in-situ reaction method. The ZrB₂–SiC gradient coating consisted of an inner ZrB₂–SiC layer and an outer ZrB₂–SiC–Si coating. The phase composition and microstructures of the multiphase coating were characterized by XRD, EDS and SEM. Results showed that the inner coating is mainly composed of ZrB₂ and SiC, while the outer multiphase coating is composed of ZrB₂, SiC and Si. The multilayer coating is about 200 μm in thickness, which has no penetration crack or big hole. The oxidation behavior of the coated C/C composites at 1773 K in air was investigated. Results show that the gradient ZrB₂–SiC oxidation protective coating could protect C/C from oxidation for 207 h with only (4.56±1.2)×10⁻³ g/cm² weight loss, owing to the compound silicate glass layer with the existence of thermally stable phase ZrSiO₄.     

Ablation behavior of ZrB2–SiC protective coating for carbon/carbon composites

Ablation behavior of ZrB₂–SiC protective coating for carbon/carbon composites during oxyacetylene flame test at 2500 °C was investigated by analyzing the microstructure differentiation caused by the increasing intensity of ablation from the border to the center of the surface. After ablation, a continuous SiO₂ scale, a porous SiO₂ layer inlaid with fine ZrO₂ nuclei, and a continuous ZrO₂ scale respectively emerged in the border region, the transitional region, and the center region. In order to investigate the ablation microstructure in the initial stage, the sub-layer microstructure was characterized and found to be mainly formed by coral-like structures of ZrO₂, which showed huge difference with the continuous structure of ZrO₂ on the surface layer. A kinetic model concerning the thickness change induced by volatilization and oxidation during ablation was built to explain the different growth mechanisms of the continuous ZrO₂ scale and the coral-like ZrO₂ structure.     

Effect of silicon/graphite ratio and temperature on oxidation protective properties of SiC/ZrB2–SiC coatings prepared by pack cementation

To investigate the silicon/graphite ratio and temperature on preparation and properties of ZrB₂–SiC coatings, ZrB₂, silicon, and graphite powders were used as pack powders to prepare ZrB₂–SiC coatings on SiC coated graphite samples at different temperatures by pack cementation method. The composition, microstructure, thermal shock, and oxidation resistance of these coatings were characterized and assessed. High silicon/graphite ratio (in this case, 2) did not guarantee higher coating density, instead could be harmful to coating formation and led to the lump of pack powders, especially at temperatures of 2100 and 2200 °C. But residual silicon in the coating is beneficial for high density and oxidation protection ability. The SiC/ZrB₂–SiC (ZS50-2) coating prepared at 2000 °C showed excellent oxidation protective ability, owing to the residual silicon in the coating and dense coating structure. The weight loss of ZS50-2 after 15 thermal shocks between 1500 °C and room temperature, and oxidation for 19 h at 1500 °C are 6.5% and 2.9%, respectively.     

Ablation resistance of HfC–SiC coating prepared by supersonic atmospheric plasma spraying for SiC-coated C/C composites

In order to improve the ablation properties of carbon/carbon composites, HfC–SiC coating was deposited on the surface of SiC-coated C/C composites by supersonic atmospheric plasma spraying. The morphology and microstructure of HfC–SiC coating were characterized by SEM and XRD. The ablation resistance test was carried out by oxyacetylene torch. The results show that the structure of coating is dense and the as-prepared HfC–SiC coating can protect the C/C composites against ablation. After ablation for 30 s, the linear ablation rate and mass ablation rate of the coating are −0.44 μm/s and 0.18 mg/s, respectively. In the ablation center region, a Hf–Si–O compound oxide layer is generated on the surface of HfC–SiC coating, which is conducive to protecting the C/C composites from ablation. With the ablation time increasing to 60 s, the linear ablation rate and mass ablation rate are changed to −0.38 μm/s and 0.26 mg/s, respectively. Meanwhile, the thickness of the outer Hf–Si–O compound layer also increases.     

Enhanced bonding strength and thermal cycling performance of MoSi2–CrSi2–SiC–Si coating for carbon/carbon composites by surface modification via blasting treatment

Before the preparation of MoSi₂–CrSi₂–SiC–Si coating, blasting treatment of carbon/carbon (C/C) composites, as a surface modification method, was conducted under oxyacetylene torch. MoSi₂–CrSi₂–SiC–Si coating was prepared on the treated C/C composites by pack cementation, where an interlock interface was formed between the coating and the C/C substrate. After blasting treatment, the thermal expansion coefficient mismatch between the coating and C/C substrate was alleviated efficiently, and the bonding strength of the coating was increased by 45.6% and reached 26.2 MPa. To simulate the real working condition, thermal cycling test was conducted under oxyacetylene torch from 1600 °C to room temperature to construct an environment of combustion gas erosion. Due to the improvement of bonding strength and the alleviation of thermal expansion coefficient mismatch between the coating and the C/C substrate, thermal cycling performance of MoSi₂–CrSi₂–SiC–Si coating was enhanced. After 25 thermal cycles, the mass loss of the coated C/C composites without blasting treatment was up to 2.4%, and the C/C substrate was partially exposed. In contrast, the mass loss of the coated C/C composites with blasting treatment was only 1.1%.     

Microstructure and oxidation resistance of C-AlPO4–mullite coating prepared by hydrothermal electrophoretic deposition for SiC-C/C composites

Oxidation resistant C-AlPO₄–mullite coating for SiC pre-coated carbon/carbon composites (SiC-C/C) was prepared by a novel hydrothermal electrophoretic deposition process. The phase composition, surface and cross-section microstructure of the as-prepared multi-layer coatings were characterized by X-ray Diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The influence of deposition voltage on phase composition, microstructure and oxidation resistance of the as-prepared coatings was particularly investigated. Results show that the outer layer coating mainly composed of C-AlPO₄ and mullite phase can be achieved after the hydrothermal electrophoretic deposition. The thickness, density and anti-oxidation property of the C-AlPO₄–mullite coating was improved with the increase of deposition voltage from 160 V to 200 V. The multi-layer coating prepared at a voltage of 200 V exhibit excellent anti-oxidation property, which can effectively protect C/C composites from oxidation in air at 1773 K for 324 h with a weight loss of 1.01%. The failure of the multi-layer coatings is due to the generation of cross-holes in the coating, which cannot be self-cured by the metaphosphate and silicate glass layer after long time oxidation at 1773 K.     

Design of an inlaid interface structure to improve the oxidation protective ability of SiC–MoSi2–ZrB2 coating for C/C composites

To improve the oxidation protective ability of SiC–MoSi₂–ZrB₂ coating for carbon/carbon (C/C) composites, pre-oxidation treatment and pack cementation were applied to construct a buffer interface layer between C/C substrate and SiC–MoSi₂–ZrB₂ coating. The tensile strength increased from 2.29 to 3.35 MPa after pre-oxidation treatment, and the mass loss was only 1.91% after oxidation at 1500 °C for 30 h. Compared with the coated C/C composites without pre-oxidation treatment, after 18 thermal cycles from 1500 °C and room temperature, the mass loss was decreased by 30.6%. The improvements of oxidation resistance and mechanical property are primarily attributed to the formation of inlaid interface between the C/C substrate and SiC–MoSi₂–ZrB₂ coating.     

Microstructure and ablation behavior of SiC coated C/C–SiC–ZrC composites prepared by a hybrid infiltration process

In this study, C/C–SiC–ZrC composites coated with SiC were prepared by precursor infiltration pyrolysis combined with reactive melt infiltration. The pyrolysis behavior of the hybrid precursor was investigated using thermal gravimetric analysis-differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy techniques. The microstructure and ablation behavior of the composites were also investigated. The results indicate that the composites exhibit an interesting structure, wherein a ceramic coating composed of SiC and a small quantity of ZrC covers the exterior of the composites, and the SiC–ZrC hybrid ceramics are partially embedded in the matrix pores and distributed around the carbon fibers as well. The composites exhibit good ablation resistance with a surface temperature of over 2300 °C during ablation. After ablation for 120 s, the mass and linear ablation rates of the composites are 0.0026 g/s and 0.0037 mm/s, respectively. The great ablation resistance of the composites is attributed to the formation of a continuous phase of molten SiO₂ containing SiC and ZrO₂, which seals the pores of the composites during ablation.     

A microstructural study of carbon–carbon composites impregnated with SiC filaments

Porous multidirectional carbon/carbon composite obtained by pulse chemical vapour infiltration (PCVI) was impregnated with silicon carbide (SiC) derived from pyrolysis of polymethylsiloxane resin (PMS). The impregnation process was made to improve oxidation resistance and mechanical properties of MD C/C composite. The resin was used as a source of silicon carbide component of the composite forming after heat treatment above 1000 °C. During this process SiC thin filaments were formed inside the porous carbon phase. The aim of this work was to investigate the structure and microstructure of the constituents of carbon composite obtained after pyrolysis of SiC PMS precursor. Microscopic observations revealed that during careful heat treatment of crosslinked polymethylsiloxane resin up to 1700 °C, the filaments (diameter 200–400 nm) crystallized within porous carbon phase. The filaments were randomly oriented on the composite surface and inside the pores. FTIR spectra and XRD analysis of the modified C/C composite showed that filaments had silicon carbide structure with the crystallite size of silicon carbide phase of about 45 nm. The Raman spectra revealed that the composite contains two carbon components distinctly differing in their structural order, and SiC filaments present nanocrystalline structure.     

Toughened carbon nanotube–iron–mullite composites prepared by spark plasma sintering

Carbon nanotube–iron–mullite nanocomposite powders were prepared by a direct method involving a reduction in H₂–CH₄ and without any mechanical mixing step. The carbon nanotubes are mostly double- and few-walled (3–6 walls). Some carbon nanofibers are also observed. The materials were consolidated by spark plasma sintering. Their electrical conductivity is 2.4 S/cm whereas pure mullite is insulating. There is no increase in fracture strength, but the SENB toughness is twice than the one for unreinforced mullite (3.3 vs. 1.6 MPa m^1/2). The mechanisms of carbon nanotube bundle pullout and large-scale crack-bridging have been evidenced.     

The high temperature oxidation and thermal shock behavior of a dense WSi2–TaSi2 coating on Ta substrate prepared by a novel two-step process

In order to improve the oxidation resistance of the Ta substrate, a novel two-step process including molten salt electrodeposition (Na₂WO₄-WO₃ system) and halide activated pack cementation was adopted to prepare a WSi₂–TaSi₂ coating on tantalum substrate. During the electrodeposition process, dense tungsten coatings were fabricated at current densities of 30 mA/cm², 40 mA/cm² and 50 mA/cm². It was observed that the grain size exhibited a log-normal distribution. When the current density was 40 mA/cm², the grain size and flattest surface of the tungsten coating reached 9.50 ± 0.23 μm and 6.792 μm, respectively. When performing the static oxidation test, the WSi₂–TaSi₂ coating could effectively protect the Ta substrate oxidized at 1600 °C for 30 h. This is attributed to the presence of dense SiO₂ and Ta₂O₅, which acted as a protective layer and suppressed the further penetration of oxygen. Furthermore, due to the matching thermal expansion coefficient between each layer and the sealing ability of semi-molten SiO₂, the four-layer SiO₂–W₅Si₃–WSi₂–Ta₅Si₃ coating could successfully pass 721 thermal shock tests from 1600 °C to room temperature.     

C/C–SiC composite prepared by Si–10Zr alloyed melt infiltration

A high performance and low cost C/C–SiC composite was prepared by Si–10Zr alloyed melt infiltration. Carbon fiber felt was firstly densified by pyrolytic carbon using chemical vapor infiltration to obtain a porous C/C preform. The eutectic Si–Zr alloyed melt (Zr: 10 at.%, Si: 90 at.%) was then infiltrated into the porous preform at 1450 °C to prepare the C/C–SiC composite. Due to the in situ reaction between the pyrolytic carbon and the Si–Zr alloy, SiC, ZrSi₂ and ZrC phases were formed, the formation and distribution of which were investigated by thermodynamics. The as-received C/C–SiC composite, with the flexural strength of 353.6 MPa, displayed a pseudo-ductile fracture behavior. Compared with the C/C preform and C/C composite of high density, the C/C–SiC composite presented improved oxidation resistance, which lost 36.5% of its weight whereas the C/C preform lost all its weight and the high density C/C composite lost 84% of its weight after 20 min oxidation in air at 1400 °C. ZrO₂, ZrSiO₄ and SiO₂ were formed on the surface of the C/C–SiC composite, which effectively protected the composite from oxidation.     

High-temperature erosion resistance and aerodynamic oxidation mechanism of multi-layer MoSi2–CrSi2–Si/SiC coated carbon/carbon composites in a wind tunnel at 1873 K

The high-temperature erosion resistance of multi-layer MoSi₂–CrSi₂–Si/SiC coated carbon/carbon (C/C) composites was investigated in a wind tunnel. To study the aerodynamic oxidation mechanism and analyze the failure of the coated C/C composites, the shear force and bending moment distribution of the tested specimens in a wind tunnel were calculated. Flexural strengths and thermogravimetric analysis of the coated specimens were measured. These results show that the multi-layer MoSi₂–CrSi₂–Si/SiC antioxidation coating can protect the C/C composites from high-temperature erosion in a wind tunnel at 1873 K for more than 86 h. Due to the high viscosity of SiO₂, the multi-layer coating lacked effective oxidation resistance from 900 to 1500 K, resulting in extensive mechanical damage and the fracture of the tested specimens.     

Microstructure and oxidation behavior of a novel bilayer (c-AlPO4–SiCw–mullite)/SiC coating for carbon fiber reinforced CMCs

A novel cristobalite aluminum phosphate particle (c-AlPO₄) modified SiC whisker toughened mullite coating (c-AlPO₄-SiC_w-mullite) was prepared on SiC coated carbon fiber reinforced SiC composites (C/SiC) by a new sol-gel method combined with air spraying to improve the oxidation resistance of SiC_w-mullite coating. Results show that c-AlPO₄-SiC_w-mullite coatings with 10 and 20 wt.% of c-AlPO₄ exhibited obviously improved oxidation resistance at 1773 K in ambient air for 100 h than SiC_w-mullite coating. Moreover, the oxidation resistance of c-AlPO₄-SiC_w-mullite coatings were rapidly declined when the c-AlPO₄ in c-AlPO₄-SiC_w-mullite coating were set to 30 and 40 wt.%. The c-AlPO₄-SiC_w-mullite coating with 20 wt.% of c-AlPO₄ showed most pronounced oxidation resistance, the weight loss rate after the oxidation in ambient air for 210 h was merely 3.00 × 10^?5 g·cm^?2 h^?1. The failure of c-AlPO₄-SiC_w-mullite coating with 20 wt.% of c-AlPO₄ was due to the generation of penetrative micro-cracks and micro-holes in the coating, which cannot be self-healed by the silicate glass layer after long time oxidation at 1773 K.