Highly methanol resistant and selective ternary blend membrane composed of sulfonated PVdF‐co‐HFP,sulfonated polyaniline and nafion

Partially sulfonated poly(vinylidene fluoride‐co‐hexafluoro propylene)/partially sulfonated polyaniline (SPVdF‐co‐HFP/SPAni) binary blend membranes have shown promising results in terms of low methanol permeability and high membrane selectivity compared to Nafion‐117 membrane. However, the proton conductivity and IEC of this binary blend membrane was much lower than Nafion‐117. It was found that incorporation of minimal quantity of Nafion within SPVdF‐co‐HFP/SPAni blend membrane at a constituent weight % ratio of SPVdF‐co‐HFP:SPAni:Nafion = 50:40:10 induced significant improvements in ion‐exchange capacity (IEC), proton conductivity and tensile strength over that of the binary blend membrane. In addition, the SPVdF‐co‐HFP/SPAni/Nafion ternary blend membrane exhibited much lower methanol permeability, higher membrane and relative selectivities and comparable IEC to Nafion‐117. In effect, presence of minimal quantity of Nafion induced significant positive attributes to the ternary blend membrane; and assisted in reaching a balance between material cost and properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43294.     

Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Sulfonated (graphene oxide/poly(ether ketone ether sulfone) (S-GO/S-PEKES) composite proton exchange membrane with high proton conductivity for direct methanol fuel cell

ABSTRACT

Sulfonated poly(ether ketone ether sulfone) (S-PEKES) was successfully prepared to obtain the currently highest degree of sulfonation of 0.744. Sulfonated graphene oxide (S-GO) was incorporated into the S-PEKES matrix to increase sulfonic groups (SO₃H) which significantly improved the proton conductivity, methanol blocking, and mechanical stability. The proton conductivity of the S-GO/S-PEKES composite membrane was enhanced up to 5.93 × 10^?2 S.cm^?1, which was 7 times higher than the commercial Nafion 117. S-GO exhibited additional positive effects namely the blocking of methanol passing through the membrane, leading to lower methanol crossover than Nafion 117 by two orders of magnitude and high mechanical stability.     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Synthesis and characterization of sulfonated poly(ether sulfone ether ketone ketone) for proton exchange membranes

A series of sulfonated poly(ether sulfone ether ketone ketone) (SPESEKK) with different degree of sulfonation (DS) are prepared by the postsulfonation of PESEKK using chlorosulfonic acid as sulfonating agent and concentrated sulfuric acid as solvent. The chemical structures of the polymers are analyzed by the proton nuclear magnetic resonance. The thermal properties of the SPESEKK show that they are greatly influenced by the DS value and sulfonation time. The water uptake, proton conductivity, and Ion exchange capacity values increase as the sulfonation time increasing. The methanol permeability of the SPESEKK in the range of 7.02 × 10^?8 to 4.477 × 10^?7 cm² s^?1, is one or two orders of magnitude lower than that of Nafion 115. The morphology of the SPESEKK membranes is investigated by scanning electron microscope. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

New organic–inorganic hybrid membranes based on sulfonated polyimide/aminopropyltriethoxysilane doping with sulfonated mesoporous silica for direct methanol fuel cells

A series of novel composite methanol‐blocking polymer electrolyte membranes based on sulfonated polyimide (SPI) and aminopropyltriethoxysilane (APTES) doping with sulfonated mesoporous silica (S‐mSiO₂) were prepared by the casting procedure. The microstructure and properties of the resulting hybrid membranes were extensively characterized. The crosslinking networks of amino silica phase together with sulfonated mesoporous silica improved the thermal stability of the hybrid membranes to a certain extent in the second decomposition temperature (250–400°C). The composite membranes doping with sulfonated mesoporous silica (SPI/APTES/S‐mSiO₂) displayed superior comprehensive performance to the SPI and SPI/APTES membranes, in which the homogeneously embedded S‐mSiO₂ provided new pathways for proton conduction, rendered more tortuous pathways as well as greater resistance for methanol crossover. The hybrid membrane with 3 wt % S‐mSiO₂ into SPI/APTES‐4 (SPI/A‐4) exhibited the methanol permeability of 4.68 × 10^?6 cm² s^?1at 25°C and proton conductivity of 0.184 S cm^?1 at 80°C and 100%RH, while SPI/A‐4 membrane had the methanol permeability of 5.16 × 10^?6 cm² s^?1 at 25°C and proton conductivity of 0.172 S cm^?1 at 80°C and 100%RH and Nafion 117 exhibited the values of 8.80 × 10^?6 cm² s^?1 and 0.176 S cm^?1 in the same test conditions, respectively. The hybrid membranes were stable up to about 80°C and demonstrated a higher ratio of proton conductivity to methanol permeability than that of Nafion117. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of poly(vinyl alcohol)‐based membranes for direct methanol fuel cell

Membranes made of poly(vinyl alcohol) (PVA) and its ionic blends with sodium alginate (SA) and chitosan were synthesized and characterized for their ion-exchange capacity (IEC) and swelling index values to investigate their applicability in direct methanol fuel cells (DMFCs). These membranes were assessed for their intermolecular interactions, thermal stabilities, and mechanical strengths with Fourier transform infrared spectroscopy, X-ray diffraction methods, differential scanning calorimetry, thermogravimetric analysis, and tensile testing, respectively. Methanol permeability and proton conductivity were also estimated and compared to that of Nafion 117. In addition to being effective methanol barriers, the membranes had a considerably high IEC and thermal and mechanical stabilities. The addition of small amounts of anionic polymer was particularly instrumental in the significant reduction of methanol permeability from 8.1 × 10⁻⁸ cm²/s for PVA to 6.9 × 10⁻⁸ cm²/s for the PVA–SA blend, which rendered the blend more suitable for a DMFC. Low methanol permeability, excellent physicomechanical properties, and above all, cost effectiveness could make the use of these blends in DMFCs quite attractive. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1154–1163, 2005     

Evaluation of Low‐Cost Separators for Increased Power Generation in Single Chamber Microbial Fuel Cells with Membrane Electrode Assembly

We compared novel size‐selective separators, namely the textile fabrics of polyphenylene sulfide (PPS) and sulfonated polyphenylene sulfide (S‐PPS), and the nonwoven fabrics of polypropylene80 (PP 80) and PP 100, with commonly used ion exchange separators (Nafion 117 and cation exchange membane‐7000; CMI‐7000) in terms of power generation, oxygen diffusion, and biofilm formation in a single chamber microbial fuel cell. Size‐selective separators exhibited more power generation than ion selective separators. MFC operation with size‐selective separators generated power output ranging 0.407 to 0.591 V (1000 Ω), whereas with Nafion it was 0.272 V. In polarization analysis, S‐PPS resulted in the highest power density of 190 mW/m², whereas it was 24 mW/m² with Nafion‐117. Size selective separators showed similar or higher proton conductivity than Nafion 117. Oxygen mass transfer coefficients of size‐selective separators (K_O = 3.7 ∼ 7.5 × 10⁻⁵) were lower or similar to Nafion (K_O = 7.5 × 10⁻⁵). Fourier‐transform infrared spectroscopy and scanning electron microscopy analysis revealed that all separators (PP80, S‐PPS, and Nafion) contained proteins or carbon chain compounds after 300‐day operation, and however, Nafion 117 seems to be more susceptible to biofouling than the other separators.     

Preparation and characterization of novel grafted cellophane‐phosphoric acid‐doped membranes for proton exchange membrane fuel‐cell applications

This work concerns preparation of acid‐base polyelectrolyte membranes for fuel‐cell applications from cellulosic backbones for the first time. Grafted cellophane‐phosphoric acid‐doped membranes for direct oxidation methanol fuel cells (DMFC) were prepared following three steps. The first two steps were conducted to have the basic polymers. The first step was introducing of epoxy groups to its chemical structure through grafting process with poly(glycidylmethacrylate) (PGMA). The second step was converting the introduced epoxy groups to imides groups followed by phosphoric acid (? PO₃H) doping as the last step. This step significantly contributes to induce ion exchange capacity (IEC) and ionic conductivity (IC). Chemical changes of the cellophane composition and morphology characters were followed using FTIR, TGA, and SEM analysis. Different factors affecting the membranes characters especially IEC, methanol permeability, and thermal stability were investigated and optimized to have the best preparation conditions. Compared to Nafion 117 membrane, cellophane‐modified membranes show a better IEC, less methanol permeability, and better mechanical and thermal stability. IEC in the range of 1–2.3 meq/g compared to 0.9 meq/g per Nafion was obtained, and methanol permeability has been reduced by one‐order magnitude. However, the maximum obtained IC for cellophane‐PGMA‐grafted membrane doped with phosphoric acid was found 2.33 × 10^?3 (S cm^?1) compared to 3.88 × 10^?2 (S cm^?1) for Nafion 117. The obtained results are very promising for conducting further investigations taking into consideration the very low price of cellophane compared to Nafion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of Sulfonated Graphene Oxide on Sulfonated Polysulfone Membrane for Direct Methanol Fuel Cell

Novel proton exchange membranes consisting of an inorganic filler, namely sulfonated graphene oxide, embedded in sulfonated polysulfone were fabricated. The membrane performance depended on the sulfonated graphene oxide content possessed the functional groups to provide the interfacial interaction with sulfonated polysulfone through ionic channels and blocking effect. The membrane with 3% v/v sulfonated graphene oxide content embedded in the matrix was shown to be suitable for direct methanol fuel cell applications. The membrane exhibited the highest proton conductivity of 4.27?×?10^?3 S cm^?1 which was higher than that of Nafion117. Moreover, the membrane provided the lowest methanol permeability of 3.48?×?10^?7?cm²/s which was lower than that of Nafion117.     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

New composite membrane poly(vinyl alcohol)/graphene oxide for direct ethanol–proton exchange membrane fuel cell

This study investigated a simple synthesis of a crosslinked poly(vinyl alcohol)/ graphene oxide composite membrane with lower ethanol permeability membrane for passive direct ethanol–proton exchange membrane fuel cells (DE-PEMFCs). The chemical and physical structure, morphologies, ethanol uptake and permeability, ion exchange capacities, water uptake, and proton conductivities were determined and found that transport properties of the membrane were affected by the GO loading. The composite membrane with optimum GO content (15 wt %) exhibited the highest proton conductivity of 9.5 × 10⁻³ Scm⁻¹ at 30°C, 3.24 × 10⁻² Scm⁻¹ at 60°C, respectively and reduced ethanol permeability until 1.75 × 10⁻⁷ cm² s⁻¹. In the passive DE-PEMFC, the power density at 60°C were obtained as 5.84 mW cm⁻² higher than those by commercial Nafion 117 is 4.52 mW cm⁻². © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46928.     

Improved chemical stability and proton selectivity of semi-interpenetrating polymer network amphoteric membrane for vanadium redox flow battery application

In this work, semiinterpenetrating polymer network (semi-IPN), consisting of sulfonated poly (arylene ether sulfone) (SPAES) and crosslinked vinyl imidazole grafted polysulfone (VMPSU), is prepared and characterized. FTIR, EDS, and solubility test indicate the successful preparation of amphoteric membranes. The semi-IPN amphoteric membranes exhibit better stability than pure SPAES membrane, as demonstrated by thermogravimetric analysis and ex situ immersion testing results. More importantly, it is shown that the amphoteric membrane can effectively hinder vanadium ion crossover through the membrane, which is attributed to the semi-IPN structure and Donnan exclusion. As expected, the amphoteric membrane containing 20% VMPSU exhibits the highest proton selectivity (6.86 × 10⁴ S min cm⁻³), comparing to pristine SPAES (1.90 × 10⁴ S min cm⁻³) as well as Nafion117 (1.31 × 10⁴ S min cm⁻³).     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

Modified Sulfonated Poly(ether ether ketone) Based Mixed Matrix Membranes for Direct Methanol Fuel Cells

Mixed matrix membranes based on zeolite 4A‐methane sulfonic acid (MSA)‐sulfonated poly(ether ether ketone) (SPEEK) are evaluated as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cells (DMFCs). Ion‐exchange capacity, sorption of water, and water–methanol mixture, proton conductivity, and methanol permeability for the mixed‐matrix membranes have been extensively investigated. The mixed‐matrix membranes are also characterized for their cross‐sectional morphology, mechanical, and thermal properties. DMFCs employing SPEEK‐MSA (20 wt.%) blend, zeolite 4A (4 wt.%)‐SPEEK‐MSA (20 wt.%) mixed matrix membranes deliver peak power densities of 130 and 159 mW cm^–2, respectively; while a peak power density of only 95 mW cm^–2 is obtained for the DMFC employing pristine SPEEK membrane at 70 °C. The results showed that these SPEEK based mixed matrix membranes exhibit higher DMFC performance and lower methanol permeability in comparison to Nafion‐117 membrane.     

Partially Sulfonated Poly(1,4‐phenylene ether‐ether‐sulfone) and Poly(vinylidene fluoride) Blend Membranes for Fuel Cells

Blend membranes based on high conductive sulfonated poly(1,4‐phenylene ether‐ether‐sulfone) (SPEES) and poly(vinylidene fluoride) (PVDF) having excellent chemical stability were prepared and characterized for direct methanol fuel cells. The effects of PVDF content on the proton conductivity, water uptake, and chemical stability of SPEES/PVDF blend membranes were investigated. The morphology, miscibility, thermal, and mechanical properties of blend membranes were also studied by means of scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA) measurements. The blend membrane containing 90 wt.% SPEES (degree of sulfonation – DS = 72%) and 10 wt.% PVDF (M_w = 180,000) exhibits optimum properties among various SPEES72/PVDF membranes. Addition of PVDF enhanced resistance of the SPEES membrane against peroxide radicals and methanol significantly without deterioration of its proton conductivity. It's proton conductivity at 80 °C and 100% relative humidity is higher than Nafion 115 while it's methanol permeability is only half of that of Nafion 115 at 80 °C. The direct methanol fuel cell performance of the SPEES membranes was better than that of Nafion 115 membrane at 80 °C.     

Performance evaluation of sodium alginate–Pebax polyion complex membranes for application in direct methanol fuel cells

A novel polyion complex membrane was synthesized for direct methanol fuel cell application through the blending of the natural biopolymer sodium alginate (SA) with the synthetic polymer Pebax [poly(ether‐block ‐amide)]. The blend was covalently crosslinked with glutaraldehyde (GA) and sulfonated with sulfuric acid (H₂SO₄), after which characterization by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffractometry, thermogravimetric analysis, and universal testing machine techniques was carried out. The SA–Pebax–GA–H₂SO₄ membrane exhibited a high ion‐exchange capacity of 2.1 mequiv/g, an optimum water sorption of 17.3%, and a low methanol sorption of 9.5%. A desirably low methanol permeability of 9.25 × 10^?8 cm²/s and a high proton conductivity of 0.067 S/cm were obtained as against corresponding values of 1.82 × 10^?6 cm²/s and 0.077 S/cm reported for a commercial Nafion 117 membrane. Moreover, a high selectivity of 6.5 × 10⁵ Ss/cm³ with a power density of 0.17 W/cm² was achieved with the indigenous blend membrane at a potential of 0.34 V. Molecular dynamics simulation was performed along with the estimation of fractional free volume to explain the transport behavior of water and methanol molecules through the membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44485.     

Synthesis and characterization of acid–base polyimides bearing pendant sulfoalkoxy groups for direct methanol fuel cell applications

A series of acid–base polyimides with sulfonic acid groups in the side chains have been prepared, based on a new synthesized sulfonated diamine monomer containing pyridine functional group. The effect of the introduction of pyridine groups into copolymer backbone on the properties of membrane were evaluated through the investigation of membrane parameters. The copolymers produced flexible, tough, and transparent membranes by solvent casting method. All the prepared membranes displayed high thermal stability, great oxidative stability and good mechanical properties. They exhibited appropriate water uptake (15.8–30.2 wt % at 80°C) and remarkable dimensional stability (2.5–6.9% at 80°C). The proton conductivity of SPI‐80 was 1.01 × 10^?2 S cm^?1 at room temperature. Moreover, the methanol permeability of SPI‐80 membrane was 1.22 × 10^?7 cm² s^?1, which was lower than 23.8 × 10^?7 cm² s^?1 of Nafion 117. Therefore, these acid‐base polyimides materials have a promising prospect for direct methanol fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42238.     

Preparation of chitosan-modified core–shell SiO2-acidic polymer multiple crosslinked membranes

This article prepares and studies a series of chitosan-modified core–shell SiO₂-acidic polymer multiple crosslinked membranes (modified membranes). The preparation process is simple, low cost, and environmentally friendly. The multiple crosslinking enhances the thermal stability and mechanical strength of membranes. TGA shows that the 10% weight loss temperatures of modified membranes are above 300 °C. Compared with water uptake, the methanol absorption of modified membranes is lower and decreases with increasing methanol concentration, which is very beneficial to their use in direct-methanol fuel cells. The lowest methanol diffusion coefficient of the modified membrane is 4.56 × 10⁻⁸ cm² s⁻¹, which is only about 1/50th of that of Nafion117. In addition, the membranes exhibit feasible proton conductivity and higher selectivity than Nafion117. These results indicate that the chitosan-modified core–shell SiO₂-acidic polymer multiple crosslinked membranes have potential applications in direct-methanol fuel cells. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48494.