Positive temperature coefficient to resistively characteristics of polystyrene/nickel powder/multiwall carbon nanotubes composites

Positive temperature coefficient to resistivity (PTCR) characteristics of polystyrene (PS)/Ni‐powder (40 wt%) composites in the presence of multiwall carbon nanotubes (MWCNTs) has been investigated with reference to PS/carbon black (CB) composites. The PS/CB (10 wt%) composites showed a sudden rise in resistivity (PTC trip) at ≈110°C, above the glass transition temperature (T_g) of PS (T_g ≈95°C). Interestingly, the PTC trip temperature of PS/Ni‐powder (40 wt%)/MWCNT (0.75 phr) composites appeared at ≈90°C (below T_g of PS), indicating better dimensional stability of the composites at PTC trip temperature. The PTC trip temperature of the composites below the T_g of matrix polymer (PS) has been explained in terms of higher coefficient of thermal expansion (CTE) value of PS than Ni that led to a disruption in continuous network structure of Ni even below the T_g of PS. The dielectric study of PS/Ni‐powder (40 wt%)/MWCNT (0.75 phr) composites indicated possible use of the PTC composites as dielectric material. Dynamic mechanical analysis (DMA) and thermogravimetric analysis studies revealed higher storage modulus and improved thermal stability of PS/Ni‐powder (40 wt%)/MWCNT (0.75 phr) composites than the PS/CB (10 wt%) composites. POLYM. COMPOS., 33:1977–1986, 2012. © 2012 Society of Plastics Engineers     

Montmorillonite nanoclay filler effects on electrical conductivity,thermal and mechanical properties of epoxy‐based nanocomposites

Epoxy‐based nanocomposites with 2, 5, and 7 wt% of montmorillonite (MMT) nanoclay were prepared using high shear melt mixing technique. The microstructural features of the nanocomposites were investigated by transmission electron microscopy (TEM). The thermal and mechanical properties were measured using differential scanning calorimetry (DSC), thermogravimetric analyzer (TGA), and dynamic mechanical analyzer (DMA). Further, the effect of voltage, temperature, seawater aging on the electrical conductivity (σ_DC) of the nanocomposites was also measured. To understand the free volume behavior upon filler loading, and to observe the connectivity between microstructure and other properties, positron annihilation lifetime spectroscopy was used. The TEM results revealed that MMT nanoparticles were uniformly dispersed in the epoxy matrix. Experimental results showed that the inclusion of 2 wt% MMT nanofiller increased the T_g, electrical conductivity, thermal stability, modulus, free volume of the epoxy nanocomposite significantly. This is well explained from the results of T_g (DSC and DMA), thermal stability, TGA residue, free volume analysis, and electrical conductivity. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Preparation and properties of multiwalled carbon nanotube/epoxy‐amine composites

Different amounts of multiwalled carbon tubes (MWCNTs) were incorporated into an epoxy resin based on diglycidyl ether of bisphenol A and both epoxy precursor and composite were cured with 4,4′‐diamino diphenyl sulfone. Transmission and scanning electron microscopy demonstrated that the carbon nanotubes are dispersed well in the epoxy matrix. Differential scanning calorimetry measurements confirmed the decrease in overall cure by the addition of MWCNTs. A decrease in volume shrinkage of the epoxy matrix caused by the addition of MWCNTs was observed by pressure–volume–temperature measurements. Thermomechanical and dynamic mechanical analysis were performed for the MWCNT/epoxy composites, showing that the T_g was slightly affected, whereas the dimensional stability and stiffness are improved by the addition of MWCNTs. Electrical conductivity measurements of the composite samples showed that an insulator to conductor transition takes place between 0.019 and 0.037 wt % MWCNTs. The addition of MWCNTs induces an increase in both impact strength (18%) and fracture toughness (38%) of the epoxy matrix with very low filler content. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Direct functionalization with 3,5‐substituted benzoic acids of multiwalled carbon nanotube/epoxy composites

Directly functionalized multiwalled carbon nanotubes (MWCNTs) with benzene‐1,3,5‐tricarboxylic acid (BTC) and 3,5‐diaminobenzoic acid (DAB) were successfully accomplished with less structural damage as confirmed by XPS and FT‐Raman results. Their dispersibility and thermal stability were achieved after the functionalization. The functional groups on MWCNT surfaces can accelerate the curing reaction of epoxy composites remarkable inducing rather low exothermic peak temperature (T_p) and exothermic heat of reaction (ΔH). The values of activation energy (E_a) obtained from Kissinger and Ozawa methods obviously decreased with the introduction of MWCNTs, especially DAB‐MWCNTs. The dynamic mechanical properties notably enhanced with the incorporation of unmodified and functionalized MWCNTs. The crosslink density (ρ) increased and free volume fraction (f_g) decreased, resulting in dramatic increase of glass transition temperatures (T_g) and decrease of coefficient of thermal expansion. Additionally, epoxy composites exhibited low dielectric constant close to that of neat epoxy resin. From these remarkable properties, MWCNT/epoxy composites can be considered as a good candidate for high performance insulation materials. POLYM. ENG. SCI., 53:2194–2204, 2013. © 2013 Society of Plastics Engineers     

Functionalized graphene sheets‐epoxy based nanocomposite for cryotank composite application

Multifunctional high performance functionalized graphene sheets (FGSs) based epoxy nanocomposites were investigated to understand the feasibility that these FGSs‐epoxy nanocomposites can be applied to cryotank composite applications. The FGSs were successfully synthesized from graphite flakes through preparing graphite oxides by oxidizing graphite flakes first and next, thermally exfoliating the formed graphite oxides. These high performance FGSs were next incorporated into epoxy matrix resin system to generate the uniformly dispersed FGSs reinforced epoxy nanocomposites. The resultant FGSs‐epoxy nanocomposites significantly enhanced resin strength and toughness about 30–80% and 200–700% at room and low temperatures of −130°C, respectively, and reduced the coefficient of thermal expansion (CTE) of polymer resin at both below and above T_g about 25% at loading of 1.6 wt% FGSs, and increased T_g of polymer resin about 8°C at low loading of 0.4 wt% FGSs without deteriorating their good processability. We found that these significantly improved properties of FGSs‐reinforced epoxy nanocomposite were closely associated with high surface area and wrinkled structure of the FGSs. The further optimization will result the high performance FGSs‐epoxy nanocomposite suitable for use in the next generation multifunctional cryotank carbon fiber reinforced polymer (CFRP) composite applications, where better microcrack resistance and mechanical and dimensional stability are needed. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Poly(N‐vinyl carbazole) (PNVCz)‐based composite materials: Electrical properties,morphologic, and thermal characterization of PNVCz/MWCNTs and PNVCz/o‐GLs systems

Poly(N‐vinylcarbazole)/oxidized‐graphite layers (PNVCz/o‐GLs) and PNVCz/multiwalled carbon nanotubes (MWCNTs) composites were prepared by both solution blending and in situ polymerization methods. Fourier transform infrared spectroscopy (FTIR), X‐ray diffractometer (XRD), and polarized optical microscope (POM) were used for their structural and morphologic characterization. Thermal stabilities and glass transition temperatures (T_gs) were measured by thermogravimetry (TG) and differential scanning calorimetry (DSC), respectively. The synthesis and characterization results showed that the in situ polymerization of NVCz could be initiated without cerium ammonium nitrate, CAN as oxidant in the presence of the o‐GLs and o‐MWCNTs dispersed and activated by sonication in acetonitrile (ACN)/sodium dodecyl sulfate (SDS)/water mixture and in ACN, respectively. It was discussed that the PNVCz chains were interacted with the conducting surfaces of fillers by hydrogen bonds and/or by coating, depending on the synthesis conditions, preparation process and the structure of organic matrix. Further, the electrical conductivity of PNVCz was improved from insulating to semiconducting state in the presence of both o‐GLs and MWCNTs. POLYM. COMPOS., 34:1986–1998, 2013. © 2013 Society of Plastics Engineers     

Properties of a reactive‐graphitic‐carbon‐nanofibers‐reinforced epoxy

Our previous studies showed that herringbone graphitic GNFs surface‐derivatized with reactive linker molecules bearing pendant primary amino functional groups capable of binding covalently to epoxy resins. Of special importance, herringbone GNFs derivatized with 3,4′‐oxydianiline (GNF‐ODA) were found to react with neat butyl glycidyl ether to form mono‐, di‐, tri‐, and tetra‐glycidyl oligomers covalently coupled to the ODA pendant amino group. The resulting reactive GNF‐ODA (butyl glycidyl)_n nanofibers, r‐GNF‐ODA, are especially well suited for reactive, covalent incorporation into epoxy resins during thermal curing. Based on these studies, nanocomposites reinforced by the r‐GNF‐ODA nanofibers at nanofiber loadings of 0.15–1.3 wt% were prepared. Flexural property of cured r‐GNF‐ODA/epoxy nanocomposites were measured through three‐point‐bending tests. Thermal properties, including glass transition temperature (T_g) and coefficient of thermal expansion (CTE) for the nanocomposites, were investigated using thermal mechanical analysis. The nanocomposites containing 0.3 wt% of the nanofibers gives the highest mechanical properties. At this 0.3‐wt% fiber loading, the flexural strength, modulus and breaking strain of the particular nanocomposite are increased by about 26, 20, and 30%, respectively, compared to that of pure epoxy matrix. Moreover, the T_g value is the highest for this nanocomposite, 14°C higher than that of pure epoxy. The almost constant change in CTEs before and after T_g, and very close to the change of pure epoxy, is in agreement with our previous study results on a chemical bond existing between the r‐GNF‐ODA nanofibers and epoxy resin in the resulting nanocomposites. POLYM. COMPOS., 28:605–611, 2007. © 2007 Society of Plastics Engineers     

Novel flame retardant thermosets from nitrogen‐containing and phosphorus‐containing epoxy resins cured with dicyandiamide

A novel phosphorus‐containing epoxy resin (EPN‐D) was prepared by addition reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide (DOPO) and epoxy phenol‐ formaldehyde novolac resin (EPN). The reaction was monitored by epoxide equivalent weight (EEW) titration, and its structure was confirmed by FTIR and NMR spectra. Halogen‐free epoxy resins containing EPN‐D resin and a nitrogen‐containing epoxy resin (XT resin) were cured with dicyandiamide (DICY) to give new halogen‐free epoxy thermosets. Thermal properties of these thermosets were studied by differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), thermal mechanical analyzer (TMA) and thermal‐gravimetric analysis (TGA). They exhibited very high glass transition temperatures (T_gs, 139–175°C from DSC, 138–155°C from TMA and 159–193°C from DMA), high thermal stability with T_{d,5 wt %} over 300°C when the weight ratio of XT/EPN‐D is ≥1. The flame‐retardancy of these thermosets was evaluated by limiting oxygen index (LOI) and UL‐94 vertical test. The thermosets containing isocyanurate and DOPO moieties showed high LOI (32.7–43.7) and could achieve UL‐94 V‐0/V‐1 grade. Isocyanurate and DOPO moieties had an obvious synergistic effect on the improvement of the flame retardancy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Curing of epoxy systems at sub‐glass transition temperature

Three epoxy‐amine thermoset systems were cured at a low ambient temperature. Evolution of the reaction kinetics and molecular structure during cure at the sub‐glass transition temperature was followed by DSC and chemorheology experiments. The effect of vitrification and the reaction exotherm on curing and final mechanical properties of the epoxy thermosets was determined. Thermomechanical properties of the low‐temperature cured systems depend on the reaction kinetics and volume of the reaction mixture. Curing of the fast‐reacting system in a large volume (12‐mm thick layer) resulted in the material with T_g exceeding the cure temperature by 70–80°C because of an exothermal temperature rise. However, the reaction in a too large volume (50‐mm layer) led to thermal degradation of the network. In contrast, thin layers (1.5 mm) were severely undercured. Well‐cured epoxy thermosets could be prepared at sub‐T_g temperatures by optimizing reaction conditions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3669–3676, 2006     

Synthesis and characterization of multiwalled carbon nanotube/polyurethane composites via surface modification multiwalled carbon nanotubes using silane coupling agent

Well‐dispersed multiwalled carbon nanotubes/polyurethane (MWCNTs/PU) composites were synthesized in situ polymerization based on treating MWCNTs with nitric acid and silane coupling agent. The morphology and degree of dispersion of the MWCNTs were studied using a high resolution transmission electron microscopy (HR‐TEM) and X‐ray powder diffraction (XRD). The result showed that MWCNTs could be dispersed still in the PU matrix well with the addition of 2 wt% MWCNTs. The thermal and mechanical properties of the composites were characterized by dynamic mechanical thermal analysis, thermogravimetric analysis, tensile, and impact testing. The result suggested that the glass transition temperature (T_g) of composites increased greatly with increasing MWCNTs content slightly, and the MWCNTs is also helpful to improve mechanical properties of composites. Furthermore, the composites have an excellent mechanical property with the addition of 0.5 wt% MWCNTs. The electrical property testing indicates that the MWCNTs can improve evidently the electrical properties of composites when adding 1 wt% MWCNTs to the PU matrix. The volume resistivity of composites reaches to an equilibrium value. POLYM. COMPOS., 33:1866–1873, 2012. © 2012 Society of Plastics Engineers     

Effect of cobalt on the electrical conductive property of epoxy resins

Cobalt acrylate (CoA₂) has been treated with bisphenol‐A and epichlorohydrin to modify epoxy resins. It was cured with p‐acetylbenzilidene triphenyl arsonium ylide. The properties such as epoxide equivalent weight (equiv/100 g), molecular weight, hydrolyzable chlorine content increases whereas hydroxyl content, refractive index decreases in the presence of CoA₂. The cured epoxy resins shows improve electrical conductivity due to the incorporation of CoA₂ with epoxy resins. The influence of complex formation of CoA₂ with either linkage of epoxy resins were investigated by spectroscopy. The decrease in T_g from differential scanning calorimetry support the improve in flexibility. The dispersion of cobalt in epoxy resins matrix was confirmed by scanning electron microscope. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of Al2O3 addition on thermo‐electrical properties of polymer composites: An experimental investigation

To develop a new class of composites with adequately high thermal conductivity and suitably controlled dielectric constant for electronic packages and printed circuit board applications, polymer composites are prepared with microsized Al₂O₃ particle as filler having an average particle size of 80–100 μm. Epoxy and polypropylene (PP) are chosen as matrix materials for this study. Fabrication of epoxy‐based composite is done by hand lay‐up technique and its counterpart PP‐based composite are fabricated by compression molding technique with filler content ranging from 2.5–25 vol%. Effects of filler loading on various thermal properties like effective thermal conductivity (k_eff), glass transition temperature (T_g), coefficient of thermal expansion (CTE) and electrical property like dielectric constant (ε_c) of composites are investigated experimentally. In addition, physical properties like density and void fraction of the composites along with there morphological features are also studied. The experimental findings obtained under controlled laboratory conditions are interpreted using appropriate theoretical models. Results show that with addition of 25 vol% of Al₂O₃, k_eff of epoxy and PP improve by 482% and 498% respectively, T_g of epoxy increases from 98°C to 116°C and that of PP increases from −14.9°C to 3.4°C. For maximum filler loading of 25 vol% the CTE decreases by 14.8% and 26.4% for epoxy and PP respectively whereas the dielectric constants of the composites get suitably controlled simultaneously. POLYM. COMPOS., 36:102–112, 2015. © 2014 Society of Plastics Engineers     

Electrically conducting polypropylene/polyaniline‐grafted‐short glass fiber composites: Microstructure and dynamic mechanical analysis

The thermal properties of isotactic polypropylene (iPP) reinforced with polyaniline‐grafted‐short glass fibers (PAn‐g‐SGF) at 10, 20, and 30 wt% concentration and iPP blended with 5 wt% PP‐grafted‐maleic anhydride (PP‐gMA) and 30 wt% of PAn‐g‐SGF were investigated. iPP crystallizes into a spherulitic morphology, the microfiller promoted larger spherulite size and higher dynamic modulus, but the overall degree of crystallinity decreased as the concentration of PAn‐g‐SGF increased. The melting temperature, T_m, was not influenced by the microfiller. However, the crystallization temperature, T_c, as determined by DMA, first decreased reaching a minimum at ca. 20 wt%, and then increased, in contrast with T_c determined by DSC, it increased as concentration increased. The initial reduction in T_c observed by DMA seems to be associated with the crystallites growing from the microfiller into the matrix, the overall molecular dynamics then being less affected. On the other hand, increase in T_c above 20 wt% concentration suggests that the percolation threshold could be responsible for these results. Addition of the maleic anhydride copolymer produced higher shear modulus, transition temperatures, and activation energy, suggesting higher interaction between microfiller and polymer matrix. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Significantly Strengthening Epoxy by Incorporating Carbon Nanotubes/Graphitic Carbon Nitride Hybrid Nanofillers

Novel hybrid nanofillers consist of carbon nanotubes (CNTs) and graphitic carbon nitride (g‐C₃N₄) are prepared for the enhanced mechanical properties of epoxy by improving the dispersion of CNTs. 2D planar structure, large surface area, and plentiful of surface reactive groups of g‐C₃N₄ efficiently resist the microcrack propagation, impede the thermal transfer, and provide chemical bonding with epoxy chains. The well‐dispersed CNTs by anchoring on g‐C₃N₄ surface promotes the efficient transfers of stress, and supply the stronger mechanical interlocking for interfacial bonding. The significantly enhanced mechanical properties of epoxy containing hybrid nanofillers are based on the synergistic effects between CNTs and g‐C₃N₄. Compared with neat epoxy, the tensile strength, tensile modulus, and storage modulus of epoxy containing 0.5 wt% hybrid nanofillers (CNTs: g‐C₃N₄ = 1: 9, w/w) below glass transition temperature (T_g) are increased by 37.65%, 29.36%, and 32.92%, respectively. Meanwhile, the T_g, onset decomposition temperature and char residue are also obviously raised.     

Surfactant-Assisted Dispersion of MWCNTs in Epoxy Resin Used in CFRP Strengthening Systems

The epoxy resin used as the bonding agent in carbon fiber-reinforced polymer (CFRP) strengthening systems was modified by the infusion of multiwalled carbon nanotubes (MWCNTs). Two types of surfactants, Triton X-100 and C₁₂E₈, were used to disperse the nanotubes in the epoxy resin employing ultrasonic mixing. Dynamic mechanical analysis and tensile tests were conducted to study the effect of the surfactant-assisted dispersion of nanotubes on the thermal and mechanical properties of epoxy composites. The morphology of the epoxy composites was interpreted using scanning electron microscopy (SEM). Moreover, the effect of surfactant treatment on the structure of nanotubes was investigated by Fourier transform infrared (FT-IR). Based on the experimental results, the tensile strength and the storage modulus of the epoxy resin were increased by 32% and 26%, respectively, by the addition of MWCNTs. This was attributed to the homogeneous dispersion of nanotubes in the epoxy resin according to the SEM images. Another reason for the enhancement in the tensile properties was the reinforced nanotube/epoxy interaction as a result of the surfactant anchoring effect which was proved by FT-IR. A moderate improvement in the glass transition temperature (T _g) was recorded for the composite fabricated using Triton X-100, which was due to the restricted molecular motions in the epoxy matrix. To characterize the temperature-dependent tensile behavior of the modified epoxy composites, tensile tests were conducted at elevated temperatures. It was revealed that the MWCNT modification using surfactant substantially improves the tensile performance of the epoxy adhesive at temperatures above the T _g of the neat epoxy.     

Synthesis and characterization of (Fe3O4/MWCNTs)/ epoxy nanocomposites

A sonochemical technique is used for in situ coating of iron oxide (Fe₃O₄) nanoparticles on outer surface of MWCNTs. These Fe₃O₄/MWCNTs were characterized using a high‐resolution transmission electron microscope (HRTEM), X‐ray diffraction, and thermogravimetric analysis. The as‐prepared Fe₃O₄/MWCNTs composite nanoparticles were further used as reinforcing fillers in epoxy‐based resin (Epon‐828). The nanocomposites of epoxy were prepared by infusion of (0.5 and 1.0 wt %) pristine MWCNTs and Fe₃O₄/MWCNTs composite nanoparticles. For comparison purposes, the neat epoxy resin was also prepared in the same procedure as the nanocomposites, only without nanoparticles. The thermal, mechanical, and morphological tests were carried out for neat and nanocomposites. The compression test results show that the highest improvements in compressive modulus (38%) and strength (8%) were observed for 0.5 wt % loading of Fe₃O₄/MWCNTs. HRTEM results show the uniform dispersion of Fe₃O₄/MWCNTs nanoparticles in epoxy when compared with the dispersion of MWCNTs. These Fe₃O₄/MWCNTs nanoparticles‐infused epoxy nanocomposite shows an increase in glass transition (T_g) temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal and thermomechanical behavior of amino functionalized and metal decorated MWCNTs/PMMA nanocomposite films

The homogeneous nanocomposites (NC) films of amino modified and metal decorated multiwall carbon nanotubes (MWCNTs) with polymethylmethacrylate (PMMA) were synthesized through in‐situ free radical polymerization. Silver metal nanohybrids (Ag/MWCNTs) were prepared by two strategies, that is, reduction of metal salt in presence of sodium dodecyl sulfate and in‐situ growth from AgNO₃ aqueous solution. The amino functionalization by ball milling enhanced the dispersion of MWCNT in monomer and produced a new class of radiation resistant NC. These synthesized films were characterized by FTIR, TGA, TEM, EDX, TC, DMA, and optical microscopy to ascertain their structural morphologies, thermal stability, and mechanical strength. Microscopic studies reflect the homogeneous mixing of amino functionalized and metal decorated MWCNTs in polymer matrix contributing in the enhancement of thermal stability, thermo‐mechanical strength, glass transition temperatures, and thermal conductivity of NC even at 0.25 wt% addition of modified nanofiller. The thermal stability of NC film at 0.25 wt% loading was increased around ≂50°C and the raise of thermo‐mechanical properties was observed up to 85% at 100°C in the presence of adsorbed surfactant. Thermal and thermomechanical behavior of pre and post UV/O₃ irradiated NC films has been compared with neat polymer. The results revealed that amino modified nanofiller embedded network in polymer matrix can effectively disperse the radiation and has a dramatic reinforcement effect on the nature of degradation of PMMA matrix. POLYM. COMPOS., 35:1807–1817, 2014. © 2013 Society of Plastics Engineers     

Supercritical carbon dioxide-assisted silanization of multi-walled carbon nanotubes and their effect on the thermo-mechanical properties of epoxy nanocomposites

Supercritical carbon dioxide was employed as the solvent for the functionalization of multi-walled carbon nanotubes (MWCNTs) with an epoxy-capped silane. The silanization protocol was found to be a suitable green alternative to traditional routes that rely on organic solvents for grafting nearly monolayers of silane molecules onto the nanotube surfaces. The addition of silanized MWCNTs to a model epoxy markedly increased its T_g, and measurements of the network cooperativity length scale linked this change to a reduction in polymer segment mobility. Composites filled with low loading levels of both pristine and silanized MWCNTs exhibited significantly higher strain at break and toughness than the neat epoxy, and the greatest improvements were observed at low loading levels. SEM analysis of the composite fracture surfaces revealed that nanotube pullout was the primary failure mechanism in epoxy loaded with pristine MWCNTs while crack bridging predominated in composites containing silanized MWCNTs as the result of strong interfacial bonding with the matrix. The elevated T_g and toughness achieved with small additions of silanized MWCNTs promise to extend the engineering applications of the epoxy resin.     

Effect of Dodecyal Amine Functionalized Graphene on the Mechanical and Thermal Properties of Epoxy‐Based Composites

Simultaneous surface functionalization and reduction of graphene oxide (GO) was achieved by using dodecyl amine (DA) as surface modifying agent. The DA modified reduced GO (DA‐G) was used for subsequent preparation of DA‐G/epoxy composites by solution mixing. Fourier transform infrared spectroscopy analysis, X‐ray diffraction (XRD) and electrical conductivity measurements were conducted to establish the concurrent functionalization and reduction of GO. The effect of DA‐G on the epoxy composites at 0 to 0.75 wt% loadings was studied by investigating its static and dynamical mechanical properties. XRD study was performed to verify the dispersion of DA‐G in the epoxy polymer. Field emission scanning electron microscopy was used to investigate the fracture surface morphology of the composites and Transmission electron microscopy was employed to further confirm the dispersion of DA‐G in the matrix. It was found that the tensile strength of the composite was increased by 38.8% with the addition of 0.5 wt% of DA‐G. The good adhesion/interaction between DA‐G and epoxy resulted in the increase of storage modulus; however, glass transition temperature (T_g) value of the composites shifted to lower temperature in comparison to the neat epoxy. Thermogravimetric analysis showed small decrease in onset degradation temperature for the composites as compared to neat epoxy except for the composites containing 0.75 wt% of DA‐G. POLYM. ENG. SCI., 56:1221–1228, 2016. © 2016 Society of Plastics Engineers     

Effect of nanodiamonds and multi-walled carbon nanotubes in thermoset hybrid fillers system: Rheology,dynamic mechanical analysis,and thermal stability

Recently, the interfacial bonding between nanodiamonds (DNDs) and multi-walled carbon nanotubes (MWCNTs) in epoxy-based nanocomposites were found. In this work, effects of amino functionalization on MWCNTs and DNDs introduction on rheology, dynamic mechanical properties, and thermal stability of MWCNTs epoxy-based nanocomposites are discussed. The results show that pristine MWCNTs increase the complex viscosity, lower the molecular weight of epoxy net chains as well as glass transition temperature (T_g), and expand the phase separation. Amino functionalization of MWCNTs make the behaviors above disappeared nearly. Besides, introduction DNDs improved T_g and restricted the phase separation as well, but the high complex viscosity and non-Newtonian behavior remains. This work may provide inspirations for the further researches about hybrid fillers.